Frontpage > Industrial > Industrial Electrical > Programmable Logic Circuits

Best Programmable Logic Circuits - Buying Guide

Last Updated: 04/19/2019

Share on

Bestselling Programmable Logic Circuits on Amazon

  1. RioRand USB Volt Amp Power Meter Voltage Tester Current Charging Monitor LCD Display DC (USB Blaster)
  2. XCSOURCE Pickit3 Pickit3.5 Kit3 Emulator Programmer Download Original TE239
  3. SMAKN USB Programmer CH341A Series Burner Chip 24 EEPROM BIOS LCD Writer 25 SPI Flash
  4. TERASIC TECHNOLOGIES P0082 CYCLONE IV, EP4CE22F17C6N, FPGA, DE0-NANO, DEV KIT
  5. Signstek TL866PLUS Universal USB MiniPro EEPROM Flash BIOS Programmer AVR GAL PIC SPI Support 40 Pin
  6. New PICKit3 Microchip Programmer with USB Cable, Wires Pic Kit 3 and ICSP Socket
  7. Diymore PICkit3 PIC KIT3 Debugger Programmer Emulator PIC Controller Development Board
  8. Numato Lab Mimas V2 Spartan 6 FPGA Development Board with DDR SDRAM
  9. Terasic DE10-Lite
  10. LAQIYA TL866 Plus Programmer USB EPROM Flash BIOS Programmable Logic Circuits 6 Adapters Socket Ext...

  #1

RioRand USB Volt Amp Power Meter Voltage Tester Current Charging Monitor LCD Display DC (USB Blaster)

Model: RRUSBBCPDFP   |    Mpn: RR-AU-TO   |    Ean: 0619636104336   |    PartNumber: RR-AU-TO   |   Asin: B00IRODADK

*Support 1.5V,1.8V,2.5V,3.5V and 5.0V. *Support all products : CPLD (MAX3000, MAX7000, MAX9000 and MAX II) ; FPGA (Stratix, StratixII, Cyclone, CycloneII, ACEX 1K, APEX20K and FLEX 10K) ; Active serial configuration device (EPCS1, EPCS4, EPCS16) *Support AS, PS and JTAG program (with Verify and BankCheck function) . ---- When we tested the chip above , we use the different program mode: JTAG (Cyclone Flex10K, Acex1K, Max7000 and Max3000) ; AS (EPCS1, EPCS4, EPCS16) ; PS (Stratix , Stratix GX) *Don't need a second plug operation while using AS mode ,can run the program directly after download *Support embedded logic analyzer function of SignalTapII *Support NIOS II communication and debugger -- When you use it to debug your Black Gold , it will not Pop-up warning *Faster -- about 6 times than ByteblasterII *USB interface ! -- you don't need a PC with serial port now *100% compatible with Official USB Blaster Pls note that if your components you worked with is too old and operated at +5V,it may not work with this product.

Features

  • Faster:about 6 times than ByteblasterII
  • USB interface:you don't need a PC with serial port
  • Fast download speed,stable performance
  • Support AS, PS and JTAG program ( with Verify and BankCheck function)
  • Support all ALTERA products(CPLD MAX3000 MAX7000 MAX9000 and MAXII;FPGA Stratix StratixII StratxIII Cyclone CycloneII and so on),100% compatible with Official ALTERA USB Blaster
  • See more on Amazon...

Brand: RioRand   |   Manufacturer: RioRand

Package Dimensions: 0.6 x 3 x 4.3 inches (1.5 x 7.6 x 10.9 cm)

Amazon Price: $10.99 | as of 04/19/2019(3:27pm pst)
Availibility: Usually ships in 24 hours
List Price: $10.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #2

XCSOURCE Pickit3 Pickit3.5 Kit3 Emulator Programmer Download Original TE239

Model: TE239   |    Mpn: TE239   |    Ean: 4894479396957   |    PartNumber: TE239   |   Asin: B011BBQQEK

Description:

The MPLAB PICkit 3 allows debugging and programming of PIC? and dsPIC? Flash microcontrollers at a most affordable price point using the powerful graphical user interface of the MPLAB Integrated Development Environment (IDE). The MPLAB PICkit 3 is connected to the design engineer's PC using a full speed USB interface and can be connected to the target via an Microchip debug (RJ-11) connector (compatible with MPLAB ICD 2- MPLAB ICD 3 and MPLAB REAL ICE). Support Pickit3.5 software.

Features:

The download speed- USB connection stability than ICD2.
The off-line programming functions. Development and debugging can be programmed to do product batch off-line programming.
Power output- the internal voltage can be directly in the MPLAB IDE software control.
PIKCIT3 has begun to support WIN7 system
Patch design- SMD reflow soldering processing- more stable and reliable product quality

Function:

USB (Full speed 12 Mbits/s interface to host PC)
Real-time execution
MPLAB IDE compatible (free copy included)
Built-in over-voltage/short circuit monitor
Firmware upgradeable from PC/web download
Totally enclosed
Supports low voltage to 2.0V(2.0V - 6.0V)
Diagnostic LEDs (power- busy- error)
Read/write program and data memory of microcontroller
Erase of program memory space with verification
Freeze-peripherals at breakpoint

Package included:

1 x PICKIT3
1 x T line
1 x DuPont line

Features

  • The download speed- USB connection stability than ICD2
  • The off-line programming functions. Development and debugging can be programmed to do product batch off-line programming.
  • Power output- the internal voltage can be directly in the MPLAB IDE software control.
  • PIKCIT3 has begun to support WIN7 system
  • Patch design- SMD reflow soldering processing- more stable and reliable product quality
  • See more on Amazon...

Brand: XCSOURCE   |   Manufacturer: XCSOURCE

Package Dimensions: 0.71 x 4.17 x 7.87 inches (1.8 x 10.6 x 20.0 cm)

Amazon Price: $18.99 | as of 04/19/2019(3:27pm pst)
Availibility: Usually ships in 24 hours
List Price: $18.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #3

SMAKN USB Programmer CH341A Series Burner Chip 24 EEPROM BIOS LCD Writer 25 SPI Flash

Model: TRTV1599   |    Mpn: EVB850   |    Ean: 0710185276649   |    PartNumber: EVB850   |   Asin: B013Q5P3ES

*Support 24EEROM.
*Support 25 SPI FLASH.
*Automatic identification chip model 25 series.
*Support USB to TTL.
*A multi-purpose machine, online Brush.
*STC microcontroller supports a full range of program download.
*For a variety of software for backup, erase, programming, calibration and other movements.
*Provide 5V-3.3V power supply output.
*Package include:1 x CH341A programmer .

Feedback:
We greatly appreciate your POSITIVE feedback. Please do NOT leave negative feedback without asking for help. Our aim is to provide Top Level Customer Service, so we will try our best to solve any problem.Thank you very much!

Features

  • Support 24 EEPROM and 25 SPI flash 8pin or 16pin chip.
  • Carry CH341A chip, which can recognize 25 series chip.
  • Support downloading STC series procedure of single chip.
  • Indicate 24/ 25 status with lamp.
  • Support expanding the utility by SPI pin .
  • See more on Amazon...

Brand: SMAKN   |   Manufacturer: SMAKN

Package Dimensions: 0.8 x 3.9 x 13.9 inches (2.0 x 9.9 x 35.3 cm)

Amazon Price: $10.90 | as of 04/19/2019(3:27pm pst)
Availibility: Usually ships in 24 hours
List Price: $10.90

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #4

TERASIC TECHNOLOGIES P0082 CYCLONE IV, EP4CE22F17C6N, FPGA, DE0-NANO, DEV KIT

Model: P0082-TERASIC TECHNOLOGIES   |    Mpn: P0082-TERASIC TECHNOLOGIES   |    Ean: 0013227091607   |    PartNumber: P0082-TERASIC TECHNOLOGIES   |   Asin: B00MEKRXAE

TERASIC TECHNOLOGIES P0082 CYCLONE IV, EP4CE22F17C6N, FPGA, DE0-NANO, DEV KIT

Features

  • Price For: EachOrder Unit: Tape & Reel Cut 1 Core Architecture:: FPGA Core Sub-Architecture:: Cyclone Features:: EP4CE22F17C6N FPGA, 2x GPIO Headers, 32MB RAM, Accelerometer Kit Contents:: Board, USB Cable, 2x CDs, QS Guide No. of Bits:: - SVHC:: To Be Advised Silicon Core Number:: EP4C Silicon Family Name:: Cyclone IV Silicon Manufacturer:: Altera
  • See more on Amazon...

Brand: Terasic Technologies   |   Manufacturer: TERASIC TECHNOLOGIES

Package Dimensions: 1.8 x 5.3 x 7.9 inches (4.6 x 13.5 x 20.1 cm)

Amazon Price: $79.00 | as of 04/19/2019(3:27pm pst)
Availibility: Usually ships in 24 hours
List Price: $79.00

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #5

Signstek TL866PLUS Universal USB MiniPro EEPROM Flash BIOS Programmer AVR GAL PIC SPI Support 40 Pin

 Ean: 6922302507442   |    PartNumber: US-171018-03   |   Asin: B00K73TSLM

Description
This programmer is well-designed with high-density SMD technology. An unified user interface, easy to use.
Fully functional, reliable program running of application software, ultra-small code runs faster.

Feature
*High Speed Programming Built-in MCU with high-performance and high-capacity USB interface at the communication speed of 12Mbps being in line with (For each chip) well-designed programming algorithm and USB high-speed communications.
*Unique ultra-low power: Equipped with the ultra-low power chips and power supplied via USB interface. Hardly feel the heat of the programmer after such long continuous work.
*Portable performance: Lightweight and exquisite, and no need to carry with an external power supply because of its ultra-low power that makes it more portable.
*Overvoltage, overcurrent protection: VCC, VPP power supply of the Programmer is furnished with the independent Grade 3 overcurrent protection and the protection of automatically cutting off power supply.
*Second development function of chip serial number Has a variety of automatic numbering functions that are used commonly.
*Equipped with upgrading Function of the built-in hardware firmware program that can make sure your programmer's firmware flash and application software can be timely updated.
*Programmer self-testing function: Can test itself on each pin of VPP, VCC, GND and I/O information, at the same time it can run an inside short-circuit test on VPP, VCC current.
*Superb 54/74F/LS/HC CMOS4000 series IC functional tests.
*AVR microcontroller one-to-one soft encryption
*Unified and convenient user interface.

Package:
1X USB Programmer
1xUSB Cable
1xInstallation CD

Features

  • Supports a variety of models of 51 series of microcontroller, AVR microcontroller, including ATMEGA series, ATtiny Series, AT90XXX Series MCU, MICROCHIP PIC10 PIC12 PIC16 PIC18 MCU, programming of GAL programmable logic device, SRAM test, 54/74 and CMOS4000 series IC comprehensive function tests.
  • Support a wide range of chips: All kinds of 26, 27, 28, 29, 37, 39, 49, 50 parallel ROM, EPROM, EEPROM, 24, 25, 35, 85, 93, 95 Series EEPROM, Serial parallel ROM chips, fully supporting to the 48-PIN chips of 64Mbits capacity.
  • VPP and VCC programming voltages are independently program-controlled: programmable VCC is from 3.3V to 6.5V; VPP is from 3.3V to 21V. The fluctuation of power supply is minor because of the multi-stage LC filter.
  • Automatically identify the operating system to install and run under WIN 2000/WIN XP/WIN 2003/WIN 2008/WIN VISTA/WIN7.
  • 40PIN universal pin: Don't need to move or turn around the chip when programming.
  • See more on Amazon...

Brand: Signstek   |   Manufacturer: Signstek

Package Dimensions: 2.4 x 4.3 x 4.8 inches (6.1 x 10.9 x 12.2 cm)

Amazon Price: $49.99 | as of 04/19/2019(3:27pm pst)
Availibility: Usually ships in 24 hours
List Price: $49.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #6

New PICKit3 Microchip Programmer with USB Cable, Wires Pic Kit 3 and ICSP Socket

 Ean: 0754914483434   |   Asin: B07M6WQ4B7

PICkit3 In-Circuit Debugger/Programmer Clone uses in-circuit debugging logic incorporated into each chip with Flash memory to provide a low-cost hardware debugger and programmer. Full-speed USB support using Windows standard drivers Real-time execution Processors run at maximum speeds MPLAB IDE compatible (free copy included) Built-in over-voltage/short circuit monitor Firmware upgradeable from PC/web download Totally enclosed Supports low voltage to 5 volts (1.8v to 5.0v range) Diagnostic LEDs (power, active, status) Read/write program and data memory of microcontroller Erase of all memory types (EEPROM, ID, configuration and program) with verification Freeze-peripherals at breakpoint Program up to 512K byte flash with the Programmer-to-Go

Features

  • Compatible with: CNC Milling Lathe Tool Engraving Machine
  • 1 x Pickit - 3
  • 1x USB cable
  • 1 x Ziff socket module
  • 1 x set of DuPont cable
  • See more on Amazon...

Brand: MOTOKU   |   Manufacturer: MOTOKU

Package Dimensions: 2.36 x 3.15 x 4.72 inches (6.0 x 8.0 x 12.0 cm)

Amazon Price: $18.99 | as of 04/19/2019(3:27pm pst)
Availibility: Usually ships in 1-2 business days
List Price: $18.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #7

Diymore PICkit3 PIC KIT3 Debugger Programmer Emulator PIC Controller Development Board

Model: PIC   |    Mpn: 020016   |    Ean: 0707427337312   |    PartNumber: 020016   |   Asin: B06XDMV5CP

PICKIT3 Description:
Totally enclosed.
Real-time execution.
Diagnostic LEDs (power, busy, error).
Freeze-peripherals at breakpoint.
Erase of program memory space with verification.
Read/write program and data memory of microcontrolle.r
Program up to 512K byte flash with the Programmer-to-Go.

The MPLAB PICkit 3 allows debugging and programming of PIC and dsPIC Flash microcontrollers at a most affordable price point using the powerful graphical user interface of the MPLAB Integrated Development Environment (IDE).
The MPLAB PICkit 3 is connected to the design engineer's PC using a full speed USB interface and can be connected to the target via an Microchip debug (RJ-11) connector (compatible with MPLAB ICD 2, MPLAB ICD 3 and MPLAB REAL ICE).

Programmer Seat Description:
Installing the microcontroller, 28-pin, 40-pin microcontroller left aligned 28/40P (A) This flag line short-circuit cap on the A position.
The 8,14,18,20-pin microcontroller aligned on the left 8P/14P/18P/20P flag line (B), shorting cap on the B position.
The ICD2, KIT2, KIT3 crystal head or 6Pin Block programming connection for programming the programming operation. (Note: a separate program of the seat can not be programmed the chip is programmed functions).

The seat supports the following programming microcontroller:
PIC16/18XX 40PIN Series devices (except 16F59)
PIC16/18XX 28PIN Series devices (except 16F57)
PIC16/18XX 18PIN Series devices
The PIC 8PIN/14PIN/20PIN family of devices (except 10FXX)

Note: If the item you order from diymore is not working, we support 100% refund. Take it easy.

Package Included:
1 X PICKIT3 Simulator
1 X USB Cable
1 X 6-Pin cable

Features

  • Built-in over-voltage/short circuit monitor.
  • MPLAB IDE compatible (free copy included).
  • Firmware upgradeable from PC/web download.
  • USB (Full speed 12 Mbits/s interface to host PC).
  • Supports low voltage to 2.0 volts (2.0v to 6.0v range).
  • See more on Amazon...

Brand: diymore   |   Manufacturer: IP

Package Dimensions: 1.02 x 5.55 x 6.89 inches (2.6 x 14.1 x 17.5 cm)

Amazon Price: $18.50 | as of 04/19/2019(3:27pm pst)
Availibility: Usually ships in 24 hours
List Price: $18.50

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #8

Numato Lab Mimas V2 Spartan 6 FPGA Development Board with DDR SDRAM

 PartNumber: MIMASV2   |   Asin: B00RL7FCQW

MIMAS V2 is a feature packed yet low cost FPGA Development board featuring Xilinx Spartan-6 FPGA. MIMAS V2 is specially designed for experimenting and learning system design with FPGAs. This development board features SPARTAN XC6SLX9 CSG324 FPGA with onboard 512Bb DDR SDRAM. The USB 2.0 interface provides fast and easy configuration download to the on-board SPI flash. No need to buy an expensive programmer or special downloader cable to download the bit stream to the board.

Features

  • FPGA: Spartan XC6SLX9 in CSG324 package
  • DDR Memory: 166MHz 512Mb LPDDR (MT46H32M16LF/W949D6CBHX6E)
  • Flash memory: 16 Mb SPI flash memory (M25P16)
  • USB 2.0 interface for On-board flash programming
  • https://numato.com/docs/mimas-v2-spartan-6-fpga-development-board-with-ddr-sdram/
  • See more on Amazon...

Brand: NUMATO LAB   |   Manufacturer: NUMATO SYSTEMS PRIVATE LIMITED

Amazon Price: $69.95 | as of 04/19/2019(3:27pm pst)
Availibility: Usually ships in 1-2 business days
List Price: $69.95

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #9

LAQIYA TL866 Plus Programmer USB EPROM Flash BIOS Programmable Logic Circuits 6 Adapters Socket Extractor for 15000 IC

 Ean: 0790996939926   |    PartNumber: 43237-2   |   Asin: B07CDD9PGT

www.autoelectric.cn/MiniPro/TL866II_Instructions.pdf
Latest software download link: www.autoelectric.cn/MiniPro/XgproV705_Setup.rar
Support Device List: www.autoelectric.cn/MiniPro/TL866II_List.txt (please note: before buying, make sure the models you want to program are in the list!)

Tl866II PLUS programmer is the improvement of TL866CS/A programmer, difference is much higher programming speed (up to 2x) of high-capacity memories. It supports multiprogramming mode (up to four ). Well-designed cheap professional programmer, Production of high-density SMD technology, a unified user interface, easy to use, fully functional, reliable program running of application software, ultr-small code -runs faster, supports bilingual (English and Chinese), it can automatically identify the operating system to install and run under WIN 2000/WIN XP/WIN 2003/WIN 2008/WIN VISTA /WIN7/WIN8/WIN10 (32BIit/64Bit).

TL866II Plus VS Old Version
Description ***************TL866II Plus********* TL866A ***********TL866CS
Pin Dectected ************YES *******************No *****************No
1.8V supported ***********YES *******************No *****************No
NAND FLASH *************YES ******************No *****************No
ISP for 24/93/25 MCU *****YES *************only MCU *************No
VPP Max.Voltage ********18V *******************21V ***************21V
VCC Voltage ************1.8V-6.5V ************3.3V-6.5V *********3.3V-6.5

Package Included:
1. SOP8--DIP8 Adapter
2. PLCC44--DIP40 Adapter
3. PLCC32--DIP32 Adapter
4 PLCC28--DIP24 Adapter
5. PLCC20--DIP20 Adapter
6. OP16/SOP8/MSOP8/TSSOP8/SSOP8 adapter
7. PLCC IC Extractor
8. ICSP cable
9. USB 2.0 12Mbps Interface cable
10. TL866II Plus Programmer

Features

  • Wide range of chip 15000+ support, support for serial and parallel series 40/44/48PIN large capacity FLASH
  • Unique serial ICSP interface. supporting the serial download and high-speed parallel high voltage programming
  • Best internal 40 pin over voltage protection, the strongest VCC/VPP 4-level overcurrent protection. The short-circuit do not reset the PC
  • Original chip encryptionoperation on AVR microcontroller with internal RC Calibration byte. The Decrypt software can not be directly run on another same type of chip
  • Support simultaneously burn with 4 Programmers each computer
  • See more on Amazon...

Brand: Laqiya   |   Manufacturer: Laqiya

Package Dimensions: 2.5 x 4.2 x 6 inches (6.4 x 10.7 x 15.2 cm)

Amazon Price: $59.99 | as of 04/19/2019(3:27pm pst)
Availibility: Usually ships in 24 hours
List Price: $59.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #10

Major Brands 28C256-15 ICS and Semiconductors, 150 Nanoseconds, DIP-28, 32K x 8, EPROM, 5V

Model: 28C256-15   |    Mpn: 28C256-15   |    PartNumber: 28C256-15   |   Asin: B00B885ZZI

The product type is Major Brands 28C256-15 ICs and Semiconductors, 150 Nanoseconds, DIP-28, 32K x 8, EPROM, 5V. Made in United States and manufactured by Major Brands.

Features

Brand: MAJOR BRANDS   |   Manufacturer: Major Brands

Package Dimensions: 0.39 x 1.18 x 3.39 inches (1.0 x 3.0 x 8.6 cm)

First Available: 2017-11-25

Amazon Price: $5.49 | as of 04/19/2019(3:27pm pst)
Availibility: Usually ships in 24 hours
List Price: $5.49

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #11

ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32

Model: ST-LINK/V2   |    Mpn: ST-LINK/V2   |    Ean: 0717520032137   |    PartNumber: ST-LINK/V2   |   Asin: B00SDTEM1I

The ST-LINK/V2 is an in-circuit debugger and programmer for the STM8 and STM32 microcontroller families. The single wire interface module (SWIM) and JTAG/serial wire debugging (SWD) interfaces are used to communicate with any STM8 or STM32 microcontroller located on an application board. STM8 applications use the USB full-speed interface to communicate with the ST Visual Develop (STVD) or ST Visual Program (STVP) software. STM32 applications use the USB full-speed interface to communicate with Atollic , IARTM, Keil or TASKING integrated development environments. Key Features
5 V power supplied by a USB connector
USB 2.0 full-speed-compatible interface
USB standard A to Mini- B cable
SWIM specific features: 1.65 V to 5.5 V application voltage supported on SWIM interface - SWIM low-speed and high-speed modes supported - SWIM programming speed rate: 9.7 Kbytes/s in low speed and 12.8 Kbytes/s in high speed - SWIM cable for connection to the application via an ERNI standard vertical connector (ref: 284697 or 214017) or horizontal connector (ref: 214012) - SWIM cable for connection to the application via a pin header or a 2.54 mm pitch connector
JTAG/serial wire debugging (SWD) specific features: 1.65 V to 3.6 V application voltage supported on the JTAG/SWD interface and 5 V tolerant inputs - JTAG cable for connection to a standard JTAG 20-pin pitch 2.54 mm connector - JTAG supported - SWD and serial wire viewer (SWV) communication supported
Direct firmware update feature supported (DFU)
Status LED which blinks during communication with the PC
Operating temperature 0 to 50 C

Features

  • The ST-LINK/V2 is an in-circuit debugger and programmer for the STM8 and STM32 microcontroller families
  • The single wire interface module (SWIM) and JTAG/serial wire debugging (SWD) interfaces are used to communicate with any STM8 or STM32 microcontroller located on an application board
  • STM8 applications use the USB full-speed interface to communicate with the ST Visual Develop (STVD) or ST Visual Program (STVP) software.
  • STM32 applications use the USB full-speed interface to communicate with Atollic , IARTM, Keil or TASKING integrated development environments.
  • 5 V power supplied by a USB connector
  • See more on Amazon...

Brand: STMicroelectronics   |   Manufacturer: STMicroelectronics

Item Dimensions: 1 x 3 x 4 inches (2.5 x 7.6 x 10.2 cm)   |   Package Dimensions: 1.18 x 4.25 x 6.14 inches (3.0 x 10.8 x 15.6 cm)

Amazon Price: $28.07 | as of 04/19/2019(3:27pm pst)
Availibility: Usually ships in 2-3 business days
List Price: $28.07

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #12

Digilent JTAG-HS3 Programming Cable

Model: 210-299   |    Mpn: 210-299   |    Ean: 4250798400193   |    PartNumber: 210-299   |   Asin: B0725Z7Q12

The JTAG-HS3 is the newest member of our family of affordable high-speed Xilinx FPGA programming solutions. The HS3 builds on the successful JTAG-HS1 by adding an open-drain buffer to pin 14 allowing for the debugging of Xilinx Zynq-SOC processors. It can be attached to target boards using Xilinx's 2x7 connector*, and is compatible with all Xilinx tools, including iMPACT, ChipScope, and EDK. When connected to a PC via a standard A to micro-USB cable, the JTAG HS3 receives its power from USB and can be recognized as a Digilent programming cable, even if the HS3 is not attached to the target board. The JTAG bus can be shared with other devices as the HS3's signals are held in high-impedance, except when actively driven during programming. The HS3 is small and light, allowing it to be held firmly in place by the system board connector. * This is a unique programming header and is not compatible with the 1x6 MTE Digilent JTAG Connector.

Features

  • Small, complete, all-in-one JTAG programming/debugging solution for Xilinx FPGAs and SoCs
  • Plugs directly into standard Xilinx JTAG header
  • High-Speed USB2 port that can drive JTAG bus up to 30Mbit/sec (frequency adjustable by user)
  • Open drain buffer on pin 14 allows debugging software to reset the processor core of
  • Uses USB Micro-B connector
  • See more on Amazon...

Brand: Digilent   |   Manufacturer: Digilent

Item Dimensions: 0.5 x 5 x 3 inches (1.3 x 12.7 x 7.6 cm)   |   Package Dimensions: 0.5 x 3 x 5 inches (1.3 x 7.6 x 12.7 cm)

Amazon Price: $59.00 | as of 04/19/2019(3:27pm pst)
Availibility: Usually ships in 2-3 business days
List Price: $59.00

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #13

Original PICkit3 by Microchip : MPLAB PICkit 3 PIC In-Circuit Debugger Programmer @XYGStudy

Model: LYSB00DYQII92-ELECTRNCS   |    Mpn: LYSB00DYQII92-ELECTRNCS   |    Ean: 0519997278144   |    PartNumber: LYSB00DYQII92-ELECTRNCS   |   Asin: B00DYQII92

Description Microchip's PICkit3 In-Circuit Debugger/Programmer uses in-circuit debugging logic incorporated into each chip with Flash memory to provide a low-cost hardware debugger and programmer. The MPLAB PICkit3 allows debugging and programming of PIC and dsPIC Flash microcontrollers at a most affordable price point using the powerful graphical user interface of the MPLAB Integrated Development Environment (IDE). The MPLAB PICkit3 is connected to the design engineer's PC using a full speed USB interface and can be connected to the target via an Microchip debug (RJ-11) connector (compatible with MPLAB ICD 2, MPLAB ICD 3 and MPLAB REAL ICE). The connector uses two device I/O pins and the reset line to implement in-circuit debugging and In-Circuit Serial Programming. Features Full-speed USB support using Windows standard drivers Real-time execution Processors run at maximum speeds MPLAB IDE compatible (free copy included) Built-in over-voltage/short circuit monitor Firmware upgradeable from PC/web download Totally enclosed Supports low voltage to 5 volts (1.8v to 5.0v range) Diagnostic LEDs (power, active, status) Read/write program and data memory of microcontroller Erase of all memory types (EEPROM, ID, configuration and program) with verification Freeze-peripherals at breakpoint Program up to 512K byte flash with the Programmer-to-Go Package Contains PICkit3 1 USB type A to Mini-B cable 1 6-pin RJ11 cable 1 RJ-11 to ICSP adaptor 1 6-pin ICSP cable 1 For more details you may need to know, pls firstly send me message via Amazon,
I will then send attached link including User Guide for you, thank you for patience.:)


Features

  • Original PICkit3 Microchip MPLAB PICkit 3 PIC In-Circuit Debugger Programmer
  • PICkit3 In-Circuit Debugger, Programmer-To-Go function
  • Full-speed USB support using Windows standard drivers
  • Real-time execution, Processors run at maximum speeds
  • MPLAB IDE compatible (free copy included), Firmware upgradeable from PC/web download
  • See more on Amazon...

Brand: XYG-PIC   |   Manufacturer: Microchip

Item Dimensions: 0.8 x 5.3 x 7.9 inches (2.0 x 13.5 x 20.1 cm)   |   Package Dimensions: 2.5 x 7.2 x 9.2 inches (6.4 x 18.3 x 23.4 cm)

Amazon Price: $74.49 | as of 04/19/2019(3:27pm pst)
Availibility: Usually ships in 24 hours
List Price: $74.49 | Used Price: $65.95

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #14

Texas Instruments SN74LS86AN ICS and Semiconductors, XOR Gate, 4 Element, 2 Input Bipolar, 14-Pin, Plastic DIP Tube, 19.3 mm L x 6.35 mm W x 4.57 mm H (Pack of 10)

Model: SN74LS86AN   |    Mpn: SN74LS86AN   |    Ean: 2050000056048   |    PartNumber: SN74LS86AN   |   Asin: B005T7J14A

These devices contain four independent 2-input exclusive-or Gates. A common application is as a true/complement element. If one of the inputs is low, the other input will be reproduced in true form at the output. If one of the inputs is high, the signal on the other input will be reproduced inverted at the output.

Features

  • Fabrication technology - bipolar
  • Screening level - commercial
  • Propagation delay test condition - 15Pf
  • See more on Amazon...

Brand: Texas Instruments   |   Manufacturer: Texas Instruments

Package Dimensions: 0.51 x 0.51 x 7.01 inches (1.3 x 1.3 x 17.8 cm)

First Available: 2017-03-12

Amazon Price: $5.50 | as of 04/19/2019(3:27pm pst)
Availibility: Usually ships in 24 hours
List Price: $5.50

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #15

Texas Instruments SN74LS47N ICS and Semiconductors, Single Decoder/Driver, 4-to-7, 16 Pin, Plastic Dip Tube, 4.57 mm H x 6.35 mm W x 19.3 mm L (Pack of 3)

Model: SN74LS47N   |    Mpn: SN74LS47N   |    PartNumber: SN74LS47N   |   Asin: B00CHTL2TK

The product type is Texas Instruments SN74LS47N ICs and Semiconductors, Single Decoder/Driver, 4-to-7, 16 Pin, Plastic Dip Tube, 4.57 mm H x 6.35 mm W x 19.3 mm L. Made in Taiwan and manufactured by Texas Instruments.

Features

  • Open-collector outputs drive indicators directly
  • Lamp-test provision
  • Leading/trailing zero suppression
  • See more on Amazon...

Brand: Texas Instruments   |   Manufacturer: Texas Instruments

Package Dimensions: 1.1 x 1.7 x 4.2 inches (2.8 x 4.3 x 10.7 cm)

Amazon Price: $5.90 | as of 04/19/2019(3:27pm pst)
Availibility:
List Price:

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #16

TOOGOO(R) 5pcs LOT CD74HC4067 16-Channel Digital Multiplexer Breakout Board Module For Arduino

Model: 127262   |    Mpn: GOMUKASINSUD14553   |    Ean: 0192090140244   |    PartNumber: GOMUKASINSUD14553   |   Asin: B0762FGN6J

* SODIAL is a registered trademark. ONLY Authorized seller of SODIAL can sell under SODIAL listings.Our products will enhance your experience to unparalleled inspiration. SODIAL(R) 5pcs LOT CD74HC4067 16-Channel Digital Multiplexer Breakout Board Module For Arduino To control it, connect 4 digital outputs to the chip's address select pins (S0-S3), and send it the binary address of the channel you want (see the datasheet for details). This allows you to connect up to 16 sensors to your system using only 5 pins! Since the mux/demux also works with digital signals, you can use it to pipe TTL-level serial data to or from multiple devices. For example, you could use it to connect the TX pins of 16 devices to one RX pin on your microcontroller. You can then select any one of those 16 devices to listen to. If you want two-way communications, you can add a second board to route your microcontroller's TX line to 16 device's RX lines. By using multiple boards, you can create similar arrangements for I2C, SPI, etc. The internal switches are bidirectional, support voltages between ground and VCC, have low "on" resistance and low "off" leakage, and to prevent crosstalk, perform "break-before-make" switching. The board also breaks out the chip's "enable" pin, which when driven high, will completely disconnect the common pin (all switches "off"). 2V to 6V operation "On" resistance: 70 Ohms @ 4.5V 6ns break-before-make @ 4.5V Wide operating temperature range: -55 Degrees Celsius to 125 Degrees Celsius size:2*1.2cm/0.79*0.47 inch material:Metal colour:blue packing:5*Breakout Board Module Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.

Features

  • Function: Use 16 ADCs to collect 16 analog signals.
  • Use the CD74HC4067 16-channel analog signal switch;Analog signal input: C0-C15 16 channels.
  • Analog output: DIG;Channel control: S0-S3
  • This is a breakout board for the very handy 16-Channel Analog/Digital Multiplexer/Demultiplexer CD74HC4067.
  • This chip is like a rotary switch - it internally routes the common pin (COM in the schematic, SIG on the board) to one of 16 channel pins (CHANxx). It works with both digital and analog signals (the voltage can't be higher than VCC), and the connections function in either direction.
  • See more on Amazon...

Brand: SODIAL(R)   |   Manufacturer: SODIAL(R)

Amazon Price: $3.35 | as of 04/19/2019(3:27pm pst)
Availibility: Usually ships in 1-2 business days
List Price: $3.35

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #17

SUPERELE PIC PICKit 3 PICKit3 programer PIC Kit3 PIC Simulator

 Ean: 6931547079454   |   Asin: B01N3C3VS0

Self-Made Feature:
1, HID interface, say no more driver again.
2, Support windows 7 system.

PICkit 3 Features:
USB (Full speed 12 Mbits/s interface to host PC)
Real-time execution
MPLAB IDE compatible (copy included)
Built-in over-voltage/short circuit monitor
Firmware upgradeable from PC/web download
Totally enclosed
Supports low voltage to 2.0 volts (2.0v to 6.0v range)
Diagnostic LEDs (power, busy, error)
Read/write program and data memory of microcontroller
Erase of program memory space with verification
Freeze-peripherals at breakpoint
Program up to 512K byte flash with the Programmer-to-Go
The MPLAB PICkit 3 allows debugging and programming of PIC and dsPIC Flash microcontrollers at a most affordable price point using the powerful graphical user interface of the MPLAB Integrated Development Environment (IDE). The MPLAB PICkit 3 is connected to the design engineer's PC using a full speed USB interface and can be connected to the target via an Microchip debug (RJ-11) connector (compatible with MPLAB ICD 2, MPLAB ICD 3 and MPLAB REAL ICE).

Pakcage List:
1 PICKIT3
1 USB cable
1 6pin cable

Features

  • USB (Full speed 12 Mbits/s interface to host PC)
  • Real-time execution
  • MPLAB IDE compatible (copy included)
  • Built-in over-voltage/short circuit monitor
  • Firmware upgradeable from PC/web download
  • See more on Amazon...

Brand: SUPERELE   |   Manufacturer: SUPERELE

Package Dimensions: 0.87 x 2.95 x 4.76 inches (2.2 x 7.5 x 12.1 cm)

Amazon Price: $17.75 | as of 04/19/2019(3:27pm pst)
Availibility: Usually ships in 24 hours
List Price: $17.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #18

Numato Lab Elbert V2 - Spartan 3A FPGA Development Board

 PartNumber: FPGAX006   |   Asin: B00N0SED34

ELBERT V2 is a simple but versatile FPGA Learning/Development board featuring Xilinx Spartan 3A FPGA. An excellent choice for beginners and advance learners for experimenting and learning system design with FPGAs. This development board features Xilinx XC3S50A 144 pin FPGA with maximum 108 user IOs (Some IOs are dedicated for system and peripherals). USB 2 interface provides fast and easy configuration download to the on board SPI flash. You don't need a programmer or special downloader cable to download bit stream to Elbert. ELBERT V2 features a stable clock source which is derived from on board configuration controller. ELBERT V2 incorporates LEDs, switches and other peripherals for curious users to get started with "Hello World" program in a matter of minutes. Board features - FPGA: Spartan XC3S50A in TQG144 package - Flash memory: 16 Mb SPI flash memory (M25P16) - USB 2.0 interface for On-board flash programming - FPGA configuration via JTAG and USB - 8 LEDs ,Six Push Buttons and 8 way DIP switch for user defined application - VGA output - Stereo audio out - Micro SD Card Adapter - Three Seven Segment Displays - 39 IOs for user defined purposes - On-board voltage regulators for single power rail operation - ROHS Compliant

Features

  • FPGA: Spartan XC3S50A in TQG144 package
  • Flash memory: 16 Mb SPI flash memory (M25P16)
  • USB 2.0 interface for On-board flash programming
  • https://numato.com/product/elbert-v2-spartan-3a-fpga-development-board
  • https://numato.com/docs/elbert-v2-spartan-3a-fpga-development-board/
  • See more on Amazon...

Brand: NUMATO LAB   |   Manufacturer: NUMATO SYSTEMS PRIVATE LIMITED

Package Dimensions: 1.1 x 4.3 x 5.7 inches (2.8 x 10.9 x 14.5 cm)

Amazon Price: $49.95 | as of 04/19/2019(3:27pm pst)
Availibility: Usually ships in 24 hours
List Price: $49.95

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon




Looking For Something Else? Search

Most Popular
New Releases

  1. RioRand USB Volt Amp Power Meter Voltage Tester Current Charging Monitor LCD Display DC (USB Blaster...
  2. XCSOURCE Pickit3 Pickit3.5 Kit3 Emulator Programmer Download Original TE239
  3. SMAKN USB Programmer CH341A Series Burner Chip 24 EEPROM BIOS LCD Writer 25 SPI Flash
  4. TERASIC TECHNOLOGIES P0082 CYCLONE IV, EP4CE22F17C6N, FPGA, DE0-NANO, DEV KIT
  5. Signstek TL866PLUS Universal USB MiniPro EEPROM Flash BIOS Programmer AVR GAL PIC SPI Support 40 Pin
  6. New PICKit3 Microchip Programmer with USB Cable, Wires Pic Kit 3 and ICSP Socket
  7. Diymore PICkit3 PIC KIT3 Debugger Programmer Emulator PIC Controller Development Board
  8. Numato Lab Mimas V2 Spartan 6 FPGA Development Board with DDR SDRAM
  9. LAQIYA TL866Ⅱ Plus Programmer USB EPROM Flash BIOS Programmable Logic Circuits 6 Adapters Socket Ext...

Most Wished For

  1. RioRand USB Volt Amp Power Meter Voltage Tester Current Charging Monitor LCD Display DC (USB Blaster...
  2. XCSOURCE Pickit3 Pickit3.5 Kit3 Emulator Programmer Download Original TE239
  3. SMAKN USB Programmer CH341A Series Burner Chip 24 EEPROM BIOS LCD Writer 25 SPI Flash
  4. TERASIC TECHNOLOGIES P0082 CYCLONE IV, EP4CE22F17C6N, FPGA, DE0-NANO, DEV KIT
  5. Signstek TL866PLUS Universal USB MiniPro EEPROM Flash BIOS Programmer AVR GAL PIC SPI Support 40 Pin
  6. New PICKit3 Microchip Programmer with USB Cable, Wires Pic Kit 3 and ICSP Socket
  7. Diymore PICkit3 PIC KIT3 Debugger Programmer Emulator PIC Controller Development Board
  8. Numato Lab Mimas V2 Spartan 6 FPGA Development Board with DDR SDRAM
  9. LAQIYA TL866Ⅱ Plus Programmer USB EPROM Flash BIOS Programmable Logic Circuits 6 Adapters Socket Ext...

Most Gifted

  1. RioRand USB Volt Amp Power Meter Voltage Tester Current Charging Monitor LCD Display DC (USB Blaster...
  2. XCSOURCE Pickit3 Pickit3.5 Kit3 Emulator Programmer Download Original TE239
  3. SMAKN USB Programmer CH341A Series Burner Chip 24 EEPROM BIOS LCD Writer 25 SPI Flash
  4. TERASIC TECHNOLOGIES P0082 CYCLONE IV, EP4CE22F17C6N, FPGA, DE0-NANO, DEV KIT
  5. Signstek TL866PLUS Universal USB MiniPro EEPROM Flash BIOS Programmer AVR GAL PIC SPI Support 40 Pin
  6. New PICKit3 Microchip Programmer with USB Cable, Wires Pic Kit 3 and ICSP Socket
  7. Diymore PICkit3 PIC KIT3 Debugger Programmer Emulator PIC Controller Development Board
  8. Numato Lab Mimas V2 Spartan 6 FPGA Development Board with DDR SDRAM
  9. LAQIYA TL866Ⅱ Plus Programmer USB EPROM Flash BIOS Programmable Logic Circuits 6 Adapters Socket Ext...

Top Selling

  1. RioRand USB Volt Amp Power Meter Voltage Tester Current Charging Monitor LCD Display DC (USB Blaster...
  2. XCSOURCE Pickit3 Pickit3.5 Kit3 Emulator Programmer Download Original TE239
  3. SMAKN USB Programmer CH341A Series Burner Chip 24 EEPROM BIOS LCD Writer 25 SPI Flash
  4. TERASIC TECHNOLOGIES P0082 CYCLONE IV, EP4CE22F17C6N, FPGA, DE0-NANO, DEV KIT
  5. Signstek TL866PLUS Universal USB MiniPro EEPROM Flash BIOS Programmer AVR GAL PIC SPI Support 40 Pin
  6. New PICKit3 Microchip Programmer with USB Cable, Wires Pic Kit 3 and ICSP Socket
  7. Diymore PICkit3 PIC KIT3 Debugger Programmer Emulator PIC Controller Development Board
  8. Numato Lab Mimas V2 Spartan 6 FPGA Development Board with DDR SDRAM
  9. LAQIYA TL866Ⅱ Plus Programmer USB EPROM Flash BIOS Programmable Logic Circuits 6 Adapters Socket Ext...



Main Categories

Home & Garden


Home Improvement


Electronics


Office


Car & Automotive


Sporting Goods


Toys and Hobby


Health & Personal Care


Beauty Supplies


Fashion


Industrial


Related Categories

Abrasive & Finishing


Cutting Tools


Fasteners


Filtration


Commercial Door Products


Hydraulics, Pneumatics & Plumbing


Industrial Hardware


Industrial Tools


Food Services


Janitorial & Sanitation


Lab Equipment


Material Handling


Occupational Health


Packaging & Shipping


Power Transmission


Dental Supplies


Medical Supplies


Raw Materials


Retail Fixtures & Equipment


Tapes, Adhesives & Sealants


Test, Measure & Inspect


Robotics, 3D Printing & Science Education


Industrial Electrical



We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
Certain content that appears on GistGear.com comes from Amazon services llc. This content is provided 'as is' and is subject to change or removal at any time.
Any price and availability information displayed on Amazon.com at the time of purchase will apply to the purchase of this product.
Amazon product prices and availability are accurate as of the date/time indicated and are subject to change.