Frontpage > Industrial > Test, Measure & Inspect > Differential Pressure Gauges

Best Differential Pressure Gauges - Buying Guide

Last Updated: 11/20/2018

Share on


  #1

Dwyer Capsuhelic Series 4000 Differential Pressure Gauge, Range 0-50"WC

Model: 4050   |    Mpn: 4050   |    PartNumber: 4050   |   Asin: B009P8RCHM

The Dwyer Capsuhelic series 4000 differential pressure gauge with an aluminum case has a circular 4" (100 mm) dial, and four female 1/4" NPT rate connections, and measures pressure with single scale in inch water column (WC), mm WC, cm WC, psid, or kPa with a display accuracy of + or - 3 or 4%. The die-cast aluminum case with impregnated hard coating is for measuring air and compatible gases and oil-based liquids. The circular dial is 4" in diameter and measures pressure with a single scale in inch water column (WC), mm WC, cm WC, psid, or kPa. The pressure being measured is held within a capsule in the gauge, which permits the use of the gauge on system pressures of up to 500 psig, even with differentials less than 0.1 in WC. The gauge accuracy is + or - 3% of full scale at 70 degrees F (21.1 degrees C) with + or - 4% of full scale on some models. The pressure limits are -20" Hg. to 500 psig. The temperature limit is 20 to 200 degrees F (-6.67 to 93.3 degrees C). Four female connections with 1/4" NPT (National Pipe Thread) rate provide for vertical mounting of the gauge. The connections are paired with one high and low pressure pair of taps on top for air and gas and one high and low pressure pair on bottom for liquids. This gauge is suitable as a readout device when measuring flowing fluids, pressure drop across filters, liquid levels in storage tanks, and other applications involving pressure, vacuum, or differential pressure. The gauge comes with two 1/4" NPT plugs for duplicate pressure taps, four flush mounting adapters with screws, and four surface mounting screws.

Pressure gauges are instruments used to measure the pressure of a gas or liquid inside a vessel and, often, to help ensure the optimal amount of pressure for a given application. Pressure gauges can range from everyday instruments, such as those used to measure the air pressure in a car or bicycle tire, to highly accurate gauges used in mechanical and industrial processing. Most often, pressure gauges measure pressure relative to another reference. For instance, gauge pressure measures pressure relative to ambient air. An example of a pressure gauge measuring relative to ambient air is a tire pressure gauge or a blood pressure gauge. Differential pressure is the difference in pressure between two points, such as when measuring liquid flow along various points in a pipeline. An absolute pressure gauge measures pressure relative to a perfect vacuum, such as an atmospheric or barometric pressure gauge. All types of pressure gauges include either a male or a female mount to connect to the vessel where pressure is being measured, and display results on a dial with varying increments of measure across a given range.

Dwyer Instruments manufactures measurement and control instruments, including pressure gauges, flow meters, level instrumentation, temperature instrumentation, and air quality monitors. The company, founded in 1931, is headquartered in Michigan City, IN.

What's in the Box? Dwyer Capsuhelic series 4000 differential pressure gauge 1/4" NPT plugs (2) Flush mounting adapters with screws (4) Surface mounting screws (4)

Features

  • Aluminum case for use with air and compatible gases and oil-based liquids
  • Circular dial is 4 (100 mm) in diameter
  • Measures pressure with single scale in inch water column (WC), mm WC, cm WC, psid, or kPa
  • Display accuracy is + or - 0.5% over the entire range of the gauge (ASME B40.100 Grade 2A)
  • Four female connections with 1/4 NPT rate paired at top and bottom
  • See more on Amazon...

Brand: Dwyer   |   Manufacturer: Dwyer Instruments

Package Dimensions: 3.2 x 5.9 x 6.1 inches (8.1 x 15.0 x 15.5 cm)

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #2

Dwyer Minihelic II Series 2-5000 Differential Pressure Gauge, Range 0-100 mm WC

Model: 2-5000-100MM   |    Mpn: 2-5000-100MM   |    PartNumber: 2-5000-100MM   |   Asin: B009PC65JO

Combining clean design, small size and low cost with enough accuracy for all but the most demanding applications our Minihelic II gage offers the latest in design features for a dial type differential pressure gage. It is our most compact gage but is easy to read and can safely operate at total pressures up to 30 psig. The Minihelic II gage is designed for panel mounting in a single 2-5/8" diameter hole. Standard pressure connections are barbed fittings for 3/16" ID tubing; optional 1/8" male NPT connections are also available. Over-pressure protection is built into the Minihelic II gage by means of a blow-out membrane molded in conjunction with the diaphragm. Accidental over-ranging up to the rated total pressure will not damage the gage. With removable lens and rear housing, the gage may be easily serviced at minimum cost. With the housing molded from mineral and glass filled nylon and the lens molded from acrylic, the gage will withstand rough use and exposure as well as high total pressure. The 5% accuracy and low cost of the Minihelic II gage make it well-suited for a wide variety of OEM and user applications. OEM applications include cabinet air purging, medical respiratory therapy equipment, air samplers, laminar flow hoods, and electronic air cooling systems. As an air filter gage, the Minihelic II gage finds many end use applications on large stationary engines, compressors, ventilators, and air handling units. The Minihelic II gage is suitable for many of the same applications as the Magnehelic gage where the greater accuracy, sensitivity, and higher and lower differential pressure ranges of the Magnehelic gage are not required.

Features

  • Jewel bearings provide virtually friction-free helix motion
  • Housing is molded from strong mineral and glass filled nylon.
  • Pointer stops of molded rubber prevent pointer over-travel without damage
  • Full view lens is removable and molded of tough acrylic
  • Combining High Accuracy, Compactness, Dependability, and Low Cost
  • See more on Amazon...

Brand: Dwyer   |   Manufacturer: Dwyer Instruments

Package Dimensions: 2.9 x 3.5 x 3.7 inches (7.4 x 8.9 x 9.4 cm)

Amazon Price: $53.90 | as of 11/20/2018(8:59am pst)
Availibility: Usually ships in 24 hours
List Price: $44.00

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #3

Door Pressure Gauge Push-Pull, 0-35 Lbs with Plastic Protective Tube

 PartNumber: DPG35PPT   |   Asin: B00V55YLI6

Push-Pull capability. Range is from 0-35 Pounds Door Pressure Gauge Push-Pull instrument design specifically to measure force. This instrument is capable of measuring the entire range of forces found in servicing interior and exterior doors. OPERATING INSTRUCTIONS Set the top (small) o-ring located on the plunger rod on zero, down against the instrument's flange; or set the o-ring on the desired force. Holding the instrument firmly, press slowly against the door at a point approximately handle-high, and 30 inches away from the door's hinges. Read the amount of force required to open the door on the plunger scale closest to the bottom of the small o-ring. MEET ADA REQUIREMENTS The Americans with Disabilities Act requires that both interior and exterior doors of a building be handicapped accessible. Door Opening Force (4.1311 ADA AG). Exterior hinged doors:(Reserved) Interior hinged doors:5 lbs (22.2N) Sliding or folding doors:5 lbs (22.2N) Automatic/Power Assisted Doors:(4.13.12) Such doors shall not open to back check faster than 3 seconds and shall require no more than 15 lbs (66.6N) to stop door movement. If a power assisted door is used, its door-opening force shall comply with 4.13.11 and its closing shall conform to the requirements in ANSI A156.19-1984. Plastic Protective Tube for Door Pressure Gauge. Size:8" long 7/8" diameter Includes: One Door Pressure Gauge Push-Pull, 0-35 Lbs One Plastic Protective Tube

Features

  • Range is from 0-35 Pounds
  • Door Pressure Gauge Push-Pull instrument design specifically to measure force.
  • capable of measuring the entire range of forces found in servicing interior and exterior doors
  • Meets ADA requirements
  • Includes: One Door Pressure Gauge Push-Pull, 0-35 Lbs and One Plastic Protective Tube
  • See more on Amazon...

Brand: TechnologyLK   |   Manufacturer: TechnologyLK

Amazon Price: $61.95 | as of 11/20/2018(8:59am pst)
Availibility: Usually ships in 4-5 business days
List Price: $61.95

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #4

New TK9A Backflow Test Kit 3 Valve Equipped with Free Line Pressure Gauge

 Ean: 7426928250441   |    PartNumber: tk9a   |   Asin: B07H1XP2SG

Watts TK9A backflow test kit equipped with a FREE Line Pressure Gauge. The Watts TK9A backflow test kit is used by certified backflow testers for testing all makes, models and sizes backflow preventer assemblies, including irrigation, domestic, isolation, containment and fire. The Watts TK9A backflow test kit ships fully assembled and with everything needed to start testing right away: hoses, adapters, calibration certificate and carrying case. Try it FREE for 30 days. You have nothing to lose - Love it or Leave it with our 30-Day Money Back Guarantee...5 Year Warranty...FREE Shipping and FREE Returns...In stock - ships in 1 day...Calibration certificate valid for one year... 3-valve backflow test kit for testing the following domestic, irrigation and fire-line backflow preventer assemblies: Reduced Pressure Zone (RPZ)...Double Check Valve (DC)...Pressure Vacuum Breaker (PVB)...Spill-resistant Pressure Vacuum Breaker (SPVB)...Reduced Pressure Detector Assembly (RPDA)...Double Check Detector Assembly (DCDA)...Standard 3-valve configuration (high, low, bypass)...4.5" Differential Pressure Gauge; scale: 0 -15 PSID..Equipped with FREE Line Pressure Gauge for recording system pressure, now required by most water purveyors; scale: 0-160 PSI...Full set test cock adapters: (3) 1/8" (3) 1/4" (3) 1/2" (total of 9)...Full set 36" Backflow Test Hoses: (3) color-coded (red, yellow and blue) with ergonomic knurled swivel couplings for easy on and off without tools...Standard operating 3-valve procedure capable of all test procedures... Maximum Working Temperature: 210 F...Maximum Working Pressure: 175 PSI...Ships fully assembled with calibration certificate valid for 1 year - start testing right out of the Aluminum, foam-lined Instrument Carrying Case...Try it FREE For 30 Days. This might change your mind. The Watts TK9A comes with a 30-Day Money Back Guarantee, if you don't love it, return it - no sweat, we'll even pay your return shipping!

Features

  • Watts TK9A Backflow Test Kit with FREE Line Pressure Gauge
  • Equipped with FREE Line Pressure Gauge, a $50 Value!
  • Everything included to start testing right away
  • FREE Instrument Carrying Case, Adapters and Hoses
  • FREE Calibration Certificate Valid for 1 YR
  • See more on Amazon...

Brand: TK9A   |   Manufacturer: Watts TK9A

Package Dimensions: 5.08 x 9.57 x 12.4 inches (12.9 x 24.3 x 31.5 cm)

Amazon Price: $569.99 | as of 11/20/2018(8:59am pst)
Availibility: Usually ships in 24 hours
List Price: $569.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #5

Dwyer Minihelic II Series 2-5000 Differential Pressure Gauge, Range 0-40"WC

Model: 2-5040   |    Mpn: 2-5040   |    PartNumber: 2-5040   |   Asin: B009PC6IOQ

Combining clean design, small size and low cost with enough accuracy for all but the most demanding applications our Minihelic II gage offers the latest in design features for a dial type differential pressure gage. It is our most compact gage but is easy to read and can safely operate at total pressures up to 30 psig. The Minihelic II gage is designed for panel mounting in a single 2-5/8" diameter hole. Standard pressure connections are barbed fittings for 3/16" ID tubing; optional 1/8" male NPT connections are also available. Over-pressure protection is built into the Minihelic II gage by means of a blow-out membrane molded in conjunction with the diaphragm. Accidental over-ranging up to the rated total pressure will not damage the gage. With removable lens and rear housing, the gage may be easily serviced at minimum cost. With the housing molded from mineral and glass filled nylon and the lens molded from acrylic, the gage will withstand rough use and exposure as well as high total pressure. The 5% accuracy and low cost of the Minihelic II gage make it well-suited for a wide variety of OEM and user applications. OEM applications include cabinet air purging, medical respiratory therapy equipment, air samplers, laminar flow hoods, and electronic air cooling systems. As an air filter gage, the Minihelic II gage finds many end use applications on large stationary engines, compressors, ventilators, and air handling units. The Minihelic II gage is suitable for many of the same applications as the Magnehelic gage where the greater accuracy, sensitivity, and higher and lower differential pressure ranges of the Magnehelic gage are not required.

Features

  • Jewel bearings provide virtually friction-free helix motion
  • Housing is molded from strong mineral and glass filled nylon.
  • Pointer stops of molded rubber prevent pointer over-travel without damage
  • Full view lens is removable and molded of tough acrylic
  • Combining High Accuracy, Compactness, Dependability, and Low Cost
  • See more on Amazon...

Brand: Dwyer   |   Manufacturer: Dwyer Instruments

Package Dimensions: 2.9 x 3.7 x 3.7 inches (7.4 x 9.4 x 9.4 cm)

First Available: 2017-05-15

Amazon Price: $51.90 | as of 11/20/2018(8:59am pst)
Availibility: Usually ships in 1 to 3 months
List Price: $63.30

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #6

Door Pressure Gauge, 0-35 Lbs with Plastic Protective Tube - 3 Pack

 PartNumber: DPG35T-3   |   Asin: B00V55SNLM

Range is from 0-35 Pounds Door Pressure Gauge instrument design specifically to measure force. OPERATING INSTRUCTIONS Set the top (small) o-ring located on the plunger rod on zero, down against the instrument's flange; or set the o-ring on the desired force. Holding the instrument firmly, press slowly against the door at a point approximately handle-high, and 30 inches away from the door's hinges. Read the amount of force required to open the door on the plunger scale closest to the bottom of the small o-ring. MEET ADA REQUIREMENTS The Americans with Disabilities Act requires that both interior and exterior doors of a building be handicapped accessible. Door Opening Force (4.1311 ADAAG). Exterior hinged doors:(Reserved) Interior hinged doors:5 lbs (22.2N) Sliding or folding doors:5 lbs (22.2N) Automatic/Power Assisted Doors:(4.13.12) Such doors shall not open to back check faster than 3 seconds and shall require no more than 15 lbs (66.6N) to stop door movement. If a power assisted door is used, its door-opening force shall comply with 4.13.11 and its closing shall conform to the requirements in ANSI A156.19-1984. Plastic Protective Tube for Door Pressure Gauge. Size:8" long 7/8" diameter Includes: Three Door Pressure Gauge, 0-35 Lbs Three Plastic Protective Tube

Features

  • Range is from 0-35 Pounds
  • Door Pressure Gauge instrument design specifically to measure force.
  • Meets ADA requirements
  • Three Door Pressure Gauge, 0-35 Lbs
  • Three Plastic Protective Tube
  • See more on Amazon...

Brand: TechnologyLK   |   Manufacturer: TechnologyLK

Amazon Price: $84.95 | as of 11/20/2018(8:59am pst)
Availibility: Usually ships in 4-5 business days
List Price: $84.95

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #7

Dwyer Series DM-2000 Differential Pressure Transmitter with LCD, Black Background, 0.5-0-0.5"WC

Model: DM-2013-LCD   |    Mpn: DM-2013-LCD   |    Ean: 0094704466460   |    PartNumber: DM-2013-LCD   |   Asin: B009PAM6Q2

The Dwyer Series DM-2000 Differential Pressure Transmitter senses the pressure of air and compatible gases and sends a standard 4-20 mA output signal. The DM-2000 housing is specifically designed to mount in the same diameter cutout as a standard Magnehelic gage. A wide range of models are available factory calibrated to specific ranges. Pressure connections are inherent to the glass filled plastic molded housing making installation quick and easy. Digital push-button zero and span simplify calibration over typical turn-potentiometers. An optional 3.5 digit LCD shows process and engineering units. A single bush button allows field selection of 4 to 6 engineering units depending on range.

Features

  • Air and non-combustible, compatible gases.
  • Consult Factory.
  • Digital push-button zero and span.
  • Screw-type terminal block.
  • Mounting orientation Vertical
  • See more on Amazon...

Brand: Dwyer   |   Manufacturer: Dwyer Instruments

Package Dimensions: 2.7 x 5.4 x 5.9 inches (6.9 x 13.7 x 15.0 cm)

Amazon Price: $119.90 | as of 11/20/2018(8:59am pst)
Availibility:
List Price: $112.00

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #8

Door Pressure Gauge Push-Pull, 0-35 Lbs with Plastic Protective Tube - 3 Pack

 PartNumber: DPG35PPT-3   |   Asin: B00V561N40

Push-Pull capability. Range is from 0-35 Pounds Door Pressure Gauge Push-Pull instrument design specifically to measure force. This instrument is capable of measuring the entire range of forces found in servicing interior and exterior doors. OPERATING INSTRUCTIONS Set the top (small) o-ring located on the plunger rod on zero, down against the instrument's flange; or set the o-ring on the desired force. Holding the instrument firmly, press slowly against the door at a point approximately handle-high, and 30 inches away from the door's hinges. Read the amount of force required to open the door on the plunger scale closest to the bottom of the small o-ring. MEET ADA REQUIREMENTS The Americans with Disabilities Act requires that both interior and exterior doors of a building be handicapped accessible. Door Opening Force (4.1311 ADA AG). Exterior hinged doors:(Reserved) Interior hinged doors:5 lbs (22.2N) Sliding or folding doors:5 lbs (22.2N) Automatic/Power Assisted Doors:(4.13.12) Such doors shall not open to back check faster than 3 seconds and shall require no more than 15 lbs (66.6N) to stop door movement. If a power assisted door is used, its door-opening force shall comply with 4.13.11 and its closing shall conform to the requirements in ANSI A156.19-1984. Plastic Protective Tube for Door Pressure Gauge. Size:8" long 7/8" diameter Includes: Three Door Pressure Gauge Push-Pull, 0-35 Lbs Three Plastic Protective Tube

Features

  • Range is from 0-35 Pounds
  • Door Pressure Gauge Push-Pull instrument design specifically to measure force.
  • capable of measuring the entire range of forces found in servicing interior and exterior doors
  • Meets ADA requirements
  • Includes: Three Door Pressure Gauge Push-Pull, 0-35 Lbs and Three Plastic Protective Tube
  • See more on Amazon...

Brand: TechnologyLK   |   Manufacturer: TechnologyLK

Amazon Price: $174.95 | as of 11/20/2018(8:59am pst)
Availibility: Usually ships in 4-5 business days
List Price: $174.95

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #9

ADA Door Pressure Gauge

 Ean: 0618028557989   |    PartNumber: PG   |   Asin: B0753L6C5F

2010 Americans with Disabilities Act Standards (ADAS) section 404.2.9 Door and Gate Opening Force: Fire doors shall have a minimum opening force allowable by the appropriate Administrative Authority. The force for pushing or pulling open a door or gate other than fire doors shall be as follows: 1. Interior hinged doors and gates: 5 pounds maximum. 2. Sliding or folding doors: 5 pounds maximum. These forces do not apply to the force required to retract latch bolts or disengage other devices that hold the door or gate in a closed position. Advisory 404.2.9 Door and Gate Opening Force. The maximum force pertains to the continuous application of force necessary to fully open a door, not the initial force needed to overcome the inertia of the door. It does not apply to the force required to retract bolts or to disengage other devices used to keep the door in a closed position. OPERATING INSTRUCTIONS : 1. Set the top (small) o-ring located on the plunger rod on zero, down against the instrument's flange; or set the o-ring on the desired force. 2. Holding the instrument firmly, press slowly against the door at a point approximately handle-high, and 30 inches away from the door's hinges. 3. Read the amount of force required to open the door on the plunger scale closest to the bottom of the small o-ring. A must have for determining ADA compliance! Protective Tube (plastic) for Universal Door Pressure Gauge. Size: 8" long 7/8" diameter Includes: One Universal Door Pressure Gauge, 0-35 Lbs One Plastic Protective Tube

Features

  • Easy To use Pocket Sized Tool With Case (Plastic)
  • Measures Opening Force to Open Doors
  • 0-35 LB Range
  • Easy To Read
  • Check for ADAS, ABAAS, ANSI A117.1, IBC, CBC, FAC, MAC, TAS, NYCBC, NJAC, OSSC, WSBC, OBC, VACC, NCSBC, NHABC, SBC, PBCC, IFC, NFPA compliance.
  • See more on Amazon...

Brand: CalCasp.Inc   |   Manufacturer: HMC

Package Dimensions: 2.3 x 8.9 x 11.1 inches (5.8 x 22.6 x 28.2 cm)

Amazon Price: $50.00 | as of 11/20/2018(8:59am pst)
Availibility: Usually ships in 1-2 business days
List Price: $50.00

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #10

TPI 621 Dual Differential Input Manometer, 5 Digit LCD, +/-0.5 percent Accuracy, 0.01" H2O Resolution, +/-120" H2O Range

Model: 621   |    Mpn: 621   |    Ean: 0637623006210   |    PartNumber: 621   |   Asin: B004XW6ENI

High efficiency gas and oil fired furnaces along with condensing boilers require a manometer with 0.001 inches of water resolution to make proper adjustments. 0.001 inH2O resolution at less than 40 inH2O; 0.01 inH2O resolution over 40 inH2O. Temperature compensated to ensure repeatable measurements. Seven units of pressure: inH2O, mbar, KPa, PSI, mmH2O, mmHg, . Trim mode to stabilize readings. Auto power off after 20 minutes. +/- 0.2 percent accuracy. 300mbar over pressure. 32 to 104 degree F operating temperature. RoHS compliant.

Features

  • High efficiency gas and oil fired furnaces along with condensing boilers require a manometer with 0.001 inches of water resolution to make proper adjustments
  • 0.001 inH2O resolution at less than 40 inH2O; 0.01 inH2O resolution over 40 inH2O
  • Temperature compensated to ensure repeatable measurements
  • Seven units of pressure: inH2O, mbar, KPa, PSI, mmH2O, mmHg,
  • Trim mode to stabilize readings
  • See more on Amazon...

Brand: TPI   |   Manufacturer: Test Products International, Inc

Package Dimensions: 2.3 x 6.7 x 11.3 inches (5.8 x 17.0 x 28.7 cm)

Amazon Price: $179.96 | as of 11/20/2018(8:59am pst)
Availibility: Usually ships in 4-5 business days
List Price: $199.95 | Used Price: $87.01

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #11

Dwyer DigiMag Series DM-1000 Differential Digital Pressure Gauge, Range 0-100"WC

Model: DM-1112   |    Mpn: DM-1112   |    Ean: 0094713837350   |    PartNumber: DM-1112   |   Asin: B009P8VH78

The DigiMag Series DM-1000 Digital Differential Pressure and Flow Gages monitor the pressure of air and compatible gases just as its famous analog predecessor the Magnehelic Differential Pressure Gage. All models are factory calibrated to specific ranges. The 4-digit LCD can display readings in common English and metric units so conversions are not necessary. The simplified four button operation reduces set up time and simplifies calibration with its digital push button zero and span.

Features

  • Air and non-combustible, compatible gases.
  • Consult factory.
  • Glass filled plastic.
  • Removable terminal block for 16 to 26 AWG.
  • Cable gland for 0.114 to 0.250 (2.9 to 6.4 mm) diameter cable.
  • See more on Amazon...

Brand: Dwyer   |   Manufacturer: Dwyer Instruments

Package Dimensions: 3.6 x 6.6 x 7.6 inches (9.1 x 16.8 x 19.3 cm)

Amazon Price: $115.00 | as of 11/20/2018(8:59am pst)
Availibility:
List Price: $115.00

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #12

Dwyer Series DM-2000 Differential Pressure Transmitter with LCD, Black Background, 0.25-0-0.25"WC

Model: DM-2012-LCD   |    Mpn: DM-2012-LCD   |    Ean: 0094704495712   |    PartNumber: DM-2012-LCD   |   Asin: B009PAM608

The Dwyer Series DM-2000 Differential Pressure Transmitter senses the pressure of air and compatible gases and sends a standard 4-20 mA output signal. The DM-2000 housing is specifically designed to mount in the same diameter cutout as a standard Magnehelic gage. A wide range of models are available factory calibrated to specific ranges. Pressure connections are inherent to the glass filled plastic molded housing making installation quick and easy. Digital push-button zero and span simplify calibration over typical turn-potentiometers. An optional 3.5 digit LCD shows process and engineering units. A single bush button allows field selection of 4 to 6 engineering units depending on range.

Features

  • Air and non-combustible, compatible gases.
  • Consult Factory.
  • Digital push-button zero and span.
  • Screw-type terminal block.
  • Mounting orientation Vertical
  • See more on Amazon...

Brand: Dwyer   |   Manufacturer: Dwyer Instruments

Package Dimensions: 3.1 x 5.4 x 5.8 inches (7.9 x 13.7 x 14.7 cm)

Amazon Price: $111.99 | as of 11/20/2018(8:59am pst)
Availibility: Usually ships in 24 hours
List Price: $112.00

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #13

8Pcs G326 Car Bicycle Petrol Gas Engine Cylinder Compressor Pressure Tester Gauge Multi Function Engine Repair Diagnostic Tool Compression Tester Set Test Set

 Ean: 0792172947640   |    PartNumber: GOTOTOPefsgxo94at   |   Asin: B07FZV9K89


Specifications:
Condition: 100% Brand New
Material: Copper, Rubber, Plastic
Gauge Color: Black
Thread Color: Gold
Case Color: Red
Test Pressure: 0 to 300 psi, 0- 21 kg/cm 2 (0-20 Bar)
4 Adapters: M10 x 1.0mm, M12 x 1.25mm, M14 x 1.25mm, M18 x 1.5mm
Hose Overall Length: 43cm / 17in
Pressure Tube Length: 15cm / 5.9in
Angled Pressure Tube Length: 16cm / 6.3in
Case Size: 26.5 * 19.5 * 5cm / 10.4 * 7.7 * 2in
Package Weight: Approx.1004g

Package List:
1 * Cylinder Pressure Gauge
4 * Adapters
2 * Pressure Tubes
1 * Hose
1 * Instruction
1 * Plastic Case

Features

  • Can be quickly set to your motor / car, get accurate readings in valves, piston rings, cylinder bores or head gaskets.
  • Manometer with double graduation ( 0 to 300 psi, 0- 21 kg / cm 2 ) and with rubber protection to prevent scratches
  • Pressure gauge diameter: 75mm, four thread size: M10 x 1.0mm, M12 x 1.25mm, M14 x 1.25mm, M18 x 1.5mm
  • Simply thread the spark plug adapter into the engines spark plug socket to check pressure and help identify engine performance issues
  • Drain valve with full copper nickel plating, anti-oxidation and corrosion. And with rubber protection to prevent scratches.
  • See more on Amazon...

Brand: GOTOTOP   |   Manufacturer: GOTOTOP

Item Dimensions: 1.57 x 3.94 x 5.91 inches (4.0 x 10.0 x 15.0 cm)   |   

Amazon Price: $44.05 | as of 11/20/2018(8:59am pst)
Availibility: Usually ships in 1-2 business days
List Price: $44.49

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #14

DIFFERENTIAL PRESSURE GAUGE 0-5 INCH W.C.

 Ean: 0758576892047   |    PartNumber: DPGJH20005X   |   Asin: B01N5PBTWU

DIFFERENTIAL PRESSURE GAUGE 0-5 INCH W.C.

Features

  • Differential pressure gauges indicates low air or non-corrosive gas pressures--either positive, negative (vacuum) or differential.
  • Material: Aluminum
  • Dimensions: 4-3/4 dia. X 2-3/16 deep
  • Accuracy: 2% of full scale at 70 F
  • Pressure Rating: 15 PSI
  • See more on Amazon...

Brand: JH Gauge   |   Manufacturer: JH Gauge

Amazon Price: $62.99 | as of 11/20/2018(8:59am pst)
Availibility: Usually ships in 24 hours
List Price: $62.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #15

Door Pressure Gauge, 0-35 Lbs with Plastic Protective Tube

 PartNumber: DPG35T   |   Asin: B00V55NKYC

Range is from 0-35 Pounds Door Pressure Gauge instrument design specifically to measure force. OPERATING INSTRUCTIONS Set the top (small) o-ring located on the plunger rod on zero, down against the instrument's flange; or set the o-ring on the desired force. Holding the instrument firmly, press slowly against the door at a point approximately handle-high, and 30 inches away from the door's hinges. Read the amount of force required to open the door on the plunger scale closest to the bottom of the small o-ring. MEET ADA REQUIREMENTS The Americans with Disabilities Act requires that both interior and exterior doors of a building be handicapped accessible. Door Opening Force (4.1311 ADAAG). Exterior hinged doors:(Reserved) Interior hinged doors:5 lbs (22.2N) Sliding or folding doors:5 lbs (22.2N) Automatic/Power Assisted Doors:(4.13.12) Such doors shall not open to back check faster than 3 seconds and shall require no more than 15 lbs (66.6N) to stop door movement. If a power assisted door is used, its door-opening force shall comply with 4.13.11 and its closing shall conform to the requirements in ANSI A156.19-1984. Plastic Protective Tube for Door Pressure Gauge. Size:8" long 7/8" diameter Includes: One Door Pressure Gauge, 0-35 Lbs One Plastic Protective Tube

Features

  • Range is from 0-35 Pounds
  • Door Pressure Gauge instrument design specifically to measure force.
  • Meets ADA requirements
  • One Door Pressure Gauge, 0-35 Lbs
  • One Plastic Protective Tube
  • See more on Amazon...

Brand: TechnologyLK   |   Manufacturer: TechnologyLK

Package Dimensions: 0.71 x 0.71 x 8.31 inches (1.8 x 1.8 x 21.1 cm)

Amazon Price: $35.95 | as of 11/20/2018(8:59am pst)
Availibility: Usually ships in 4-5 business days
List Price: $35.95

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #16

Dwyer Series DM-2000 Differential Pressure Transmitter with LCD, Black Background, 0-5"WC

Model: DM-2007-LCD   |    Mpn: DM-2007-LCD   |    Ean: 0094704543437   |    PartNumber: DM-2007-LCD   |   Asin: B009PAMBXA

The Dwyer Series DM-2000 Differential Pressure Transmitter senses the pressure of air and compatible gases and sends a standard 4-20 mA output signal. The DM-2000 housing is specifically designed to mount in the same diameter cutout as a standard Magnehelic gage. A wide range of models are available factory calibrated to specific ranges. Pressure connections are inherent to the glass filled plastic molded housing making installation quick and easy. Digital push-button zero and span simplify calibration over typical turn-potentiometers. An optional 3.5 digit LCD shows process and engineering units. A single bush button allows field selection of 4 to 6 engineering units depending on range.

Features

  • Air and non-combustible, compatible gases.
  • Consult Factory.
  • Digital push-button zero and span.
  • Screw-type terminal block.
  • Mounting orientation Vertical
  • See more on Amazon...

Brand: Dwyer   |   Manufacturer: Dwyer Instruments

Package Dimensions: 3 x 5.3 x 6 inches (7.6 x 13.5 x 15.2 cm)

Amazon Price: $110.90 | as of 11/20/2018(8:59am pst)
Availibility:
List Price: $106.00

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #17

Dwyer Magnesense Series MS Differential Pressure Transmitter, Bidirectional Unit, 4-20 mA, Low Range 0.1, 0.25, 0.5"WC & 25, 50, 100 Pa, Wall Mount, LCD

Model: MS-021-LCD   |    Mpn: MS-021-LCD   |    PartNumber: MS-021-LCD   |   Asin: B009P9IF3G

The Series MS Magnesense Differential Pressure Transmitter is an extremely versatile transmitter for monitoring pressure and air velocity. This compact package is loaded with features such as: field selectable English or metric ranges, field upgradeable LCD display, adjustable dampening of output signal (with optional display) and the ability to select a square root output for use with Pitot tubes and other similar flow sensors. Along with these features, the magnetic sensing technology provides exceptional long term performance and enables the Magnesense transmitter to be the solution for a myriad of pressure and flow applications.

Features

  • Field Selectable Ranges in metric or English. Lowers stock and inventory requirements. You'll always have the right transmitter for every job.
  • Digital Push Button Zero and Span
  • Adjustable Digital Dampening smoothes out unstable pressure fluctuations common in air flow applications.
  • Field Selectable Air Velocity Mode for fan and blower applications.
  • Field Upgradeable LCD
  • See more on Amazon...

Brand: Dwyer   |   Manufacturer: Dwyer Instruments

Package Dimensions: 2.9 x 5.1 x 5.3 inches (7.4 x 13.0 x 13.5 cm)

Amazon Price: $135.50 | as of 11/20/2018(8:59am pst)
Availibility:
List Price: $135.50

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #18

Dwyer Magnesense Series MS Differential Pressure Transmitter, Positive Only Unit, 4-20 mA, High Range 1, 2, 5"WC & 250, 500, 1250 Pa, Wall Mount, LCD

Model: MS-111-LCD   |    Mpn: MS-111-LCD   |    PartNumber: MS-111-LCD   |   Asin: B009P9IHZW

The Series MS Magnesense Differential Pressure Transmitter is an extremely versatile transmitter for monitoring pressure and air velocity. This compact package is loaded with features such as: field selectable English or metric ranges, field upgradeable LCD display, adjustable dampening of output signal (with optional display) and the ability to select a square root output for use with Pitot tubes and other similar flow sensors. Along with these features, the magnetic sensing technology provides exceptional long term performance and enables the Magnesense transmitter to be the solution for a myriad of pressure and flow applications.

Features

  • Field Selectable Ranges in metric or English. Lowers stock and inventory requirements. You'll always have the right transmitter for every job.
  • Digital Push Button Zero and Span
  • Adjustable Digital Dampening smoothes out unstable pressure fluctuations common in air flow applications.
  • Field Selectable Air Velocity Mode for fan and blower applications.
  • Field Upgradeable LCD
  • See more on Amazon...

Brand: Dwyer   |   Manufacturer: Dwyer Instruments

Package Dimensions: 2.9 x 5.1 x 5.4 inches (7.4 x 13.0 x 13.7 cm)

Amazon Price: $120.00 | as of 11/20/2018(8:59am pst)
Availibility: Usually ships in 24 hours
List Price: $120.00

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon




Looking For Something Else? Search

Most Popular
New Releases

  1. Dwyer Capsuhelic Series 4000 Differential Pressure Gauge, Range 0-50"WC
  2. Dwyer Minihelic II Series 2-5000 Differential Pressure Gauge, Range 0-100 mm WC
  3. Door Pressure Gauge Push-Pull, 0-35 Lbs with Plastic Protective Tube
  4. New TK9A Backflow Test Kit 3 Valve Equipped with Free Line Pressure Gauge
  5. Dwyer Minihelic II Series 2-5000 Differential Pressure Gauge, Range 0-40"WC
  6. Door Pressure Gauge, 0-35 Lbs with Plastic Protective Tube - 3 Pack
  7. Dwyer Series DM-2000 Differential Pressure Transmitter with LCD, Black Background, 0.5-0-0.5"WC
  8. Door Pressure Gauge Push-Pull, 0-35 Lbs with Plastic Protective Tube - 3 Pack
  9. ADA Door Pressure Gauge
  10. TPI 621 Dual Differential Input Manometer, 5 Digit LCD, +/-0.5 percent Accuracy, 0.01" H2O Resolutio...

Most Wished For

  1. Dwyer Capsuhelic Series 4000 Differential Pressure Gauge, Range 0-50"WC
  2. Dwyer Minihelic II Series 2-5000 Differential Pressure Gauge, Range 0-100 mm WC
  3. Door Pressure Gauge Push-Pull, 0-35 Lbs with Plastic Protective Tube
  4. New TK9A Backflow Test Kit 3 Valve Equipped with Free Line Pressure Gauge
  5. Dwyer Minihelic II Series 2-5000 Differential Pressure Gauge, Range 0-40"WC
  6. Door Pressure Gauge, 0-35 Lbs with Plastic Protective Tube - 3 Pack
  7. Dwyer Series DM-2000 Differential Pressure Transmitter with LCD, Black Background, 0.5-0-0.5"WC
  8. Door Pressure Gauge Push-Pull, 0-35 Lbs with Plastic Protective Tube - 3 Pack
  9. ADA Door Pressure Gauge
  10. TPI 621 Dual Differential Input Manometer, 5 Digit LCD, +/-0.5 percent Accuracy, 0.01" H2O Resolutio...

Most Gifted

  1. Dwyer Capsuhelic Series 4000 Differential Pressure Gauge, Range 0-50"WC
  2. Dwyer Minihelic II Series 2-5000 Differential Pressure Gauge, Range 0-100 mm WC
  3. Door Pressure Gauge Push-Pull, 0-35 Lbs with Plastic Protective Tube
  4. New TK9A Backflow Test Kit 3 Valve Equipped with Free Line Pressure Gauge
  5. Dwyer Minihelic II Series 2-5000 Differential Pressure Gauge, Range 0-40"WC
  6. Door Pressure Gauge, 0-35 Lbs with Plastic Protective Tube - 3 Pack
  7. Dwyer Series DM-2000 Differential Pressure Transmitter with LCD, Black Background, 0.5-0-0.5"WC
  8. Door Pressure Gauge Push-Pull, 0-35 Lbs with Plastic Protective Tube - 3 Pack
  9. ADA Door Pressure Gauge
  10. TPI 621 Dual Differential Input Manometer, 5 Digit LCD, +/-0.5 percent Accuracy, 0.01" H2O Resolutio...

Top Selling

  1. Dwyer Capsuhelic Series 4000 Differential Pressure Gauge, Range 0-50"WC
  2. Dwyer Minihelic II Series 2-5000 Differential Pressure Gauge, Range 0-100 mm WC
  3. Door Pressure Gauge Push-Pull, 0-35 Lbs with Plastic Protective Tube
  4. New TK9A Backflow Test Kit 3 Valve Equipped with Free Line Pressure Gauge
  5. Dwyer Minihelic II Series 2-5000 Differential Pressure Gauge, Range 0-40"WC
  6. Door Pressure Gauge, 0-35 Lbs with Plastic Protective Tube - 3 Pack
  7. Dwyer Series DM-2000 Differential Pressure Transmitter with LCD, Black Background, 0.5-0-0.5"WC
  8. Door Pressure Gauge Push-Pull, 0-35 Lbs with Plastic Protective Tube - 3 Pack
  9. ADA Door Pressure Gauge
  10. TPI 621 Dual Differential Input Manometer, 5 Digit LCD, +/-0.5 percent Accuracy, 0.01" H2O Resolutio...



Main Categories

Home & Garden


Home Improvement


Electronics


Office


Car & Automotive


Sporting Goods


Toys and Hobby


Health & Personal Care


Beauty Supplies


Fashion


Industrial


Related Categories

Abrasive & Finishing


Cutting Tools


Fasteners


Filtration


Commercial Door Products


Hydraulics, Pneumatics & Plumbing


Industrial Hardware


Industrial Tools


Food Services


Janitorial & Sanitation


Lab Equipment


Material Handling


Occupational Health


Packaging & Shipping


Power Transmission


Dental Supplies


Medical Supplies


Raw Materials


Retail Fixtures & Equipment


Tapes, Adhesives & Sealants


Test, Measure & Inspect


Robotics, 3D Printing & Science Education


Industrial Electrical



We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
Certain content that appears on GistGear.com comes from Amazon services llc. This content is provided 'as is' and is subject to change or removal at any time.
Any price and availability information displayed on Amazon.com at the time of purchase will apply to the purchase of this product.
Amazon product prices and availability are accurate as of the date/time indicated and are subject to change.