AURSINC Latest OSTAR MMDVM Hotspot Spot Radio WiFi Digital Voice Modem Work UHF VHF Dual Band | Support DMR D-Star System Fusion FCS YSFReflector P25 NXDN Pocsage Networks
Asin: B0BP1TT1W1 | Model: OSTAR MMDVM | PartNumber: OSTAR MMDVM
As an Amazon Associate we earn a fee from qualifying purchases when you follow a link to Amazon from this page. We rank the products, but the links to Amazon are promotional.Easy To Use: Very Easy To Use, Works Without A Computer. No Additional Hardware Required, Works Out Of The Box. All Accessories Included. Web Interface For Configuration And Monitoring. Runs Fully Embedded Software, Running On An Openwrt Operating System. No Tf Card, Bulky Windows Software Or Failing Sd Cards..
Note: Connect The Power Of Usb, If Rf Board’S Led Did Not Flash All On, Only Pwr Led On, Disconnect The Power And Connect Again Until All Led Flash. (Try Less Than 5 Times Will Work). Any Other Problem Just Press Wps Key To Factory Reset.
Instructions: For Product Instructions, Please Download The User Manual In The "Product Guide And Documents" Section Of The Product Description. For More Info About Ostar Usage Instructions, Please View : "Mmdvm.Club/Index.Php/Ostar.Html" If You Have Any Technical Problems During The Use Of The Product, Please Contact Us..
Power Saving And Safe: Usb Powered, Low Energy Consumption, 10Mw Rf Output. Free Micro Usb Charging Cable Included, Charged With Power Bank Or Connect To Laptop Or Computer. The Hotspot Will Also Work Mobile In Your Vehicle If You Tether It To Your Mobile Phone Network..
Widely Compatible: Supports Dmr (Brandmeister), D-Star , System Fusion (Fcs, Ysfreflector), P25 , Nxdn ,Pocsage Networks..
Features
- Latest Feature: TF is not required for this hotspot, the main board is the latest design by our team -- jumbospot. Power up boot time: under 30s; Runs without an SD card; USB/WEB update Firmware; USB Console Function; Simple Setting Page; Simple Log View Function; System Firmware Size: Max 32M; Running Current: Under 300ma @5V; Factory Reset WPS button.
- Widely Compatible: Supports DMR (Brandmeister), D-Star , System Fusion (FCS, YSFReflector), P25 , NXDN ,Pocsage networks.
- Easy to Use: Very easy to use, works without a computer. No additional hardware required, works out of the box. All accessories included. Web interface for configuration and monitoring. Runs fully embedded software, running on an openwrt operating system. No TF card, bulky Windows software or failing SD cards.
- Power Saving and Safe: USB powered, low energy consumption, 10mW RF output. Free micro USB charging cable included, charged with power bank or connect to laptop or computer. The Hotspot will also work mobile in your vehicle if you tether it to your mobile phone network.
- NOTE: Connect the Power of USB, if RF board s led did not Flash ALL ON, only PWR LED ON, disconnect the Power and Connect Again Until All LED Flash. (Try less than 5 times will work). Any other problem just Press WPS key to factory reset
- Instructions: for product instructions, please download the user manual in the Product Guide and Documents section of the product description. For more info about OSTAR usage instructions, please view : mmdvm.club/index.php/ostar.html If you have any technical problems during the use of the product, please contact us.
- See more on Amazon...
Brand: AURSINC | Manufacturer: AURSINC
Dimensions: 0.70 x 2.00 x 0.70 inches
Warranty: 1 year manufacturer
See On Amazon Similar To AURSINC Latest OSTAR MMDVM Hotspot
#1
AURSINC MMDVM Hotspot Board (V1.5.2) + Antenna Support UHF VHF Support P25 DMR YSF DSTAR NXDN POCSAG for Raspberry Pi-Zero W, Pi 3 (OLED Board)
Asin: B07VW819NW | Model: 202007 | PartNumber: 202007 | Ean: 0753318592445 | UPC: 753318592445
[Multifunction] Hotspot Board Saves Electricity, High Quality Tcxo, Stable, Low Ber. Support Mmdvm Mode Dmr / Ysf / P25 / Nxdn / Dstar / Pocsag. Support Online Upgrade, User-Friendly Oled And Nextion Special Design Location, Reserved For Additional Installation Of Bluetooth Modules.
[Compatible With P4 Settings] Since Our Mmdvm Board Is Defautly Setup For Pi-Zero W, Pi 3. And If You Do Want To Connect It With Your Pi 4, You Could Try Below Methods. Pick One. Method 1: Remove The R1 Resistance Of The Hotspot Board(Single/Dual) ; Method 2: Cut Off The 2 Raspberry Pi Pin Headers On The Corners Of The Board ( Pick One To Operate On Your Mmdvm Board, Refer To The Product Image For The R1 And 2 Pin Headers Locations).
[Note] If The Raspberry Fails To Connect The Hotspot Board, Please Try Update The Firmware Of The Hotspot Board By Conducting The Command: Sudo Pistar-Mmdvmhshatflash Hs_Hat. More Info Pls View: Amateurradionotes.Com/Pi-Star-Notes.Htm#Hotspotfwupdate..
[Applicability] Aursinc Hotspot Board Supports Raspberry Pi 3B, 3B +, Pi Zero, Compatible With Nanopi Neo, Orange Pi, Compatible With Bluedv (Requires Usbtottl Or Bluetooth Model). If You Want A Little Processor Power Install On Pi 3 Or Pi4, This Is A Great Little Hat For Digital Voice Modes..
Features
- [Frequency Range] MMDVM hotspot supports UHF VHF, frequency range: 144MHz-148MHz, 420MHz-475MHz, 842MHz-950MHz (depending on ADF7021 and TCXO, HAT firmware amateur radio brand license restrictions)
- [Applicability] AURSINC hotspot board supports Raspberry Pi 3B, 3B +, Pi ZERO, compatible with NanoPi NEO, Orange Pi, compatible with BlueDV (requires USBtoTTL or Bluetooth model). if you want a little processor power install on Pi 3 or Pi4, this is a great little hat for digital voice modes.
- [Multifunction] Hotspot board saves electricity, High quality TCXO, stable, low BER. Support MMDVM mode DMR / YSF / P25 / NXDN / DSTAR / POCSAG. Support online upgrade, User-friendly OLED and Nextion special design location, reserved for additional installation of Bluetooth modules
- [Note] If the Raspberry fails to connect the hotspot board, please try update the firmware of the hotspot board by conducting the command: sudo pistar-mmdvmhshatflash hs_hat. More info pls view: amateurradionotes.com/pi-star-notes.htm#hotspotfwupdate.
- [Compatible with P4 settings] since our mmdvm board is defautly setup for Pi-Zero W, Pi 3. and if you do want to connect it with your Pi 4, you could try below methods. PICK ONE. Method 1: Remove the R1 resistance of the hotspot board(single/dual) ; Method 2: Cut off the 2 Raspberry Pi pin headers on the corners of the board ( pick one to operate on your MMDVM board, refer to the product image for the R1 and 2 pin headers locations)
- See more on Amazon...
Brand: AURSINC | Manufacturer: AURSINC
Dimensions: 1.18 x 3.94 x 2.76 inches
See On Amazon #2
AURSINC MMDVM Hotspot Board (V1.5.2) + Antenna + OLED Display Aluminium Case Support UHF C4FM YSF NXDN DSTAR P25 DMR Fully Assembled and Tested (Raspberry pi not Included)
Asin: B07Z8YP5VJ | Ean: 0753318592575 | UPC: 753318592575
[Multifunction] Hotspot Board Saves Electricity, High Quality Tcxo, Stable, Low Ber. Support Mmdvm Mode Dmr / Ysf / P25 / Nxdn / Dstar / Pocsag. Support Online Upgrade, User-Friendly Oled And Nextion Special Design Location, Reserved For Additional Installation Of Bluetooth Modules.
[Note] If The Raspberry Fails To Connect The Hotspot Board, Please Try Update The Firmware Of The Hotspot Board By Conducting The Command: Sudo Pistar-Mmdvmhshatflash Hs_Hat.
[Compatible With P4 Settings] Since Our Mmdvm Board Is Defautly Setup For Pi-Zero W, Pi 3. And If You Do Want To Connect It With Your Pi 4, You Could Try Below Methods. Pick One. Method 1: Remove The R1 Resistance Of The Hotspot Board(Single/Dual) ; Method 2: Cut Off The 2 Raspberry Pi Pin Headers On The Corners Of The Board ( Pick One To Operate On Your Mmdvm Board, Refer To The Product Image For The R1 And 2 Pin Headers Locations).
[Applicability] Aursinc Mmdvm Hotspot Board Supports Raspberry Pi 3B, 3B +, Pi Zero, Pi Zero 2W, Compatible With Nanopi Neo, Orange Pi, Compatible With Bluedv (Requires Usbtottl Or Bluetooth Model). Great Way To Roll Your Own Hotspot. Added A Pi Zero 2W, Power Supply, Microsd, And Loaded With Wpsd. You Will Have A Great Simple Hotspot. Great Way To Help Learn About Dmr.
Features
- [Frequency Range] MMDVM hotspot supports UHF VHF, frequency range: 144MHz-148MHz, 420MHz-475MHz, 842MHz-950MHz (depending on ADF7021 and TCXO, HAT firmware amateur radio brand license restrictions)
- [Applicability] aursinc mmdvm hotspot board supports Raspberry Pi 3B, 3B +, Pi ZERO, Pi Zero 2W, compatible with NanoPi NEO, Orange Pi, compatible with BlueDV (requires USBtoTTL or Bluetooth model). Great way to roll your own hotspot. Added a Pi Zero 2W, power supply, microSD, and loaded with WPSD. You will have a great simple hotspot. Great way to help learn about DMR
- [Multifunction] Hotspot board saves electricity, High quality TCXO, stable, low BER. Support MMDVM mode DMR / YSF / P25 / NXDN / DSTAR / POCSAG. Support online upgrade, User-friendly OLED and Nextion special design location, reserved for additional installation of Bluetooth modules
- [Compatible with P4 settings] since our mmdvm board is defautly setup for Pi-Zero W, Pi 3. and if you do want to connect it with your Pi 4, you could try below methods. PICK ONE. Method 1: Remove the R1 resistance of the hotspot board(single/dual) ; Method 2: Cut off the 2 Raspberry Pi pin headers on the corners of the board ( pick one to operate on your MMDVM board, refer to the product image for the R1 and 2 pin headers locations)
- [Note] If the Raspberry fails to connect the hotspot board, please try update the firmware of the hotspot board by conducting the command: sudo pistar-mmdvmhshatflash hs_hat
- See more on Amazon...
Brand: AURSINC | Manufacturer: AURSINC
Warranty: 1 YEAR
See On Amazon #3
MMDVM Duplex Hotspot Module Dual Hat with 0.96 OLED Display V1.5.2 Support P25 DMR YSF NXDN DMR Slot 1 + Slot 2 for Raspberry pi (with OLED)
Asin: B0878WF7HW | Model: 20200 | PartNumber: 20200
Work With Rasberry Pi: Mounts Cleanly On Current Raspberry Pi Including The Pi Zero, Not Compatible With Rasberry Pi 4.
Frequency: Uhf 433-900Mhz, Vhf144-146. Note: Tx =0, Rx=0. Modem Select: Stm32_Hs_Gpio ; To Leave The Screen On All The Time In Pi-Star Configuration, Ensure You Have "Oled Type 3" In The Display Type Field At The Top Of The Page, Set Port To: Modem. Also, In The Expert Section, Go To Mmdvm Host, And Scroll Down To The Oled Section. Make Sure Logoscreensaver Is Set To 1. This Leaves The Screen On All The Time. Otherwise, It Goes Blank When Idle.
Update New Fw 1.5.2 : (Pi-Star / Expert / Ssh Access / User :Pi-Star Pass:Raspberry) Then Run Sudo Pistar-Mmdvmhshatflash Hs_Dual_Hat Set Jumper Boot0=1,Boot1=0 And Soler Jp1 First! After Upgraded Finished, Disconnect Jp1.
Easy Operation: The Firmware Is Pre-Loaded And Is Easily Upgraded Via Software. Onboard Leds Showing Status (Tx, Rx, Ptt, Mode).
Widely Compatible: Supports Dmr, P-25, D-Star And System Fusion. High Performace: 32-Bit Arm Processor, Up To 10Mw Rf Power, Fully Tested Every Piece.
Features
- If the board fails to work on duplex mode, please run the upgrade command: sudo pistar-mmdvmhshatflash hs_dual_hat (if this command doesn't work, please try this command: mmdvm.club/index.php/wpsd .html)
- WIDELY COMPATIBLE: Supports DMR, P-25, D-Star and System Fusion. HIGH PERFORMACE: 32-bit ARM processor, up to 10mW RF power, fully tested every piece
- WORK with RASBERRY Pi: Mounts cleanly on current Raspberry Pi including the Pi Zero, NOT compatible with Rasberry Pi 4
- EASY OPERATION: The firmware is pre-loaded and is easily upgraded via software. Onboard LEDs showing status (Tx, Rx, PTT, Mode)
- FREQUENCY: UHF 433-900MHz, VHF144-146. NOTE: TX =0, RX=0. Modem select: STM32_HS_GPIO ; To leave the screen on all the time In Pi-Star configuration, ensure you have OLED Type 3 in the display type field at the top of the page, set Port to: modem. Also, in the Expert section, go to MMDVM host, and scroll down to the OLED section. Make sure LogoScreensaver is set to 1. This leaves the screen on all the time. Otherwise, it goes blank when idle
- Update new FW 1.5.2 : (pi-star / expert / ssh access / user :pi-star pass:raspberry) then run sudo pistar-mmdvmhshatflash hs_dual_hat set Jumper BOOT0=1,BOOT1=0 and soler JP1 First! After upgraded finished, disconnect JP1
- See more on Amazon...
Brand: AURSINC | Manufacturer: AURSINC
See On Amazon #4
AURSINC MMDVM Hotspot Board (V1.5.2) + Antenna Support UHF VHF Support P25 DMR YSF DSTAR NXDN POCSAG for Raspberry Pi-Zero W, Pi 3
Asin: B0816LQP8T | Ean: 0753318592698 | UPC: 753318592698
Mmdvm Board Saves Electricity, High Quality Tcxo, Stable, Low Ber. Support Mmdvm Mode Dmr / Ysf / P25 / Nxdn / Dstar / Pocsag.
Packing List: 1X Mmdvm Hotspot Board(Uhf/Vhf), 1X Antenna, 1X Elbow.
Support Online Upgrade, User-Friendly Oled And Nextion Special Design Location, Reserved For Additional Installation Of Bluetooth Modules.
Hotspot Board Support Raspberry Pi 3B, 3B +, Pi Zero, Compatible With Nanopi Neo, Orange Pi, Compatible With Bluedv (Requires Usb To Ttl Or Bluetooth Model).
Features
- MMDVM hotspot board is the latest firmware. Supports UHF VHF, frequency range: 144MHz-148MHz, 420MHz-475MHz, 842MHz-950MHz (depending on ADF7021 and TCXO, HAT firmware amateur radio brand license restrictions)
- Hotspot board support Raspberry Pi 3B, 3B +, Pi ZERO, compatible with NanoPi NEO, Orange Pi, compatible with BlueDV (requires USB to TTL or Bluetooth model)
- MMDVM board saves electricity, High quality TCXO, stable, low BER. Support MMDVM mode DMR / YSF / P25 / NXDN / DSTAR / POCSAG
- Support online upgrade, User-friendly OLED and Nextion special design location, reserved for additional installation of Bluetooth modules
- Packing list: 1x mmdvm hotspot board(UHF/VHF), 1x antenna, 1x elbow
- See more on Amazon...
Brand: AURSINC | Manufacturer: AURSINC
Dimensions: 0.40 x 2.56 x 1.20 inches
Warranty: 3 mouth
See On Amazon #5
MMDVM Duplex Hotspot Module Dual Hat V1.5.2 Support P25 DMR YSF NXDN DMR Slot 1 + Slot 2 for Raspberry pi with USB Port (with OLED)
Asin: B089K195T2 | Model: 2020 | PartNumber: 2020 | Ean: 0753318593275 | UPC: 753318593275
Work With Rasberry Pi: Mounts Cleanly On Current Raspberry Pi Including The Pi Zero , Not Compatible With Rasberry Pi 4..
The Mmdvm Duplex Hotspot Board Is Latest Firmware V1.5.2. How To Update Firmware: (Pi-Star / Expert / Ssh Access / User :Pi-Star Pass:Raspberry) Then Run Sudo Pistar-Mmdvmhshatflash Hs_Dual_Hat Set Jumper Boot0=1,Boot1=0 And Soler Jp1 First! After Upgraded Finished, Disconnect Jp1 (After Testing, This Method Can Upgrade The Firmware).
Frequency: Radio Frequency : Freq:144-148,219-225, (Main Band) 420-475,842-950 Note: Tx =0, Rx=0. Modem Select: Stm32-Dvm/Mmdvm_Hs-Raspberry Pi Hat(Gpio) Or Any Other (Gpio Board).
Widely Compatible: Supports Dmr, P-25, D-Star And System Fusion. High Performace: 32-Bit Arm Processor, Up To 10Mw Rf Power, Fully Tested Every Piece.
Features
- if the board fails to work on duplex mode, please run the upgrade command: sudo pistar-mmdvmhshatflash hs_dual_hat (if this command doesn't work, please try this command: mmdvm.club/index.php/wpsd .html)
- WIDELY COMPATIBLE: Supports DMR, P-25, D-Star and System Fusion. HIGH PERFORMACE: 32-bit ARM processor, up to 10mW RF power, fully tested every piece
- WORK with RASBERRY Pi: Mounts cleanly on current Raspberry Pi including the Pi Zero , NOT compatible with Rasberry Pi 4.
- FREQUENCY: Radio Frequency : Freq:144-148,219-225, (Main Band) 420-475,842-950 NOTE: TX =0, RX=0. Modem select: STM32-DVM/MMDVM_HS-Raspberry pi Hat(GPIO) or any other (GPIO board)
- The MMDVM Duplex Hotspot board is latest firmware V1.5.2. How to update firmware: (pi-star / expert / ssh access / user :pi-star pass:raspberry) then run sudo pistar-mmdvmhshatflash hs_dual_hat set Jumper BOOT0=1,BOOT1=0 and soler JP1 First! After upgraded finished, disconnect JP1 (After testing, this method can upgrade the firmware)
- See more on Amazon...
Brand: AURSINC | Manufacturer: AURSINC
See On Amazon #6
MMDVM Hotspot Spot Radio WiFi Digital Voice Modem Work Contained with Raspberry Pi Zero W with Firmware V4.1.5 UHF VHF | Ethernet Cable | Supports C4FM YSF NXDN DSTAR P25 DMR
Asin: B088PP3TVR | Ean: 0753318593213 | UPC: 753318593213
[Easy Set Up] Preload Sofeware Pi-Star On Tf Card, No Need To Download Again. Cover More Frequencies, Radio Frequency (Uhf: 430-440, Vhf: 144-146). This Is Upgraded Version, Do Not Need To Set Rxoffset And Txoffset, They're Default 0.
If You Encounter That The Device Cannot Connect To Network After Setup, Please Reflash The Sd Card By Using The Firmware Package, The Path For The Package: Drive.Google.Com/File/D/1Pl8077kkevokuixhsdqvqgsh3fy8cfzf/View?Usp=Sharing If It Still Not Working, Please Reach Out To Us Through Mail, We Will Address Your Issue Asap.
[Note] Not Compatible With Baofeng Uv-5R, Baofeng Rd-5R, 5X, 5R+, 5R Plus, Etc Uv Series, Bf Series. More Product Setup Guide, Please Read The Product Manual Or Feel Free To Contact Us, We Will Reply Within 24 Hours.
[Ethernet Connection] The Unit Came With An Ethernet Connection Device The Plugs Into One Of The Micro-Usb Ports. When Plugged The Device Into Ethernet Switch It Will Easy Connected To Your Home Network Immediately. It Is The Wired Connection, And Login To The Device Using The Ip Address Assigned By Network Router.
[Easy Charging] Free Micro Usb Charging Cable Included, Charged With Power Bank Or Connect To Laptop Or Computer. The Hotspot Will Also Work Mobile In Your Vehicle If You Tether It To Your Mobile Phone Network.
[Wifi Ssid] Need The 2.4Ghz Ssid As The Pi Zero W Doesn't Support 5.8Ghz.And Wifi Will Not Work With Wep, Make Sure Your Wifi Password Type Is Wpa. Power On The Hotspot For 2 Minutes To Automatically Connect To The Network, Or Follow The Instructions To Connect The Hotspot To Your Router. After Power On 2 Minutes，Go To "Pi-Star/Admin/Configure.Php".
Features
- [Firmware 4.1.5] In the latest batches shipped to Amazon warehouse, the problem has been solved, we have preload the firmware 4.1.5. If you receive a old firmware device and there's update trouble, please do contact us, so that we can help. Our test is in DMR mode if you want to change the working mode, you need to configure it as needed Working mode parameters) . SUPPORT: C4FM YSF NXDN DSTAR P25 DMR and default work with UHF
- [WIFI SSID] Need the 2.4GHz SSID as the Pi Zero W doesn't support 5.8GHz.and WiFi will not work with WEP, make sure your WiFi Password Type is WPA. Power on the hotspot for 2 minutes to automatically connect to the network, or follow the instructions to connect the Hotspot to your router. After power on 2 minutes go to pi-star/admin/configure.php
- [EASY SET UP] Preload sofeware Pi-Star on TF card, no need to download again. Cover more frequencies, radio frequency (UHF: 430-440, VHF: 144-146). This is upgraded version, do not need to set RXOFFSET and TXOFFSET, they're default 0
- [EASY CHARGING] Free micro USB charging cable included, charged with power bank or connect to laptop or computer. The Hotspot will also work mobile in your vehicle if you tether it to your mobile phone network
- [NOTE] Not compatible with Baofeng UV-5R, Baofeng RD-5R, 5X, 5R+, 5R Plus, etc UV series, BF series. More product setup guide, please read the product manual or feel free to contact us, we will reply within 24 hours
- [ETHERNET CONNECTION] The unit came with an ethernet connection device the plugs into one of the micro-USB ports. When plugged the device into ethernet switch it will easy connected to your home network immediately. It is the wired connection, and login to the device using the IP address assigned by network router
- If you encounter that the device cannot connect to network after setup, please reflash the SD Card by using the firmware package, the path for the package: drive.google.com/file/d/1pL8077KkEVoKuIXHsdQVQgsH3FY8CFZf/view?usp=sharing if it still not working, please reach out to us through mail, we will address your issue asap
- See more on Amazon...
Brand: AURSINC | Manufacturer: AURSINC
Dimensions: 2.00 x 4.00 x 4.00 inches | Weight: 0.28 pounds
See On Amazon #7
AURSINC MMDVM Hotspot USB HAT Board for Simplex & Dual Band Hotspot & Modem RPT Hat Support DMR DSTAR BlueDV | Compatible with Windows Linux Android System | BER, DMR, TX & TCXO offset | MicroUSB Port
Asin: B09WKJPW59
Support Bluedv: Usb Hat Board Supports Bluedv Windows, Bluedv-Android, Bluedv-Ios, Bluedv-Linux Dstar | Dstar,Dmr,Fusion(Ysf, Fcs)(Only Dn Mode).
Mmdvm_Hs Firmware: The Mmdvm-Hs Hat Supports The Updated Mmdvm_Hs Firmware Running: Linux: Sudo Stm32flash -V -W Xxx.Bin /Dev/Ttyama0 | Windows: Sudo Stm32flash -V -W Xxx.Bin /Dev/Comx | Com Serial Driver Is Ch341ser （Www.Wch.Cn/Downloads/Ch341ser_Exe.Html）.
Muliti Functions: Mmdvm Board Supports Mmdvmhost/Mmdvmcal On Linux/Windows To Test The Mmdvm Hat Ber/Dmr/Tx Check Tcxo Offset | Ber Xx%.
Wide Compatibility: Aursinc Hotspot Radio Board Supports Mmdvm_Hs Hat,Mmdvm_Hs Dual Hat And Mmdvm Modem Rpt Hat(Oled Display Is Not Compatible For Now).
Features
- MMDVM hotspot board supports UHF VHF, frequency range: 144MHz-148MHz, 420MHz-475MHz, 842MHz-950MHz (depending on ADF7021 and TCXO, HAT firmware amateur radio brand license restrictions)
- Wide Compatibility: AURSINC Hotspot radio board supports mmdvm_hs hat,mmdvm_hs dual hat and mmdvm modem rpt hat(oled display is not compatible for now)
- Support Bluedv: USB Hat board supports bluedv windows, bluedv-android, bluedv-ios, bluedv-linux DSTAR | DSTAR,DMR,Fusion(YSF, FCS)(only DN mode)
- Muliti Functions: MMDVM Board supports mmdvmhost/mmdvmcal on linux/windows to test the mmdvm hat BER/DMR/TX check TCXO offset | BER XX%
- MMDVM_HS Firmware: The mmdvm-hs hat supports the updated mmdvm_hs firmware running: linux: sudo stm32flash -v -w xxx.bin /dev/ttyAMA0 | windows: sudo stm32flash -v -w xxx.bin /dev/comx | com serial driver is ch341ser www.wch.cn/downloads/CH341SER_EXE.html
- See more on Amazon...
Brand: AURSINC | Manufacturer: AURSINC
Dimensions: 0.39 x 2.36 x 1.18 inches
Warranty: 1 YEAR
See On Amazon #8
AURSINC MMDVM Hotspot Spot Radio Station WiFi Digital Voice Modem Work Contained with Raspberry Pi Zero W with Firmware V4.1.5 UHF Supports C4FM YSF POCSAG NXDN DSTAR P25 DMR
Asin: B088PPDRT7 | Model: MMDVM HOTSPOT STATION | PartNumber: MMDVM HOTSPOT STATION | Ean: 0753318593206 | UPC: 753318593206
[Wifi Ssid] Need The 2.4Ghz Ssid As The Pi Zero W Doesn't Support 5.8Ghz. And Wifi Will Not Work With Wep, Make Sure Your Wifi Password Type Is Wpa. Power On The Hotspot For 2 Minutes To Automatically Connect To The Network, Or Follow The Instructions To Connect The Hotspot To Your Router. After Power On 2 Minutes, Goto Http://Pi-Star/Admin/Configure.Php.
[Note] This Product Comes With Usb Cable. No Ethernet Cable. If You Encounter That The Device Cannot Connect To Network After Setup, Please Email Us, We Will Address Your Issue Asap. Not Compatible With Baofeng Uv-5R, Baofeng Rd-5R, 5X, 5R+, 5R Plus, Etc Uv Series, Bf Series. More Product Setup Guide, Please Read The Product Manual Or Contact Us, We Will Reply Within 24 Hours.
If You Encounter That The Device Cannot Connect To Network After Setup, Please Reflash The Sd Card By Using The Firmware Package, The Path For The Package: Drive.Google.Com/File/D/1Pl8077kkevokuixhsdqvqgsh3fy8cfzf/View?Usp=Sharing If It Still Not Working, Please Reach Out To Us Through Mail, We Will Address Your Issue Asap.
[Easy Charging] Free Micro Usb Charging Cable Included, Charged With Power Bank Or Connect To Laptop Or Computer. The Hotspot Will Also Work Mobile In Your Vehicle If You Tether It To Your Mobile Phone Network.
[Easy Set Up] Preload Sofeware Pi-Star On Tf Card, No Need To Download Again. Radio Frequency: (Uhf:430-440) This Is Upgraded Version, Do Not Need To Set Rxoffset And Txoffset, They're Default 0. Note: When You Flash The Tf Card With New Version Software, Please Do Not Copy On The Tf Card Directly, Use A Write In Tool To Write The Software On Tf Card.
Features
- [Firmware 4.1.5] In the latest batches shipped to Amazon warehouse, the problem has been solved, we have preload the firmware 4.1.5. If you receive a old firmware device and there's update trouble, please contact us, so that we can provide support and help. Our test is in DMR mode, if you want to change the working mode, you need to configure it as needed Working mode parameters. SUPPORT: C4FM YSF NXDN DSTAR P25 DMR and default work with UHF
- [EASY SET UP] Preload sofeware Pi-Star on TF card, no need to download again. Radio Frequency: (UHF:430-440) This is upgraded version, do not need to set RXOFFSET and TXOFFSET, they're default 0. Note: when you flash the TF card with new version software, please DO NOT copy on the TF card directly, use a write in tool to write the software on TF card
- [WIFI SSID] Need the 2.4GHz SSID as the Pi Zero W doesn't support 5.8GHz. And WiFi will not work with WEP, make sure your WiFi Password Type is WPA. Power on the hotspot for 2 minutes to automatically connect to the network, or follow the instructions to connect the Hotspot to your router. After power on 2 minutes, goto http://pi-star/admin/configure.php
- [EASY CHARGING] Free micro USB charging cable included, charged with power bank or connect to laptop or computer. The Hotspot will also work mobile in your vehicle if you tether it to your mobile phone network
- [NOTE] This product comes with USB Cable. No Ethernet Cable. If you encounter that the device cannot connect to network after setup, please email us, we will address your issue asap. Not compatible with Baofeng UV-5R, Baofeng RD-5R, 5X, 5R+, 5R Plus, etc UV series, BF series. More product setup guide, please read the product manual or contact us, we will reply within 24 hours
- If you encounter that the device cannot connect to network after setup, please reflash the SD Card by using the firmware package, the path for the package: drive.google.com/file/d/1pL8077KkEVoKuIXHsdQVQgsH3FY8CFZf/view?usp=sharing if it still not working, please reach out to us through mail, we will address your issue asap
- See more on Amazon...
Brand: AURSINC | Manufacturer: AURSINC
Dimensions: 3.94 x 4.33 x 1.61 inches | Weight: 0.22 pounds
Warranty: 30days
See On Amazon #9
AURSINC MMDVM Duplex Hotspot Module Dual Hat Support P25 DMR YSF NXDN DMR for Raspberry pi (Without OLED)
Asin: B08TLTF8WH | Model: AUR-002 | PartNumber: AUR-002
Work With Rasberry Pi: Mounts Cleanly On Current Raspberry Pi Including The Pi Zero , Not Compatible With Rasberry Pi 4..
Note: Our Firmware Is Comprehensive Open Source Firmware, Does Not Support New Firmware Updates..
What Is The Transmit And Receive Range Of This Hotspot? - T/R Range Is 430-440Mhz.
Frequency: Radio Frequency : Freq:144-148,219-225, (Main Band) 420-475,842-950 Note: Tx =0, Rx=0. Modem Select: Stm32-Dvm/Mmdvm_Hs-Raspberry Pi Hat(Gpio) Or Any Other (Gpio Board).
Widely Compatible: Supports Dmr, P-25, D-Star And System Fusion.
Features
- HIGH PERFORMACE: 32-bit ARM processor, up to 10mW RF power, fully tested every piece.
- WIDELY COMPATIBLE: Supports DMR, P-25, D-Star and System Fusion
- WORK with RASBERRY Pi: Mounts cleanly on current Raspberry Pi including the Pi Zero , NOT compatible with Rasberry Pi 4.
- FREQUENCY: Radio Frequency : Freq:144-148,219-225, (Main Band) 420-475,842-950 NOTE: TX =0, RX=0. Modem select: STM32-DVM/MMDVM_HS-Raspberry pi Hat(GPIO) or any other (GPIO board)
- Note: Our firmware is comprehensive open source firmware, does not support new firmware updates.
- What is the transmit and receive range of this hotspot? - T/R range is 430-440mhz
- See more on Amazon...
Brand: AURSINC | Manufacturer: AURSINC
See On Amazon
Looking For Something Else?
Search