BIGTREETECH Octopus V1.1 Control Board 32bit Compatible TFT Series Screen, Support DIY Klipper Firmware and Raspberry-Pi Online Printing for Voron V2.4 Upgrade 3D Printer (with 8Pcs TMC2209)
Asin: B09713SRVP | Model: KINGPRINTER-UUU001949 | PartNumber: KINGPRINTER-UUU001949
As an Amazon Associate we earn a fee from qualifying purchases when you follow a link to Amazon from this page. We rank the products, but the links to Amazon are promotional.đăMotherboard Expansion FunctionăSupport Bltouch, Locked-Rotor Detection, Shutdown After Printing, Resume Printing After Power Failure, Can Bus, U Disk Function, Iic Expansion; At The Same Time Reserved Wifi Interface, Pt100 Thermistor Interface (Optional), Dual Z-Axis Printer..
đăTmc2209 Driver ModeăTmc Motor Drivers Can Be Used In Spi Or Uart Mode By Simply Adjusting The Onboard Jumpers Beneath Each Motor Driver. Additionally You Can Connect Or Disconnect The Tmc Diag Pin Using An Onboard Jumper Allowing You To Use Hard Endstops Or Sensorless Homing Without The Need To Cut Any Pins..
đăTmc2209 Driver FeaturesăThe Tmc2209 Stepper Driver Is Not Easy To Lose Steps And Is In An Ultra-Quiet Mode; The Module Has A Large Area Of Heat Dissipation Pad, Which Can Reduce The Temperature Of The Driver When It Is Working; The Module Supports Three Modes: Step / Dir And Uart..
đăStrong Diy SupportăThis Motherboard Supports Up To 8 Stepper Drivers With 9 Stepper Driver Outputs In Total; And Up To 6 Pwm Fans And 2 Always-On Fans With The Ability To Individually Select The Voltage Rail That Will Drive Each Fan. Select From Vin, 12V Or 5V..
Features
- Main Control Chip Uses a 32-bit ARM Cortex-M4 series STM32F446ZET6 main control chip with a core frequency of 180MHz.
- Strong DIY Support This motherboard supports up to 8 stepper drivers with 9 stepper driver outputs in total; And up to 6 PWM fans and 2 always-on fans with the ability to individually select the voltage rail that will drive each fan. Select from Vin, 12V or 5V.
- Motherboard Expansion Function Support BLTouch, locked-rotor detection, shutdown after printing, resume printing after power failure, CAN bus, U disk function, IIC expansion; at the same time reserved WIFI interface, PT100 thermistor interface (optional), dual Z-axis printer.
- TMC2209 Driver Features The TMC2209 stepper driver is not easy to lose steps and is in an ultra-quiet mode; the module has a large area of heat dissipation pad, which can reduce the temperature of the driver when it is working; the module supports three modes: STEP / DIR and UART.
- TMC2209 Driver Mode TMC Motor drivers can be used in SPI or UART mode by simply adjusting the onboard jumpers beneath each motor driver. Additionally you can connect or disconnect the TMC DIAG pin using an onboard jumper allowing you to use hard endstops or sensorless homing without the need to cut any pins.
- See more on Amazon...
Brand: BIGTREETECH | Manufacturer: BIGTREETECH
See On Amazon Similar To BIGTREETECH Octopus V1.1 Control Board
#1
BIGTREETECH HDMI5 V1.1 Touchscreen Monitor 5 inch IPS LCD Display 800 480 for Raspberry-Pi 4B/3B, BTT PI V1.2/PI 2 Compatible with SKR Mini E3 V3.0/Octopus/Manta M4P/M5P SKR 3 to Running Klipper
Asin: B0CMZYBPDF | Model: USA6-1040000039 | PartNumber: USA6-1040000039
Btt 5 Inch Hdmi Display Built-In Audio Decoding Circuit, Support 3.5Mm Headphone Jack Audio Output And Brightness And Display Direction Adjustment..
ă After-Sales ServiceăThe Manual And Installation Instructions Have Been Uploaded To Github, If You Have Any Problems During Use, Please Contact Us At The First Time, We Will Give You A Satisfactory Solution..
Widely Compatible B: Bigtreetech Hdmi5 V1.1 Display Working With Cb1/Cb2, Compatible With Manta M4p/M5p/M8p, Matan Ez E3 Board, It Can Running Klipper Touch Screen Mode..
4Pin Xh2.54 Breakout Port. The 4-Pins Xh2.54 Breakout Port Allows Custom Connection Via Usb Protocol, As Well As Screen Independent Power (Dc 5V), Giving Users More Diy Options..
Widely Compatible A: Btt Hdmi5 V1.1 Ips Lcd Display Compatible With Btt Pi V1.2/Pi 2 Or Cb1/Cb2+Pi4b, Can Working With Skr Mini E3 V3.0/Skr Pico/Skr V1.4 Turbo/Skr 3/Octopus Series/Kraken/Skr Pro V1.2 3D Printer Board, Running Klipper Touch Screen Mode. For Voron, Corexy, Vzbot, I3 3D Printers..
Bigtreetech 5 Inch Hdmi Touch Screen Adopts 5 Inch Ips Capacitive Touch Screen With A Resolution Of 800X480, 160Viewing Angle, Support Up To 5-Point Touch..
Features
- BIGTREETECH HDMI5 touchscreen desinged for users of 3d printers using the Klipper system. HDMI input, suitablec for Raspberry Pi4, PI4B+CB1/CB2, BTT PI V1.2/BTT PI 2, Banana Pi, Windows 10 8 7, and other mini PC.
- BIGTREETECH 5 inch hdmi touch screen adopts 5 inch IPS capacitive touch screen with a resolution of 800x480, 160viewing angle, support up to 5-point touch.
- BTT 5 inch hdmi display built-in audio decoding circuit, support 3.5mm headphone jack audio output and brightness and display direction adjustment.
- Widely Compatible A: BTT HDMI5 V1.1 IPS LCD display compatible with BTT PI V1.2/PI 2 or CB1/CB2+PI4B, can working with SKR Mini E3 V3.0/SKR Pico/SKR V1.4 Turbo/SKR 3/Octopus series/Kraken/SKR Pro V1.2 3D printer board, running Klipper touch screen mode. for Voron, CoreXY, VZbot, I3 3D Printers.
- Widely Compatible B: BIGTREETECH HDMI5 V1.1 display working with CB1/CB2, compatible with Manta M4P/M5P/M8P, Matan EZ E3 board, it can running Klipper touch screen mode.
- 4pin XH2.54 breakout port. The 4-pins XH2.54 breakout port allows custom connection via USB protocol, as well as screen independent power (DC 5V), giving users more DIY options.
- After-sales Service The manual and installation instructions have been uploaded to Github, If you have any problems during use, please contact us at the first time, we will give you a satisfactory solution.
- See more on Amazon...
Brand: BIGTREETECH | Manufacturer: BIGTREETECH
Dimensions: 0.39 x 4.76 x 2.99 Inches
See On Amazon #2
BIGTREETECH Pi V1.2 Control board 64bit Quad Core 1GB DDR3L 40-pin GPIO Compatible with SKR MINI E3 V3.0 Octopus/SKR V1.4 turbo to run Klipper/Linux/Debain For I3/CoreXY 3D Printer
Asin: B0C46B6X64 | Model: PI V1.2 | PartNumber: PI V1.2
ăSupport Display And MotherboardăBtt Pi V1.2 Core Board Display Adopts Malig32 Mp2 Gpu, Support Opengl3.2 And Hdmi2.0A Uhd 4K Video & Audio Output And Spi ScreenïŒBtt Hdmi5/7, Tft35 Spi), Onboard 4Xusb2.0 Port. Powerful High Performance Details And Clarity. Motherboard Support Skr Mini E3 V3.0, Skr Pico, Skr V1.4 Turbo, Skr 3, Kraken, Octopus Pro/Octopus V1.1 Series. Then Running Klipper Firmware..
ăFlexible PowerăSupport Usb-C 5V Power Supply And Dc12v-24V From A 3D Printer, Making It Easy And Efficient To Power Up The Board Without Any Extra Adapters Or Power Soucres..
ăRich ConnectivityăOnboard Standard 40-Pingpio Header, 3.5Mm Audio Jack, Tf Card Slot, Adxl345 Spi, Usb To Can Module(Requires Can Adapter V1.0 Module). Built-In Ir Receiver. Rj45 Port Support A 100Mbps Wired Network, Built-In 2.4G Wifi Module, Supports 100Mbps Wireless Network, Users Can Connect The Inlculde Wifi Antenna To Get A Stronger And More Stable Wifi Signa..
ăAbout SizeăBtt Pi V1.2 Control Board Size Is 85*56Mm, The Same As The Raspberry-Pi 3B/4B, Making It A Seamless Fit For Your Existing Projects..
Features
- Main Control Chip BIGTREETECH BTT Pi v1.2 board adopts ALLWINNER H616, 64-bit Quad-core, Cortex-A53@1.5GHz Processor, RAM is 1GB DDR3L SDRAM.
- About Size BTT Pi v1.2 control board size is 85*56mm, the same as the Raspberry-Pi 3B/4B, Making it a seamless fit for your existing projects.
- Support Display and Motherboard BTT Pi v1.2 core board display adopts MaliG32 MP2 GPU, support OpenGL3.2 and HDMI2.0A UHD 4K Video & Audio output and SPI screen BTT HDMI5/7, TFT35 SPI), onboard 4xUSB2.0 port. Powerful high performance details and clarity. Motherboard support skr mini e3 v3.0, skr pico, skr v1.4 turbo, skr 3, Kraken, Octopus pro/Octopus V1.1 series. then running Klipper firmware.
- Rich Connectivity Onboard standard 40-pinGPIO header, 3.5mm audio jack, TF card slot, adxl345 spi, USB to CAN module(requires CAN adapter V1.0 module). Built-in IR receiver. RJ45 port support a 100Mbps wired network, built-in 2.4G Wifi module, supports 100Mbps wireless network, users can connect the inlculde wifi antenna to get a stronger and more stable Wifi signa.
- Flexible Power Support USB-C 5V power supply and DC12V-24V from a 3D Printer, making it easy and efficient to power up the board without any extra adapters or power soucres.
- See more on Amazon...
Brand: BIGTREETECH | Manufacturer: BIGTREETECH
Dimensions: 0.39 x 3.30 x 2.20 inches
See On Amazon #3
BIGTREETECH DIRECT 1PCS TMC2209 V1.3 UART Stepper Motor Driver Module VS TMC2100 TMC2130 for Octopus V1.1/Octopus Pro/SKR V1.4 Turbo/SKR 3/Manta M4p/M5P/M8P 3D Printer Controller Board
Asin: B07ZPV4HFP | Model: TMC2209 V1.3 | PartNumber: TMC2209 V1.3 | Ean: 0787794452214 | UPC: 787794452214
ăExcellent Heat DissipationăBigtreetehc Tmc2209 Stepper Motor Driver Adopts Coolstep Current Dynamic Control, Which Can Save 75% Energy. The Sinusoidal Control Can Be Perfectly Realized Even In The System With Limited Pulse Frequency. Reduce The Heat Generated By The Stepper Motor, Thereby Reducing Cooling Requirements..
ăSatisfying Customer ServicesăIf You Have Any Problems Regarding Our Btt Tmc2209 V1.3 Drivers Stepsticks, Please Feel Free To Contact Us Via Amazon Message, Or Search Bigtreetech At Github..
ăSupports Uart, Step/Dir ModesăBigtreetech 4Pcs Tmc2209 V1.3 Uart Stepper Motors Support Uart, Step/ Dir Mode, Except That You Need To Modify The Firmware For The Mode You Use. Btt Tmc2209 V1.3 Compatible With Most 3D Printer Motherboards On The Market, Such As Btt Octopus V1.1/Octopus Pro, Skr V1.4 Turbo/Skr 3, Manta M4p/M5p/M8p, Mks Gen L...Etc 3D Printer Board.
ăSensorless HomingăThe Btt Tmc2209 Stepper Motor Driver Incorporated Stallguard4 Locked Motor Technology To Detect Alterations In The Motor Current And Use This Measurement To Detect The End Of An Axis' Stroke And Produce 3D Printers Without Limit Switches..
Features
- Ultra-quiet Stepper Driver Thanks to StealthChop2 ultra-quiet technology, BIGTREETECH TMC2209 V1.3 stepper motor driver allows for silent motor operation. The TMC2209 drivers work with a continuous current up to 2.0A, peaks of 2.8A. The voltage range from 4.75V to 28V.
- Sensorless Homing The BTT TMC2209 stepper motor driver incorporated Stallguard4 locked motor technology to detect alterations in the motor current and use this measurement to detect the end of an axis' stroke and produce 3D printers without limit switches.
- Excellent Heat Dissipation BIGTREETEHC TMC2209 stepper motor driver adopts CoolStep current dynamic control, which can save 75% energy. The sinusoidal control can be perfectly realized even in the system with limited pulse frequency. Reduce the heat generated by the stepper motor, thereby reducing cooling requirements.
- Supports UART, STEP/DIR Modes BIGTREETECH 4PCS TMC2209 V1.3 UART stepper motors support UART, STEP/ DIR Mode, except that you need to modify the firmware for the mode you use. BTT TMC2209 v1.3 compatible with most 3D printer motherboards on the market, such as BTT Octopus v1.1/Octopus pro, SKR V1.4 turbo/SKR 3, Manta M4P/M5P/M8P, MKS Gen L...etc 3d printer board
- Satisfying Customer Services If you have any problems regarding our BTT TMC2209 V1.3 Drivers stepsticks, please feel free to contact us via Amazon message, or search BIGTREETECH at GitHub.
- See more on Amazon...
Brand: BIGTREETECH Direct | Manufacturer: BIGTREETECH Direct
See On Amazon #4
BIGTREETECH EZ2209 V1.0 Stepper Motor Driver 5PCS Stepstick Mute EZ2209 Compatible with SKR 3 EZ Manta E3 EZ 3D Printer Controller Main Board
Asin: B0BRZ7QSWJ
đĄăA Breeze To Installă The Pinless Structure Of Ez2209 Stepper Driver Can Protects You From Finger Prick. Moreover, Its Anti-Misplugging Design Ensures You To Insert The Driver In A Correct Direction And Removes You From Dangers Caused By Driver Misplugging. Tip: It Is Necessary To Use Ez Driver Connector If You Want To Use Ez Drivers In Non-Ez Design Motherboard..
đĄăDurableă Ez2209 Stepper Motor Driver Is Made Of 4 Layers Pcb For Superior Performanceand A Longer Service Life. We Offer Long-Term After-Sales Guarantee For 12 Months. If You Have Difficulties In Using Our Step Driver, Please Feel Free To Contact Us, We Are Always Ready For Help..
đĄăUltra Silentă Ez2209 Stepper Motor Driver Adopts Stealthchop2 Mute Technology Which Reduces Motor Noise To The Point Of Silence At Low Velocities To Ensures Noiseless Operation, Maximum Efficiency And Best Motor Torque..
đĄăBetter Heat Dissipationă An Innovative 2 In 1 Combination Of Stepper Driver And New Large Aluminum Heat Sink Enables Ez2209 Stepper Driver Better Heat Dissipation, Declining Energy Consumption To A Minimum As Well As Protecting The Driver Chip From External Damage..
Features
- Wide Application Size: 18.5*19.8 mm, drive current 1.6A, peak current 2A, voltage range12 V- 24 V, 256 subdivision. BTT EZ2209 stepper motor driver can directly use with Mnata E3 EZ and SKR 3 EZ motherboard. EZ2209 can also well-matched with I3 Mega, Octopus V1.2, SKR 3 and other popular main boards by using BTT EZ driver connector.
- Better heat dissipation An innovative 2 in 1 combination of stepper driver and new large aluminum heat sink enables EZ2209 stepper driver better heat dissipation, declining energy consumption to a minimum as well as protecting the driver chip from external damage.
- A Breeze to Install The pinless structure of EZ2209 stepper driver can protects you from finger prick. Moreover, its anti-misplugging design ensures you to insert the driver in a correct direction and removes you from dangers caused by driver misplugging. Tip: it is necessary to use EZ driver connector if you want to use EZ drivers in non-EZ design motherboard.
- Ultra Silent EZ2209 stepper motor driver adopts stealthChop2 Mute technology which reduces motor noise to the point of silence at low velocities to ensures noiseless operation, maximum efficiency and best motor torque.
- Durable EZ2209 stepper motor driver is made of 4 layers PCB for superior performanceand a longer service life. We offer long-term after-sales guarantee for 12 months. If you have difficulties in using our step driver, please feel free to contact us, we are always ready for help.
- See more on Amazon...
Brand: BIQU | Manufacturer: BIQU
See On Amazon #5
BIGTREETECH Manta E3EZ + CB1 V2.2 + 5Pcs EZ2209 Kit Support Running Klipper Firmware Silent Control Board Kit for Ender-3 V2, Ender-3 Pro, Ender-3, BIQU B1 3D Printers
Asin: B0C6LLFBN5 | Model: KINGPRINT-1029549 | PartNumber: KINGPRINT-1029549
The Bigtreetech Manta E3 Ez Main Control Board And Core Board Use Btb Connection, Which Can Be Perfectly Paired With The Bigtreetech Cb1 Core Board..
Bigtreetech Ez2209 Using A New Customized Heat Sink, While Enhancing The Heat Dissipation Capacity, It Protects The Driver Chip From External Damage; The Newly Developed Board Frame Is Used To Match The New Connector To Improve The User Experience..
Bigtreetech Cb1 Is Equipped With Quad Core 64 Bit Arm Cortex-A53 @ 1.5Ghz Processor, 1Gb Ddr3 Memory Chip; Onboard 100M Ethernet Interface And Supports Wifi Transmission..
Manta E3ez Adopts Arm Cortex-M0+Series Stm32g0b1re Master Chip With 32-Bit Main Frequency Of 64Mhz; The Maximum Power Supply Of The Motor Is 56V;.
Features
- This kit includes BIGTREETECH Manta E3EZ silent control board, CB1 V2.2 core control board, and 5PCS EZ2209 stepper motor drivers.
- Manta E3EZ adopts ARM Cortex-M0+series STM32G0B1RE master chip with 32-bit main frequency of 64MHz; The maximum power supply of the motor is 56V;
- The BIGTREETECH Manta E3 EZ main control board and core board use BTB connection, which can be perfectly paired with the BIGTREETECH CB1 core board.
- BIGTREETECH CB1 is equipped with quad core 64 bit ARM Cortex-A53 @ 1.5GHz processor, 1GB DDR3 memory chip; Onboard 100M Ethernet interface and supports WIFI transmission.
- BIGTREETECH EZ2209 using a new customized heat sink, while enhancing the heat dissipation capacity, it protects the driver chip from external damage; The newly developed board frame is used to match the new connector to improve the user experience.
- See more on Amazon...
Brand: BIGTREETECH | Manufacturer: BIGTREETECH
See On Amazon #6
BIGTREETECH Octopus Pro V1.1 H723 32 bit Control Board 550MHz Support 8 Axis Stepper Motor Drivers TMC2209 Klipper/Marlin High-Speed/Voltage Printing Support Raspberry Pi Octprint Operating Systems
Asin: B0BM3BFZ35 | Model: US-1020000408 | PartNumber: US-1020000408
ăđStepper Motor UpgradedăSupport 8 Axis Powerful Motor Driver, Support 5V Level For Stepper Motor Driver, Better Performance. Support Max 60V Motor Input Voltage To Inprove Motor Power, Reduce Pulse Losing. Support Step/Dir/Uart/Spi Mode, Such As Tmc2209. Tmc2208, Tmc5160t Pro Stepper Motor Drivers..
ă â€ïžAttationă If You Have Any Problems During Use, Please Contact Us At The First Time. We Will Give You A Satisfactory Solution..
ăđExpanded Function InterfaceăSupport Bltouch, Biqu Microprobe V2.0, Eddy V1.0 Auto Bed Leveling Sensor, Resume Printing, Wifi. Rgb Light, Sfs V2.0 Filament Runout Detection. Power Shundown, Proximity Sensor...Etc. Dsiaplay Compatible With Hdmi5 V1.1 Touchscreen/Tft35/50/70 Display. (Klipper Touch Mode,Please Choose Hdmi5 V1.1)..
ăđIncrease Motherboard Protector Level Conversion Chip ăConvert 3.3V Signal To 5V Signal, Improve Driver Performance, 8 Isolation Chips To Protector The Motherboard, Avoid Reverse Drive Insertion Or Short Circuit, The Main Control Chip Is Burnt..
ăđ Onboard Max31865 ăSupport 2/4-Wire Pt100/Pt1000 Temperature Measurement Without Welding (The Soldering Resistance Can Also Support 3-Wire Pt100/Pt1000 Temperature Measurement..
ăđAbout FirmwareăSupports Marlin And Klipper, Compatible With Btt Pi V1.2/Pi2 Or Cb1/Pi4b Adapter, The Best Choice For Klipper High-Speed/Voltage Printing, Meet The Individual Need Of Diy Users, Support Operation Systems Raspberry Pi / Octoprint..
Features
- Main Control Chip BIGTREETECH Octopus pro v1.1 h723 board adopts the ARM Cortex-M7 series, STM32H723ZET6, main frequency up to 550MHz, 512KB flash, processing is more stable and fast.
- About Firmware Supports Marlin and Klipper, compatible with BTT Pi V1.2/PI2 or CB1/Pi4b adapter, the best choice for Klipper high-speed/voltage printing, meet the individual need of DIY users, support operation systems Raspberry Pi / Octoprint.
- Stepper motor Upgraded Support 8 axis powerful motor driver, support 5V level for stepper motor driver, better performance. Support max 60V motor input voltage to inprove motor power, reduce pulse losing. Support STEP/DIR/UART/SPI Mode, such as TMC2209. TMC2208, TMC5160T Pro stepper motor drivers.
- Onboard MAX31865 Support 2/4-wire PT100/PT1000 temperature measurement without welding (the soldering resistance can also support 3-wire PT100/PT1000 temperature measurement.
- Expanded function interface Support Bltouch, biqu microprobe v2.0, eddy v1.0 auto bed leveling sensor, resume printing, Wifi. RGB light, SFS V2.0 filament runout detection. Power shundown, Proximity sensor...etc. dsiaplay compatible with HDMI5 v1.1 touchscreen/TFT35/50/70 display. (Klipper touch mode,please choose HDMI5 V1.1).
- Increase Motherboard Protector Level Conversion Chip Convert 3.3V signal to 5V signal, improve driver performance, 8 isolation chips to protector the motherboard, avoid reverse drive insertion or short circuit, the main control chip is burnt.
- Attation If you have any problems during use, please contact us at the first time. We will give you a satisfactory solution.
- See more on Amazon...
Brand: BIGTREETECH | Manufacturer: BIGTREETECH
Dimensions: 0.04 x 5.91 x 3.94 Inches
See On Amazon #7
BIGTREETECH TFT35 E3 V3.0.1 Graphic Smart Display Panel Board for Ender-3 Compatible with SKR Mini E3 V3.0, SKR 3/EZ, Octopus/Pro/Max EZ, Kraken, SKR Pro V1.2 Control Board
Asin: B08182XHZZ | Model: TFT35 E3 V3.0.1 | PartNumber: TFT35 E3 V3.0.1 | Ean: 0778601688131 | UPC: 778601688131
3ïŒReserve Wifi Port, And Wifi Function Is Realized By External Wifi ModuleïŒReserve The Extension Port Of Filament Breaking Detection (Fil-Det)ïŒ.
5ïŒLcd12864 Mode Uses Exp1, Exp2 And Exp3. Exp1 And Exp2 Are Lcd Screen Ports Of Normal Motherboard. Exp3 Is The Lcd Interface Used By E3 Series Motherboard (Such As Skr Mini E3 V1.2, Skr E3 Dip V1.1, Etc.).
4ïŒReserve The Extension Port Of Automatic Shutdown After Printing (Ps-On);.
2ïŒThis Display Board Has Higher Compatibility. Users Can Select Two Work Modes:Uart Serial Port Screen Mode And 12864 Screen Mode;Serial Port Screen Mode Supports Two Printing Modes: Sd Card And U Disk..
Features
- 1 ARM Cortex-M3 series GD32F205VCT6 chip with 32-bit CPU 120MHz; Upgrade the firmware by SD card. It is easy and convenient to operate.
- 2 This display board has higher compatibility. Users can select two work modes:UART serial port screen mode and 12864 screen mode;Serial port screen mode supports two printing modes: SD card and U disk.
- 3 Reserve WIFI port, and WIFI function is realized by external WIFI module Reserve the extension port of filament breaking detection (FIL-DET)
- 4 Reserve the extension port of automatic shutdown after printing (PS-ON);
- 5 LCD12864 mode uses EXP1, EXP2 and EXP3. EXP1 and EXP2 are LCD screen ports of normal motherboard. EXP3 is the LCD interface used by E3 series motherboard (such as SKR MINI E3 V1.2, SKR E3 DIP V1.1, etc.)
- See more on Amazon...
Brand: BIGTREETECH | Manufacturer: BIGTREETECH
See On Amazon #8
BIGTREETECH SKR PICO V1.0 Control Board Mini Controller Board with TMC2209 UART Stepper Motor and Raspberry Pi Online Printing for Voron V0 V0.1 3D Printer Motherboard
Asin: B09MYKL9MP | Model: 1060000513 | PartNumber: 1060000513
đăMute Printing & Premium CapacitorsăFeatured With Tmc2209 Mute Driver Uart Mode, Big Tree Tech Skr Pico V1.0 Supports Mute 3D Printing. The Main Version Of The Chip Capacitor (Mlcc) Adopts High-Quality Murata Capacitors To Enhance Product's Quality..
đăSatisfying After-Sales SupportsăAny Issues Or Questions About Btt Skr Pico V1.0, Please Feel Free To Contact Us Any Time On Amazon. Our Professional Technical Team're Willing To Provide You With Immediate Technical Supports As Soon As We Can..
đăUpgraded Heat DissipationăUpgrade The Design Of The Heat Sink And Increase The Heat Dissipation Area. Increased Controllable Fan Enables To Lower The Temperature Of The Whole Machine When The It's Working, Effectively Solving Problems Related To Heat Dissipation, And Improving On The Heat Dissipation..
đăPerfectly Match With Raspberry PiăBtt Skr Pico V1.0 Control Board With Raspberry Pi Board Frame, Raspberry Pi Can Be Perfectly Installed On Btt Skr Pico Mainboard, Saving Internal Spaces. The Unique Lateral Design Of Skr PicoâS Seat Perfectly Matches The Space Characteristics Of The Voron V0 And V0.1 Machine That Needs To Be Fixed To The Motherboard Longitudinally. Compatible With Btt Pi Can Running Klipper..
Features
- Brand-new Version for Voron V0& V0.1 Featured with Raspberry Pi ARM Cortex- Mo+ MCU PR2040, BIGTREETECH SKR Pico V1.0 motherboard upgraded on ID design, which coexists of stylish appearance and excellent performances, ideal choice for Voron players. The fuse kit consists of fuse and holder, which enables easy disassembling and installation. Type-C interface allows for main control communication.
- Perfectly match With Raspberry Pi BTT SKR Pico v1.0 control board with Raspberry Pi board frame, Raspberry Pi can be perfectly installed on BTT SKR Pico mainboard, saving internal spaces. The unique lateral design of SKR Pico s seat perfectly matches the space characteristics of the Voron V0 and V0.1 machine that needs to be fixed to the motherboard longitudinally. compatible with BTT PI can running Klipper.
- Mute Printing & Premium Capacitors Featured with TMC2209 mute driver UART mode, big tree tech SKR PICO V1.0 supports mute 3D printing. The main version of the chip capacitor (MLCC) adopts high-quality Murata capacitors to enhance product's quality.
- Upgraded Heat Dissipation Upgrade the design of the heat sink and increase the heat dissipation area. Increased controllable fan enables to lower the temperature of the whole machine when the it's working, effectively solving problems related to heat dissipation, and improving on the heat dissipation.
- Satisfying After-Sales Supports Any issues or questions about BTT SKR Pico V1.0, please feel free to contact us any time on Amazon. Our professional technical team're willing to provide you with immediate technical supports as soon as we can.
- See more on Amazon...
Brand: BIGTREETECH | Manufacturer: BIGTREETECH
Dimensions: 0.11 x 33.46 x 22.04 Inches | Weight: 0.28 Pounds
See On Amazon #9
BIGTREETECH SKR Mini E3 V3.0 Motherboard + TFT35 E3 V3.0.1 Touch Screen Upgrade Kit for Ender-3 Ender-3 Pro 3D Printers, BTT 32-bit Silent Main Board Onboard TMC2209, Support Marlin/Klipper
Asin: B082HBZ3BH | Model: SKR MINI | PartNumber: SKR MINI
đ„ăSuperior Heat DissipationăUpgraded Skr Mini E3 V3.0 3D Printer Control Board Is Equipped With A Larger Aluminum Heat Sink Of Stepper Motor Driver Instead Of Pieces Small Heat Sink. Such Design Increases The Heat Dissipation Performance Of Skr Mini E3 V3 By 20%..
đ„ăTwo Working ModesăTft35 E3 V3.0.1 Touch Screen Supports Uart Serial Port Screen Mode(Touch Screen Mode) And 12864 Screen Mode. It Can Replace Original Display Of Ender-3 3D Printer. You Can Enjoy Two Printing Modes: Sd Card And U Disk..
đ„ăTft35 E3 V3.0.1 Touch Screenă Appearance Size: 93*87Mm, Power Input : 5V, This Is A 3.5 Inch Full-Color Screen With Ultra Clear Interface And Responsive Touch. Bigtreetech Tft35 E3 V3.0.1 Display Is Designed For Ender-3 3D Printer Especially, Which Can Be A Drop-In Replacement For Its Original Lcd Screen..
đ„ăDiy Friendly MainboardăBtt Skr Mini E3 V3.0 Motherboard Supports Bltouch, Rgb Lights, Blocking Detection And Shutdown Function. Our Skr Mini E3 V3 Also Supports Tft35 E3 V3.0.1/Tft35 V3.0.1/Tft28 V3.0 Touch Screen As Well As Original 12864 Lcd Screen..
Features
- Born for Ende-3 Series Printers Both BIGTREETECH SKR Mini E3 V3.0 mainboard and TFT35 E3 V3.0.1 touch screen are drop-in replacements for Ender-3 (same mouting holes, need to download firmware from GitHub web for update). And they are also compatible with Ende-3 pro, Ender-5, Ender-5 pro 3D printers.
- DIY Friendly Mainboard BTT SKR Mini E3 V3.0 motherboard supports BLTouch, RGB lights, blocking detection and shutdown function. Our SKR Mini E3 V3 also supports TFT35 E3 V3.0.1/TFT35 V3.0.1/TFT28 V3.0 touch screen as well as original 12864 LCD screen.
- Superior Heat Dissipation Upgraded SKR MINI E3 V3.0 3d printer control board is equipped with a larger aluminum heat sink of stepper motor driver instead of pieces small heat sink. Such design increases the heat dissipation performance of SKR Mini E3 V3 by 20%.
- TFT35 E3 V3.0.1 Touch Screen Appearance size: 93*87mm, power input : 5V, this is a 3.5 inch full-color screen with ultra clear interface and responsive touch. BIGTREETECH TFT35 E3 V3.0.1 display is designed for ender-3 3d printer especially, which can be a drop-in replacement for its original LCD screen.
- Two Working Modes TFT35 E3 V3.0.1 Touch screen supports UART serial port screen mode(touch screen mode) and 12864 screen mode. It can replace original display of Ender-3 3D printer. You can enjoy two printing modes: SD card and U disk.
- See more on Amazon...
Brand: BIQU | Manufacturer: BIQU
See On Amazon #10
BIGTREETECH SKR V1.4 Control Board 32bit Upgrade SKR V1.3 Motherboard, Compatible TFT35/TFT35 E3/TFT70 Touch Screen Mini12864 LCD Support TMC2209/EZ2209/TMC2208/TMC5160 for Most FDM 3D Printer
Asin: B0BHNVFR1M | Model: KINGPRINTER-1020000399 | PartNumber: KINGPRINTER-1020000399
âSupport 2.4, 2.8, 3.5-Inch Color Touch Screen, Support Lcd2004 Screen, Lcd12864 Screen; Upgrade Configuration Firmware Through Sd Card, Simple, Convenient And Efficient Operation..
âOn-Board Tmc Driver Spi Working Mode And Uart Working Mode, And The On-Board Diag Function Pins Are Convenient For Customers To Use, Eliminating The Complicated Wiring Process, Which Can Be Used By Simply Removing And Inserting The Jumper Cap; Functions Such As Continuous Power On, Material Detection, Shutdown After Power Off..
âIt Can Supply Power To Tft Screen, Bltouch, Neo-Pixel By Plugging In An External Dc5v Power Module; In Addition, I2c, Spi, Wifi Interface Is Reserved To Facilitate Customer Diy..
âEquipped With Highly Modular Open Source Firmware Marlin 2.0, Which Is Convenient For Users To Diy And Secondary Development..
Features
- Using 32-bit 100MHz ARM-class Cortex-M3 series LPC1768 main control chip, the performance is greatly improved.
- Equipped with highly modular open source firmware Marlin 2.0, which is convenient for users to DIY and secondary development.
- Support 2.4, 2.8, 3.5-inch color touch screen, support LCD2004 screen, LCD12864 screen; Upgrade configuration firmware through SD card, simple, convenient and efficient operation.
- It can supply power to TFT screen, BLtouch, Neo-pixel by plugging in an external DC5V power module; in addition, I2C, SPI, WIFI interface is reserved to facilitate customer DIY.
- On-board TMC driver SPI working mode and UART working mode, and the on-board DIAG function pins are convenient for customers to use, eliminating the complicated wiring process, which can be used by simply removing and inserting the jumper cap; Functions such as continuous power on, material detection, shutdown after power off.
- See more on Amazon...
Brand: BIGTREETECH | Manufacturer: BIGTREETECH
See On Amazon ï»ż
Looking For Something Else?
Search