Frontpage > Industrial > Industrial Electrical > Electrical Sensor Blocks

Best Electrical Sensor Blocks - Buying Guide

Last Updated: 07/18/2019

Share on


  #1

Smraza 5pcs Ultrasonic Module HC-SR04 Distance Sensor with 2pcs Mounting Bracket for Arduino UNO MEGA R3 Mega2560 Duemilanove Nano Robot XBee ZigBee S03

Model: S03k   |    Mpn: S03k   |    Ean: 0745360617986   |    PartNumber: S03k   |   Asin: B01JG09DCK

If you need more information, please contact us via email to get support.

Parameters:
1. Use voltage: DC5V
2. Quiescent current: less than 2mA
3. level output: high 5V low 0V
5. Induction angle: no more than 15 degrees
6. Detection range: 0.78~196 in/ (2cm~500cm)
7. High accuracy: up to 0.12 in/(0.3 cm)
8. Connection mode: VCC, trig (control), echo (receiving end), GND ground wire

Module working principle:
Pull the Trig pin to high level for more than 10us impulse, the module start ranging.
The module automatically sends eight 40KHz square wave to detect whether a signal is returned.
Finished ranging, If you find an object in front, Echo pin will be high level, and based on the different distance, it will take the different duration of high level.
So we can calculated the distance easily.The distance = ((Duration of high level)*(Sonic :340m/s))/2
Dimensions: 1.3 x 0.4 x 0.1 inch/3.03 x 1 x 0.25 cm (L*W*H)

Package included:
1) HC-SR04 Distance Sensor x5
2) Cartoon Mounting Bracket(Support HC-SR04 only) x2
3 Male to Female Jumper Wires x10

Smraza is a professional manufacturer on making all electronics components based on Arduino and Raspberry Pi.If you have any technical questions, please contact us by email to get support.

Features

  • Test mode :Using IO trigger for high level signal.( Not less that 10us),The Module sends eight 40 kHz automatically and detect whether there is a pulse signal back.
  • The detection zone: 0.78~196 in/ (2cm~500cm); High precision: up to 0.12 in/(0.3 cm) Effectual angle: less than 15
  • Power supply: 5V DC; Quiescent current: less than 2mA.
  • Test distance = ((Duration of high level)*(Sonic :340m/s))/2
  • Package included: 5pcs HC-SR04+ 2pcs Mounting Bracket(support HC-SR04 only)
  • See more on Amazon...

Brand: Smraza   |   Manufacturer: Smraza

Item Dimensions: 1.2 x 3.2 x 6.4 inches (3.0 x 8.1 x 16.3 cm)   |   Package Dimensions: 1.5 x 3.07 x 4.65 inches (3.8 x 7.8 x 11.8 cm)

Amazon Price: $9.59 | as of 07/18/2019(2:03pm pst)
Availibility: Usually ships in 24 hours
List Price: $9.59

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #2

HiLetgo MPU9250/6500 9-Axis 9 DOF 16 Bit Gyroscope Acceleration Magnetic Sensor 9-Axis Attitude +Gyro+Accelerator+Magnetometer Sensor Module IIC/SPI for Arduino GY-9250

Model: 3-01-0876   |    Mpn: 3-01-0876   |    PartNumber: 3-01-0876   |   Asin: B01I1J0Z7Y

Instruction
This module features the MPU-9250, which is a multi-chip module (MCM) consisting of two dies integrated into a single QFN package. One die houses the 3-Axis gyroscope and the 3-Axis accelerometer. The other die houses the AK8963 3-Axis magnetometer. Hence, the MPU-9250 is a 9-axis MotionTracking device that combines a 3-axis gyroscope, 3-axis accelerometer, 3-axis magnetometer, and a Digital Motion Processor (DMP). The MPU-9250 also features an embedded temperature sensor. This module includes pull-up resistors on the SDA, SCL, and nCS lines, pull-down resistors on the FSYNC and AD0 lines, and an on-board 3.3V voltage regulator allowing you to power the module from 5V sources such as an Arduino. If you desire to power the module from 3.3V you can bridge the solder jumper next to the voltage regulator to bypass the regulator.

Specifications:
* On-board pull-up resistors on SDA, SCL, and nCS
* On-board pull-down resistors on FSYNC and AD0
* 3-Axis Accelerometer
* Range: up to 16 g
* Sensitivity: up to 16,384 LSB/g
* 3-Axis Gyroscope
* Range: up to 2000 deg/sec
* Sensitivity: up to 131 LSB/deg/sec
* 3-Axis Magnetometer
* Range: 4800 T
* Sensitivity: 0.6 T/LSB
* Supply Voltage: 4.4 to 6.5 V or 3.3V if you solder the solder jumper near the on-board voltage regulator
* Interface: I2C
* 2C Address: 0x68 by default, 0x69 if AD0 is pulled high
* Board Dimensions: 25.5mm (1.004") long x 15.4mm (0.606") wide, 3mm (0.118") inside diameter of mounting holes
* Weight: 2.72g (0.096oz)

Package Included
1* MPU9250/6500 9-Axis 9 DOF 16 Bit Gyroscope Acceleration Magnetic Sensor
1* Ten pin male header (1x10)

Features

  • Main Chip MPU-9250
  • Power supply: 3-5V (internal low dropout regulator)
  • Communication: standard IIC communication protocol
  • Built-in 16bit AD converter, 16-bit data output
  • Using Immersion Gold PCB, machine welding process to ensure quality
  • See more on Amazon...

Brand: HiLetgo   |   Manufacturer: HiLetgo

Package Dimensions: 0.2 x 2.3 x 2.7 inches (0.5 x 5.8 x 6.9 cm)

Amazon Price: $8.49 | as of 07/18/2019(2:03pm pst)
Availibility: Usually ships in 24 hours
List Price: $8.49

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #3

0.96 Inch Yellow and Blue I2C IIC Serial 128X64 OLED Display Module for Arduino

 Ean: 0702795761080   |    PartNumber: FZ1113   |   Asin: B00O2LLT30

White color link https://www.amazon.com/dp/B00O2KDQBE
Blue color link ://www.amazon.com/dp/B00O2LKEW2
2pcs link https://www.amazon.com/dp/B01HEBIJKK

Resolution: 128X64
Color: Blue and Yellow
Viewing angle: greater than 160 degrees
Supported platforms: for arduino, 51 series, MSP430 series, STIM32 / 2, SCR chips
Low power consumption: 0.04W during normal operation
Support wide voltage: 3.3V-5V DC
Working temperature: -30-80 degrees
Volume: 27MM * 27MM * 4.1MM
Driver IC: SSD1306
Communication: IIC, only two I / O ports
No font: The software takes word modulo
Backlight: OLED self light, no backlight
Interface:
VCC: 3.3-5V
GND: Ground
SCL: Serial Clock
SDA: Serial Data

Features

  • Supported voltage: 3.3V-5V DC
  • Driver IC: SSD1306
  • Communication: IIC, only two I/O ports
  • Viewing angle: greater than 160 degrees
  • Size: 0.96 inches
  • See more on Amazon...

Brand: DIYmall   |   Manufacturer: DIYmall

Item Dimensions: 1.18 x 1.97 x 1.18 inches (3.0 x 5.0 x 3.0 cm)   |   Package Dimensions: 1.2 x 1.6 x 3.3 inches (3.0 x 4.1 x 8.4 cm)

Amazon Price: $8.99 | as of 07/18/2019(2:03pm pst)
Availibility: Usually ships in 24 hours
List Price: $8.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #4

Anmbest 5PCS LM393 Speed Detection Sensor Module, Motor Measuring Comparator, Pulse Counter Module, 5mm Slot Type IR Optocoupler, for MCU Arduino RPI

 Ean: 7653256865874   |    PartNumber: Anmbest_MD158   |   Asin: B07SNFFJJ5

Here is a motor speed sensor module, the major goal is to check the rate of an electric motor. The module can be used in association with a microcontroller for motor speed detection, pulse count, position limit, etc. In principle, any rate meter simply measures the rate at which some event occurs. Usually this is done by counting the events for a given period of time (integration interval) and then simply dividing the number of events by the time to get the rate.

Technical Specifications:
Main Chip : LM393
Working voltage 3.3 V to 5 V
Output form: digital switch output (0 and 1)
Output: Covered, output high level; Without sunscreen, the output low level
PCB size: 32 mm x 14 mm/ 1.26 0.55
Mounting Hole Size : 3mm/ 0.12"
Slotted Width : 5mm/ 0.2"
Interface::
VCC: Connect the positive 3.3v-5v power supply
GND: Connect power negative
DO: TTL switch signal output
AO: This module does not work, The module do not have Analog output
Package includes:
5 x Motor Speed Detection Sensor Module

Features

  • HIGHLIGHTS: Comparator output, clean signal, good waveform, strong driving capability, more than 15mA.
  • STRONG ANTI-INTERFERENCE:The transmissive optical sensor used consists of an infrared light emitting diode and a phototransistor. This both prevents interference from stray external light sources and by having the two components matched for a specific frequency of radiation, they are even more immune to undesired interference.
  • EASY TO USE: The DO output interface can be directly connected to the IO port of the MCU to detect whether the sensor has a occlusion. If the motor code plate is used, the motor speed can be detected. The module DO can be connected to a relay to form a limit switch, or can be connected to the active buzzer module to form an alarm.
  • EASY INSTALLATION: 3mm fixed bolt holes for easy installation.
  • WIDELY APPLICATIONS: Widely used in motor speed detection, pulse counting, position limit, etc.
  • See more on Amazon...

Brand: Anmbest   |   Manufacturer: Anmbest

Package Dimensions: 0.5 x 3.2 x 3.2 inches (1.3 x 8.1 x 8.1 cm)

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #5

Teensy++ 2.0

 Ean: 6115752053915   |    PartNumber: FBA_TEENSY++   |   Asin: B00NC4302Q

Description: The Teensy is a breadboard-friendly development board with loads of features in a, well, teensy package. The Teensy++ breaks out all of the IO available on the AT90USB1286 to breadboard-friendly 0.1" spaced headers so you can hook up a load of peripherals.

The Teensy++ comes pre-flashed with a bootloader so you can program it using the on-board USB connection: No external programmer needed! You can program the Teensy in your favorite IDE using C or you can install the Teensyduino add-on for the Arduino IDE and write Arduino sketches for Teensy!

Dimensions: 2" x 0.7" (50.8 x 17.8 mm)

Features:

8-Bit AVR Processor (AT90USB1286) 128K Flash Memory, 8K RAM, 4K EEPROM USB Can Emulate Any Type of Device Single Pushbutton Programming Arduino Compatible 8 Analog Inputs 46 Digital I/O Pins 9 PWM outputs SPI and I2C

Features

  • 8-Bit AVR Processor (AT90USB1286)
  • 128K Flash Memory, 8K RAM, 4K EEPROM
  • USB Can Emulate Any Type of Device
  • Single Pushbutton Programming
  • Arduino Compatible
  • See more on Amazon...

Brand: PJRC   |   Manufacturer: SparkFun

Package Dimensions: 0.2 x 1 x 2.5 inches (0.5 x 2.5 x 6.4 cm)

Amazon Price: $24.49 | as of 07/18/2019(2:03pm pst)
Availibility: Usually ships in 1-2 business days
List Price: $24.95

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #6

HiLetgo 3pcs 5V D1 mini Relay Shield 5V D1 mini Relay Module for WeMos D1

 PartNumber: 3-01-1220   |   Asin: B01NACU547

WeMos D1 mini Relay Shield 5V D1 mini Relay Module for WeMos D1
Description:
5V Relay Shield, use relay to control other equipment.
Features:
NO: 5A(250VAC/30VDC), 10A(125VAC), MAX:1250VA/150W
NC: 3A(250VAC/30VDC), MAX:750VA/90W
Package included:
1* WeMos D1 mini Relay Shield

Features

  • WeMos D1 mini Relay Shield 5V D1 mini Relay Module
  • WeMos D1 mini Relay Shield
  • Relay Module for WeMos D1
  • NO: 5A(250VAC/30VDC), 10A(125VAC), MAX:1250VA/150W
  • NC: 3A(250VAC/30VDC), MAX:750VA/90W
  • See more on Amazon...

Brand: HiLetgo   |   Manufacturer: HiLetgo

Package Dimensions: 1.02 x 3.35 x 5.67 inches (2.6 x 8.5 x 14.4 cm)

Amazon Price: $6.49 | as of 07/18/2019(2:03pm pst)
Availibility: Usually ships in 24 hours
List Price: $6.49

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #7

SunFounder Switch Hall Sensor Module for Arduino and Raspberry Pi

 Ean: 0701715366763   |    PartNumber: 43237-2   |   Asin: B013G5N03O

Introduction
A switch Hall sensor module that is composed by a switch Hall sensor, resistor and capacitor in an integrated circuit.
For your reference:
Based on the Hall Effect, a Hall sensor is a one that varies its output voltage in response to a magnetic field. Hall sensors can be categorized into linear (analog) Hall sensors and switch Hall sensors. A switch Hall sensor consists of voltage regulator, Hall element, differential amplifier, Schmitt trigger, and output terminal and it outputs digital values.

Application
The module can be applied to measurement of revolution, revolving speed, wind speed, flow speed, proximity switch, door lock notification device, alarm, auto-control circuit, etc.

Component List
- 1 x Switch Hall sensor module
- 1 x 3-Pin anti-reverse cable

Features

  • Signals are output as long as there is a conductor cutting the magnet field.
  • High precision and good linearity. With no contact, abrasion, shaking, or bound
  • Working voltage: 5V;PCB size: 2.0 x 2.0 cm
  • With power light and signal output indicator
  • Output digital signals, with a 3-pin anti-reverse cable included. For more information, please refer to http://wiki.sunfounder.cc/index.php?title=Hall_Sensor_module
  • See more on Amazon...

Brand: SunFounder   |   Manufacturer: SunFounder

Item Dimensions: 0.39 x 0.79 x 0.79 inches (1.0 x 2.0 x 2.0 cm)   |   Package Dimensions: 0.55 x 4.41 x 5 inches (1.4 x 11.2 x 12.7 cm)

Amazon Price: $6.99 | as of 07/18/2019(2:03pm pst)
Availibility: Usually ships in 24 hours
List Price: $6.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #8

Max485 Chip RS-485 Module TTL to RS-485 Module Raspberry Pi Pack of 5

Model: IC179   |    Mpn: IC179   |    Ean: 0701304986150   |    PartNumber: IC179   |   Asin: B00NIOLNAG

5pcs MAX485 Module RS-485 Module TTL to RS-485 Module MAX485 chip is a low power consumption for RS-485 communication, limit the slew rate transceiver.
Then 5.08 (mm) pitch 2P terminal, convenient RS-485 communication wiring.
Chip leads all pins can be controlled through the microcontroller.
Operating voltage: 5V.
Size: 44 (mm) x14 (mm).
Package included: 5pcs MAX485 Module

Features

Brand: JIUWU   |   Manufacturer: JiuWu

Package Dimensions: 0.5 x 2.9 x 3.3 inches (1.3 x 7.4 x 8.4 cm)

Amazon Price: $6.99 | as of 07/18/2019(2:03pm pst)
Availibility: Usually ships in 24 hours
List Price: $6.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #9

Adafruit 1918 Analog UV Light Sensor Breakout - GUVA-S12SD

Model: 1918   |    Mpn: 1918   |    Ean: 0720189972768   |    PartNumber: 1918   |   Asin: B00LEVTOB0

Analog UV Light Sensor Breakout - GUVA-S12SD Extend your light-sensing spectrum with this analog UV sensor module. It uses a UV photodiode, which can detect the 240-370nm range of light (which covers UVB and most of UVA spectrum). The signal level from the photodiode is very small, in the nano-ampere level, so we tossed on an Op Amp to amplify the signal to a more manageable volt-level. This sensor is much simpler than our Si1145 breakout, for it only does one thing and gives an analog voltage output instead of requiring a complicated I2C setup procedure. This makes it better for simple projects. It also has a 'true' UV sensor instead of a calibrated light-sensor. How to Use Power the sensor and op-amp by connecting V+ to 2.7-5.5VDC and GND to power ground. Then read the analog signal from the OUT pin. The output voltage is: Vo = 4.3 (*Diode-Current-in-uA.) So if the photocurrent is 1uA (9 mW/cm ), the output voltage is 4.3V. You can also convert the voltage to UV Index by dividing the output voltage by 0.1V. So if the output voltage is 0.5V, the UV Index is about 5. Please note, our UV LEDs are 400nm, outside the range of this sensor, so if you're trying to test this sensor, don't use them! A UV tanning lamp or 'lizard-lamp' will work much better. Specifications Dimensions: 10mm x 19mm x 2mm / 0.4 x 0.75 x 0.08 Weight: 0.7g Downloads & Resources Datasheet Fritzing object in Adafruit Fritzing library PCB EagleCAD files in GitHub . Made in United States.

Features

  • Product type: Sensor
  • Manufactured by Adafruit Industries
  • This product is manufactured in United States
  • See more on Amazon...

Brand: Adafruit   |   Manufacturer: Adafruit Industries

Package Dimensions: 0.1 x 2.5 x 3.2 inches (0.3 x 6.4 x 8.1 cm)

First Available: 2018-07-05

Amazon Price: $6.99 | as of 07/18/2019(2:03pm pst)
Availibility: Usually ships in 24 hours
List Price: $9.61

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #10

WINGONEER 5PCS Max 25V Voltage Detector Range 3 Terminal Sensor Module for Arduino

 Ean: 0723466639903   |    PartNumber: JT0783   |   Asin: B06XHKZCD4

WINGONEER trademark Reg.NO:4747611 Description: 100% brand new and high quality Quantity:5pc Size: 25mm 13mm/0.98"" 0.51""(approx) TThis module is based on principle of resistive voltage divider design, can make the red terminal connector input voltage to 5 times smaller.Arduino analog input voltages up to 5 v, the voltage detection module input voltage not greater than 5Vx5=25V (if using 3.3V systems, input voltage not greater than 3.3Vx5=16.5V). Arduino AVR chips have 10-bit AD, so this module simulates a resolution of 0.00489V (5V/1023), so the minimum voltage of input voltage detection module is 0.00489Vx5=0.02445V. Voltage input range : DC0-25 V Voltage detection range : DC0.02445 V-25 V Voltage analog resolution : 0.00489 V Output Interface : ""+ "" connected 5/3.3V, ""-"" connected GND, ""s"" connected Arduino AD pins DC input interface : red terminal positive with VCC, negative with GND By 3P connector, connect this module with the expansion of board Arduino, not only makes it easier for you to detect voltage battery, can also use the IICLCD1602 LCD to display voltage. Package Includes 5 x Standard Voltage Sensor Module For Robot

Features

  • Country of Manufacture: CHINA; Material: Electric Parts
  • Net Weight: 4g; Package Content: 5 x Voltage Sensor Module
  • Main Color: Blue
  • PCB Board Size: 27 x 14mm / 1.1 x 0.55(L*W)
  • Max Voltage Range: 25V
  • See more on Amazon...

Brand: WINGONEER   |   Manufacturer: WINGONEER

Package Dimensions: 0.87 x 3.62 x 4.96 inches (2.2 x 9.2 x 12.6 cm)

Amazon Price: $6.99 | as of 07/18/2019(2:03pm pst)
Availibility: Usually ships in 24 hours
List Price: $6.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #11

SunFounder 5 pcs Ultrasonic Module HC-SR04 Distance Sensor for Arduino UNO MEGA R3 Mega2560 Duemilanove Nano Robot Rapsberry Pi 3 B+, 2 & RPi Model B+ XBee ZigBee

Model: USX2   |    Mpn: SF-USX3   |    Ean: 0520141421309   |    PartNumber: SF-USX3   |   Asin: B00E0NXTJW

Introduction
The SunFounder HC-SR04 Ultrasonic Ranging module includes an ultrasonic transmitter, receiver and circuits. It has 4 pins: VCC, TRIG, ECHO and GND. The anti-reverse pin header onside makes it easy to connect and apply.
As for the ranging principle, it is quite simple to understand: pull up the pin Trig to High thus providing high level signals of at least 10us, so the module starts to detect and measure the distance; if an object is detected, the ECHO pin will be High, and the duration of it being High depends on the distance detected, thus giving the distance calculation formula: Distance = Duration of High ECHO * Speed of sound (340m/s)/2.
For more details, visit http://wiki.sunfounder.cc/index.php?title=Ultrasonic_Module

Specifications
Operating voltage: 5V
Working current: 16mA.
Weight: 90g;
Dimensions: 46 x 20.5 x 19.5 mm (thickness of anti-reverse pin socket included)

Component List
5 HC-SR04 Ultrasonic Sensors
10 Female-Male Dupont Cables
10 Female-Female Dupont Cables
1 Exquisite package box

Features

  • Ultrasonic hc-sr04 distance measuring transducer sensor, it consists of ultrasonic transmitter, receiver, and control circuit.
  • HC-SR04 Ultrasonic Sensor Distance Module: using IO trigger for at least 10us high level signal When triggered it sends out a series of 40KHz ultrasonic pulses and receives echo from an object.
  • Hc-sr04 Test Distance following formula: L = 1/2 T C ( L is the distance, T is the time between the emission and reception, and C is the sonic speed)
  • Power Supply : 5V DC; Quiescent Current : <2mA,; Effectual Angle: <15 ; Detection Distance : 2cm~450 cm; Resolution : 0.3 cm
  • Package Content: 5 HC-SR04 Ultrasonic Sensors , 10 Female-Male Dupont Cables , 10 Female-Female Dupont Cables , 1 Exquisite package box
  • See more on Amazon...

Brand: SunFounder   |   Manufacturer: SunFounder

Item Dimensions: 4.2 x 1.4 x 5 inches (10.7 x 3.6 x 12.7 cm)   |   Package Dimensions: 1.6 x 3.2 x 3.6 inches (4.1 x 8.1 x 9.1 cm)

First Available: 2018-09-13

Amazon Price: $8.78 | as of 07/18/2019(2:03pm pst)
Availibility: Usually ships in 24 hours
List Price: $10.99

Warranty: 1 Year

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #12

SunFounder DS18B20 Temperature Sensor Module for Arduino and Raspberry Pi

 Ean: 0701715366961   |    PartNumber: 2SSR   |   Asin: B013GB27HS

Introduction
Support special single-line interface; to connect DS18B20 with an MCU, only a port line is needed for the two-way communication.
With power light and signal output indicator
Output digital signals
3-Pin anti-reverse cable included

Application
The module can be applied to temperature measurement and control in devices such as freezer, barn, storage tank, telecom cabinet, electricity cabinet, cable slot, etc.
It can be used to measure the temperature in non-extreme temperature occasions, like cable trench and boiler, etc.

Component List
- 1 * DS18B20 Temperature Sensor Module
- 1 * 3-Pin anti-reverse cable

Features

  • A temperature sensor module that uses a DS18B20 Temperature Sensor. The sensor uses a 1-wire bus and outputs temperature data.
  • Directly output temperature values in Celsius
  • Temperature measurement range: -55 ~ +125 , with an inherent error of 1
  • Small-sized, low-cost hardware, strong capacity of resisting disturbance, high precision
  • Working voltage: 3.3-5V DC; PCB size: 2.0 x 2.0 cm
  • See more on Amazon...

Brand: SunFounder   |   Manufacturer: SunFounder

Item Dimensions: 0.16 x 0.79 x 0.79 inches (0.4 x 2.0 x 2.0 cm)   |   Package Dimensions: 0.79 x 3.94 x 5.2 inches (2.0 x 10.0 x 13.2 cm)

Amazon Price: $7.99 | as of 07/18/2019(2:03pm pst)
Availibility: Usually ships in 24 hours
List Price: $7.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #13

Diymore 6DOF MPU-6050 GY-521 MPU6050 3 Axis Gyroscope + Accelerometer Module for Arduino MPU 6050

Model: 8477433   |    Mpn: MPU6   |    Ean: 0611029136436   |    PartNumber: MPU6   |   Asin: B01J167T84

diymore 1PC 6DOF MPU-6050 Module 3 Axis Gyroscope + Accelerometer Module

Description:
Name: MPU-6050 module (three axis gyro + three axis acceleration)
Use chip: MPU-6050
The power supply: 3-5 v (internal low voltage difference voltage stabilizing)
Communication: standard IIC communication agreement
Chip built-in 16 bit AD converter, 16 bits of data output
The gyroscope range: + 250 500 1000 2000 /s
Acceleration range: 2 4 8 16g

Specifications:
Size:about 21*15*1.2 mm(max)
Net weight: about 3g
Color:Blue

Package Included:
1X MPU-6050 3 Axis Accelerometer Sensor

Features

  • Use chip: MPU-6050.
  • Size: 21*15*1.2 mm(max).
  • Acceleration range: 2 4 8 16g.
  • The gyroscope range: + 250 500 1000 2000 /s.
  • Communication: standard IIC communication agreement.
  • See more on Amazon...

Brand: diymore   |   Manufacturer: IP

Package Dimensions: 0.4 x 2.3 x 3 inches (1.0 x 5.8 x 7.6 cm)

Amazon Price: $4.88 | as of 07/18/2019(2:03pm pst)
Availibility: Usually ships in 24 hours
List Price: $4.88

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #14

Enerlites MPP-24 Ceiling Sensor Low Voltage Power Pack for Low Voltage Sensor and Package, Self Contained Power Supply Relay System 120~277V AC to 24V DC, White

Model: MPP-24   |    Mpn: MPP-24-STICKERED   |    Ean: 0883951412760   |    PartNumber: MPP-24-STICKERED   |   Asin: B00JAS47GG

The MPP-24 ceiling sensor power pack is the foundation for any low voltage lighting control system. The MPP-24 supplies low voltage power to occupancy sensors and other control devices, switching line voltage in response to signals from control device. The MPP-24 power pack is attached to existing junction boxes or mounted into fixture wiring trays. Features a bright LED light to indicate working operation of this power pack. Low voltage wiring should use at least 22-gauge wire. High voltage connections should use at least 14-gauge. Always check local building codes. After initial wiring is completed, check wiring diagrams to verify the power pack is wired correctly. Improper wiring can cause damage to the power pack, lighting system occupancy sensor and other control devices. This ceiling sensor power pack converts any line voltage to low voltage in various lighting control systems. The ceiling sensor power pack is designed for the MPC-50L low voltage ceiling sensor and can power up to 6 ceiling sensors per power pack. Includes a 2 year manufacturer warranty. Add Load Requirements: Ballast - 20A @ 120/277VAC Incandescent - 20A @ 120VAC Motor - 1 Horsepower @ 120/240 VAC Output - 150 mA @ 24VDC Operating Temperature - 32 to 131 F (0 to 55 C) Low Voltage Input: Control ON - 12-24VDC Hold ON - 12-24VDC Hold OFF - 12-24VDC Manual ON - 12-24VDC Relative Humidity - 20%-90% non-condensing UL Listed

Features

  • CEILING SENSOR ACCESSORIES Self contained power supply relay system for low voltage lighting control systems such as low voltage ceiling sensors and low voltage motion sensors
  • LED INDICATOR Features bright LED to indicate functioning operation of power pack
  • Connect and power up to 6 low voltage ceiling sensors with one MPP-24. Use Enerlites low voltage occupancy sensors to connect with MPP-24 ceiling sensor power pack
  • ADAPTABLE POWER PACK Convert any line voltage to low voltage 120 / 277 VA at 50/60Hz
  • EASY INSTALLATION Output of 150 mA @ 24VDC, 20A ballast / incandescent. Up to 1 horsepower at 120/240 VAC
  • See more on Amazon...

Brand: ENERLITES   |   Manufacturer: Top Greener Inc

Package Dimensions: 2.6 x 3.1 x 3.8 inches (6.6 x 7.9 x 9.7 cm)

First Available: 2017-09-14

Amazon Price: $22.99 | as of 07/18/2019(2:03pm pst)
Availibility: Usually ships in 24 hours
List Price: $22.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #15

DAOKI 5PCS 30A Range Current Sensor Module ACS712 Module for Arduino

Model: TS-US-157_5   |    Mpn: TS-US-157_5   |    Ean: 0695259097361   |    PartNumber: TS-US-157_5   |   Asin: B00XT0PL20

Features:
Chip: ACS712ELC-30A
Supply power: 5V
Measuring range: 30A
Analog output: 600 mv/A
When there is no the detection current through, the output voltage is VCC / 2
PCB board dimension:31x13mm

Package Contents:
5x30A range ACS712 current sensor module

Features

  • Details see description
  • Wholesale item !
  • Most of Modules offer only instructions and specifications.
  • Technology service NOT available.
  • See more on Amazon...

Brand: DAOKI   |   Manufacturer: DAOKI

Item Dimensions: 0.8 x 2.8 x 4.4 inches (2.0 x 7.1 x 11.2 cm)   |   Package Dimensions: 0.83 x 3.19 x 3.46 inches (2.1 x 8.1 x 8.8 cm)

Amazon Price: $10.98 | as of 07/18/2019(2:03pm pst)
Availibility: Usually ships in 24 hours
List Price: $10.98

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #16

OSOYOO 10PCS TCRT5000 Infrared Reflective IR Photoelectric Switch Barrier Line Track Sensor Module for Arduino Smart Car Robot with 5 8Pin Female to Female Jumper Wires

 PartNumber: ZZ20160126   |   Asin: B07C69N65P

Specification:
Tracking Sensor module is designed with reflected Infrared sensor, indicator light. Built in a potentiometer for sensitivity control
Product model : TCRT5000;
working Voltage : DC 3. 3-5V
Output channel : 0/1;
detect distance : 1-25mm;
focal distance : 2. 5mm
Chipset : LM393;
PCB Size : 32 x 14mm/1. 3" x 0. 55" (low)
material : electric part
Total Size : 38 x 14 x 18mm/1. 5" x 0. 55" x 0. 7"(L*w*h);
Net weight : 3g;

Package includes:
10PCS Tracking Sensor module
5PCS 8Pin female to female jumper wires

Features

  • Use for: The electricity meter pulse data sampling, Fax machine, shredder paper detection, Black and white line detection
  • Test reflection distance: 1mm to 25mm
  • With many adjustable precision potentiometer to adjust sensitivity
  • TCRT5000 sensor of infrared emission diode constantly launch infrared
  • The working voltage of 3.3V to 5V
  • See more on Amazon...

Brand: OSOYOO   |   Manufacturer: Shenzhen vership Co. LTD

Package Dimensions: 0.3 x 5 x 7 inches (0.8 x 12.7 x 17.8 cm)

Amazon Price: $11.99 | as of 07/18/2019(2:03pm pst)
Availibility: Usually ships in 24 hours
List Price: $35.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #17

PulseSensor.com the Real & Original Pulse Sensor plug-in for your project.

Model: PulseSensor_864620000204   |    Mpn: 864620000204   |    Ean: 0864620000204   |    PartNumber: 864620000204   |   Asin: B01CPP4QM0

Works with Arduino, Raspberry PI, littleBits, and more ! Plug-and-play heart-rate sensor for Arduino or DIY prototype project. It can be used by students, artists, makers, and developers who want live heart-rate data into their Arduino or RaspberrypPi projects. Project and Info: www.PulseSensor.com

Features

  • This is the Original and the Best! Accept no alternatives.
  • The Pulse Sensor Kit included everything you need for a smooth experience. This Kit Includes:
  • Soft braided-wire ribbon cable. Great for wearables! An Ear Clip that's perfectly sized to the sensor.
  • A Velcro Finger Strap, just like the pro's. Transparent Vinyl Dots, which make electrical insulation simple.
  • www.PulseSensor.com for Projects and All Info.
  • See more on Amazon...

Brand: PulseSensor.com   |   Manufacturer: World Famous Electronics

Item Dimensions: 6 x 0.5 x 4 inches (15.2 x 1.3 x 10.2 cm)   |   

Amazon Price: $19.50 | as of 07/18/2019(2:03pm pst)
Availibility: Usually ships in 24 hours
List Price: $24.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #18

Diymall Voltage Sensor Dc0-25v for Arduino with Code(Pack of 2pcs)

Model: 430   |    Mpn: FZ0430   |    Ean: 0701702805640   |    PartNumber: FZ0430   |   Asin: B00NK4L97Q

DIYmall Voltage Sensor for Arduino DC0-25V with Code(pack of 2pcs)
Description:
This module is based on a resistive divider principle design, make the interface terminal input voltage reduced 5 times, Arduino analog input voltage up to 5V, then the input voltage of the voltage detection module can not be greater than 5V 5 = 25V (if used 3.3V system, the input voltage can not exceed 3.3Vx5 = 16.5V). Because Arduino AVR chips used in 10 AD, so the resolution of the analog module is 0.00489V (5V / 1023), so the voltage detection module detects a minimum input voltage of 0.00489V 5 = 0.02445V.
Voltage input range: DC0-25V
Voltage detection range: DC0.02445V-25V
Voltage Analog Resolution: 0.00489V
DC input connector: Terminal cathode connected to VCC, GND negative pole
Output interface:
+ 5V or 3.3V
- GND
S Arduino AD pins
Package included:
2 X Voltage Sensor

Features

  • Voltage input range: DC0-25V
  • Voltage detection range: DC0.02445V-25V
  • Voltage Analog Resolution: 0.00489V
  • DC input connector: Terminal cathode connected to VCC, GND negative pole
  • Output interface: + then 5/3.3V, - then GND, s then the Arduino AD pins
  • See more on Amazon...

Brand: DIYmall   |   Manufacturer: DIYmall

Item Dimensions: 0.59 x 0.08 x 0.98 inches (1.5 x 0.2 x 2.5 cm)   |   Package Dimensions: 0.4 x 2.3 x 3 inches (1.0 x 5.8 x 7.6 cm)

Amazon Price: $5.99 | as of 07/18/2019(2:03pm pst)
Availibility: Usually ships in 24 hours
List Price: $5.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #19

Anmbest 2PCS GY-9250 MPU9250 9-Axis 9 DOF Accelerometer, Gyroscope and Magnetometer Sensor Module 16 Bit AD Converter Data Output IIC I2C SPI

 Ean: 7898822206938   |    PartNumber: Anmbest_MD41   |   Asin: B07DYR8GR4

MPU9250 is one of the most advanced combined Accelerometer, Gyroscope and Compass small size sensors currently available. They have many advanced features, including low pass filtering, motion detection, and even a programmable specialized processor.

Features:
1.Gyroscope Features
The triple-axis MEMS gyroscope in the MPU-9250 includes a wide range of features:
Digital-output X-, Y-, and Z-Axis angular rate sensors (gyroscopes) with a user-programmable fullscale range of 250, 500, 1000, and 2000 /sec and integrated 16-bit ADCs
Digitally-programmable low-pass filter
Gyroscope operating current: 3.2mA
Sleep mode current: 8 A
Factory calibrated sensitivity scale factor
Self-test
2. Accelerometer Features
The triple-axis MEMS accelerometer in MPU-9250 includes a wide range of features:
Digital-output triple-axis accelerometer with a programmable full scale range of 2g, 4g, 8g and 16g and integrated 16-bit ADCs
Accelerometer normal operating current: 450 A
Low power accelerometer mode current: 8.4 A at 0.98Hz, 19.8 A at 31.25Hz
Sleep mode current: 8 A
User-programmable interrupts
Wake-on-motion interrupt for low power operation of applications processor
Self-test
3.Magnetometer Features
The triple-axis MEMS magnetometer in MPU-9250 includes a wide range of features:
3-axis silicon monolithic Hall-effect magnetic sensor with magnetic concentrator
Wide dynamic measurement range and high resolution with lower current consumption.
Output data resolution of 14 bit (0.6 T/LSB)
Full scale measurement range is 4800 T
Magnetometer normal operating current: 280 A at 8Hz repetition rate
Self-test function with internal magnetic source to confirm magnetic sensor operation on end products
Package inlcuded:
2 X MPU9250 9-Axis 9 DOF Accelerometer, Gyroscope and Magnetometer Sensor Module
2 X 10P Pin Header

Features

  • Main Chip: MPU-9250; Power Supply: 3-5V DC(internal low dropout regulator); 400kHz Fast Mode I2C for communicating with all registers; 1MHz SPI serial interface for communicating with all registers; 20MHz SPI serial interface for reading sensor and interrupt registers; Chip built-in 16bit AD converter, 16-bit data output; Size: 15mm*25mm.
  • Gyroscope range: 250, 500, 1000, 2000 /sec; Accelerometer range: 2g, 4g, 8g, 16g; Magnetometer Full scale measurement range: 4800 T.
  • Applications: Location based services, points of interest, and dead reckoning; Handset and portable gaming; Motion-based game controllers; 3D remote controls for Internet connected DTVs and set top boxes, 3D mice; Wearable sensors for health, fitness and sports; Arduino, Raspberry Pi.
  • User-programmable digital filters for gyroscope, accelerometer, and temp sensor.
  • Internal Digital Motion Processing (DMP) engine supports advanced MotionProcessing and low power functions such as gesture recognition using programmable interrupts. Low-power pedometer functionality allows the host processor to sleep while the DMP maintains the step count.
  • See more on Amazon...

Brand: Anmbest   |   Manufacturer: Anmbest

Package Dimensions: 0.3 x 3.3 x 5.5 inches (0.8 x 8.4 x 14.0 cm)

Amazon Price: $13.99 | as of 07/18/2019(2:03pm pst)
Availibility: Usually ships in 24 hours
List Price: $29.19

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #20

HiLetgo Analog Current Meter Sensor Module AC 0~5A Ammeter Sensor Board Based on TA12-100 for Arduino

Model: 3-01-0056   |    Mpn: 3-01-0056   |    Ean: 0797698769868   |    PartNumber: 3-01-0056   |   Asin: B00HGB9RB4

Specification:
Interface: 3PIN
Power Supply: 5V
Size: 30x 24x 1.6mm
Weight: 25g

Electrical characteristics:
Transformation coefficient: 1000:1
Input current: 0--5A
Output current: 0--5mA
Sampling resistor: 200
Sampling voltage: 0--1V
Working frequency: 20-20000Hz
Working temperature: -55--85
Dielectric strength: 6KAC/1min

Package Include:
1* Analog Current Meter Sensor Module Board

If you need detail schematic, please contact us

Features

  • Analog Current Meter Module. Transformer can only sense AC
  • This electricity sensor is based on TA12-100 current transformer, which can transform AC signals of large current into small amplitude signals.
  • 3-wire electronic block interface, input 5V - GND. S pin is the output analog voltage value.
  • You can use jumpers to select the parallel output of the output to adjust the range of analog values that are output.
  • On-board 3P and 4P connecting interface for current signal output can be easily connected with your MCU development board
  • See more on Amazon...

Brand: HiLetgo   |   Manufacturer: HiLetgo

Package Dimensions: 0.79 x 2.28 x 3.74 inches (2.0 x 5.8 x 9.5 cm)

Amazon Price: $6.99 | as of 07/18/2019(2:03pm pst)
Availibility: Usually ships in 24 hours
List Price: $6.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon




Looking For Something Else? Search

Most Popular
New Releases

  1. Smraza 5pcs Ultrasonic Module HC-SR04 Distance Sensor with 2pcs Mounting Bracket for Arduino UNO MEG...
  2. HiLetgo MPU9250/6500 9-Axis 9 DOF 16 Bit Gyroscope Acceleration Magnetic Sensor 9-Axis Attitude +Gyr...
  3. 0.96 Inch Yellow and Blue I2C IIC Serial 128X64 OLED Display Module for Arduino
  4. Anmbest 5PCS LM393 Speed Detection Sensor Module, Motor Measuring Comparator, Pulse Counter Module, ...
  5. Teensy++ 2.0
  6. HiLetgo 3pcs 5V D1 mini Relay Shield 5V D1 mini Relay Module for WeMos D1
  7. SunFounder Switch Hall Sensor Module for Arduino and Raspberry Pi
  8. Max485 Chip RS-485 Module TTL to RS-485 Module Raspberry Pi Pack of 5
  9. Adafruit 1918 Analog UV Light Sensor Breakout - GUVA-S12SD
  10. WINGONEER 5PCS Max 25V Voltage Detector Range 3 Terminal Sensor Module for Arduino

Most Wished For

  1. Smraza 5pcs Ultrasonic Module HC-SR04 Distance Sensor with 2pcs Mounting Bracket for Arduino UNO MEG...
  2. HiLetgo MPU9250/6500 9-Axis 9 DOF 16 Bit Gyroscope Acceleration Magnetic Sensor 9-Axis Attitude +Gyr...
  3. 0.96 Inch Yellow and Blue I2C IIC Serial 128X64 OLED Display Module for Arduino
  4. Anmbest 5PCS LM393 Speed Detection Sensor Module, Motor Measuring Comparator, Pulse Counter Module, ...
  5. Teensy++ 2.0
  6. HiLetgo 3pcs 5V D1 mini Relay Shield 5V D1 mini Relay Module for WeMos D1
  7. SunFounder Switch Hall Sensor Module for Arduino and Raspberry Pi
  8. Max485 Chip RS-485 Module TTL to RS-485 Module Raspberry Pi Pack of 5
  9. Adafruit 1918 Analog UV Light Sensor Breakout - GUVA-S12SD
  10. WINGONEER 5PCS Max 25V Voltage Detector Range 3 Terminal Sensor Module for Arduino

Most Gifted

  1. Smraza 5pcs Ultrasonic Module HC-SR04 Distance Sensor with 2pcs Mounting Bracket for Arduino UNO MEG...
  2. HiLetgo MPU9250/6500 9-Axis 9 DOF 16 Bit Gyroscope Acceleration Magnetic Sensor 9-Axis Attitude +Gyr...
  3. 0.96 Inch Yellow and Blue I2C IIC Serial 128X64 OLED Display Module for Arduino
  4. Anmbest 5PCS LM393 Speed Detection Sensor Module, Motor Measuring Comparator, Pulse Counter Module, ...
  5. Teensy++ 2.0
  6. HiLetgo 3pcs 5V D1 mini Relay Shield 5V D1 mini Relay Module for WeMos D1
  7. SunFounder Switch Hall Sensor Module for Arduino and Raspberry Pi
  8. Max485 Chip RS-485 Module TTL to RS-485 Module Raspberry Pi Pack of 5
  9. Adafruit 1918 Analog UV Light Sensor Breakout - GUVA-S12SD
  10. WINGONEER 5PCS Max 25V Voltage Detector Range 3 Terminal Sensor Module for Arduino

Top Selling

  1. Smraza 5pcs Ultrasonic Module HC-SR04 Distance Sensor with 2pcs Mounting Bracket for Arduino UNO MEG...
  2. HiLetgo MPU9250/6500 9-Axis 9 DOF 16 Bit Gyroscope Acceleration Magnetic Sensor 9-Axis Attitude +Gyr...
  3. 0.96 Inch Yellow and Blue I2C IIC Serial 128X64 OLED Display Module for Arduino
  4. Anmbest 5PCS LM393 Speed Detection Sensor Module, Motor Measuring Comparator, Pulse Counter Module, ...
  5. Teensy++ 2.0
  6. HiLetgo 3pcs 5V D1 mini Relay Shield 5V D1 mini Relay Module for WeMos D1
  7. SunFounder Switch Hall Sensor Module for Arduino and Raspberry Pi
  8. Max485 Chip RS-485 Module TTL to RS-485 Module Raspberry Pi Pack of 5
  9. Adafruit 1918 Analog UV Light Sensor Breakout - GUVA-S12SD
  10. WINGONEER 5PCS Max 25V Voltage Detector Range 3 Terminal Sensor Module for Arduino



Main Categories

Home & Garden


Home Improvement


Electronics


Office


Car & Automotive


Sporting Goods


Toys and Hobby


Health & Personal Care


Beauty Supplies


Fashion


Industrial


Related Categories

Abrasive & Finishing


Cutting Tools


Fasteners


Filtration


Commercial Door Products


Hydraulics, Pneumatics & Plumbing


Industrial Hardware


Industrial Tools


Food Services


Janitorial & Sanitation


Lab Equipment


Material Handling


Occupational Health


Packaging & Shipping


Power Transmission


Dental Supplies


Medical Supplies


Raw Materials


Retail Fixtures & Equipment


Tapes, Adhesives & Sealants


Test, Measure & Inspect


Robotics, 3D Printing & Science Education


Industrial Electrical