Frontpage > Industrial > Test, Measure & Inspect > Function Generators

Best Function Generators - Buying Guide

Last Updated: 01/17/2019

Share on

Bestselling Function Generators on Amazon

  1. 4-20mA Generator, DROK Adjustable Signal Generator, DC 0-10V 0/4-20mA Current Voltage Analog Simulat...
  2. Signal Generator DIY Kit, KKmoon XR2206 High Precision Function Signal Generator DIY Kit Sine/Triang...
  3. Koolertron Upgraded 15MHz DDS Signal Generator Counter,High Precision Dual-channel Arbitrary Wavefor...
  4. XR2206 Function Generator - kuman Updated XR2206 DIY Kit Signal Generator with Screwdriver and Jumpe...
  5. Koolertron Upgraded 60MHz DDS Signal Generator Counter,High Precision Dual-channel Arbitrary Wavefor...
  6. Siglent SDG1025 Function/Arbitrary Waveform Generator, 25MHz, 125MSa/s Sample Rate
  7. Signal Generator, KKmoon High Precision Digital DDS Dual-Channel Signal Source Generator Arbitrary W...
  8. Yosoo 1HZ-500KHz DDS Function Signal Generator Module Sine+Triangle+Square Wave
  9. Signal Detector, KKmoon High Precision Digital DDS Dual-channel Signal Source Generator Arbitrary Wa...
  10. 4-20mA Signal Generator, DROK 4 Digits Constant Current Source Generator with Adjustable Digital Pot...

  #1

4-20mA Generator, DROK Adjustable Signal Generator, DC 0-10V 0/4-20mA Current Voltage Analog Simulator for Value Adjusting PLC Panel LED Testing, Transmitter, Output Simulation

 PartNumber: 300482   |   Asin: B071NLGP6L

Product Features:
By rotating a multi-cycle precise potentiometer, this product can generate 0/4 - 20mA current signal and 0-10V voltage signal,
which can used as signal generator, valve adjustment, inverter control, PLC debugging, panel debugging, LED testing, simulating the output of transmitter.

Product Parameters:
Working voltage: DC24V
Input signal: Potentiometer
Output signal: 0/4-20mA or 0-10V
Display accuracy: Current: 0.1mA; Voltage: 0.01V
Dimension: 100*68*38mm

Debugging Procedures:
A. Current display calibration
Clockwise rotating the multi-cycle potentiometer to the maximum, switching the display switch to the right and then using a multimeter to test the actual value of the output current.
At this time, you can adjust the current display adjusting potentiometer to make the display value equal to the actual output value.

B. Voltage display calibration
Clockwise rotating the multi-cycle potentiometer to the maximum, switching the display switch to the left and then using a multimeter to test the actual value of the output voltage.
At this time, you can adjust the voltage display adjusting potentiometer to make the display value equal to the actual output value.

Package Includes:
1* Signal Generator

Features

  • AMP & VOLT DUAL SIGNAL GENERATOR: Multifunctional DROK signal generator kit is able to generate ampere & voltage by one module, which generate 0/4 - 20mA current signal and 0-10V voltage signal just by rotating a multi-cycle precise potentiometer, simple and handy.
  • CLEAR LED DISPLAY: Our 4-20ma signal generator has bright and clear 3-digit LED digital display screen, which can be used to monitor the output current and voltage. You just need to push the switch below the monitor easy to switch the display.
  • AMP & VOLT DISPLAY CALIBRATION: There are current and voltage display calibrating potentiometer on the back of the module. If the display is accurate, you can calibrate the display value of current voltage by yourself.
  • WIDE APPLICATION: Our signal adapter can be used as signal generator, valve adjustment, inverter control, PLC debugging, panel debugging, LED testing, simulating the output of transmitter.
  • See more on Amazon...

Brand: DROK   |   Manufacturer: DROK

Package Dimensions: 2.83 x 5.43 x 5.75 inches (7.2 x 13.8 x 14.6 cm)

Amazon Price: $28.99 | as of 01/17/2019(2:44pm pst)
Availibility: Usually ships in 24 hours
List Price: $28.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #2

Signal Generator DIY Kit, KKmoon XR2206 High Precision Function Signal Generator DIY Kit Sine/Triangle/Square Output 1Hz-1MHz Adjustable Frequency

Model: MP26174598   |    Mpn: TX773899070   |    Ean: 0713893274877   |    PartNumber: TX773899070   |   Asin: B01HM70CMY

This signal generator DIY kit is professional product to generate sine/triangle/square wave. It's a DIY kit for you to weld and install. Specifications Voltage Supply: 9-12V DC Input Waveforms: Square, Sine & Triangle Impedance: 600 Ohm + 10% Frequency: 1Hz-1MHz SINE WAVE Amplitude: 0-3V at 9V DC Input Distortion: Less than 1% (at 1KHz) Flatness: +0.05dB 1Hz - 100kHz SQUARE WAVE Amplitude: 8V (no load) at 9V DC Input Rise Time: Less than 50ns (at 1KHz) Fall Time: Less than 30ns (at 1KHz) Symmetry: Less than 5% (at 1KHz) TRIANGLE WAVE Amplitude: 0-3V at 9V DC Input Linearity: Less than 1% (up to 100KHz) 10mA Package Size: Approx. 12 * 8 * 2cm / 4.72 * 3.15 * 0.8in Package Weight: 69g / 2.46oz What is in the box 1 * Signal Generator DIY Kit 1 * User Manual(English)

Features

  • High resolution, can generate sine/triangle/square waveforms.
  • Frequency range: 1Hz-1MHz.Adjustable frequency and amplitude.
  • Frequency adjustment features coarse tuning and fine tuning.All are through hole components, easy for installation.
  • Wide power supply range, use 9-12V external power or 9V battery(NOT Included).
  • This product belongs to KKMOON. If you find other merchants selling our exclusive brand, it is a counterfeit product, please don't be fooled and contact us in time.
  • See more on Amazon...

Brand: KKmoon   |   Manufacturer: KKmoon

Package Dimensions: 0.87 x 5.43 x 6.14 inches (2.2 x 13.8 x 15.6 cm)

Amazon Price: $13.99 | as of 01/17/2019(2:44pm pst)
Availibility: Usually ships in 24 hours
List Price: $13.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #3

Koolertron Upgraded 15MHz DDS Signal Generator Counter,High Precision Dual-channel Arbitrary Waveform Function Generator Frequency Meter 200MSa/s (15MHz)

Model: GH-CJDS66   |    Mpn: GH-CJDS66   |    Ean: 0886085651487   |    PartNumber: GH-CJDS66   |   Asin: B07211YWMK

Advantage:
High frequency precision up to 10-6 orders of magnitude.
Full range of 0.01 Hz frequency resolution.
Minimum amplitude resolution can be up to 1mV.
Duty cycle of each channel can be adjusted separately. Precision can be 0.1%.

Frequency Characteristic:
Normal Modes & Square & Triangle Wave: 0~15MHz
Sawtooth & Arbitrary & TTL Digital Signal Wave: 0~6MHz
Square rise time: 30nS
Frequency accuracy: 20ppm 10-6
Frequency stability: 1ppm 10-6/3h

Waveform Characteristic:
Waveform: Sine, Square, Triangle, Pulse (duty-cycle correction), Partia Sine, CMOS, DC level, Half-wave, Full-Wave, Pos-Ladder, Neg-Ladder, Noise, Exponential Rise, Exponential Fall, Tone, Sinc Pulse, Lorentz Pulse, and 60 kinds user defined waveform.

Output Characteristics:
Amplitude resolution: 1mV
Amplitude stability: 0.5%/5 h
Amplitude flatness: 5%( 10MHz)

Frequency Meter Function:
Frequency measurement range: 1Hz~100MHz
Measurement accuracy: Gate time continuously adjusted between 0.01S~10s

Counter Function:
Counting region: 0-4294967295
Coupled mode: 2kinds Coupling modes, DC and AC
Counting mode: Manual operation

Package Included:
1 x DDS Signal Generator
1 x USB Cable
1 x Power Adapter
2 x Q9 Cable
1 x CD

Features

  • Arbitrary Waveform Generator adopts large scale FPGA integrated circuit and high-speed MCU microprocessor. The internal circuit adopts the active crystal oscillator as the benchmark. So the signal stability is greatly strengthened.
  • Using Dual-channel DDS signal and TTL electric level output to generate precise, stable, low distortion output signal. includes Sine wave, Square wave, Triangle wave, Saw toothwave, Pulse wave, white noise, user-defined waveform etc. each channel can be independently set the parameters.
  • With linear sweep(Max. up to 999.9s) and logarithmic frequency sweep functions.Has a frequency measurement, period measurement, positive and negative pulse width measurement and counting function.
  • Storage feature: You can store 99 groups instrument state parameters set by the user, can be called up to Reproduce.The frequency output of Sine wave can be up to 15MHz. 200MSa/s sampling rate. It has 60 positions for saving user-defined waveform. Waveform Length of each one is 2048 and vertical resolution is 14 bits
  • This Signal Generator is the ideal instrument for electronic engineering, laboratories, production lines, teaching and scientific research.
  • See more on Amazon...

Brand: Koolertron   |   Manufacturer: Koolertron

Package Dimensions: 6.7 x 8.4 x 11.8 inches (17.0 x 21.3 x 30.0 cm)

Amazon Price: $99.88 | as of 01/17/2019(2:44pm pst)
Availibility: Usually ships in 24 hours
List Price: $99.88

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #4

XR2206 Function Generator - kuman Updated XR2206 DIY Kit Signal Generator with Screwdriver and Jumper Wires Cable - Sine Triangle Square Output 1Hz-1MHz Adjustable Frequency Amplitude K76

 PartNumber: K76-US   |   Asin: B06Y5MWJ6L

Kuman is committed to offer more qualified products to our customers.
This is a updated XR2206 DIY Kit Signal Generator with the new added 3.0mm Phillips Screwdriver and DuPont wire cables, much more convenient to install.
Any question, just feel free to contact us, we offer friendly customer service.

Specifications:

Voltage Supply: 9-12V DC Input
Waveforms: Square, Sine & Triangle
Impedance: 600 Ohm + 10%
Frequency: 1Hz-1MHz
screwdriver length: 100MM

SINE WAVE

Amplitude: 0-3V at 9V DC Input
Distortion: Less than 1% (at 1KHz)
Flatness: +0.05dB 1Hz - 100kHz

SQUARE WAVE

Amplitude: 8V (no load) at 9V DC Input
Rise Time: Less than 50ns (at 1KHz)
Fall Time: Less than 30ns (at 1KHz)
Symmetry: Less than 5% (at 1KHz)
TRIANGLE WAVE
Amplitude: 0-3V at 9V DC Input
Linearity: Less than 1% (up to 100KHz) 10mA

Package Includes:
1 * Kuman Signal Generator DIY Kit
1 * 10P male to male Jumper Wires
1 * 3.0mm Phillips screwdriver(100mm length)
1 * English User Manual

Features

  • Kuman XR2206 Great Function Signal Generator DIY Kit add the Screwdriver and 10p male to male Jumper cables which makes the product easier to install.
  • High Precision, can generate sine/triangle/square waveforms.
  • Output frequency range: 1Hz-1MHz and Adjustable frequency and amplitude.
  • Wide power supply range, use 9-12V external power or 9V battery(NOT Included).
  • This is a DIY kit with All are through hole components,easily assemble the Function Generator by yourself.
  • See more on Amazon...

Brand: Kuman   |   Manufacturer: Kuman

Package Dimensions: 1.57 x 4.17 x 5.91 inches (4.0 x 10.6 x 15.0 cm)

Amazon Price: $15.85 | as of 01/17/2019(2:44pm pst)
Availibility: Usually ships in 24 hours
List Price: $20.00

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #5

Koolertron Upgraded 60MHz DDS Signal Generator Counter,High Precision Dual-channel Arbitrary Waveform Function Generator Frequency Meter 200MSa/s (60MHz)

Model: GH-CJDS66   |    Mpn: GH-CJDS66   |    Ean: 0886085651807   |    PartNumber: GH-CJDS66   |   Asin: B073P6TKQC

Advantage:
High-frequency precision up to 10-6 orders of magnitude.
Full range of 0.01 Hz frequency resolution.
Minimum amplitude resolution can be up to 1mV.
Duty cycle of each channel can be adjusted separately. Precision can be 0.1%.

Frequency Characteristic:
Sine frequency range: 0~60MHz
Square & Triangle Wave: 0~15MHz
Pulse & Arbitrary & TTL Digital Signal Wave: 0~6MHz
Square rise time: 15nS
Pulse width adjustment range: 30nS~4000S
Frequency accuracy: 20ppm 10-6
Frequency stability: 1ppm 10-6/3h

Waveform Characteristic:
Waveform: Sine, Square, Triangle, Pulse (duty-cycle correction), Partial Sine, CMOS, DC level, Half-wave, Full-Wave, Pos-Ladder, Neg-Ladder, Noise, Exponential Rise, Exponential Fall, Tone, Sinc Pulse, Lorentz Pulse, and 60 kinds user-defined waveform.

Output Characteristics:
Amplitude resolution: 1mV
Amplitude stability: 0.5%/5 h
Amplitude flatness: 5%( 10MHz)

Frequency Meter Function:
Frequency measurement range: 1Hz~100MHz
Measurement accuracy: Gate time continuously adjusted between 0.01S~10s

Counter Function:
Counting region: 0-4294967295
Coupled mode: 2kinds Coupling modes, DC and AC
Counting mode: Manual operation

Package Included:

1 x DDS Signal Generator
1 x USB Cable
1 x Power Adapter
2 x Q9 Cable
1 x CD

Features

  • Arbitrary Waveform Generator adopts large scale FPGA integrated circuit and high speed MCU microprocessor. The internal circuit adopts active crystal oscillator as benchmark. So the signal stability is greatly strengthened.
  • Using Dual-channel DDS signal and TTL electric level output to generate precise, stable, low distortion output signal. includes Sine wave, Square wave, Triangle wave, Sawtooth wave, Pulse wave, white noise, user-defined waveform etc. each channel can be independently set the parameters.
  • With linear sweep(Max. up to 999.9s) and logarithmic frequency sweep functions.Has a frequency measurement, period measurement, positive and negative pulse width measurement and counting function.
  • Storage feature: You can store 99 groups instrument state parameters set by the user, can be called up to Reproduce. Frequency output of Sine wave can be up to 60MHz. 200MSa/s sampling rate. It has 60 positions for saving user-defined waveform. Waveform Length of each one is 2048 and vertical resolution is 14 bits
  • This Signal Generator is the ideal instrument for electronic engineering, laboratories, production lines, teaching and scientific research.
  • See more on Amazon...

Brand: Koolertron   |   Manufacturer: Koolertron

Package Dimensions: 4.02 x 8.39 x 9.88 inches (10.2 x 21.3 x 25.1 cm)

Amazon Price: $139.99 | as of 01/17/2019(2:44pm pst)
Availibility: Usually ships in 24 hours
List Price: $139.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #6

Siglent SDG1025 Function/Arbitrary Waveform Generator, 25MHz, 125MSa/s Sample Rate

Model: SDG1025   |    Mpn: SDG1025   |    Ean: 0519805775346   |    PartNumber: SDG1025   |   Asin: B00GQNNVH4

The SIGLENT is siglent's latest addition to an already powerful line of arb/function generators.

Features

  • Apply DDS technology, double output, adjustable phase, the highest output frequency is 25MHz
  • 125MSa/s sample rate, 14bit vertical resolution, 16Kpts wave length
  • Output 5 types of standard waveform, internally installed 48 types of waveform
  • Abundant modulation function, sweep-frequency output, pulse train output
  • Can connect to SDS1000 series digital oscilloscope perfectly, and support remote command control
  • See more on Amazon...

Brand: Siglent   |   Manufacturer: Siglent Technologies

Package Dimensions: 7.75 x 13.5 x 14.75 inches (19.7 x 34.3 x 37.5 cm)

Amazon Price: $319.00 | as of 01/17/2019(2:44pm pst)
Availibility: Usually ships in 24 hours
List Price: $359.00

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #7

Signal Generator, KKmoon High Precision Digital DDS Dual-Channel Signal Source Generator Arbitrary Waveform Frequency Meter 200MSa/s 25MHz

Model: Weight542g / 19.12oz   |    Mpn: B071HJ31WN   |    PartNumber: B071HJ31WN   |   Asin: B071HJ31WN

Specifications:
Frequency Range:Sine Wave
Normal Modes(Optional): 0.01Hz~6MHz / 0.01Hz~12MHz / 0.01Hz~20MHz / 0.01Hz~25MHz
Square Wave:0.01Hz~6MHz
Triangle Wave:0.01Hz~6MHz
Sawtooth Wave:0.01Hz~6MHz
Arbitrary Waveform0.01Hz~6MHz
TTL Digital Signal Wave:0.01Hz~6MHz
The Min. Frequency Resolution:10mHz
Amplitude Range(Peak to Peak):5mVp-p~20Vp-p
Output Impedance:50 (+/-10%)
Offset Range:-120%~120% (The ratio of bias voltage and signal amplitude)
Sine WaveHarmonic Arrived System40dBc(

Features

  • WAVEFORMS Can output arbitrary waveforms and conventional function waveforms(sine/triangle/square/sawtooth wave and TTL signal).All functions are digitally controlled, precise and stable.
  • DUAL-CHANNEL Dual-channel output, can work in sync, phase difference is adjustable.With linear sweep(Max. up to 999s) and logarithmic frequency sweep functions.
  • BUILT-IN ATTENUATOR Signal of both channels has built-in sophisticated -20dB attenuator in order to reach the minimum amplitude resolution 1mV.With 120% ~ + 120% DC bias function.
  • USB INTERFACE 4 TTL output(phase difference is adjustable).With USB interface, after the connection with PC, the PC can be used to control the instrument.
  • FUNCTION Has a frequency measurement, period measurement, positive and negative pulse width measurement, duty cycle measurements and counting function.
  • See more on Amazon...

Brand: KKmoon   |   Manufacturer: KKmoon

Item Dimensions: 2.75 x 6.9 x 7.67 inches (7.0 x 17.5 x 19.5 cm)   |   Package Dimensions: 4.09 x 8.82 x 10.59 inches (10.4 x 22.4 x 26.9 cm)

Amazon Price: $64.99 | as of 01/17/2019(2:44pm pst)
Availibility: Usually ships in 24 hours
List Price: $64.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #8

Yosoo 1HZ-500KHz DDS Function Signal Generator Module Sine+Triangle+Square Wave

Model: YS-W500   |    Mpn: YS-W500   |    Ean: 0702679611449   |    PartNumber: YS-W500   |   Asin: B00PQ05Z9A


Product description: Brand new and high quality

The main output waveform : sine wave and square-wave, triangle wave, sawtooth wave

Maximum output amplitude: 10Vpp (no-load)

Output impedance :50 10%

Dc bias: 10V (no-load)

Display: LCD1602
Resolution :1 Hz

power supply: DC 3.5-10V

Output frequency range: sine wave: 1Hz-500KHz Square-wave: 1 Hz - 20kHz (the valid range) Triangle wave :1 Hz - 20KHz (the valid range) Sawtooth wave :1 Hz ~ 20kHz (the valid range)

Package included:

1 Pcs * DDS Function Signal Generator

Features

  • The main output waveform : sine wave and square-wave, triangle wave, sawtooth wave
  • Maximum output amplitude: 10Vpp (no-load)
  • Output impedance :50 10%
  • Display: LCD1602
  • power supply: DC 3.5-10V
  • See more on Amazon...

Brand: Yosoo   |   Manufacturer: Yosoo

Package Dimensions: 2.2 x 4.6 x 5.9 inches (5.6 x 11.7 x 15.0 cm)

Amazon Price: $22.99 | as of 01/17/2019(2:44pm pst)
Availibility: Usually ships in 24 hours
List Price: $32.99 | Used Price: $21.38

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #9

Signal Detector, KKmoon High Precision Digital DDS Dual-channel Signal Source Generator Arbitrary Waveform Frequency Meter 200MSa/s 25MHz Signal Detector

 Ean: 0733180210395   |    PartNumber: B014KT3IT6   |   Asin: B014KT3IT6


Specifications
Normal Modes(Optional): 0.01Hz~25MHz
Square Wave: 0.01Hz~6MHz
Triangle Wave: 0.01Hz~6MHz
Sawtooth Wave: 0.01Hz~6MHz
Arbitrary Waveform: 0.01Hz~6MHz
TTL Digital Signal Wave: 0.01Hz~6MHz
Output Modulation: Frequency Sweep
The Min. Frequency Resolution: 10mHz
Amplitude Range(Peak to Peak
Offset Range: -120%~120% (The ratio of bias voltage and signal amplitude)
Bias Resolution: 1%
Phase Range: 0~359
Phase Resolution: 1
Sine Wave: Harmonic Arrived System 40dBc(

Features

  • Can output arbitrary waveforms and conventional function waveforms(sine/triangle/square/sawtooth wave and TTL signal).
  • All functions are digitally controlled, precise and stable.
  • Dual-channel output, can work in sync, phase difference is adjustable.
  • With linear sweep(Max. up to 999s) and logarithmic frequency sweep functions.
  • Signal of both channels has built-in sophisticated -20dB attenuator in order to reach the minimum amplitude resolution 1mV.
  • See more on Amazon...

Brand: KKmoon   |   Manufacturer: KKmoon

Package Dimensions: 4.09 x 8.82 x 11.81 inches (10.4 x 22.4 x 30.0 cm)

Amazon Price: $61.99 | as of 01/17/2019(2:44pm pst)
Availibility: Usually ships in 24 hours
List Price: $61.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #10

4-20mA Signal Generator, DROK 4 Digits Constant Current Source Generator with Adjustable Digital Potentiometer Knobs, Voltage, Current LED Display

 PartNumber: DR_300425   |   Asin: B07H75LQ6N

Technical Parameters:
-- Multi-ring (5 * 360) potentiometer knob operation, stepless fine adjustment, in response to the output immediately, no delay
-- Potentiometer to adjust the actual fineness of up to 0.01 mA
-- Power supply: DC12-30V,DC 12V or 24V, current 18mA, power port has a polarity protection, power reverse does not work, do not burn components.
-- 4-bit 0.36-inch LED, the display range: -1999-9999, can be set to the number of 0,1,2,3 decimal points
-- 20mA output: the maximum output current of 24mA.
-- 12V DC power supply: output load impedance range between 0-350 ohms
-- 24V DC power supply: output load impedance range between 0-800 Ohms
-- The test output is normal, you can use a multimeter (DC current file) short "4-20mA output" terminal value and the comparison shows that the multimeter readings are the same.
-- Easy to install, standard 7943 shell, panel size: 79mm * 43mm * 25mm, hole size: 76.5mm * 39.2mm
-- The product can be used: signal source, valve adjustment, inverter control, PLC debugging, instrumentation test, analog transmitter output.

Redefine the display function:
If the menu requires a password, the default password is 1234, flashing display.
Such as, if it is used to control a device for -90 degrees to +90 degrees action.
The default display is Current.
It can also be redefined as: 4mA display -90.00, 20mA display +90.00 (2 decimal point), this can be displayed as 4-20mA -90.00 to 90.00 (2 decimal point).

Package included:
1x 4-20mA Signal Source Signal Generator

Features

  • HANDY KNOB OPERATION: DROK signal generator kit has multi-ring (5 * 360) potentiometer knob operation, stepless fine adjustment, in response to the output immediately, no delay.
  • PRECISE REGULATION DESIGN: This generator is provided with potentiometer to adjust the actual fineness which is up to 0.01mA.
  • WIDE POWER SUPPLY RANGE: Our signal source is available for wide power supply range (DC12-30V), DC 12V or 24V, current 18mA. The power port has a polarity protection, which power reverse does not work, do not burn components.
  • EFFORTLESS INSTALLATION: Easy to install, standard 7943 shell, panel size: 79mm * 43mm * 25mm,hole size: 76.5mm * 39.2mm.
  • VERSATILE GENERATOR KIT: The product can be used: signal source, valve adjustment, inverter control, PLC debugging, instrumentation test, analog transmitter output.
  • See more on Amazon...

Brand: DROK   |   Manufacturer: DROK

Package Dimensions: 3 x 4 x 5 inches (7.6 x 10.2 x 12.7 cm)

Amazon Price: $20.99 | as of 01/17/2019(2:44pm pst)
Availibility: Usually ships in 24 hours
List Price: $20.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #11

UCTRONICS DC 0-10V 0/4-20mA Current Voltage Signal Generator, USB Power Supply Interface Analog Simulator for PLC and Panel Debugging, Device Testing, Frequency Converter, Flow Valve

 PartNumber: U6206   |   Asin: B07L491RLM

UCTRONICS signal generator is designed to simulate 0-10V voltage signal and 0/4-20mA current signal for PLC and panel Debugging, Device Testing, Frequency Converter, Flow Valve, ect. Very easy to use, it can be connected with micro USB-5V power supply or DC 15-30V external power. What's more, it can display 4 different types of digit, 0-10V voltage, 0-22mA current, 0-100 percent and 0-50HZ. It will play a important role in your electronics work.

Features

  • Power Supply: external micro USB-5V or external power DC 15-30V, each way makes the generator work, both ways also can be connected at the same time.
  • Voltage Output: 0-10V, precision is 0.01V, rotate the encoder knob to adjust output voltage, can be calibrated.
  • Current Output: 0-22mA, precision is 0.01mA, rotate the encoder knob to adjust output current, can be calibrated.
  • Multiple Display: just push the small botton to switch the display mode between voltage and current, you can also follow the instructions to switch 0-100 percent or 0-50HZ display.
  • Product Dimension: 3.94 x 2.36 x 0.98 (100mm x 60mm x 25mm), portable and convenient.
  • See more on Amazon...

Brand: UCTRONICS   |   Manufacturer: UCTRONICS

Package Dimensions: 1.5 x 3.6 x 4.6 inches (3.8 x 9.1 x 11.7 cm)

Amazon Price: $29.99 | as of 01/17/2019(2:44pm pst)
Availibility: Usually ships in 24 hours
List Price: $29.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #12

Onyehn XR2206 High Precision Function Signal Generator DIY Kit Sine/Triangle/Square Output 1Hz-1MHz Adjustable Frequency Amplitude + Transparent Case Box Shell

 Ean: 7593064134482   |    PartNumber: 209   |   Asin: B078X9PVX3

Specifications:
Voltage Supply: 9-12V DC Input
Waveforms: Square, Sine & Triangle
Impedance: 600 Ohm + 10%
Frequency: 1Hz-1MHz

SINE WAVE
Amplitude: 0-3V at 9V DC Input
Distortion: Less than 1% (at 1KHz)
Flatness: +0.05dB 1Hz - 100kHz

SQUARE WAVE
Amplitude: 8V (no load) at 9V DC Input
Rise Time: Less than 50ns (at 1KHz)
Fall Time: Less than 30ns (at 1KHz)
Symmetry: Less than 5% (at 1KHz)

TRIANGLE WAVE
Amplitude: 0-3V at 9V DC Input
Linearity: Less than 1% (up to 100KHz) 10mA

Package Size: Approx. 12 * 8 * 2cm / 4.72 * 3.15 * 0.8in
Package Weight: 69g / 2.46oz

The welding installation considerations, follow these steps:
1. The components are welding the front board, from low to high principles, namely the first low welding components, such as, capacitor, resistor, diode, etc.
2.Welding IC socket, terminal blocks, finally power socket, adjustable potentiometer.
3.The back with a diagonal cutting pliers to cut short the pins as far as possible.

Debugging steps:
1After completion of welding on IC, XR2206, pay attention to the direction of IC, insert the might damage the chip!
2. check the IC whether against, such as anti please timely correction.
3. Insert the power supply, power supply for 5.5 * 2.1 port, inside outside is negative polarity. For 9-12 v power supply voltage. The waveform may not be stable for more than 12V.

Using the step
1. J1 jumper cap plug in, SIN/TRI blue terminals output sine wave (note J1, J2 can only insert one of)
2. J2 jumper cap plug in, SIN/TRI blue terminals output triangular wave (note J1, J2 can only insert one of)
3. SQU blue terminals output pulse
4. AMP : Sine wave, triangle wave amplitude adjustment
5. FINE : Frequency fine adjustment
6. Coarse : Frequency of coarse adjustment

Features

  • High Precision, can generate sine/triangle/square waveforms.
  • Output frequency range: 1Hz-1MHz and Adjustable frequency and amplitude.
  • Wide power supply range, use 9-12V external power or 9V battery(NOT Included).
  • This is a DIY kit with All are through hole components,easily assemble the Function Generator by yourself.
  • BaiJJ XR2206 High Precision Function Signal Generator DIY Kit Sine/Triangle/Square Output 1Hz-1MHz Adjustable Frequency Amplitude + Transparent Case Box Shell
  • See more on Amazon...

Brand: Onyehn   |   Manufacturer: Onyehn

Package Dimensions: 0.59 x 5.31 x 7.64 inches (1.5 x 13.5 x 19.4 cm)

Amazon Price: $11.99 | as of 01/17/2019(2:44pm pst)
Availibility: Usually ships in 24 hours
List Price:

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #13

Longruner 24MHz Dual-Channel DDS Function Signal Generator, High Precision Arbitray Waveform Generator FY3224S (White)

Model: FY3324S   |    Mpn: FY3324S   |    PartNumber: FY3324S   |   Asin: B06VTQQ5QX

Kindly remind: Before using this instrument, please check if the power supply is normal, to ensure the normal use and personal safety. This instrument must be used in the technical index range. Please do not change the instrument circuit arbitrarily, so as to avoid damaging equipment or endangering the safety. Function Features: Sampling rate up to 250 MSa/s. Built-in arbitrary waveform with 250 MSa/s sampling rate. 4 downloadable 2048 dots arbitrary waveform memories. With 12 bit wide waveform generator, the output waveform can be more delicate with low distortion. Each function can be adjusted by host computer. Preinstalled 17 common waveforms. High resolution: Full range frequency resolution can be 10 mHz. Both main and subsidiary wave duty cycle are adjustable separately (0.1%~99.9%). All range continuously adjustable, digital directly setting. High waveform accuracy: The output waveform synthesized by function calculation is of high accuracy and low distortion. Arbitrary waveform: User can load arbitrary waveform according to the need. Sweep Function: Linear sweep and Logarithmic sweep. Starting and stop points can be set optionally. Package Contents: 1x 24MHz Dual Channel DDS Function Signal Generator 1x 1m power cable 1x 1.25mUSB cable 2x 1.1m Q9 cables

Features

  • Longruner Arbitray Waveform Generator adopts large scale CMOS integrated circuit and high speed microprocessor. The internal circuit adopts active crystal oscillator as benchmark. So the signal stability is greatly strengthened.
  • Using Dual-channel DDS direct digital synthesis technology to generate precise, stable, low distortion output signal. includes Sine wave, Square wave, Triangle wave, Saw tooth wave and user-defined waveform, each channel can be independently set the parameters.
  • It has TTL electric level output, External frequency measurement, counter and sweep functions including Linear sweep and Logarithmic sweep. Both the sweep frequency and time can be set arbitrarily.
  • Storage feature: You can store 20 groups instrument state parameters set by the user, can be called up to Reproduce.
  • This Signal Generator is the ideal instrument for electronic engineering, laboratories, production lines, teaching and scientific research. The DC bias level is adjustable, it can adjust from -10V to + 10V , other similar product do not have this function.
  • See more on Amazon...

Brand: Longruner   |   Manufacturer: Longruner

Package Dimensions: 3.9 x 8.4 x 9.9 inches (9.9 x 21.3 x 25.1 cm)

Amazon Price: $58.09 | as of 01/17/2019(2:44pm pst)
Availibility: Usually ships in 24 hours
List Price: $135.00

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #14

Siglent Technologies SDG1032X Arbitrary Waveform - Function Generator

Model: SDG1032X   |    Mpn: SDG1032X   |    Ean: 0713839551390   |    PartNumber: SDG1032X   |   Asin: B01LECZU98

The SIGLENT SDG1032X is siglent's latest addition to an already powerful line of arb/function generators. With the ability to offset the phase between CH1 and CH2, numerous modulation types, a harmonics generation mode, this 30 MHz generator can generate square waves to 30 MHz. A feature not found in most other generators in this price Class.

Features

  • 1 uhz - 30 MHz
  • Square waves to 30 mhz
  • Dual channel. Sweep/ burst/ modulation/ harmonics
  • Ch1 - Ch2 waveform combining. Built-in frequency counter
  • Usb/ lan interfaces. Includes easy wave arbitrary waveform editing software
  • See more on Amazon...

Brand: Siglent Technologies   |   Manufacturer: Siglent Technologies

Package Dimensions: 8.5 x 13.5 x 14.5 inches (21.6 x 34.3 x 36.8 cm)

Amazon Price: $359.00 | as of 01/17/2019(2:44pm pst)
Availibility: Usually ships in 24 hours
List Price: $359.00 | Used Price: $315.78

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #15

Koolertron 60MHz High Precision DDS Signal Generator Counter,Upgraded Dual-Channel Arbitrary Waveform Function Generator Frequency Meter 266MSa/s (60MHz)

Model: CJMDS26-F   |    Mpn: GH-CJDS2   |    Ean: 0886085653788   |    PartNumber: GH-CJDS2   |   Asin: B07596133Q

Advantage:
High frequency precision up to 10-6 orders of magnitude.
Full range of 0.01 Hz frequency resolution.
Minimum amplitude resolution can be up to 1mV.
Amplitude range is 0Vpp~20Vpp.
Duty cycle of each channel can be adjusted separately. Precision can be 0.1%.

Frequency Characteristic:
Sine wave: 0~60MHz
Square & Triangle Wave: 0~15MHz
Pulse & Arbitrary & TTL Digital Signal Wave: 0~6MHz
Square rise time: 15nS
Pulse width adjustment range: 30nS-4000S
With pulse trains burst output function, allow the unit output 1~1048575 arbitrary pulse trains.
Frequency accuracy: 20ppm
Frequency stability: 1ppm/3h

Waveform Characteristic:
Waveform: Sine, Square, Triangle, Pulse (duty-cycle correction,Pulse width and cycle time adjustable), Partial Sine, CMOS, DC level, Half-wave, Full-Wave, Pos-Ladder, Neg-Ladder, Noise, Exponential Rise, Exponential Fall, Tone, Sine Pulse, Lorentz Pulse, and 60 kinds user defined waveform

Phase characteristic:
Phase adjusting range: 0~359.9
Phase resolution: 0.1

TTL/COMS Output:
Low level:

Features

  • Arbitrary Waveform Generator adopts large scale FPGA integrated circuit and high speed MCU microprocessor. The internal circuit adopts active crystal oscillator as benchmark. So the signal stability is greatly strengthened.
  • Using Dual-channel DDS signal and TTL electric level output to generate precise, stable, low distortion output signal. includes Sine, Square, Triangle, Pulse, Partial Sine, CMOS, DC level, Half-wave, Full-Wave, Pos-Ladder, Neg-Ladder, Noise, Exponential Rise, Exponential Fall, Tone, Sine Pulse, Lorentz Pulse, and 60 kinds user defined waveform etc. each channel can be independently set the parameters.
  • With linear sweep(Max. up to 999.9s) and logarithmic frequency sweep functions.Has a frequency measurement, period measurement, positive and negative pulse width measurement and counting function.
  • Storage feature: You can store 100 groups instrument state parameters set by the user, can be called up to Reproduce. Frequency output of Sine wave can be up to 60MHz. 266MSa/s sampling rate. It has 60 positions for saving user-defined waveform. Waveform Length of each one is 2048 and vertical resolution is 14 bits
  • This Signal Generator is the ideal instrument for electronic engineering, laboratories, production lines, teaching and scientific research.
  • See more on Amazon...

Brand: Koolertron   |   Manufacturer: Koolertron

Package Dimensions: 3.7 x 5 x 9.5 inches (9.4 x 12.7 x 24.1 cm)

Amazon Price: $118.99 | as of 01/17/2019(2:44pm pst)
Availibility: Usually ships in 24 hours
List Price: $118.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #16

Siglent Technologies SDG2042X Arbitrary Waveform Function-Generators, 40 MHz, Grey

Model: SDG2042X   |    Mpn: SDG2042X   |    Ean: 0718520016349   |    PartNumber: SDG2042X   |   Asin: B01410O55U

Siglent's new SDG2000X series of function generators offer a 1.2 GSa/s interpolated sample rate with 16 bits of vertical resolution. The proprietary TrueArb & EasyPulse techniques help to solve weaknesses inherent in traditional DDS generators when generating arbitrary, square, and pulse waveforms. Siglent's EasyWave arbitrary waveform software is included.

Features

  • Dual channel * 40 MHz (Sine wave) * Touch screen display
  • 16 bit vertical resolution * Modulation / Sweep / Burst
  • TrueArb Technology / Easy Pulse Technology
  • Built-in high precision Frequency Counter
  • USB / LAN interfaces. Optional GPIB adapter available
  • See more on Amazon...

Brand: Siglent Technologies   |   Manufacturer: Siglent Technologies

Package Dimensions: 7.8 x 14.41 x 15.35 inches (19.8 x 36.6 x 39.0 cm)

Amazon Price: $498.00 | as of 01/17/2019(2:44pm pst)
Availibility: Usually ships in 24 hours
List Price: $499.00 | Used Price: $483.43

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #17

SainSmart UDB1002S DDS Signal Generator, 2MHz Sweep Function Source Rev3.0 PC Serial Ports COMM

 Ean: 6955170846788   |    PartNumber: UDB1002S   |   Asin: B00JTR66CG

This is a complete DDS signal source, Adopts DC5V power supply, can output the sine wave, square wave (Duty cycle Can be adjust from1% -99%) , triangle wave and sawtooth wave and various function wavefrom, maximum output can reach up to 10 Vpp, frequency range from 0.01 Hz-2 MHz .Resolution for 10 MHz, with TTL synchronization output and 60 MHz frequency meter.

Specifications:

* MAX Frequency:2MHz
* Wave form:sine wave, square wave,triangle wave and sawtooth wave
* Max output:10Vpp(no-load)
* Otput Resistance: 50 10%
* DC bias: 5V
* Duty cycle:1%-99%
* Display: LCD1602
* Output frequency range:
* sine wave: 0.01Hz-2MHz
* Square-wave: 0.01 Hz - 1MHz (the valid range)
* Triangle wave :0.01 Hz - 1MHz (the valid range)
* Sawtooth wave :0.01 Hz ~ 1MHz (the valid range)
* Resolution :0.01 Hz
* Frequency stability: + 1 x 10-6
* Frequency error :+ 5 x 10-6
* Sine wave distortion degree: Manual: https://s3-ap-northeast-1.amazonaws.com/sain-amzn/20/20-010-501/20-010-501.zip

Features

  • UDB100X series direct digital synthesis signal generator use DDS technology and FPGA design with the characters of high stability and low distortion ect., It's the ideal equipment of electronic engineer, laboratory, production lines, the teaching and scientific research.
  • The UDB100xS series adds a PC communication control functions.
  • The serial communication from the July 19, 2011 UDB100xS Series DDS source
  • Can connect a PC to communicate and use computer software to control instruments
  • Should be noted that the amplitude and DC offset can not be programmed, and other functions (frequency, duty cycle, waveform set and the sweep time and the corresponding control, read outside the measurement frequency, etc.) are able to achieve the programmed function
  • See more on Amazon...

Brand: SainSmart   |   Manufacturer: SainSmart

Package Dimensions: 3.31 x 4.65 x 5.28 inches (8.4 x 11.8 x 13.4 cm)

Amazon Price: $31.99 | as of 01/17/2019(2:44pm pst)
Availibility: Usually ships in 24 hours
List Price: $33.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #18

Signal Generator, DROK DC 3.3-30V Function Generator 5-30mA 5V 12V 24V LCD Display Adjustable PWM Pulse Frequency Duty Cycle Duty Ratio Rectangular Wave Square Wave Signal Generator Module XY-PWM

 PartNumber: 200382AFA   |   Asin: B07KVYQ78K

Parameter: 1. Working voltage: DC 3.3v~30v 2. Frequency range: 1Hz~150kHz (divided into 4 ranges); 3. Frequency precision: 2% of each range; 4. Signal load capacity: output current is about 5-30mA; 5. Output Amplitude: PWM amplitude equal to the input voltage value 6. Environment Temperature Range: -20~+70 7. Duty cycle range: 0-100%. Application: 1. As square wave signal generator for experimental development; 2. As square wave signal generator for motor driver; 3. As adjustable pulse generator for MCU; 4. As pulse generator, control related circuits (PWM dimming, speed regulating). Setting Parameters: There are 4 independent buttons on the module for setting the frequency value and the duty cycle value. Supports short press (increase or decrease one unit by one unit) and long press (fast increase or decrease). All setting parameters will be saved when powered off to achieve data guaranteed. Frequency Display Instruction: The frequency is divided into 4 ranges and switched automatically. 1. XXX (without decimal point): minimum unit is 1Hz, value range is 1Hz~999Hz. 2. X.XX (the decimal point is in the hundred digit): minimum unit is 0.01kHz, value range is 1.00kHz~9.99kHz. 3. XX.X (the decimal point is in the ten digit): minimum unit is 0.1kHz; value range is 10.0kHz~99.9kHz. 4. X.X.X (full decimal point): the minimum unit is 1kHz; the value range is 1kHz~150kHz e.g. Frequency displays 100 represents 100Hz; displays 1.01 represents 1.01kHz; displays 54.1 represents 54.1kHz; displays 1.2.4 represents 124kHz Package Included: 1x Signal Generator

Features

  • PARAMETER ---- operating voltage range DC 3.3v~30v; frequency range 1Hz-150kHz; output current 5-30mA; duty cycle range 0-100%.
  • APPLICATION ---- as square wave signal generator for experimental development; as square wave signal generator for motor driver; as adjustable pulse generator for MCU; as pulse generator, control related circuits (PWM dimming, speed regulating).
  • SERIAL COMMUNICATION ---- support serial communication, TTL level.
  • DATA AUTO STORAGE ---- all parameters will be saved automatically after setting and therefore won't lose when power off.
  • OTHER FEATURES ---- with LCD display to display frequency and duty cycle value; with case; PWM output, can set frequency and duty cycle separately by buttons; frequency value is divided into 4 range and switched automatically, with high precision.
  • See more on Amazon...

Brand: DROK   |   Manufacturer: DROK

Package Dimensions: 1.9 x 2.8 x 4.4 inches (4.8 x 7.1 x 11.2 cm)

Amazon Price: $12.59 | as of 01/17/2019(2:44pm pst)
Availibility: Usually ships in 24 hours
List Price: $12.59

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #19

Walmeck XR2206 High Precision Function Signal Generator DIY Kit Sine/Triangle/Square Output 1Hz-1MHz Adjustable Frequency Amplitude

 PartNumber: PKJ2692623918435PG   |   Asin: B079QLG5GR

This signal generator DIY kit is professional product to generate sine/triangle/square wave. It's a DIY kit for you to weld and install. Features: High resolution, can generate sine/triangle/square waveforms. Frequency range: 1Hz-1MHz. Adjustable frequency and amplitude. Frequency adjustment features coarse tuning and fine tuning. Wide power supply range, use 9-12V external power or 9V battery(NOT Included). All are through hole components, easy for installation. Specifications: Voltage Supply: 9-12V DC Input Waveforms: Square, Sine & Triangle Impedance: 600 Ohm + 10% Frequency: 1Hz-1MHz SINE WAVE Amplitude: 0-3V at 9V DC Input Distortion: Less than 1% (at 1KHz) Flatness: +0.05dB 1Hz - 100kHz SQUARE WAVE Amplitude: 8V (no load) at 9V DC Input Rise Time: Less than 50ns (at 1KHz) Fall Time: Less than 30ns (at 1KHz) Symmetry: Less than 5% (at 1KHz) TRIANGLE WAVE Amplitude: 0-3V at 9V DC Input Linearity: Less than 1% (up to 100KHz) 10mA Package Size: Approx. 12 * 8 * 2cm / 4.72 * 3.15 * 0.8in Package Weight: 69g / 2.46oz Package List: 1 * Signal Generator DIY Kit 1 * User Manual(English)

Features

  • High resolution, can generate sine/triangle/square waveforms.
  • Frequency range: 1Hz-1MHz.
  • Adjustable frequency and amplitude.
  • Frequency adjustment features coarse tuning and fine tuning.
  • Wide power supply range, use 9-12V external power or 9V battery(NOT Included).
  • See more on Amazon...

Brand: Walmeck   |   Manufacturer: Walmeck

Package Dimensions: 0.79 x 3.15 x 4.72 inches (2.0 x 8.0 x 12.0 cm)

Amazon Price: $6.99 | as of 01/17/2019(2:44pm pst)
Availibility: Usually ships in 1-2 business days
List Price: $6.99

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon



  #20

Anmbest XR2206 1Hz-1MHz Adjustable Frequency Amplitude Sine/Triangle/Square Output High Stability and Accuracy Monolithic Function Signal Generator DIY Kit with Case

 Ean: 7898822206686   |    PartNumber: Anmbest_MD16   |   Asin: B07CRKTX5X

Technical Specifications:
Voltage Supply: 9-12V DC Input
Waveforms: Square, Sine & Triangle
Impedance: 600 Ohm + 10%
Frequency: 1Hz-1MHz
Power consumption : 750mW
SINE WAVE
Amplitude: 0-3V at 9V DC Input
Distortion: Less than 1% (at 1KHz)
Flatness: +0.05dB 1Hz - 100kHz
SQUARE WAVE
Amplitude: 8V (no load) at 9V DC Input
Rise Time: Less than 50ns (at 1KHz)
Fall Time: Less than 30ns (at 1KHz)
Symmetry: Less than 5% (at 1KHz)
TRIANGLE WAVE
Amplitude: 0-3V at 9V DC Input
Linearity: Less than 1% (up to 100KHz) 10mA

Package includes:
1 x XR2206 Module DIY Kit with Case

Features

  • Function Generator is an essential laboratory equipment for every electronic. It allows a variety of measurements and experiments
  • XR2206 Function Generator is capable of producing high quality sine, square and triangle waveforms of high-stability and accuracy, Sawtooth wave and pulse wave can be generated by adjusting the duty cycle
  • Frequency adjustment features coarse tuning and fine tuning, adjustment range from 1HZ to 1MHZ
  • Wide power supply range, use 9-12V external power or 9V battery
  • The XR2206 consists of several parts, You need to assemble yourself
  • See more on Amazon...

Brand: Anmbest   |   Manufacturer: Anmbest

Package Dimensions: 0.55 x 3.74 x 5.55 inches (1.4 x 9.5 x 14.1 cm)

Amazon Price: $11.59 | as of 01/17/2019(2:44pm pst)
Availibility: Usually ships in 24 hours
List Price: $25.19

See Amazon Reviews | Add to your Amazon Wishlist

See On Amazon




Looking For Something Else? Search

Most Popular
New Releases

  1. 4-20mA Generator, DROK Adjustable Signal Generator, DC 0-10V 0/4-20mA Current Voltage Analog Simulat...
  2. Signal Generator DIY Kit, KKmoon XR2206 High Precision Function Signal Generator DIY Kit Sine/Triang...
  3. Koolertron Upgraded 15MHz DDS Signal Generator Counter,High Precision Dual-channel Arbitrary Wavefor...
  4. XR2206 Function Generator - kuman Updated XR2206 DIY Kit Signal Generator with Screwdriver and Jumpe...
  5. Koolertron Upgraded 60MHz DDS Signal Generator Counter,High Precision Dual-channel Arbitrary Wavefor...
  6. Siglent SDG1025 Function/Arbitrary Waveform Generator, 25MHz, 125MSa/s Sample Rate
  7. Signal Generator, KKmoon High Precision Digital DDS Dual-Channel Signal Source Generator Arbitrary W...
  8. Yosoo 1HZ-500KHz DDS Function Signal Generator Module Sine+Triangle+Square Wave
  9. Signal Detector, KKmoon High Precision Digital DDS Dual-channel Signal Source Generator Arbitrary Wa...
  10. 4-20mA Signal Generator, DROK 4 Digits Constant Current Source Generator with Adjustable Digital Pot...

Most Wished For

  1. 4-20mA Generator, DROK Adjustable Signal Generator, DC 0-10V 0/4-20mA Current Voltage Analog Simulat...
  2. Signal Generator DIY Kit, KKmoon XR2206 High Precision Function Signal Generator DIY Kit Sine/Triang...
  3. Koolertron Upgraded 15MHz DDS Signal Generator Counter,High Precision Dual-channel Arbitrary Wavefor...
  4. XR2206 Function Generator - kuman Updated XR2206 DIY Kit Signal Generator with Screwdriver and Jumpe...
  5. Koolertron Upgraded 60MHz DDS Signal Generator Counter,High Precision Dual-channel Arbitrary Wavefor...
  6. Siglent SDG1025 Function/Arbitrary Waveform Generator, 25MHz, 125MSa/s Sample Rate
  7. Signal Generator, KKmoon High Precision Digital DDS Dual-Channel Signal Source Generator Arbitrary W...
  8. Yosoo 1HZ-500KHz DDS Function Signal Generator Module Sine+Triangle+Square Wave
  9. Signal Detector, KKmoon High Precision Digital DDS Dual-channel Signal Source Generator Arbitrary Wa...
  10. 4-20mA Signal Generator, DROK 4 Digits Constant Current Source Generator with Adjustable Digital Pot...

Most Gifted

  1. 4-20mA Generator, DROK Adjustable Signal Generator, DC 0-10V 0/4-20mA Current Voltage Analog Simulat...
  2. Signal Generator DIY Kit, KKmoon XR2206 High Precision Function Signal Generator DIY Kit Sine/Triang...
  3. Koolertron Upgraded 15MHz DDS Signal Generator Counter,High Precision Dual-channel Arbitrary Wavefor...
  4. XR2206 Function Generator - kuman Updated XR2206 DIY Kit Signal Generator with Screwdriver and Jumpe...
  5. Koolertron Upgraded 60MHz DDS Signal Generator Counter,High Precision Dual-channel Arbitrary Wavefor...
  6. Siglent SDG1025 Function/Arbitrary Waveform Generator, 25MHz, 125MSa/s Sample Rate
  7. Signal Generator, KKmoon High Precision Digital DDS Dual-Channel Signal Source Generator Arbitrary W...
  8. Yosoo 1HZ-500KHz DDS Function Signal Generator Module Sine+Triangle+Square Wave
  9. Signal Detector, KKmoon High Precision Digital DDS Dual-channel Signal Source Generator Arbitrary Wa...
  10. 4-20mA Signal Generator, DROK 4 Digits Constant Current Source Generator with Adjustable Digital Pot...

Top Selling

  1. 4-20mA Generator, DROK Adjustable Signal Generator, DC 0-10V 0/4-20mA Current Voltage Analog Simulat...
  2. Signal Generator DIY Kit, KKmoon XR2206 High Precision Function Signal Generator DIY Kit Sine/Triang...
  3. Koolertron Upgraded 15MHz DDS Signal Generator Counter,High Precision Dual-channel Arbitrary Wavefor...
  4. XR2206 Function Generator - kuman Updated XR2206 DIY Kit Signal Generator with Screwdriver and Jumpe...
  5. Koolertron Upgraded 60MHz DDS Signal Generator Counter,High Precision Dual-channel Arbitrary Wavefor...
  6. Siglent SDG1025 Function/Arbitrary Waveform Generator, 25MHz, 125MSa/s Sample Rate
  7. Signal Generator, KKmoon High Precision Digital DDS Dual-Channel Signal Source Generator Arbitrary W...
  8. Yosoo 1HZ-500KHz DDS Function Signal Generator Module Sine+Triangle+Square Wave
  9. Signal Detector, KKmoon High Precision Digital DDS Dual-channel Signal Source Generator Arbitrary Wa...
  10. 4-20mA Signal Generator, DROK 4 Digits Constant Current Source Generator with Adjustable Digital Pot...



Main Categories

Home & Garden


Home Improvement


Electronics


Office


Car & Automotive


Sporting Goods


Toys and Hobby


Health & Personal Care


Beauty Supplies


Fashion


Industrial


Related Categories

Abrasive & Finishing


Cutting Tools


Fasteners


Filtration


Commercial Door Products


Hydraulics, Pneumatics & Plumbing


Industrial Hardware


Industrial Tools


Food Services


Janitorial & Sanitation


Lab Equipment


Material Handling


Occupational Health


Packaging & Shipping


Power Transmission


Dental Supplies


Medical Supplies


Raw Materials


Retail Fixtures & Equipment


Tapes, Adhesives & Sealants


Test, Measure & Inspect


Robotics, 3D Printing & Science Education


Industrial Electrical