Frontpage > Home Improvement > Nails, Screws & Fasteners > Wedge Anchors

Best Wedge Anchors - Buying Guide

Last Updated: 09/21/2019

Share on


  #1

CONFAST 1/2" x 4-1/4" Wedge Anchor Zinc Plated (Box of 25)

 PartNumber: WA12414   |   Asin: B071ZDZ4Y7

Applications
The anchor is made from Carbon Steel, and is Zinc Plated. This anchor is designed for use in Concrete only, and should never be used in block or brick base material.

Environment
The anchor is designed for use in a Dry environment.

Hole Diameter/Bit Diameter
The anchor requires a 1/2" hole to be drilled in the base material (Concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.

Diameter of Anchor
The diameter of the anchor is 1/2".

Length Anchor
The length of the anchor is 4-1/4"

Thread Length
The length of the threads on the anchor is 2-3/4" in length.

Minimum Embedment
The minimum anchor embedment into the concrete is 2-1/4". Therefore, the anchor must be installed so that a minimum of 2-1/4" of the anchor is embedded into the concrete.

Maximum Fixture Thickness
The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 1-1/2". This will ensure that the minimum embedment of 2-1/4" will be met.

Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 1/2" diameter anchor requires the hole in the fixture to be 5/8".

Torque Value
To be set properly in the concrete, the anchor must be torqued to between 50 - 60 ft./lbs.

Spacing between Anchors
Each anchor must be spaced a minimum distance of 5" from each other when measured center to center.

Edge Distance
It is very important not to install the anchor any closer than 2-1/2" from an unsupported edge of the concrete.

Features

  • ZINC PLATED - Helps prevent rust in dry environments
  • WIDE RANGE OF SIZES - Insures proper fastener for best results
  • PACKAGED WITH NUTS AND WASHERS - Fast, quick, complete installation
  • HOLE SIZE IS ANCHOR SIZE - Simplicity and ease of installation
  • See more on Amazon...

Brand: CONFAST   |   Manufacturer: CONFAST

Package Dimensions: 3.43 x 4.61 x 6.69 inches (8.7 x 11.7 x 17.0 cm)

Amazon Price: $22.99 | as of 09/21/2019(4:33pm pst)
Availibility: Usually ships in 24 hours
List Price: $22.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #2

CONFAST 1/2" x 5-1/2" Wedge Anchor Zinc Plated (Box of 25)

 PartNumber: WA12512   |   Asin: B0723988J3

Applications
The anchor is made from Carbon Steel, and is Zinc Plated. This anchor is designed for use in Concrete only, and should never be used in block or brick base material.

Environment
The anchor is designed for use in a Dry environment.

Hole Diameter/Bit Diameter
The anchor requires a 1/2" hole to be drilled in the base material (Concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.

Diameter of Anchor
The diameter of the anchor is 1/2".

Length Anchor
The length of the anchor is 5-1/2"

Thread Length
The length of the threads on the anchor is 4" in length.

Minimum Embedment
The minimum anchor embedment into the concrete is 2-1/4". Therefore, the anchor must be installed so that a minimum of 2-1/4" of the anchor is embedded into the concrete.

Maximum Fixture Thickness
The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 2-3/4". This will ensure that the minimum embedment of 2-1/4" will be met.

Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 1/2" diameter anchor requires the hole in the fixture to be 5/8".

Torque Value
To be set properly in the concrete, the anchor must be torqued to between 50 - 60 ft./lbs.

Spacing between Anchors
Each anchor must be spaced a minimum distance of 5" from each other when measured center to center.

Edge Distance
It is very important not to install the anchor any closer than 2-1/2" from an unsupported edge of the concrete.

Features

  • ZINC PLATED - Helps prevent rust in dry environments
  • WIDE RANGE OF SIZES - Insures proper fastener for best results
  • PACKAGED WITH NUTS AND WASHERS - Fast, quick, complete installation
  • HOLE SIZE IS ANCHOR SIZE - Simplicity and ease of installation
  • See more on Amazon...

Brand: CONFAST   |   Manufacturer: CONFAST

Package Dimensions: 3.39 x 4.8 x 6.73 inches (8.6 x 12.2 x 17.1 cm)

Amazon Price: $23.99 | as of 09/21/2019(4:33pm pst)
Availibility: Usually ships in 24 hours
List Price: $23.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #3

Simpson Strong Tie STB2-50334 1/2-Inch by 3-3/4-Inch Bolt Wedge Anchor for Cracked and Uncracked Concrete, 25-Pack

Model: STB2-50334   |    Mpn: STB2-50334   |    Ean: 0767654964477   |    PartNumber: STB2-50334   |   Asin: B0091N7T4C

The Strong-Bolt is wedge anchor designed for optimum performance in both cracked and uncracked concrete: a requirement that the 2009 IBC places on post-installed anchors. The Strong-Bolt anchor is proven to offer increased reliability in the most adverse conditions, including cracked concrete under static and seismic loading. The proprietary tri-segmented clip has dual undercutting embossments on each segment which enable secondary or follow-up expansion if a crack forms and intersects the anchor location.

Features

  • Independently adjustable tri-segment clip for follow-up expansion
  • Dual embossments on each clip segment
  • Installs like a standard wedge anchor
  • Head is stamped with Simpson sign and size ID
  • No need for special bits or installation tools
  • See more on Amazon...

Brand: Simpson Strong-Tie   |   Manufacturer: Anchor Fasteners

Item Dimensions: 6 x 4 x 4 inches (15.2 x 10.2 x 10.2 cm)   |   Package Dimensions: 3.39 x 3.62 x 6.85 inches (8.6 x 9.2 x 17.4 cm)

Amazon Price: $16.00 | as of 09/21/2019(4:33pm pst)
Availibility: Usually ships in 24 hours
List Price: $22.96 | Used Price: $20.20

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #4

CONFAST 1/2" x 3-3/4" Wedge Anchor Zinc Plated (Box of 25)

 PartNumber: WA12334   |   Asin: B071P6WLSS

Applications
The anchor is made from Carbon Steel, and is Zinc Plated. This anchor is designed for use in Concrete only, and should never be used in block or brick base material.

Environment
The anchor is designed for use in a Dry environment.

Hole Diameter/Bit Diameter
The anchor requires a 1/2" hole to be drilled in the base material (Concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.

Diameter of Anchor
The diameter of the anchor is 1/2".

Length Anchor
The length of the anchor is 3-3/4"

Thread Length
The length of the threads on the anchor is 2-1/4" in length.

Minimum Embedment
The minimum anchor embedment into the concrete is 2-1/4". Therefore, the anchor must be installed so that a minimum of 2-1/4" of the anchor is embedded into the concrete.

Maximum Fixture Thickness
The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 1". This will ensure that the minimum embedment of 2-1/4" will be met.

Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 1/2" diameter anchor requires the hole in the fixture to be 5/8".

Torque Value
To be set properly in the concrete, the anchor must be torqued to between 50 - 60 ft./lbs.

Spacing between Anchors
Each anchor must be spaced a minimum distance of 5" from each other when measured center to center.

Edge Distance
It is very important not to install the anchor any closer than 2-1/2" from an unsupported edge of the concrete.

Features

  • ZINC PLATED - Helps prevent rust in dry environments
  • WIDE RANGE OF SIZES - Insures proper fastener for best results
  • PACKAGED WITH NUTS AND WASHERS - Fast, quick, complete installation
  • HOLE SIZE IS ANCHOR SIZE - Simplicity and ease of installation
  • See more on Amazon...

Brand: CONFAST   |   Manufacturer: CONFAST

Package Dimensions: 3.35 x 4.53 x 6.57 inches (8.5 x 11.5 x 16.7 cm)

Amazon Price: $22.99 | as of 09/21/2019(4:33pm pst)
Availibility: Usually ships in 24 hours
List Price: $22.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #5

CONFAST 3/8" x 3-3/4" Wedge Anchor Zinc Plated (Box of 50)

 PartNumber: WA38334   |   Asin: B072397QR3

Applications
The anchor is made from Carbon Steel, and is Zinc Plated. This anchor is designed for use in Concrete only, and should never be used in block or brick base material.

Environment
The anchor is designed for use in a Dry environment.

Hole Diameter/Bit Diameter
The anchor requires a 3/8" hole to be drilled in the base material (Concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.

Diameter of Anchor
The diameter of the anchor is 3/8".

Length Anchor
The length of the anchor is 3-3/4"

Thread Length
The length of the threads on the anchor is 2-1/2" in length.

Minimum Embedment
The minimum anchor embedment into the concrete is 1-1/2". Therefore, the anchor must be installed so that a minimum of 1-1/2" of the anchor is embedded into the concrete.

Maximum Fixture Thickness
The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 1-7/8". This will ensure that the minimum embedment of 1-1/2" will be met.

Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 3/8" diameter anchor requires the hole in the fixture to be 1/2".

Torque Value
To be set properly in the concrete, the anchor must be torqued to between 25 - 30 ft./lbs.

Spacing between Anchors
Each anchor must be spaced a minimum distance of 3-3/4" from each other when measured center to center.

Edge Distance
It is very important not to install the anchor any closer than 1-7/8" from an unsupported edge of the concrete.

Features

  • ZINC PLATED - Helps prevent rust in dry environments
  • WIDE RANGE OF SIZES - Insures proper fastener for best results
  • PACKAGED WITH NUTS AND WASHERS - Fast, quick, complete installation
  • HOLE SIZE IS ANCHOR SIZE - Simplicity and ease of installation
  • See more on Amazon...

Brand: CONFAST   |   Manufacturer: CONFAST

Package Dimensions: 3.39 x 4.49 x 6.61 inches (8.6 x 11.4 x 16.8 cm)

Amazon Price: $24.99 | as of 09/21/2019(4:33pm pst)
Availibility: Usually ships in 24 hours
List Price: $24.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #6

Rotary Lift Installation install Kit -16 Wedge Anchor Bolts & 30 pack shims pack

 Ean: 0654554856851   |   Asin: B01MS5A418

Features

  • This is a lift installation kit that helps you install your used auto lift or move a lift from one bay to another.
  • It will work on most 2 post lifts and some 4 post lifts as well. It provides the lag bolts / wedge anchors as well as a large assortment of shims to level the lifts columns.
  • Our kit will includes the the following: (16) Zinc Plated Wedge Anchors that measure 5-1/2 x 3/4 and have the buts and washers already in place and ready to install in the ground.
  • 30 piece shim kit -10 shims in three different thicknesses - 1/16 blue shims , 1/8 red shims, 1/4 black shim.
  • We install at least 3 lifts a day with this exact kit so we know it works ! All Wedge Anchors meet ALL ANSI Safety Standards
  • See more on Amazon...

Brand: LUCKY   |   Manufacturer: Imported

Amazon Price: $49.51 | as of 09/21/2019(4:33pm pst)
Availibility: Usually ships in 24 hours
List Price: $54.00

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #7

CONFAST 3/4" x 7" Wedge Anchor Zinc Plated (Box of 10)

 PartNumber: WA347   |   Asin: B072PRJXNJ

Applications
The anchor is made from Carbon Steel, and is Zinc Plated. This anchor is designed for use in Concrete only, and should never be used in block or brick base material.

Environment
The anchor is designed for use in a Dry environment.

Hole Diameter/Bit Diameter
The anchor requires a 3/4" hole to be drilled in the base material (Concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.

Diameter of Anchor
The diameter of the anchor is 3/4".

Length Anchor
The length of the anchor is 7"

Thread Length
The length of the threads on the anchor is 4" in length.

Minimum Embedment
The minimum anchor embedment into the concrete is 3-1/4". Therefore, the anchor must be installed so that a minimum of 3-1/4" of the anchor is embedded into the concrete.

Maximum Fixture Thickness
The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 3". This will ensure that the minimum embedment of 3-1/4" will be met.

Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 3/4" diameter anchor requires the hole in the fixture to be 1".

Torque Value
To be set properly in the concrete, the anchor must be torqued to between 150 - 175 ft./lbs.

Spacing between Anchors
Each anchor must be spaced a minimum distance of 7-1/2" from each other when measured center to center.

Edge Distance
It is very important not to install the anchor any closer than 3-3/4" from an unsupported edge of the concrete.

Features

  • ZINC PLATED - Helps prevent rust in dry environments
  • WIDE RANGE OF SIZES - Insures proper fastener for best results
  • PACKAGED WITH NUTS AND WASHERS - Fast, quick, complete installation
  • HOLE SIZE IS ANCHOR SIZE - Simplicity and ease of installation
  • See more on Amazon...

Brand: CONFAST   |   Manufacturer: CONFAST

Package Dimensions: 2.8 x 6.4 x 9.3 inches (7.1 x 16.3 x 23.6 cm)

Amazon Price: $33.99 | as of 09/21/2019(4:33pm pst)
Availibility: Usually ships in 24 hours
List Price: $33.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #8

The Hillman Group 370984 Wedge Anchor, 3/8 X 3-Inch, 25-Pack

Model: 370984   |    Mpn: 370984   |    Ean: 0008236433401   |    PartNumber: 370984   |   Asin: B000CZ4JTG

The Power-Stud+ SD1 is a fully threaded, torque controlled, wedge expansion anchor that is designed for concrete applications. Suitable base materials are normal-weight and sand-lightweight concrete, concrete over steel deck, and grouted concrete masonry. This anchor has various DOT approvals including Caltrans listing for "Stud Mechanical Expansion Anchors". Building code approved.

Features

  • Zinc-plated wedge anchors designed for consistent performance in cracked and un-cracked concrete
  • Suitable base materials are normal-weight, sand-lightweight concrete, concrete over steel deck, and grouted concrete masonry
  • Common applications include structural connections such as beam and column anchorage
  • Nominal drill bit size is the same as the anchor diameter
  • Anchor can be installed through standard fixture holes
  • 25 pieces per retail package
  • See more on Amazon...

Brand: Hillman   |   Manufacturer: The Hillman Group

Item Dimensions: 2.5 x 3.4 x 4.5 inches (6.4 x 8.6 x 11.4 cm)   |   Package Dimensions: 2.6 x 3.4 x 4.3 inches (6.6 x 8.6 x 10.9 cm)

Amazon Price: $19.73 | as of 09/21/2019(4:33pm pst)
Availibility: Usually ships in 24 hours
List Price: $20.74

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #9

CONFAST 3/4" x 10" Wedge Anchor Zinc Plated (Box of 10)

 PartNumber: WA3410   |   Asin: B0717461C7

Applications
The anchor is made from Carbon Steel, and is Zinc Plated. This anchor is designed for use in Concrete only, and should never be used in block or brick base material.

Environment
The anchor is designed for use in a Dry environment.

Hole Diameter/Bit Diameter
The anchor requires a 3/4" hole to be drilled in the base material (Concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.

Diameter of Anchor
The diameter of the anchor is 3/4".

Length Anchor
The length of the anchor is 10"

Thread Length
The length of the threads on the anchor is 4" in length.

Minimum Embedment
The minimum anchor embedment into the concrete is 3-1/4". Therefore, the anchor must be installed so that a minimum of 3-1/4" of the anchor is embedded into the concrete.

Maximum Fixture Thickness
The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 6". This will ensure that the minimum embedment of 3-1/4" will be met.

Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 3/4" diameter anchor requires the hole in the fixture to be 1".

Torque Value
To be set properly in the concrete, the anchor must be torqued to between 150 - 175 ft./lbs.

Spacing between Anchors
Each anchor must be spaced a minimum distance of 7-1/2" from each other when measured center to center.

Edge Distance
It is very important not to install the anchor any closer than 3-3/4" from an unsupported edge of the concrete.

Features

  • ZINC PLATED - Helps prevent rust in dry environments
  • WIDE RANGE OF SIZES - Insures proper fastener for best results
  • PACKAGED WITH NUTS AND WASHERS - Fast, quick, complete installation
  • HOLE SIZE IS ANCHOR SIZE - Simplicity and ease of installation
  • See more on Amazon...

Brand: CONFAST   |   Manufacturer: CONFAST

Package Dimensions: 3.03 x 4.61 x 12.72 inches (7.7 x 11.7 x 32.3 cm)

Amazon Price: $50.99 | as of 09/21/2019(4:33pm pst)
Availibility: Usually ships in 24 hours
List Price: $50.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #10

(10) Galvanized Concrete Wedge Anchor Bolts 1/2 x 10 Includes Nuts & Washers

 PartNumber: 361686181126   |   Asin: B01N2ADZD2

Lot of (10) wedge anchor bolts.

These galvanized anchors are 1/2-13 thread and are 10" in length.

Nuts and flat washers are included.

Features

Brand: Lexar Industrial   |   Manufacturer: Lexar Industrial

Amazon Price: $38.99 | as of 09/21/2019(4:33pm pst)
Availibility: Usually ships in 1-2 business days
List Price: $38.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #11

CONFAST 3/8" x 5" Wedge Anchor Zinc Plated (Box of 50)

 PartNumber: WA385   |   Asin: B072FNBG16

Applications
The anchor is made from Carbon Steel, and is Zinc Plated. This anchor is designed for use in Concrete only, and should never be used in block or brick base material.

Environment
The anchor is designed for use in a Dry environment.

Hole Diameter/Bit Diameter
The anchor requires a 3/8" hole to be drilled in the base material (Concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.

Diameter of Anchor
The diameter of the anchor is 3/8".

Length Anchor
The length of the anchor is 5"

Thread Length
The length of the threads on the anchor is 3-3/4" in length.

Minimum Embedment
The minimum anchor embedment into the concrete is 1-1/2". Therefore, the anchor must be installed so that a minimum of 1-1/2" of the anchor is embedded into the concrete.

Maximum Fixture Thickness
The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 3-1/8". This will ensure that the minimum embedment of 1-1/2" will be met.

Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 3/8" diameter anchor requires the hole in the fixture to be 1/2".

Torque Value
To be set properly in the concrete, the anchor must be torqued to between 25 - 30 ft./lbs.

Spacing between Anchors
Each anchor must be spaced a minimum distance of 3-3/4" from each other when measured center to center.

Edge Distance
It is very important not to install the anchor any closer than 1-7/8" from an unsupported edge of the concrete.

Features

  • ZINC PLATED - Helps prevent rust in dry environments
  • WIDE RANGE OF SIZES - Insures proper fastener for best results
  • PACKAGED WITH NUTS AND WASHERS - Fast, quick, complete installation
  • HOLE SIZE IS ANCHOR SIZE - Simplicity and ease of installation
  • See more on Amazon...

Brand: CONFAST   |   Manufacturer: CONFAST

Package Dimensions: 2.5 x 6.4 x 9.8 inches (6.4 x 16.3 x 24.9 cm)

Amazon Price: $30.99 | as of 09/21/2019(4:33pm pst)
Availibility: Usually ships in 24 hours
List Price: $30.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #12

Strong Bolt STB2-50700 Wedge Anchor 1/2-Inch by 7-Inch, 25-Piece

Model: STB2-50700   |    Mpn: STB2-50700   |    Ean: 0707392176022   |    PartNumber: STB2-50700   |   Asin: B0091N7TUQ

The Strong-Bolt 2 wedge anchor is the next generation solution for cracked and uncracked concrete. Following rigorous testing according to ICC-ES acceptance criteria, the Strong-Bolt 2 anchor received classification as a Category 1 anchor, the highest attainable anchor category for performance in cracked concrete under static and seimic loading. Code listed by ICC-ES under the 2009 IBC requirements for post-installed anchors in cracked and uncracked concrete.

Features

  • Tri-segmented clip
  • Dual embossments on each clip segment
  • High-strength alloy clip on carbon-steel anchors
  • Length identification on head of fastener
  • Category 1 anchor classification
  • See more on Amazon...

Brand: Simpson Strong-Tie   |   Manufacturer: Anchor Fasteners

Item Dimensions: 8 x 4 x 4 inches (20.3 x 10.2 x 10.2 cm)   |   Package Dimensions: 3.5 x 3.75 x 7.75 inches (8.9 x 9.5 x 19.7 cm)

Amazon Price: $27.65 | as of 09/21/2019(4:33pm pst)
Availibility: Usually ships in 24 hours
List Price: $27.67

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #13

CONFAST 1/2" x 7" Wedge Anchor Zinc Plated (Box of 25)

Model: .   |    Mpn: WA127   |    PartNumber: WA127   |   Asin: B0711XRTQF

Applications
The anchor is made from Carbon Steel, and is Zinc Plated. This anchor is designed for use in Concrete only, and should never be used in block or brick base material.

Environment
The anchor is designed for use in a Dry environment.

Hole Diameter/Bit Diameter
The anchor requires a 1/2" hole to be drilled in the base material (Concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.

Diameter of Anchor
The diameter of the anchor is 1/2".

Length Anchor
The length of the anchor is 7"

Thread Length
The length of the threads on the anchor is 4" in length.

Minimum Embedment
The minimum anchor embedment into the concrete is 2-1/4". Therefore, the anchor must be installed so that a minimum of 2-1/4" of the anchor is embedded into the concrete.

Maximum Fixture Thickness
The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 4-1/4". This will ensure that the minimum embedment of 2-1/4" will be met.

Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 1/2" diameter anchor requires the hole in the fixture to be 5/8".

Torque Value
To be set properly in the concrete, the anchor must be torqued to between 50 - 60 ft./lbs.

Spacing between Anchors
Each anchor must be spaced a minimum distance of 5" from each other when measured center to center.

Edge Distance
It is very important not to install the anchor any closer than 2-1/2" from an unsupported edge of the concrete.

Features

  • ZINC PLATED - Helps prevent rust in dry environments
  • WIDE RANGE OF SIZES - Insures proper fastener for best results
  • PACKAGED WITH NUTS AND WASHERS - Fast, quick, complete installation
  • HOLE SIZE IS ANCHOR SIZE - Simplicity and ease of installation
  • See more on Amazon...

Brand: CONFAST   |   Manufacturer: CONFAST

Package Dimensions: 3.5 x 4.5 x 9.2 inches (8.9 x 11.4 x 23.4 cm)

Amazon Price: $27.39 | as of 09/21/2019(4:33pm pst)
Availibility: Usually ships in 24 hours
List Price: $27.39

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #14

CONFAST 3/4" x 5-1/2" Wedge Anchor Zinc Plated (Box of 20)

 PartNumber: WA34512   |   Asin: B071SDDB2B

Applications
The anchor is made from Carbon Steel, and is Zinc Plated. This anchor is designed for use in Concrete only, and should never be used in block or brick base material.

Environment
The anchor is designed for use in a Dry environment.

Hole Diameter/Bit Diameter
The anchor requires a 3/4" hole to be drilled in the base material (Concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.

Diameter of Anchor
The diameter of the anchor is 3/4".

Length Anchor
The length of the anchor is 5-1/2"

Thread Length
The length of the threads on the anchor is 3-1/4" in length.

Minimum Embedment
The minimum anchor embedment into the concrete is 3-1/4". Therefore, the anchor must be installed so that a minimum of 3-1/4" of the anchor is embedded into the concrete.

Maximum Fixture Thickness
The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 1-1/2". This will ensure that the minimum embedment of 3-1/4" will be met.

Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 3/4" diameter anchor requires the hole in the fixture to be 1".

Torque Value
To be set properly in the concrete, the anchor must be torqued to between 150 - 175 ft./lbs.

Spacing between Anchors
Each anchor must be spaced a minimum distance of 7-1/2" from each other when measured center to center.

Edge Distance
It is very important not to install the anchor any closer than 3-3/4" from an unsupported edge of the concrete.

Features

  • ZINC PLATED - Helps prevent rust in dry environments
  • WIDE RANGE OF SIZES - Insures proper fastener for best results
  • PACKAGED WITH NUTS AND WASHERS - Fast, quick, complete installation
  • HOLE SIZE IS ANCHOR SIZE - Simplicity and ease of installation
  • See more on Amazon...

Brand: CONFAST   |   Manufacturer: CONFAST

Package Dimensions: 3 x 4.9 x 12.2 inches (7.6 x 12.4 x 31.0 cm)

Amazon Price: $46.99 | as of 09/21/2019(4:33pm pst)
Availibility: Usually ships in 24 hours
List Price: $46.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #15

CONFAST 3/4" x 6-1/4" Wedge Anchor Zinc Plated (Box of 20)

 PartNumber: WA34614   |   Asin: B071LM9RNT

Applications
The anchor is made from Carbon Steel, and is Zinc Plated. This anchor is designed for use in Concrete only, and should never be used in block or brick base material.

Environment
The anchor is designed for use in a Dry environment.

Hole Diameter/Bit Diameter
The anchor requires a 3/4" hole to be drilled in the base material (Concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.

Diameter of Anchor
The diameter of the anchor is 3/4".

Length Anchor
The length of the anchor is 6-1/4"

Thread Length
The length of the threads on the anchor is 4" in length.

Minimum Embedment
The minimum anchor embedment into the concrete is 3-1/4". Therefore, the anchor must be installed so that a minimum of 3-1/4" of the anchor is embedded into the concrete.

Maximum Fixture Thickness
The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 2-1/4". This will ensure that the minimum embedment of 3-1/4" will be met.

Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 3/4" diameter anchor requires the hole in the fixture to be 1".

Torque Value
To be set properly in the concrete, the anchor must be torqued to between 150 - 175 ft./lbs.

Spacing between Anchors
Each anchor must be spaced a minimum distance of 7-1/2" from each other when measured center to center.

Edge Distance
It is very important not to install the anchor any closer than 3-3/4" from an unsupported edge of the concrete.

Features

  • ZINC PLATED - Helps prevent rust in dry environments
  • WIDE RANGE OF SIZES - Insures proper fastener for best results
  • PACKAGED WITH NUTS AND WASHERS - Fast, quick, complete installation
  • HOLE SIZE IS ANCHOR SIZE - Simplicity and ease of installation
  • See more on Amazon...

Brand: CONFAST   |   Manufacturer: CONFAST

Package Dimensions: 4.4 x 6.1 x 12.5 inches (11.2 x 15.5 x 31.8 cm)

Amazon Price: $51.99 | as of 09/21/2019(4:33pm pst)
Availibility: Usually ships in 24 hours
List Price: $51.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #16

CONFAST 5/8" x 6" Wedge Anchor Zinc Plated (Box of 20)

 PartNumber: WA586   |   Asin: B072C2P35Y

Applications
The anchor is made from Carbon Steel, and is Zinc Plated. This anchor is designed for use in Concrete only, and should never be used in block or brick base material.

Environment
The anchor is designed for use in a Dry environment.

Hole Diameter/Bit Diameter
The anchor requires a 5/8" hole to be drilled in the base material (Concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.

Diameter of Anchor
The diameter of the anchor is 5/8".

Length Anchor
The length of the anchor is 6"

Thread Length
The length of the threads on the anchor is 4" in length.

Minimum Embedment
The minimum anchor embedment into the concrete is 2-3/4". Therefore, the anchor must be installed so that a minimum of 2-3/4" of the anchor is embedded into the concrete.

Maximum Fixture Thickness
The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 2-5/8". This will ensure that the minimum embedment of 2-3/4" will be met.

Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 5/8" diameter anchor requires the hole in the fixture to be 7/8".

Torque Value
To be set properly in the concrete, the anchor must be torqued to between 75 - 90 ft./lbs.

Spacing between Anchors
Each anchor must be spaced a minimum distance of 6-1/4" from each other when measured center to center.

Edge Distance
It is very important not to install the anchor any closer than 3-1/8" from an unsupported edge of the concrete.

Features

  • ZINC PLATED - Helps prevent rust in dry environments
  • WIDE RANGE OF SIZES - Insures proper fastener for best results
  • PACKAGED WITH NUTS AND WASHERS - Fast, quick, complete installation
  • HOLE SIZE IS ANCHOR SIZE - Simplicity and ease of installation
  • See more on Amazon...

Brand: CONFAST   |   Manufacturer: CONFAST

Package Dimensions: 2.44 x 6.22 x 9.37 inches (6.2 x 15.8 x 23.8 cm)

Amazon Price: $30.99 | as of 09/21/2019(4:33pm pst)
Availibility: Usually ships in 24 hours
List Price: $30.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #17

CONFAST 3/8" x 3" Stainless Steel Wedge Anchor (50 per Box)

 PartNumber: WAS383   |   Asin: B072MP78K6

Applications
The anchor is made from 304 Stainless Steel. This anchor is designed for use in Concrete only, and should never be used in block or brick base material.

Environment
The anchor is designed for use in a Wet environment.

Hole Diameter/Bit Diameter
The anchor requires a 3/8" hole to be drilled in the base material (Concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.

Diameter of Anchor
The diameter of the anchor is 3/8".

Length Anchor
The length of the anchor is 3"

Thread Length
The length of the threads on the anchor is 1-1/2" in length.

Minimum Embedment
The minimum anchor embedment into the concrete is 1-1/2". Therefore, the anchor must be installed so that a minimum of 1-1/2" of the anchor is embedded into the concrete.

Maximum Fixture Thickness
The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 1-1/8". This will ensure that the minimum embedment of 1-1/2" will be met.

Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 3/8" diameter anchor requires the hole in the fixture to be 1/2".

Torque Value
To be set properly in the concrete, the anchor must be torqued to between 25 - 30 ft./lbs.

Spacing between Anchors
Each anchor must be spaced a minimum distance of 3-3/4" from each other when measured center to center.

Edge Distance
It is very important not to install the anchor any closer than 1-7/8" from an unsupported edge of the concrete.

Features

  • MADE FROM 304 STAINLESS STEEL - Can be used in wet, submerged environments and will not rust
  • WIDE RANGE OF SIZES - Insures proper fastener for best results
  • PACKAGED WITH NUTS AND WASHERS - Fast, quick, complete installation
  • HOLE SIZE IS ANCHOR SIZE - Simplicity and ease of installation
  • See more on Amazon...

Brand: CONFAST   |   Manufacturer: CONFAST

Package Dimensions: 3.03 x 4.69 x 4.72 inches (7.7 x 11.9 x 12.0 cm)

Amazon Price: $60.99 | as of 09/21/2019(4:33pm pst)
Availibility: Usually ships in 24 hours
List Price: $60.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #18

CONFAST 1/4" x 2-1/4" Wedge Anchor Zinc Plated (Box of 100)

 PartNumber: WA14214   |   Asin: B072LTSW41

Applications
The anchor is made from Carbon Steel, and is Zinc Plated. This anchor is designed for use in Concrete only, and should never be used in block or brick base material.

Environment
The anchor is designed for use in a Dry environment.

Hole Diameter/Bit Diameter
The anchor requires a 1/4" hole to be drilled in the base material (Concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.

Diameter of Anchor
The diameter of the anchor is 1/4".

Length Anchor
The length of the anchor is 2-1/4"

Thread Length
The length of the threads on the anchor is 1-1/4" in length.

Minimum Embedment
The minimum anchor embedment into the concrete is 1-1/8". Therefore, the anchor must be installed so that a minimum of 1-1/8" of the anchor is embedded into the concrete.

Maximum Fixture Thickness
The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 7/8". This will ensure that the minimum embedment of 1-1/8" will be met.

Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 1/4" diameter anchor requires the hole in the fixture to be 5/16".

Torque Value
To be set properly in the concrete, the anchor must be torqued to between 5 - 10 ft./lbs.

Spacing between Anchors
Each anchor must be spaced a minimum distance of 2-1/2" from each other when measured center to center.

Edge Distance
It is very important not to install the anchor any closer than 1-1/4" from an unsupported edge of the concrete.

Features

  • ZINC PLATED - Helps prevent rust in dry environments
  • WIDE RANGE OF SIZES - Insures proper fastener for best results
  • PACKAGED WITH NUTS AND WASHERS - Fast, quick, complete installation
  • HOLE SIZE IS ANCHOR SIZE - Simplicity and ease of installation
  • See more on Amazon...

Brand: CONFAST   |   Manufacturer: CONFAST

Package Dimensions: 3.11 x 3.58 x 6.1 inches (7.9 x 9.1 x 15.5 cm)

Amazon Price: $22.99 | as of 09/21/2019(4:33pm pst)
Availibility: Usually ships in 24 hours
List Price: $22.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #19

CONFAST 5/8" x 5" Wedge Anchor Zinc Plated (Box of 20)

 PartNumber: WA585   |   Asin: B071FFSBQ6

Applications
The anchor is made from Carbon Steel, and is Zinc Plated. This anchor is designed for use in Concrete only, and should never be used in block or brick base material.

Environment
The anchor is designed for use in a Dry environment.

Hole Diameter/Bit Diameter
The anchor requires a 5/8" hole to be drilled in the base material (Concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.

Diameter of Anchor
The diameter of the anchor is 5/8".

Length Anchor
The length of the anchor is 5"

Thread Length
The length of the threads on the anchor is 3" in length.

Minimum Embedment
The minimum anchor embedment into the concrete is 2-3/4". Therefore, the anchor must be installed so that a minimum of 2-3/4" of the anchor is embedded into the concrete.

Maximum Fixture Thickness
The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 1-5/8". This will ensure that the minimum embedment of 2-3/4" will be met.

Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 5/8" diameter anchor requires the hole in the fixture to be 7/8".

Torque Value
To be set properly in the concrete, the anchor must be torqued to between 75 - 90 ft./lbs.

Spacing between Anchors
Each anchor must be spaced a minimum distance of 6-1/4" from each other when measured center to center.

Edge Distance
It is very important not to install the anchor any closer than 3-1/8" from an unsupported edge of the concrete.

Features

  • ZINC PLATED - Helps prevent rust in dry environments
  • WIDE RANGE OF SIZES - Insures proper fastener for best results
  • PACKAGED WITH NUTS AND WASHERS - Fast, quick, complete installation
  • HOLE SIZE IS ANCHOR SIZE - Simplicity and ease of installation
  • See more on Amazon...

Brand: CONFAST   |   Manufacturer: CONFAST

Package Dimensions: 3.6 x 4.7 x 6.7 inches (9.1 x 11.9 x 17.0 cm)

Amazon Price: $33.99 | as of 09/21/2019(4:33pm pst)
Availibility: Usually ships in 24 hours
List Price: $33.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #20

CONFAST 1/2" x 5-1/2" Galvanized Wedge Anchor (Box of 25)

 PartNumber: WAG12512   |   Asin: B071J271MB

Applications
The anchor is made from Carbon Steel, and is Hot-Dipped Galvanized. This anchor is designed for use in Concrete only, and should never be used in block or brick base material.

Environment
The anchor is designed for use in a Damp environment.

Hole Diameter/Bit Diameter
The anchor requires a 1/2" hole to be drilled in the base material (Concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.

Diameter of Anchor
The diameter of the anchor is 1/2".

Length Anchor
The length of the anchor is 5-1/2"

Thread Length
The length of the threads on the anchor is 4" in length.

Minimum Embedment
The minimum anchor embedment into the concrete is 2-1/4". Therefore, the anchor must be installed so that a minimum of 2-1/4" of the anchor is embedded into the concrete.

Maximum Fixture Thickness
The maximum fixture thickness or the maximum thickness of the material being fastened for a anchor is 2-3/4". This will ensure that the minimum embedment of 2-1/4" will be met.

Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 1/2" diameter anchor requires the hole in the fixture to be 5/8".

Torque Value
To be set properly in the concrete, the anchor must be torqued to between 50 - 60 ft./lbs.

Spacing between Anchors
Each anchor must be spaced a minimum distance of 5" from each other when measured center to center.

Edge Distance
It is very important not to install the anchor any closer than 2-1/2" from an unsupported edge of the concrete.

Features

  • HOT DIPPED GALVANIZED - Helps prevent rusting in moist environments
  • WIDE RANGE OF SIZES - Insures proper fastener for best results
  • PACKAGED WITH NUTS AND WASHERS - Fast, quick, complete installation
  • HOLE SIZE IS ANCHOR SIZE - Simplicity and ease of installation
  • See more on Amazon...

Brand: CONFAST   |   Manufacturer: CONFAST

Package Dimensions: 3.23 x 4.69 x 8.15 inches (8.2 x 11.9 x 20.7 cm)

Amazon Price: $46.99 | as of 09/21/2019(4:33pm pst)
Availibility: Usually ships in 24 hours
List Price: $46.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon




Looking For Something Else? Search

Most Popular
New Releases

  1. CONFAST 1/2" x 4-1/4" Wedge Anchor Zinc Plated (Box of 25)
  2. CONFAST 1/2" x 5-1/2" Wedge Anchor Zinc Plated (Box of 25)
  3. Simpson Strong Tie STB2-50334 1/2-Inch by 3-3/4-Inch Bolt Wedge Anchor for Cracked and Uncracked Con...
  4. CONFAST 1/2" x 3-3/4" Wedge Anchor Zinc Plated (Box of 25)
  5. CONFAST 3/8" x 3-3/4" Wedge Anchor Zinc Plated (Box of 50)
  6. Rotary Lift Installation install Kit -16 Wedge Anchor Bolts & 30 pack shims pack
  7. CONFAST 3/4" x 7" Wedge Anchor Zinc Plated (Box of 10)
  8. The Hillman Group 370984 Wedge Anchor, 3/8 X 3-Inch, 25-Pack
  9. CONFAST 3/4" x 10" Wedge Anchor Zinc Plated (Box of 10)
  10. (10) Galvanized Concrete Wedge Anchor Bolts 1/2 x 10 Includes Nuts & Washers

Most Wished For

  1. CONFAST 1/2" x 4-1/4" Wedge Anchor Zinc Plated (Box of 25)
  2. CONFAST 1/2" x 5-1/2" Wedge Anchor Zinc Plated (Box of 25)
  3. Simpson Strong Tie STB2-50334 1/2-Inch by 3-3/4-Inch Bolt Wedge Anchor for Cracked and Uncracked Con...
  4. CONFAST 1/2" x 3-3/4" Wedge Anchor Zinc Plated (Box of 25)
  5. CONFAST 3/8" x 3-3/4" Wedge Anchor Zinc Plated (Box of 50)
  6. Rotary Lift Installation install Kit -16 Wedge Anchor Bolts & 30 pack shims pack
  7. CONFAST 3/4" x 7" Wedge Anchor Zinc Plated (Box of 10)
  8. The Hillman Group 370984 Wedge Anchor, 3/8 X 3-Inch, 25-Pack
  9. CONFAST 3/4" x 10" Wedge Anchor Zinc Plated (Box of 10)
  10. (10) Galvanized Concrete Wedge Anchor Bolts 1/2 x 10 Includes Nuts & Washers

Most Gifted

  1. CONFAST 1/2" x 4-1/4" Wedge Anchor Zinc Plated (Box of 25)
  2. CONFAST 1/2" x 5-1/2" Wedge Anchor Zinc Plated (Box of 25)
  3. Simpson Strong Tie STB2-50334 1/2-Inch by 3-3/4-Inch Bolt Wedge Anchor for Cracked and Uncracked Con...
  4. CONFAST 1/2" x 3-3/4" Wedge Anchor Zinc Plated (Box of 25)
  5. CONFAST 3/8" x 3-3/4" Wedge Anchor Zinc Plated (Box of 50)
  6. Rotary Lift Installation install Kit -16 Wedge Anchor Bolts & 30 pack shims pack
  7. CONFAST 3/4" x 7" Wedge Anchor Zinc Plated (Box of 10)
  8. The Hillman Group 370984 Wedge Anchor, 3/8 X 3-Inch, 25-Pack
  9. CONFAST 3/4" x 10" Wedge Anchor Zinc Plated (Box of 10)
  10. (10) Galvanized Concrete Wedge Anchor Bolts 1/2 x 10 Includes Nuts & Washers

Top Selling

  1. CONFAST 1/2" x 4-1/4" Wedge Anchor Zinc Plated (Box of 25)
  2. CONFAST 1/2" x 5-1/2" Wedge Anchor Zinc Plated (Box of 25)
  3. Simpson Strong Tie STB2-50334 1/2-Inch by 3-3/4-Inch Bolt Wedge Anchor for Cracked and Uncracked Con...
  4. CONFAST 1/2" x 3-3/4" Wedge Anchor Zinc Plated (Box of 25)
  5. CONFAST 3/8" x 3-3/4" Wedge Anchor Zinc Plated (Box of 50)
  6. Rotary Lift Installation install Kit -16 Wedge Anchor Bolts & 30 pack shims pack
  7. CONFAST 3/4" x 7" Wedge Anchor Zinc Plated (Box of 10)
  8. The Hillman Group 370984 Wedge Anchor, 3/8 X 3-Inch, 25-Pack
  9. CONFAST 3/4" x 10" Wedge Anchor Zinc Plated (Box of 10)
  10. (10) Galvanized Concrete Wedge Anchor Bolts 1/2 x 10 Includes Nuts & Washers



Main Categories

Home & Garden


Home Improvement


Electronics


Office


Car & Automotive


Sporting Goods


Toys and Hobby


Health & Personal Care


Beauty Supplies


Fashion


Industrial


Related Categories

Building Materials


Materials Handling


Electrical


Hardware


Nails, Screws & Fasteners


Bathroom Fixtures


Kitchen Fixtures


Lighting


Measuring & Layout Tools


Painting Supplies & Wall Treatments


Hand Tools


Power Tool Parts & Accessories


Power Tools


Plumbing


Safety & Security


Storage & Home Organization


Welding & Soldering



We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
Certain content that appears on GistGear.com comes from Amazon services llc. This content is provided 'as is' and is subject to change or removal at any time.
Any price and availability information displayed on Amazon.com at the time of purchase will apply to the purchase of this product.
Amazon product prices and availability are accurate as of the date/time indicated and are subject to change.