Frontpage > Industrial > Industrial Hardware > Continuous & Piano Hinges

Best Continuous & Piano Hinges - Buying Guide

Last Updated: 04/20/2019

Share on

Bestselling Continuous & Piano Hinges on Amazon

  1. Stainless Steel 304 Continuous Hinge with Hole, Bright Annealed Finish, 0.04" Leaf Thickness, 1-1/2"...
  2. National Hardware N265-371 V570 Continuous Hinge in Nickel
  3. Stainless Steel 304 Continuous Hinge with Hole, Bright Annealed Finish, 0.04" Leaf Thickness, 2" Ope...
  4. Stainless Steel 304 Continuous Hinge with Hole, Bright Annealed Finish, 0.04" Leaf Thickness, 2" Ope...
  5. Stainless Steel 304 Continuous Hinge with Holes, Unfinished, 0.06" Leaf Thickness, 2" Open Width, 1/...
  6. Steel Plain Continuous Hinge with Holes, Unfinished, 0.06" Leaf Thickness, 3" Open Width, 1/8" Pin D...
  7. Stainless Steel 304 Continuous Hinge with Holes, Unfinished, 0.042" Leaf Thickness, 2" Open Width, 3...
  8. Stainless Steel 304 Continuous Hinge with Hole, Bright Annealed Finish, 0.04" Leaf Thickness, 2" Ope...
  9. Stainless Steel 304 Continuous Hinge with Holes, Unfinished, 0.06" Leaf Thickness, 2" Open Width, 1/...
  10. Aluminum 3003 Continuous Hinge with Holes, Unfinished, 0.06" Leaf Thickness, 2" Open Width, 1/8" Pin...

  #1

Stainless Steel 304 Continuous Hinge with Hole, Bright Annealed Finish, 0.04" Leaf Thickness, 1-1/2" Open Width, 5/64" Pin Diameter, 1/2" Knuckle Length, 3' Long (Pack of 1)

Model: BA1003X36   |    Mpn: BA1003X36   |    PartNumber: BA1003X36   |   Asin: B007HBNMTG

The stainless steel 304 continuous hinge has countersunk holes and is suitable for surface-mounted applications requiring uninterrupted support along the full length of the pieces being joined, such as appliance doors, industrial kitchen equipment, and metal storage cabinets. Stainless steel 304 resists corrosion up to 1,500 degrees F and is suitable for applications used in corrosive environments, though not as resistant to corrosion as stainless steel 316. A weldable material, stainless steel 304 is stronger than steel and aluminum. The bright annealed finish gives this hinge a mirrorlike appearance and offers additional protection against corrosion. This finished hinge is suited for applications such as cabinetry and piano lids where a polished hinge (as opposed to a flat finished or unfinished hinge) is a priority. The range of motion for this hinge is 270 degrees from the folded position.

Continuous hinges, also called piano hinges, provide support to run the full length of the doors, panels, or pieces being joined together. They are manufactured in a variety of materials and sizes, with or without holes, finished or unfinished, and can be cut to specific sizes. They also vary by knuckle length, pin diameter, leaf thickness, and open width. The knuckle is the tubular part of the hinge through which the pin passes, and knuckle length is the measurement of an individual section. The pin runs the length of the hinge holding the leaves together. The leaf is the flat metal portion of the hinge that extends laterally from the knuckle and revolves around the pin. Open width is the dimension from the outer edge of one leaf to the outer edge of the other when the hinge is fully open.

Features

  • Surface-mounted for applications requiring continuous support along the full length of the hinge, such as appliance doors, industrial kitchen equipment, and metal storage cabinets
  • Stainless steel 304 is corrosion resistant up to 1,500 degrees F (though less resistant to corrosion than stainless steel 316), weldable, and stronger than steel and aluminum
  • Countersunk holes for convenience when mounting
  • Bright annealed finish for additional protection against corrosion and a polished, mirrorlike appearance
  • See more on Amazon...

Brand: Small Parts   |   Manufacturer: S&S Hinges

Package Dimensions: 1 x 1 x 36.2 inches (2.5 x 2.5 x 91.9 cm)

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #2

National Hardware N265-371 V570 Continuous Hinge in Nickel

Model: N265-371   |    Mpn: N265-371   |    Ean: 0038613265370   |    PartNumber: N265-371   |   Asin: B000BPB2OW

Whether for home, farm, builder or industrial customers, National has all the right hardware in the sizes and finishes you need. With over a century of service National is committed to maintaining the highest level of product quality, innovation and manufacturing technology. Providing quality hinges for all of your industrial, residential, commercial and specialty needs. From shutter to continuous hinges, specialty projects are easily completed with the breadth of unique hinges offered.

Features

  • Friction type pin will not fall out
  • Surface mount for easy installation
  • Manufactured from cold-rolled steel, with steel pin
  • Can be cut to desired length
  • See more on Amazon...

Brand: National Hardware   |   Manufacturer: National Hardware

Item Dimensions: 0.2 x 1.8 x 14 inches (0.5 x 4.6 x 35.6 cm)   |   Package Dimensions: 0.35 x 1.34 x 13.78 inches (0.9 x 3.4 x 35.0 cm)

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #3

Stainless Steel 304 Continuous Hinge with Hole, Bright Annealed Finish, 0.04" Leaf Thickness, 2" Open Width, 5/64" Pin Diameter, 1/2" Knuckle Length, 2' Long (Pack of 1)

Model: BA1004X24   |    Mpn: BA1004X24   |    PartNumber: BA1004X24   |   Asin: B007HBNWJ6

The stainless steel 304 continuous hinge has countersunk holes and is suitable for surface-mounted applications requiring uninterrupted support along the full length of the pieces being joined, such as appliance doors, industrial kitchen equipment, and metal storage cabinets. Stainless steel 304 resists corrosion up to 1,500 degrees F and is suitable for applications used in corrosive environments, though not as resistant to corrosion as stainless steel 316. A weldable material, stainless steel 304 is stronger than steel and aluminum. The bright annealed finish gives this hinge a mirrorlike appearance and offers additional protection against corrosion. This finished hinge is suited for applications such as cabinetry and piano lids where a polished hinge (as opposed to a flat finished or unfinished hinge) is a priority. The range of motion for this hinge is 270 degrees from the folded position.

Continuous hinges, also called piano hinges, provide support to run the full length of the doors, panels, or pieces being joined together. They are manufactured in a variety of materials and sizes, with or without holes, finished or unfinished, and can be cut to specific sizes. They also vary by knuckle length, pin diameter, leaf thickness, and open width. The knuckle is the tubular part of the hinge through which the pin passes, and knuckle length is the measurement of an individual section. The pin runs the length of the hinge holding the leaves together. The leaf is the flat metal portion of the hinge that extends laterally from the knuckle and revolves around the pin. Open width is the dimension from the outer edge of one leaf to the outer edge of the other when the hinge is fully open.

Features

  • Surface-mounted for applications requiring continuous support along the full length of the hinge, such as appliance doors, industrial kitchen equipment, and metal storage cabinets
  • Stainless steel 304 is corrosion resistant up to 1,500 degrees F (though less resistant to corrosion than stainless steel 316), weldable, and stronger than steel and aluminum
  • Countersunk holes for convenience when mounting
  • Bright annealed finish for additional protection against corrosion and a polished, mirrorlike appearance
  • See more on Amazon...

Brand: Small Parts   |   Manufacturer: S&S Hinges

Package Dimensions: 0.39 x 1.18 x 24.02 inches (1.0 x 3.0 x 61.0 cm)

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #4

Stainless Steel 304 Continuous Hinge with Hole, Bright Annealed Finish, 0.04" Leaf Thickness, 2" Open Width, 3/32" Pin Diameter, 1/2" Knuckle Length, 4' Long (Pack of 1)

 PartNumber: BA1004X48   |   Asin: B007HBNY3K

The stainless steel 304 continuous hinge has countersunk holes and is suitable for surface-mounted applications requiring uninterrupted support along the full length of the pieces being joined, such as appliance doors, industrial kitchen equipment, and metal storage cabinets. Stainless steel 304 resists corrosion up to 1,500 degrees F and is suitable for applications used in corrosive environments, though not as resistant to corrosion as stainless steel 316. A weldable material, stainless steel 304 is stronger than steel and aluminum. The bright annealed finish gives this hinge a mirrorlike appearance and offers additional protection against corrosion. This finished hinge is suited for applications such as cabinetry and piano lids where a polished hinge (as opposed to a flat finished or unfinished hinge) is a priority. The range of motion for this hinge is 270 degrees from the folded position.

Continuous hinges, also called piano hinges, provide support to run the full length of the doors, panels, or pieces being joined together. They are manufactured in a variety of materials and sizes, with or without holes, finished or unfinished, and can be cut to specific sizes. They also vary by knuckle length, pin diameter, leaf thickness, and open width. The knuckle is the tubular part of the hinge through which the pin passes, and knuckle length is the measurement of an individual section. The pin runs the length of the hinge holding the leaves together. The leaf is the flat metal portion of the hinge that extends laterally from the knuckle and revolves around the pin. Open width is the dimension from the outer edge of one leaf to the outer edge of the other when the hinge is fully open.

Features

  • Surface-mounted for applications requiring continuous support along the full length of the hinge, such as appliance doors, industrial kitchen equipment, and metal storage cabinets
  • Stainless steel 304 is corrosion resistant up to 1,500 degrees F (though less resistant to corrosion than stainless steel 316), weldable, and stronger than steel and aluminum
  • Countersunk holes for convenience when mounting
  • Bright annealed finish for additional protection against corrosion and a polished, mirrorlike appearance
  • See more on Amazon...

Brand: Small Parts   |   Manufacturer: S&S Hinges

Package Dimensions: 0.2 x 1.3 x 48 inches (0.5 x 3.3 x 121.9 cm)

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #5

Stainless Steel 304 Continuous Hinge with Holes, Unfinished, 0.06" Leaf Thickness, 2" Open Width, 1/8" Pin Diameter, 1/2" Knuckle Length, 6' Long (Pack of 1)

Model: 3-0636-0425   |    Mpn: 3-0636-0425   |    PartNumber: 3-0636-0425   |   Asin: B005J0JU5C

The stainless steel 304 continuous hinge has countersunk holes and is suitable for surface-mounted applications requiring uninterrupted support along the full length of the pieces being joined, such as appliance doors, industrial kitchen equipment, and metal storage cabinets. Stainless steel 304 resists corrosion up to 1,500 degrees F and is suitable for applications used in corrosive environments, though not as resistant to corrosion as stainless steel 316. A weldable material, stainless steel 304 is stronger than steel and aluminum. Since this hinge is unfinished, it is suited for applications that will not be exposed to corrosive environments. The range of motion for this hinge is 270 degrees from the folded position.

Continuous hinges, also called piano hinges, provide support to run the full length of the doors, panels, or pieces being joined together. They are manufactured in a variety of materials and sizes, with or without holes, finished or unfinished, and can be cut to specific sizes. They also vary by knuckle length, pin diameter, leaf thickness, and open width. The knuckle is the tubular part of the hinge through which the pin passes, and knuckle length is the measurement of an individual section. The pin runs the length of the hinge holding the leaves together. The leaf is the flat metal portion of the hinge that extends laterally from the knuckle and revolves around the pin. Open width is the dimension from the outer edge of one leaf to the outer edge of the other when the hinge is fully open.

Features

  • Surface-mounted for applications requiring continuous support along the full length of the hinge, such as cabinet lids, folding partitions, and metal storage cabinets
  • Stainless steel 304 is corrosion resistant up to 1,500 degrees F (though less resistant to corrosion than stainless steel 316), weldable, and stronger than steel and aluminum
  • Countersunk holes for convenience when mounting
  • Unfinished for projects with less exposure to corrosive environments
  • See more on Amazon...

Brand: Small Parts   |   Manufacturer: Stocker Hinge

Package Dimensions: 0.3 x 1.3 x 72 inches (0.8 x 3.3 x 182.9 cm)

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #6

Steel Plain Continuous Hinge with Holes, Unfinished, 0.06" Leaf Thickness, 3" Open Width, 1/8" Pin Diameter, 1/2" Knuckle Length, 4' Long (Pack of 1)

Model: 3-0638-0161   |    Mpn: 3-0638-0161   |    PartNumber: 3-0638-0161   |   Asin: B005J0WE3C

The unfinished steel continuous hinge has countersunk holes and is suitable for surface-mounted applications requiring uninterrupted support along the full length of the pieces being joined, such as cabinet lids, folding partitions, and metal storage cabinets. Steel is a stronger material than aluminum, but does not provide the same strength as stainless steel. It also resists rust and is weldable. Since this hinge is unfinished, it is suited for applications that will not be exposed to corrosive environments. The range of motion for this hinge is 270 degrees from the folded position.

Continuous hinges, also called piano hinges, provide support to run the full length of the doors, panels, or pieces being joined together. They are manufactured in a variety of materials and sizes, with or without holes, finished or unfinished, and can be cut to specific sizes. They also vary by knuckle length, pin diameter, leaf thickness, and open width. The knuckle is the tubular part of the hinge through which the pin passes, and knuckle length is the measurement of an individual section. The pin runs the length of the hinge holding the leaves together. The leaf is the flat metal portion of the hinge that extends laterally from the knuckle and revolves around the pin. Open width is the dimension from the outer edge of one leaf to the outer edge of the other when the hinge is fully open.

Features

  • Surface-mounted for applications requiring continuous support along the full length of the hinge, such as cabinet lids, folding partitions, and metal storage cabinets
  • Steel is stronger than aluminum, rust resistant, and weldable
  • Countersunk holes for convenience when mounting
  • Unfinished for projects with less exposure to corrosive environments
  • See more on Amazon...

Brand: Small Parts   |   Manufacturer: Stocker Hinge

Package Dimensions: 0.5 x 1.75 x 48.25 inches (1.3 x 4.4 x 122.6 cm)

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #7

Stainless Steel 304 Continuous Hinge with Holes, Unfinished, 0.042" Leaf Thickness, 2" Open Width, 3/32" Pin Diameter, 1/2" Knuckle Length, 1' Long (Pack of 1)

Model: 3-0536-0330   |    Mpn: 3-0536-0330   |    PartNumber: 3-0536-0330   |   Asin: B005J0WTLO

The stainless steel 304 continuous hinge has countersunk holes and is suitable for surface-mounted applications requiring uninterrupted support along the full length of the pieces being joined, such as appliance doors, industrial kitchen equipment, and metal storage cabinets. Stainless steel 304 resists corrosion up to 1,500 degrees F and is suitable for applications used in corrosive environments, though not as resistant to corrosion as stainless steel 316. A weldable material, stainless steel 304 is stronger than steel and aluminum. Since this hinge is unfinished, it is suited for applications that will not be exposed to corrosive environments. The range of motion for this hinge is 270 degrees from the folded position.

Continuous hinges, also called piano hinges, provide support to run the full length of the doors, panels, or pieces being joined together. They are manufactured in a variety of materials and sizes, with or without holes, finished or unfinished, and can be cut to specific sizes. They also vary by knuckle length, pin diameter, leaf thickness, and open width. The knuckle is the tubular part of the hinge through which the pin passes, and knuckle length is the measurement of an individual section. The pin runs the length of the hinge holding the leaves together. The leaf is the flat metal portion of the hinge that extends laterally from the knuckle and revolves around the pin. Open width is the dimension from the outer edge of one leaf to the outer edge of the other when the hinge is fully open.

Features

  • Surface-mounted for applications requiring continuous support along the full length of the hinge, such as cabinet lids, folding partitions, and metal storage cabinets
  • Stainless steel 304 is corrosion resistant up to 1,500 degrees F (though less resistant to corrosion than stainless steel 316), weldable, and stronger than steel and aluminum
  • Countersunk holes for convenience when mounting
  • Unfinished for projects with less exposure to corrosive environments
  • See more on Amazon...

Brand: Small Parts   |   Manufacturer: Stocker Hinge

Package Dimensions: 0.1 x 10.8 x 11 inches (0.3 x 27.4 x 27.9 cm)

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #8

Stainless Steel 304 Continuous Hinge with Hole, Bright Annealed Finish, 0.04" Leaf Thickness, 2" Open Width, 5/64" Pin Diameter, 1/2" Knuckle Length, 3' Long (Pack of 1)

 PartNumber: BA1004X36   |   Asin: B007HBNXCC

The stainless steel 304 continuous hinge has countersunk holes and is suitable for surface-mounted applications requiring uninterrupted support along the full length of the pieces being joined, such as appliance doors, industrial kitchen equipment, and metal storage cabinets. Stainless steel 304 resists corrosion up to 1,500 degrees F and is suitable for applications used in corrosive environments, though not as resistant to corrosion as stainless steel 316. A weldable material, stainless steel 304 is stronger than steel and aluminum. The bright annealed finish gives this hinge a mirrorlike appearance and offers additional protection against corrosion. This finished hinge is suited for applications such as cabinetry and piano lids where a polished hinge (as opposed to a flat finished or unfinished hinge) is a priority. The range of motion for this hinge is 270 degrees from the folded position.

Continuous hinges, also called piano hinges, provide support to run the full length of the doors, panels, or pieces being joined together. They are manufactured in a variety of materials and sizes, with or without holes, finished or unfinished, and can be cut to specific sizes. They also vary by knuckle length, pin diameter, leaf thickness, and open width. The knuckle is the tubular part of the hinge through which the pin passes, and knuckle length is the measurement of an individual section. The pin runs the length of the hinge holding the leaves together. The leaf is the flat metal portion of the hinge that extends laterally from the knuckle and revolves around the pin. Open width is the dimension from the outer edge of one leaf to the outer edge of the other when the hinge is fully open.

Features

  • Surface-mounted for applications requiring continuous support along the full length of the hinge, such as appliance doors, industrial kitchen equipment, and metal storage cabinets
  • Stainless steel 304 is corrosion resistant up to 1,500 degrees F (though less resistant to corrosion than stainless steel 316), weldable, and stronger than steel and aluminum
  • Countersunk holes for convenience when mounting
  • Bright annealed finish for additional protection against corrosion and a polished, mirrorlike appearance
  • See more on Amazon...

Brand: Small Parts   |   Manufacturer: S&S Hinges

Package Dimensions: 0.1 x 1.15 x 24 inches (0.3 x 2.9 x 61.0 cm)

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #9

Stainless Steel 304 Continuous Hinge with Holes, Unfinished, 0.06" Leaf Thickness, 2" Open Width, 1/8" Pin Diameter, 1/2" Knuckle Length, 2' Long (Pack of 1)

 PartNumber: 3-0636-1168   |   Asin: B007XZGLPS

Stainless steel 304 continuous hinge with holes, unfinished. Leaf thickness: 0.06". Open width: 2". Pin diameter: 1/8". Knuckle length: 1/2". Long: 2'.

Features

  • Made of stainless steel 304
  • Continuous hinge with holes
  • Unfinished
  • Range of motion: 270 degrees minimum
  • Knuckle length: 1/2
  • See more on Amazon...

Brand: Stocker Hinge   |   Manufacturer: Stocker Hinge

Package Dimensions: 0.12 x 1.26 x 24.02 inches (0.3 x 3.2 x 61.0 cm)

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #10

Aluminum 3003 Continuous Hinge with Holes, Unfinished, 0.06" Leaf Thickness, 2" Open Width, 1/8" Pin Diameter, 1/2" Knuckle Length, 4' Long (Pack of 1)

Model: 3-0636-0424   |    Mpn: 3-0636-0424   |    PartNumber: 3-0636-0424   |   Asin: B005J0WC2U

The aluminum 3003 continuous hinge has countersunk holes and is suitable for surface-mounted applications requiring uninterrupted support along the full length of the pieces being joined. This hinge is suitable for hollow metal doors and frames, and for use with wood and aluminum. Aluminum 3003 is lightweight, weldable, and more corrosion resistant than steel. However, aluminum 3003 does not provide the same strength as aluminum 5052, stainless steel, or steel and is less corrosion resistant than aluminum 5052. Since the hinge is unfinished, it is suited for applications that will not be exposed to corrosive environments. The range of motion for this hinge is 270 degrees from the folded position.

Continuous hinges, also called piano hinges, provide support to run the full length of the doors, panels, or pieces being joined together. They are manufactured in a variety of materials and sizes, with or without holes, finished or unfinished, and can be cut to specific sizes. They also vary by knuckle length, pin diameter, leaf thickness, and open width. The knuckle is the tubular part of the hinge through which the pin passes, and knuckle length is the measurement of an individual section. The pin runs the length of the hinge holding the leaves together. The leaf is the flat metal portion of the hinge that extends laterally from the knuckle and revolves around the pin. Open width is the dimension from the outer edge of one leaf to the outer edge of the other when the hinge is fully open.

Features

  • Surface-mounted for applications requiring continuous support along the full length of the hinge, such as hollow metal doors and frames, and for use with wood and aluminum
  • Aluminum 3003 is lightweight, weldable, and more corrosion resistant than steel, though not as strong or corrosive resistant as aluminum 5052
  • Countersunk holes for convenience when mounting
  • Unfinished for projects with less exposure to corrosive environments
  • See more on Amazon...

Brand: Small Parts   |   Manufacturer: Stocker Hinge

Package Dimensions: 0.3 x 1.3 x 48 inches (0.8 x 3.3 x 121.9 cm)

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #11

Aluminum 3003 Continuous Hinge with Holes, Unfinished, 0.06" Leaf Thickness, 1-1/2" Open Width, 1/8" Pin Diameter, 1/2" Knuckle Length, 3' Long (Pack of 1)

Model: 3-0635-0357   |    Mpn: 3-0635-0357   |    PartNumber: 3-0635-0357   |   Asin: B005J0WU6S

The aluminum 3003 continuous hinge has countersunk holes and is suitable for surface-mounted applications requiring uninterrupted support along the full length of the pieces being joined. This hinge is suitable for hollow metal doors and frames, and for use with wood and aluminum. Aluminum 3003 is lightweight, weldable, and more corrosion resistant than steel. However, aluminum 3003 does not provide the same strength as aluminum 5052, stainless steel, or steel and is less corrosion resistant than aluminum 5052. Since the hinge is unfinished, it is suited for applications that will not be exposed to corrosive environments. The range of motion for this hinge is 270 degrees from the folded position.

Continuous hinges, also called piano hinges, provide support to run the full length of the doors, panels, or pieces being joined together. They are manufactured in a variety of materials and sizes, with or without holes, finished or unfinished, and can be cut to specific sizes. They also vary by knuckle length, pin diameter, leaf thickness, and open width. The knuckle is the tubular part of the hinge through which the pin passes, and knuckle length is the measurement of an individual section. The pin runs the length of the hinge holding the leaves together. The leaf is the flat metal portion of the hinge that extends laterally from the knuckle and revolves around the pin. Open width is the dimension from the outer edge of one leaf to the outer edge of the other when the hinge is fully open.

Features

  • Surface-mounted for applications requiring continuous support along the full length of the hinge, such as hollow metal doors and frames, and for use with wood and aluminum
  • Aluminum 3003 is lightweight, weldable, and more corrosion resistant than steel, though not as strong or corrosive resistant as aluminum 5052
  • Countersunk holes for convenience when mounting
  • Unfinished for projects with less exposure to corrosive environments
  • See more on Amazon...

Brand: Small Parts   |   Manufacturer: Stocker Hinge

Package Dimensions: 0.5 x 1.25 x 36.25 inches (1.3 x 3.2 x 92.1 cm)

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #12

National Hardware N265-355 V570 Continuous Hinge in Brass

Model: N265-355   |    Mpn: N265-355   |    Ean: 0038613265356   |    PartNumber: N265-355   |   Asin: B000BQL444

Whether for home, farm, builder or industrial customers, National has all the right hardware in the sizes and finishes you need. With over a century of service National is committed to maintaining the highest level of product quality, innovation and manufacturing technology. Providing quality hinges for all of your industrial, residential, commercial and specialty needs. From shutter to continuous hinges, specialty projects are easily completed with the breadth of unique hinges offered.

Features

  • Friction type pin will not fall out
  • Surface mount for easy installation
  • Manufactured from cold-rolled steel, with steel pin
  • Can be cut to desired length
  • See more on Amazon...

Brand: National Hardware   |   Manufacturer: National Hardware

Item Dimensions: 1 x 1.9 x 14 inches (2.5 x 4.8 x 35.6 cm)   |   Package Dimensions: 0.2 x 1.5 x 13 inches (0.5 x 3.8 x 33.0 cm)

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #13

Muzata Heavy Duty 304 Stainless Steel Continuous Piano Hinge 2"x24" 0.060" Thick with Screws,Bright Annealed Finish

 Ean: 0710654719929   |    PartNumber: MZZ379   |   Asin: B07N2H8SPP

Package

1PCS 304 Stainless steel 2" wide x 24" long piano hinge

24PCS Matching installation screws

Features

  • Continuous hinges also called piano hinges,provide support to run the full length of the doors,panels,industrial kitchen equipment and metal storage cabinets or pieces being joined together
  • This continuous hinges is 24long 2 wide and 0.06 thick ,so if you need something that will last for years in just about any environment
  • For doors,fold-down seats, or a host of other applications,It's great ideal continuous hinge for the good job
  • The continuous Piano Hinge is made of 304 stainless steel that weldable and stronger than steel and aluminum
  • SCREWS INCLUDED - it come with 20PCS matching screws for your convenience
  • See more on Amazon...

Brand: Muzata   |   Manufacturer: Muazta

Package Dimensions: 0.94 x 1.69 x 24.17 inches (2.4 x 4.3 x 61.4 cm)

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #14

Small Parts Steel Plain Continuous Hinge with Holes, Unfinished, 0.06" Leaf Thickness, 2" Open Width, 1/8" Pin Diameter, 1/2" Knuckle Length, 4' Long (Pack of 1) - 3-0636-0421

Model: 3-0636-0421   |    Mpn: 3-0636-0421   |    PartNumber: 3-0636-0421   |   Asin: B005J0WAZO

The unfinished steel continuous hinge has countersunk holes and is suitable for surface-mounted applications requiring uninterrupted support along the full length of the pieces being joined, such as cabinet lids, folding partitions, and metal storage cabinets. Steel is a stronger material than aluminum, but does not provide the same strength as stainless steel. It also resists rust and is weldable. Since this hinge is unfinished, it is suited for applications that will not be exposed to corrosive environments. The range of motion for this hinge is 270 degrees from the folded position.

Continuous hinges, also called piano hinges, provide support to run the full length of the doors, panels, or pieces being joined together. They are manufactured in a variety of materials and sizes, with or without holes, finished or unfinished, and can be cut to specific sizes. They also vary by knuckle length, pin diameter, leaf thickness, and open width. The knuckle is the tubular part of the hinge through which the pin passes, and knuckle length is the measurement of an individual section. The pin runs the length of the hinge holding the leaves together. The leaf is the flat metal portion of the hinge that extends laterally from the knuckle and revolves around the pin. Open width is the dimension from the outer edge of one leaf to the outer edge of the other when the hinge is fully open.

Features

  • Surface-mounted for applications requiring continuous support along the full length of the hinge, such as cabinet lids, folding partitions, and metal storage cabinets
  • Steel is stronger than aluminum, rust resistant, and weldable
  • Countersunk holes for convenience when mounting
  • Unfinished for projects with less exposure to corrosive environments
  • See more on Amazon...

Brand: Small Parts   |   Manufacturer: Stocker Hinge

Package Dimensions: 0.2 x 1.2 x 48 inches (0.5 x 3.0 x 121.9 cm)

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #15

RMP Aluminum Continuous Hinge, 3" Open, 72" Length, 0.093" Thickness.250 Pin Diameter, No Holes, Unfinished

Model: OL-408050-6F   |    Mpn: OL-408050-6F   |    PartNumber: OL-408050-6F   |   Asin: B00LOUIBTM

The continuous aluminum hinge, also knows as piano hinge, has no holes and is great for custom projects. It is great for door and many other uses. The hinge has a 270 degree range. It can be welded or drilled for easy application to wood or metal.

Features

  • Suitable for projects needing continuous support
  • Great weldability
  • No holes provides for diverse mounting such as welding or drilling
  • See more on Amazon...

Brand: RMP   |   Manufacturer: Rose Metal Products

Item Dimensions: 3 x 3 x 72 inches (7.6 x 7.6 x 182.9 cm)   |   Package Dimensions: 2.25 x 2.25 x 74 inches (5.7 x 5.7 x 188.0 cm)

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #16

Aluminum 3003 Continuous Hinge with Holes, Unfinished, 0.06" Leaf Thickness, 2" Open Width, 1/8" Pin Diameter, 1/2" Knuckle Length, 6' Long (Pack of 1)

Model: 3-0636-0423   |    Mpn: 3-0636-0423   |    PartNumber: 3-0636-0423   |   Asin: B005J0JTC6

The aluminum 3003 continuous hinge has countersunk holes and is suitable for surface-mounted applications requiring uninterrupted support along the full length of the pieces being joined. This hinge is suitable for hollow metal doors and frames, and for use with wood and aluminum. Aluminum 3003 is lightweight, weldable, and more corrosion resistant than steel. However, aluminum 3003 does not provide the same strength as aluminum 5052, stainless steel, or steel and is less corrosion resistant than aluminum 5052. Since the hinge is unfinished, it is suited for applications that will not be exposed to corrosive environments. The range of motion for this hinge is 270 degrees from the folded position.

Continuous hinges, also called piano hinges, provide support to run the full length of the doors, panels, or pieces being joined together. They are manufactured in a variety of materials and sizes, with or without holes, finished or unfinished, and can be cut to specific sizes. They also vary by knuckle length, pin diameter, leaf thickness, and open width. The knuckle is the tubular part of the hinge through which the pin passes, and knuckle length is the measurement of an individual section. The pin runs the length of the hinge holding the leaves together. The leaf is the flat metal portion of the hinge that extends laterally from the knuckle and revolves around the pin. Open width is the dimension from the outer edge of one leaf to the outer edge of the other when the hinge is fully open.

Features

  • Surface-mounted for applications requiring continuous support along the full length of the hinge, such as hollow metal doors and frames, and for use with wood and aluminum
  • Aluminum 3003 is lightweight, weldable, and more corrosion resistant than steel, though not as strong or corrosive resistant as aluminum 5052
  • Countersunk holes for convenience when mounting
  • Unfinished for projects with less exposure to corrosive environments
  • See more on Amazon...

Brand: Small Parts   |   Manufacturer: Stocker Hinge

Package Dimensions: 0.25 x 2 x 72.25 inches (0.6 x 5.1 x 183.5 cm)

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #17

Stainless Steel 304 Continuous Hinge with Holes, Unfinished, 0.06" Leaf Thickness, 2" Open Width, 1/8" Pin Diameter, 1/2" Knuckle Length, 4' Long (Pack of 1)

Model: 3-0636-0419   |    Mpn: 3-0636-0419   |    Ean: 0641927022227   |    PartNumber: 3-0636-0419   |   Asin: B005J0JSOK

The stainless steel 304 continuous hinge has countersunk holes and is suitable for surface-mounted applications requiring uninterrupted support along the full length of the pieces being joined, such as appliance doors, industrial kitchen equipment, and metal storage cabinets. Stainless steel 304 resists corrosion up to 1,500 degrees F and is suitable for applications used in corrosive environments, though not as resistant to corrosion as stainless steel 316. A weldable material, stainless steel 304 is stronger than steel and aluminum. Since this hinge is unfinished, it is suited for applications that will not be exposed to corrosive environments. The range of motion for this hinge is 270 degrees from the folded position.

Continuous hinges, also called piano hinges, provide support to run the full length of the doors, panels, or pieces being joined together. They are manufactured in a variety of materials and sizes, with or without holes, finished or unfinished, and can be cut to specific sizes. They also vary by knuckle length, pin diameter, leaf thickness, and open width. The knuckle is the tubular part of the hinge through which the pin passes, and knuckle length is the measurement of an individual section. The pin runs the length of the hinge holding the leaves together. The leaf is the flat metal portion of the hinge that extends laterally from the knuckle and revolves around the pin. Open width is the dimension from the outer edge of one leaf to the outer edge of the other when the hinge is fully open.

Features

  • Surface-mounted for applications requiring continuous support along the full length of the hinge, such as cabinet lids, folding partitions, and metal storage cabinets
  • Stainless steel 304 is corrosion resistant up to 1,500 degrees F (though less resistant to corrosion than stainless steel 316), weldable, and stronger than steel and aluminum
  • Countersunk holes for convenience when mounting
  • Unfinished for projects with less exposure to corrosive environments
  • See more on Amazon...

Brand: Small Parts   |   Manufacturer: Stocker Hinge

Package Dimensions: 0.3 x 1.2 x 48 inches (0.8 x 3.0 x 121.9 cm)

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #18

Stainless Steel 304 Continuous Hinge with Holes, Unfinished, 0.042" Leaf Thickness, 1-1/16" Open Width, 3/32" Pin Diameter, 1/2" Knuckle Length, 2.5' Long (Pack of 1)

Model: 3-0530-0274   |    Mpn: 3-0530-0274   |    PartNumber: 3-0530-0274   |   Asin: B005J0VWSA

The stainless steel 304 continuous hinge has countersunk holes and is suitable for surface-mounted applications requiring uninterrupted support along the full length of the pieces being joined, such as appliance doors, industrial kitchen equipment, and metal storage cabinets. Stainless steel 304 resists corrosion up to 1,500 degrees F and is suitable for applications used in corrosive environments, though not as resistant to corrosion as stainless steel 316. A weldable material, stainless steel 304 is stronger than steel and aluminum. Since this hinge is unfinished, it is suited for applications that will not be exposed to corrosive environments. The range of motion for this hinge is 270 degrees from the folded position.

Continuous hinges, also called piano hinges, provide support to run the full length of the doors, panels, or pieces being joined together. They are manufactured in a variety of materials and sizes, with or without holes, finished or unfinished, and can be cut to specific sizes. They also vary by knuckle length, pin diameter, leaf thickness, and open width. The knuckle is the tubular part of the hinge through which the pin passes, and knuckle length is the measurement of an individual section. The pin runs the length of the hinge holding the leaves together. The leaf is the flat metal portion of the hinge that extends laterally from the knuckle and revolves around the pin. Open width is the dimension from the outer edge of one leaf to the outer edge of the other when the hinge is fully open.

Features

  • Surface-mounted for applications requiring continuous support along the full length of the hinge, such as cabinet lids, folding partitions, and metal storage cabinets
  • Stainless steel 304 is corrosion resistant up to 1,500 degrees F (though less resistant to corrosion than stainless steel 316), weldable, and stronger than steel and aluminum
  • Countersunk holes for convenience when mounting
  • Unfinished for projects with less exposure to corrosive environments
  • See more on Amazon...

Brand: Small Parts   |   Manufacturer: Stocker Hinge

Package Dimensions: 0.2 x 0.7 x 30 inches (0.5 x 1.8 x 76.2 cm)

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #19

Aluminum 3003 Continuous Hinge with Holes, Unfinished, 0.06" Leaf Thickness, 2" Open Width, 1/8" Pin Diameter, 1/2" Knuckle Length, 3' Long (Pack of 1)

Model: 3-0636-0889   |    Mpn: 3-0636-0889   |    PartNumber: 3-0636-0889   |   Asin: B005J0WVAI

The aluminum 3003 continuous hinge has countersunk holes and is suitable for surface-mounted applications requiring uninterrupted support along the full length of the pieces being joined. This hinge is suitable for hollow metal doors and frames, and for use with wood and aluminum. Aluminum 3003 is lightweight, weldable, and more corrosion resistant than steel. However, aluminum 3003 does not provide the same strength as aluminum 5052, stainless steel, or steel and is less corrosion resistant than aluminum 5052. Since the hinge is unfinished, it is suited for applications that will not be exposed to corrosive environments. The range of motion for this hinge is 270 degrees from the folded position.

Continuous hinges, also called piano hinges, provide support to run the full length of the doors, panels, or pieces being joined together. They are manufactured in a variety of materials and sizes, with or without holes, finished or unfinished, and can be cut to specific sizes. They also vary by knuckle length, pin diameter, leaf thickness, and open width. The knuckle is the tubular part of the hinge through which the pin passes, and knuckle length is the measurement of an individual section. The pin runs the length of the hinge holding the leaves together. The leaf is the flat metal portion of the hinge that extends laterally from the knuckle and revolves around the pin. Open width is the dimension from the outer edge of one leaf to the outer edge of the other when the hinge is fully open.

Features

  • Surface-mounted for applications requiring continuous support along the full length of the hinge, such as hollow metal doors and frames, and for use with wood and aluminum
  • Aluminum 3003 is lightweight, weldable, and more corrosion resistant than steel, though not as strong or corrosive resistant as aluminum 5052
  • Countersunk holes for convenience when mounting
  • Unfinished for projects with less exposure to corrosive environments
  • See more on Amazon...

Brand: Small Parts   |   Manufacturer: Stocker Hinge

Package Dimensions: 0.2 x 0.2 x 36 inches (0.5 x 0.5 x 91.4 cm)

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #20

National Hardware N265-389 V570 Continuous Hinge in Nickel

Model: N265-389   |    Mpn: N265389   |    Ean: 0038613265387   |    PartNumber: N265389   |   Asin: B000B4KZTG

Whether for home, farm, builder or industrial customers, National has all the right hardware in the sizes and finishes you need. With over a century of service National is committed to maintaining the highest level of product quality, innovation and manufacturing technology. Providing quality hinges for all of your industrial, residential, commercial and specialty needs. From shutter to continuous hinges, specialty projects are easily completed with the breadth of unique hinges offered.

Features

  • Friction type pin will not fall out
  • Surface mount for easy installation
  • Manufactured from cold-rolled steel, with steel pin
  • Can be cut to desired length
  • See more on Amazon...

Brand: National Hardware   |   Manufacturer: National Hardware

Item Dimensions: 0.2 x 1.8 x 14 inches (0.5 x 4.6 x 35.6 cm)   |   Package Dimensions: 0.98 x 2.01 x 14.02 inches (2.5 x 5.1 x 35.6 cm)

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon




Looking For Something Else? Search

Most Popular
New Releases

  1. Stainless Steel 304 Continuous Hinge with Hole, Bright Annealed Finish, 0.04" Leaf Thickness, 1-1/2"...
  2. National Hardware N265-371 V570 Continuous Hinge in Nickel
  3. Stainless Steel 304 Continuous Hinge with Hole, Bright Annealed Finish, 0.04" Leaf Thickness, 2" Ope...
  4. Stainless Steel 304 Continuous Hinge with Hole, Bright Annealed Finish, 0.04" Leaf Thickness, 2" Ope...
  5. Stainless Steel 304 Continuous Hinge with Holes, Unfinished, 0.06" Leaf Thickness, 2" Open Width, 1/...
  6. Steel Plain Continuous Hinge with Holes, Unfinished, 0.06" Leaf Thickness, 3" Open Width, 1/8" Pin D...
  7. Stainless Steel 304 Continuous Hinge with Holes, Unfinished, 0.042" Leaf Thickness, 2" Open Width, 3...
  8. Stainless Steel 304 Continuous Hinge with Hole, Bright Annealed Finish, 0.04" Leaf Thickness, 2" Ope...
  9. Stainless Steel 304 Continuous Hinge with Holes, Unfinished, 0.06" Leaf Thickness, 2" Open Width, 1/...
  10. Aluminum 3003 Continuous Hinge with Holes, Unfinished, 0.06" Leaf Thickness, 2" Open Width, 1/8" Pin...

Most Wished For

  1. Stainless Steel 304 Continuous Hinge with Hole, Bright Annealed Finish, 0.04" Leaf Thickness, 1-1/2"...
  2. National Hardware N265-371 V570 Continuous Hinge in Nickel
  3. Stainless Steel 304 Continuous Hinge with Hole, Bright Annealed Finish, 0.04" Leaf Thickness, 2" Ope...
  4. Stainless Steel 304 Continuous Hinge with Hole, Bright Annealed Finish, 0.04" Leaf Thickness, 2" Ope...
  5. Stainless Steel 304 Continuous Hinge with Holes, Unfinished, 0.06" Leaf Thickness, 2" Open Width, 1/...
  6. Steel Plain Continuous Hinge with Holes, Unfinished, 0.06" Leaf Thickness, 3" Open Width, 1/8" Pin D...
  7. Stainless Steel 304 Continuous Hinge with Holes, Unfinished, 0.042" Leaf Thickness, 2" Open Width, 3...
  8. Stainless Steel 304 Continuous Hinge with Hole, Bright Annealed Finish, 0.04" Leaf Thickness, 2" Ope...
  9. Stainless Steel 304 Continuous Hinge with Holes, Unfinished, 0.06" Leaf Thickness, 2" Open Width, 1/...
  10. Aluminum 3003 Continuous Hinge with Holes, Unfinished, 0.06" Leaf Thickness, 2" Open Width, 1/8" Pin...

Most Gifted

  1. Stainless Steel 304 Continuous Hinge with Hole, Bright Annealed Finish, 0.04" Leaf Thickness, 1-1/2"...
  2. National Hardware N265-371 V570 Continuous Hinge in Nickel
  3. Stainless Steel 304 Continuous Hinge with Hole, Bright Annealed Finish, 0.04" Leaf Thickness, 2" Ope...
  4. Stainless Steel 304 Continuous Hinge with Hole, Bright Annealed Finish, 0.04" Leaf Thickness, 2" Ope...
  5. Stainless Steel 304 Continuous Hinge with Holes, Unfinished, 0.06" Leaf Thickness, 2" Open Width, 1/...
  6. Steel Plain Continuous Hinge with Holes, Unfinished, 0.06" Leaf Thickness, 3" Open Width, 1/8" Pin D...
  7. Stainless Steel 304 Continuous Hinge with Holes, Unfinished, 0.042" Leaf Thickness, 2" Open Width, 3...
  8. Stainless Steel 304 Continuous Hinge with Hole, Bright Annealed Finish, 0.04" Leaf Thickness, 2" Ope...
  9. Stainless Steel 304 Continuous Hinge with Holes, Unfinished, 0.06" Leaf Thickness, 2" Open Width, 1/...
  10. Aluminum 3003 Continuous Hinge with Holes, Unfinished, 0.06" Leaf Thickness, 2" Open Width, 1/8" Pin...

Top Selling

  1. Stainless Steel 304 Continuous Hinge with Hole, Bright Annealed Finish, 0.04" Leaf Thickness, 1-1/2"...
  2. National Hardware N265-371 V570 Continuous Hinge in Nickel
  3. Stainless Steel 304 Continuous Hinge with Hole, Bright Annealed Finish, 0.04" Leaf Thickness, 2" Ope...
  4. Stainless Steel 304 Continuous Hinge with Hole, Bright Annealed Finish, 0.04" Leaf Thickness, 2" Ope...
  5. Stainless Steel 304 Continuous Hinge with Holes, Unfinished, 0.06" Leaf Thickness, 2" Open Width, 1/...
  6. Steel Plain Continuous Hinge with Holes, Unfinished, 0.06" Leaf Thickness, 3" Open Width, 1/8" Pin D...
  7. Stainless Steel 304 Continuous Hinge with Holes, Unfinished, 0.042" Leaf Thickness, 2" Open Width, 3...
  8. Stainless Steel 304 Continuous Hinge with Hole, Bright Annealed Finish, 0.04" Leaf Thickness, 2" Ope...
  9. Stainless Steel 304 Continuous Hinge with Holes, Unfinished, 0.06" Leaf Thickness, 2" Open Width, 1/...
  10. Aluminum 3003 Continuous Hinge with Holes, Unfinished, 0.06" Leaf Thickness, 2" Open Width, 1/8" Pin...



Main Categories

Home & Garden


Home Improvement


Electronics


Office


Car & Automotive


Sporting Goods


Toys and Hobby


Health & Personal Care


Beauty Supplies


Fashion


Industrial


Related Categories

Abrasive & Finishing


Cutting Tools


Fasteners


Filtration


Commercial Door Products


Hydraulics, Pneumatics & Plumbing


Industrial Hardware


Industrial Tools


Food Services


Janitorial & Sanitation


Lab Equipment


Material Handling


Occupational Health


Packaging & Shipping


Power Transmission


Dental Supplies


Medical Supplies


Raw Materials


Retail Fixtures & Equipment


Tapes, Adhesives & Sealants


Test, Measure & Inspect


Robotics, 3D Printing & Science Education


Industrial Electrical



We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
Certain content that appears on GistGear.com comes from Amazon services llc. This content is provided 'as is' and is subject to change or removal at any time.
Any price and availability information displayed on Amazon.com at the time of purchase will apply to the purchase of this product.
Amazon product prices and availability are accurate as of the date/time indicated and are subject to change.