911 motorsports - Buying Guide
Last Updated: 05/02/2024
Share on
As an Amazon Associate we earn a fee from qualifying purchases when you follow a link to Amazon from this page. We rank the products, but the links to Amazon are promotional. #1
4x4 - Floor Jack Extension - Bolt on - Fine Thread
Asin: B0B7CCPSKY | Model: Floor Jack Extension | PartNumber: Floor Jack Extension
Made In Usa - Extension Tubes Are Swaged From 1 1/2" Dom Tube. Saddle Is 1/4" A572 Steel And Everything Has A Nice Zinc Plated Finish..
Recommended Limits – 3 Ton Or Full Jack Rating W/ 6” Extension –75% Of Jack Rating W/ 11” Extension– 50% Of Jack Rating W/Both Stacked At 16” Ext..
Converts Your Floor Jack Into A Universal 1 1/2" Pin. The Saddle Alone Gives A 2" Extension, It Comes With 6" And 11" Extensions That You Can Stack To Get A Total Of 16" Above Your Floor Jack. There Are Multiple Pin Styles To Work With Different Floor Jacks. We Came Up With A 4X4 Saddle With One Side For Round Tubes And Another For Standard Frames..
Features
- **Verify your jack is correct before ordering** Check pictures to find your jack saddle style. Bolt on - Fine thread is most common, 24mm-1.5 thread. Bolt on - Coarse Thread is found on Torin & Duralast jacks. Cross pin style is used on most 1.5 ton jacks. Drop in style was used on older jacks made more than 10 years ago.
- Converts your floor jack into a universal 1 1/2 pin. The saddle alone gives a 2 extension, it comes with 6 and 11 extensions that you can stack to get a total of 16 above your floor jack. There are multiple pin styles to work with different floor jacks. We came up with a 4x4 saddle with one side for round tubes and another for standard frames.
- Made in USA - Extension tubes are swaged from 1 1/2 DOM tube. Saddle is 1/4 A572 steel and everything has a nice Zinc plated finish.
- Recommended limits 3 ton or full jack rating w/ 6 extension 75% of jack rating w/ 11 extension 50% of jack rating w/both stacked at 16 ext.
- See more on Amazon...
Brand: 911 motorsports | Manufacturer: 911 motorsports
Warranty: Read full disclaimer with included instructions. Warning - Use at your own risk! - The entire risk as to quality and performance is with the buyer. 911 Motorsports LLC shall not be liable for any injury or damage to persons or property.
See On Amazon #2
Plasma Stencil - Circle Cutter Guide - 5 pc. Kit - .430"
Asin: B00OCGZGX4
5 Pc. Kit Includes 10 Hole Sizes. 1/2", 5/8", 3/4", 1", 1 1/4", 1 1/2", 1 3/4", 2", 2 1/2", 3". The Outside Radius Acts As Bonus Sizes, Add 2" For 380/430 Sizes Add 2 1/4" For 580 Size..
Made In Usa. Laser Cut And Etched From 1/8" Cold Rolled Steel..
Quick And Accurate Circle Cutting. The Stencils Are Offset To Cut The Indicated Size From The Center Of The Plasma Arc, This Allows A Little Clearance For Easy Assembly..
Features
- Use the chart in the pictures to find your plasma cutter and drag shield diameter.
- Quick and accurate circle cutting. The stencils are offset to cut the indicated size from the center of the plasma arc, this allows a little clearance for easy assembly.
- 5 pc. kit includes 10 hole sizes. 1/2, 5/8, 3/4, 1, 1 1/4, 1 1/2, 1 3/4, 2, 2 1/2, 3. The outside radius acts as bonus sizes, add 2 for 380/430 sizes add 2 1/4 for 580 size.
- Made in USA. Laser cut and etched from 1/8 cold rolled steel.
- See more on Amazon...
Brand: 911 motorsports | Manufacturer: 911 motorsports
Dimensions: 0.62 x 8.50 x 5.00 inches
See On Amazon #3
Plasma Cutter Straight Edge & Stencil - Magnetic Holders - 2 pc.
Asin: B077YY8XD3
Each Mag Holder Has 6 Lbs. Of Pull And 3 Lbs. Shear Strength Using Neodymium Magnets.
2 Mag Holders Included & Made In U.S.A..
For Up To 1/8" Thick Straight Edge.
Allows Easy Positioning And Holds Firm To Prevent Movement While Cutting.
Features
- Holds straight edge or Plasma Stencil where a clamp won't reach
- Allows easy positioning and holds firm to prevent movement while cutting
- Each Mag Holder has 6 lbs. of pull and 3 lbs. shear strength using neodymium magnets
- For up to 1/8 thick straight edge
- 2 Mag holders included & Made in U.S.A.
- See more on Amazon...
Brand: 911 motorsports | Manufacturer: 911 motorsports
Dimensions: 1.50 x 3.00 x 1.50 inches
See On Amazon #4
Plasma Stencil - Square Cutter Guide - 5 pc. Kit - .380"
Asin: B01FL1BIEY | Model: SUVELAM | PartNumber: SUVELAM
1/4", 3/8", 1/2" Sizes Are Under Sized By .060" To Make A Tight Fitting Hole For Carriage Bolts To Be Held In Place..
Made In Usa. Laser Cut And Etched From 1/8" Cold Rolled Steel..
5 Pc. Kit Includes 10 Hole Sizes: 1/4", 3/8", 1/2",5/8", 3/4", 1", 1 1/4", 1 1/2", 1 3/4", 2". The Outside Acts As Bonus Sizes, Add 2" For 380/430 Sizes Add 21/4" For 580 Size..
The Stencils Are Offset To Cut The Indicated Size From The Center Of The Plasma Arc, This Allows A Little Clearance For Easy Assembly..
Features
- Use the chart in the pictures to find your plasma cutter and drag shield diameter.
- The stencils are offset to cut the indicated size from the center of the plasma arc, this allows a little clearance for easy assembly.
- 1/4, 3/8, 1/2 sizes are under sized by .060 to make a tight fitting hole for carriage bolts to be held in place.
- 5 pc. kit includes 10 hole sizes: 1/4, 3/8, 1/2,5/8, 3/4, 1, 1 1/4, 1 1/2, 1 3/4, 2. The outside acts as bonus sizes, add 2 for 380/430 sizes add 21/4 for 580 size.
- Made in USA. Laser cut and etched from 1/8 cold rolled steel.
- See more on Amazon...
Brand: 911 motorsports | Manufacturer: 911 motorsports
See On Amazon #5
Plasma Stencil - Tri Slot Cutter Guide - 3 pc. Kit - .380"
Asin: B01MQ6JXNM
Laser Etched Sizes, Centerline Marks And End Of Slot..
Made In Usa. Laser Cut And Etched From 1/8" Cold Rolled Steel. We Sell And Ship These Direct Using Usps..
Includes 3 Stencils For 9 Sizes: Slot Lengths Are 2, 4, Or 6 Bolt Lengths..
Stencils Are Offset To Cut A Tight Fitting Slot..
Features
- Use the chart in the pictures to find your plasma cutter and drag shield diameter.
- Stencils are offset to cut a tight fitting slot.
- Laser etched sizes, centerline marks and end of slot.
- Includes 3 stencils for 9 sizes: slot lengths are 2, 4, or 6 bolt lengths.
- Made in USA. Laser cut and etched from 1/8 cold rolled steel. We sell and ship these direct using USPS.
- See more on Amazon...
Brand: 911 motorsports | Manufacturer: 911 motorsports
Dimensions: 0.37 x 7.00 x 6.00 inches
See On Amazon #6
Holey Cross Plasma Stencil - .380" - Bolt Hole Circle Plasma Cutter Guide Template
Asin: B07BRCJW6K
1/4, 5/16, 3/8, 1/2 Bolt Holes Offset For A Loose Fit With No Clean Up.
Made In Usa. Read Description Below For More Info.
Laser Cut And Etched From 1/8" Cold Rolled Steel.
Now You Can Plasma Cut Bolt Holes When You Don't Want To Use A Drill.
Features
- Use the chart in the pictures to find your plasma cutter and drag shield size
- Now you can plasma cut bolt holes when you don't want to use a drill
- 1/4, 5/16, 3/8, 1/2 bolt holes offset for a loose fit with no clean up
- Laser cut and etched from 1/8 cold rolled steel
- Made in USA. Read description below for more info
- See more on Amazon...
Brand: 911 motorsports | Manufacturer: 911 motorsports
Dimensions: 0.12 x 5.00 x 5.00 inches
See On Amazon #7
Short Round Saddle - Floor Jack Extension - Bolt on - Fine Thread
Asin: B0CJ4CRP83 | Model: Floor Jack Extension | PartNumber: Floor Jack Extension
Made In Usa - For Up To 3 Ton Floor Jacks - Extension Tubes Are Swaged From 1 1/2" Dom Tube. Saddle Is 1/4" A572 Steel And Everything Has A Nice Zinc Plated Finish..
Check Out Our Other Products For More Options. We Have Different Saddle And Extension Length Options. Along With A Big Flat Plate And 4 Point Jack Adapter, Which Also Work With This..
Converts Your Floor Jack Into A Universal 1 1/2" Pin. The Saddle Alone Gives A 2" Extension, It Comes With A 6" Extension, 3" Round Saddle And Prothane Brand Polyurethane Jack Pad. The Pad Holds On Tight, But Easy To Remove For Normal Jack Use..
Features
- Black saddle pads are out of stock until May, currently supplying RED saddle pad**Verify your jack is correct before ordering** Check pictures to find your jack saddle style. Bolt on - Fine thread is most common, 24mm-1.5 thread. Bolt on - Coarse Thread is found on Torin & Duralast jacks. Cross pin style is used on most 1.5 ton jacks. Drop in style was used on older jacks made more than 10 years ago.
- Converts your floor jack into a universal 1 1/2 pin. The saddle alone gives a 2 extension, it comes with a 6 extension, 3 round saddle and Prothane brand polyurethane jack pad. The pad holds on tight, but easy to remove for normal jack use.
- Made in USA - For up to 3 ton floor jacks - Extension tubes are swaged from 1 1/2 DOM tube. Saddle is 1/4 A572 steel and everything has a nice Zinc plated finish.
- Check out our other products for more options. We have different saddle and extension length options. Along with a Big Flat Plate and 4 Point Jack Adapter, which also work with this.
- See more on Amazon...
Brand: 911 motorsports | Manufacturer: 911 motorsports
Warranty: Read full disclaimer with included instructions. Warning - Use at your own risk! - The entire risk as to quality and performance is with the buyer. 911 Motorsports LLC shall not be liable for any injury or damage to persons or property.
See On Amazon #8
Plasma Torch Conversion Rings for Plasma Stencils - 2pc. - .275" to .380"
Asin: B0B4KRWYK4
.275" Size Fits Ag60/Sg55 Torches -- .300" Size Fits Pt31 Torches -- .312" Size Fits Thermal Dynamics Cutmaster 42 -- .500" Size Fits Hypertherm 30 Air, Max 40/43 And 800/900 Models. Miller Ice 50/55 And 125C Torches.
Includes Two Rings, Since They Are A Consumable.
Features
- These rings slide over your plasma torch and bump it up to a common size for use with our plasma stencils
- Includes two rings, since they are a consumable
- .275 size fits AG60/SG55 torches -- .300 size fits PT31 torches -- .312 size fits Thermal Dynamics cutmaster 42 -- .500 size fits Hypertherm 30 Air, max 40/43 and 800/900 models. Miller Ice 50/55 and 125c torches
- See more on Amazon...
Brand: 911 motorsports | Manufacturer: 911 motorsports
See On Amazon #9
Plasma Stencil - Circle PRO Upgrade - Cutter Guide 5 pc. Kit - .430"
Asin: B01K163A9K
The Stencils Are Offset To Cut The Indicated Size From The Center Of The Plasma Arc, This Allows A Little Clearance For Easy Assembly..
Made In Usa. Laser Cut And Etched From 1/8" Cold Rolled Steel. We Sell And Ship These Direct Using Usps..
5 Pc. Kit Includes 10 Hole Sizes. 7/16", 9/16", 11/16", 7/8", 1 1/8", 13/8", 1 5/8", 1 7/8", 2 1/4", 2 3/4" The Outside Radius Acts As Bonus Sizes, Add 2" For 380/430 Sizes Add 21/4" For 580 Size..
These Fill In The Gaps And Add More Sizes To The Original Circle Plasma Stencils.
Features
- Use the chart in the pictures to find your plasma cutter and drag shield diameter.
- These fill in the gaps and add more sizes to the original Circle Plasma Stencils
- The stencils are offset to cut the indicated size from the center of the plasma arc, this allows a little clearance for easy assembly.
- 5 pc. kit includes 10 hole sizes. 7/16, 9/16, 11/16, 7/8, 1 1/8, 13/8, 1 5/8, 1 7/8, 2 1/4, 2 3/4 The outside radius acts as bonus sizes, add 2 for 380/430 sizes add 21/4 for 580 size.
- Made in USA. Laser cut and etched from 1/8 cold rolled steel. We sell and ship these direct using USPS.
- See more on Amazon...
Brand: 911 motorsports | Manufacturer: 911 motorsports
Dimensions: 0.01 x 16.00 x 7.00 inches
See On Amazon #10
Big Flat Plate - Jack Adapter - Fine Thread
Asin: B0CVR384SF | Model: Big Flat Plate | PartNumber: Big Flat Plate
This Is A Cheaper Alternative To Our 4-Point Jack Adapter And Gives A Lower Profile. It Only Adds 2" To Your Jack Height When Working Underneath Vehicles On The Ground Or On Jack Stands. Good For Transmissions, Fuel Tanks, And Even As A Motorcycle Lift..
-- Made In Usa --.
**Look At Chart In Pics To Confirm Your Jack's Mount Style** The Big Flat Plate Requires Replacing The Stock Saddle With Our 1 1/2" Adapter Pin. If Adding This To A 911 Motorsports Floor Jack Extension Select "Already Have Adapter Pin"..
Features
- The Big Flat Plate measures 8"x10" and is made from 1/8" thick steel with a 1 1/2" DOM gusseted receiver tube. It comes fully welded and has a nice zinc-plated finish. There are holes on the corners and support gussets underneath for strap hooks.
- **Look at chart in pics to confirm your jack's mount style** The Big Flat Plate requires replacing the stock saddle with our 1 1/2 adapter pin. If adding this to a 911 Motorsports Floor Jack Extension select Already have adapter pin.
- This is a cheaper alternative to our 4-point Jack Adapter and gives a lower profile. It only adds 2 to your jack height when working underneath vehicles on the ground or on jack stands. Good for transmissions, fuel tanks, and even as a motorcycle lift.
- -- Made in USA --
- See more on Amazon...
Brand: 911 motorsports | Manufacturer: 911 Motorsports
Dimensions: 2.00 x 10.00 x 8.00 inches | Weight: 2.00 Pounds
Warranty: Read full disclaimer with included instructions. Warning - Use at your own risk! - The entire risk as to quality and performance is with the buyer. 911 Motorsports LLC shall not be liable for any injury or damage to persons or property.
See On Amazon #11
Rocker Switch Plasma Stencil - .380" - Rectangular Plasma Cutter Guide Template
Asin: B07BRFXGTC
Actual Cut Dimensions: Small .46" X 1.13" Big .85" X 1.47".
Center Line And Edge Of Cut Marks Allow Layout Multiple Ways.
Laser Cut And Etched From 1/8" Cold Rolled Steel.
Small Rocker 1/2" X 1 1/8" And Big Rocker 7/8" X 1 1/2".
Features
- Designed for the most common rocker switches around
- Small rocker 1/2 x 1 1/8 and big rocker 7/8 x 1 1/2
- Actual cut dimensions: small .46 x 1.13 big .85 x 1.47
- Laser cut and etched from 1/8 cold rolled steel
- Center line and edge of cut marks allow layout multiple ways
- See more on Amazon...
Brand: 911 motorsports | Manufacturer: 911 motorsports
Dimensions: 0.12 x 6.00 x 2.00 inches
See On Amazon #12
Offset Blocks - 2pc. for Plasma Cutter Straight Edge/guide - .380" - Red
Asin: B08GN4H9BY
Use The Pictured Chart Or Measure Your Drag Shield/Nozzle Diameter.
Made In Usa. 3D Printed. Read Description Below For More Information.
They Have Two Sides And Are Offset According To The Diameter Of Your Drag Shield/Nozzle.
Features
- The plasma cutter Offset Blocks allow you to make precise straight cuts with your hand-held torch
- They have two sides and are offset according to the diameter of your drag shield/nozzle
- Use the pictured chart or measure your drag shield/nozzle diameter
- Made in USA. 3D printed. Read description below for more information
- See more on Amazon...
Brand: 911 motorsports | Manufacturer: 911 motorsports
Dimensions: 0.75 x 1.50 x 2.00 inches
See On Amazon #13
30"x 16" Plasma Cutter - Water Table Conversion Kit - Edge Clamp
Asin: B0C4ZP48QG
Clamp Option - 5/8" Post For Fixture/Weld Tables. Edge Clamp Style For Our Table & Standard Fab. Tables Up To 9/16" Thick. The Clamp Is Perfect For Holding Our Plasma Stencils And Straight Edges..
Made In Usa!.
Cutting Slats Are 1/8" X 1 1/2" Flat Bar With Progressive Spacing, Tight In The Middle And Wider Toward The Sides. 3 Gallons Of Water Leaves 5 1/2" Of Air Space To Limit Splash Back. The Included Wave Break Also Prevents Splashing When Rolling Around..
Does *Not* Include Sevice Cart Or Plasma Cutter - Requires Harbor Freight #62179 - 30"X 16" Service Cart, Will Potentially Work With Other Brands - Includes - Long Reach Clamp, Plasma Table Ends, Cutting Slats, 4" F.B. Sides, Wave Break, (4) Cord Holders, Drain Plug & New Hardware..
Features
- Weld our kit together, then bolt onto your 30"x16" service cart (NOT included). Seal it up, add water and then you will have the best plasma table roll-around available for hand-held plasma cutting. Actual O.D. of table is 29.25 x 15.125 . We also make this for larger 36x24 carts. Finished working height of both is 35.5".
- Does *NOT* include sevice cart or plasma cutter - Requires Harbor Freight #62179 - 30x 16 service cart, will potentially work with other brands - Includes - long reach clamp, plasma table ends, cutting slats, 4 F.B. sides, wave break, (4) cord holders, drain plug & new hardware.
- Clamp option - 5/8 post for fixture/weld tables. Edge clamp style for our table & standard fab. tables up to 9/16 thick. The clamp is perfect for holding our Plasma Stencils and straight edges.
- Cutting slats are 1/8 x 1 1/2 flat bar with progressive spacing, tight in the middle and wider toward the sides. 3 gallons of water leaves 5 1/2 of air space to limit splash back. The included wave break also prevents splashing when rolling around.
- Made in USA!
- See more on Amazon...
Brand: 911 motorsports | Manufacturer: 911 motorsports
Dimensions: 4.00 x 30.00 x 8.00 inches
See On Amazon #14
PT-60 Drag Shield Conversion - Tecmo brand
Asin: B0CZGDWL8P
These Are The Consumables You Need For Drag Cutting. This Is What You Want To Extend The Consumable Life As The Tip Never Touches The Metal Being Cut..
These Are Quality Oem Tecmo Consumables Made In Italy, Not The Cheap Knockoffs Coming In From Chyna..
Features
- Fits the Everlast Powerplasma 52i, 62i, and Hatchet 60 plasma cutters and possibly others with the PT-60 style torch
- These are quality OEM Tecmo consumables made in Italy, not the cheap knockoffs coming in from Chyna.
- These are the consumables you need for drag cutting. This is what you want to extend the consumable life as the tip never touches the metal being cut.
- See more on Amazon...
Brand: 911 motorsports | Manufacturer: Tecmo
See On Amazon #15
Splash Guard for CNC Plasma Torch - Hyp Pmax 45XP/65/85/105
Asin: B0CJDMQMFD
Easily Slides On And Off For Setup, But Won't Fall Off While Cutting. We Added A Crosshair On The Top For Quick/Rough Reference Of Torch Center..
Made In Usa! - We Are Working On More Torch Applications. Contact Us If Your Torch Isn't Listed..
3D Printed From Flexible Tpu Which Holds Up To The Heat Well, But Will Gradually Melt Away From The Blowback Of Pierce Cuts..
These Are Torch Specific And Are Slightly Shorter Than Your Cutting Tip, So They Won't Interfere While Cutting..
Features
- These Splash Guards are a simple and effective way of containing the water splash created while CNC plasma cutting. They also keep the sparks low and shield the arc.
- These are torch specific and are slightly shorter than your cutting tip, so they won't interfere while cutting.
- Easily slides on and off for setup, but won't fall off while cutting. We added a crosshair on the top for quick/rough reference of torch center.
- 3D printed from flexible TPU which holds up to the heat well, but will gradually melt away from the blowback of pierce cuts.
- Made in USA! - We are working on more torch applications. Contact us if your torch isn't listed.
- See more on Amazon...
Brand: 911 motorsports | Manufacturer: 911 Motorsports
See On Amazon #16
36" x 24" Plasma Cutter - Water Table Conversion Kit - Edge Clamp
Asin: B0C51732PG
Clamp Option - 5/8" Post For Fixture/Weld Tables. Edge Clamp Style For Our Table & Standard Fab. Tables Up To 9/16" Thick. The Clamp Is Perfect For Holding Our Plasma Stencils And Straight Edges..
Made In Usa!.
Cutting Slats Are 1/8" X 1 1/2" Flat Bar. 6 Gallons Of Water Leaves 5 1/2" Of Air Space To Limit Splash Back. The Included Wave Break Also Prevents Splashing When Rolling Around..
*Not* Included: Service Cart Or Plasma Cutter - Requires Harbor Freight #62587 - 36"X 24" Service Cart, Will Potentially Work With Other Brands - Includes: Plasma Table Ends, 4" Flat-Bar Sides, Cutting Slats, Long Reach Clamp, Wave Break, (6) Cord Holders, Drain Plug & New Hardware..
Features
- Weld our kit together, then bolt onto your 36"x24" service cart (NOT included). Seal it up, add water and then you will have the best plasma table roll-around available. Actual O.D. of table is 35.75" x 23.75". We also make this for smaller 30x16 carts. Finished working height of both is 35.5".
- *NOT* included: Service Cart or Plasma Cutter - Requires Harbor Freight #62587 - 36x 24 service cart, will potentially work with other brands - Includes: plasma table ends, 4 flat-bar sides, cutting slats, long reach clamp, wave break, (6) cord holders, drain plug & new hardware.
- Clamp option - 5/8 post for fixture/weld tables. Edge clamp style for our table & standard fab. tables up to 9/16 thick. The clamp is perfect for holding our Plasma Stencils and straight edges.
- Cutting slats are 1/8 x 1 1/2 flat bar. 6 gallons of water leaves 5 1/2 of air space to limit splash back. The included wave break also prevents splashing when rolling around.
- Made in USA!
- See more on Amazon...
Brand: 911 motorsports | Manufacturer: 911 motorsports
Dimensions: 4.00 x 36.00 x 8.00 inches | Weight: 48.00 Pounds
See On Amazon #17
Mercedes G-Wagen Spare Tire Flip Mount - 1990-2018 G Class G500/550/55/63/65 W463 G Wagon
Asin: B0779NDRWR
Comes With Two Sets Of Door Spacers, To Fit Any Wheel That Mercedes Offers.
Powder Coated Satin Black.
This Spare Tire Mount Flips The Wheel Over To Show Off The Good Side Of The Wheel.
Features
- Ditch your bland spare tire cover and make room for larger tires
- This spare tire mount flips the wheel over to show off the good side of the wheel
- Comes with two sets of door spacers, to fit any wheel that Mercedes offers
- Powder coated satin black
- See more on Amazon...
Brand: 911 motorsports | Manufacturer: 911 motorsports
Dimensions: 12.00 x 12.00 x 12.00 Inches
See On Amazon #18
4 Point Jack Adapter for Floor & Transmission Jacks - Lift axle, Transmission, Transfer case, Fuel Tank, Bumper
Asin: B0779Q5RM8
Offers The Versatility To Hold Just About Anything That Is Large, Heavy And Awkward With Your Transmission Or Floor Jack.
Made In Usa--800 Lbs. Capacity At Maximum Extension -- Main/Top Bars Adjust From 17-28” Wide. Threaded Bars Adjust From 6-25” Wide..
Floor Option Includes "Bolt On" Style Pin. Message Us With Note If You Want Another Style. Transmission Option Includes Adapter That Requires 1/2" Hole To Be Drilled Through Center Of Jack..
Features
- New and improved 4 point jack adapter uses our common 1 1/2" adapter pin. Check out our "floor jack extension" that works with this and makes your jack even more versatile.
- Floor option includes bolt on style pin. Message us with note if you want another style. Transmission option includes adapter that requires 1/2 hole to be drilled through center of jack.
- Offers the versatility to hold just about anything that is large, heavy and awkward with your transmission or floor jack
- Made in USA--800 lbs. capacity at maximum extension -- Main/top bars adjust from 17-28 wide. Threaded bars adjust from 6-25 wide.
- See more on Amazon...
Brand: 911 motorsports | Manufacturer: 911 Motorsports
Dimensions: 4.00 x 12.00 x 14.00 inches
See On Amazon #19
MIG Holster - MIG Gun/Torch Holder Stand - 2 pack
Asin: B01K1J47C6
Bell End Holds Your Gun Without Arcing Feed Wire.
Made In Usa.
1" I.D. With 5/8" Thru Hole Fits Large And Small Welders Of Any Brand Or Model.
Flared Out Entry Makes It Easy To Find The Holster.
Features
- Formed for quick draw welding with your MIG gun
- Flared out entry makes it easy to find the holster
- Bell end holds your gun without arcing feed wire
- 1 I.D. with 5/8 thru hole fits large and small welders of any brand or model
- Made in USA
- See more on Amazon...
Brand: 911 motorsports | Manufacturer: 911 motorsports
Dimensions: 1.50 x 2.50 x 2.50 inches
See On Amazon #20
Long Reach Clamp for Plasma & Fixture Table - Edge Clamp
Asin: B0CJ5SKCYZ
Adjustable Arm And Base Is Made In Usa. The Clamp Started Off As A Pittsburgh Clamp, Which We Modified..
The Adjustable Arm Will Clamp 8"-12" From The Center Of Clamp Pivot. Rated Up To 70# Of Clamping Force At Max Extension. Will Hold Objects Up To 5" Tall..
Features
- Includes 1 clamp, choose your style. - 5/8" post for fixture/weld tables. Edge clamp for our Plasma Table & standard fab./work tables from 1/8"-9/16" thick (multiple spacers included).
- The adjustable arm will clamp 8-12 from the center of clamp pivot. Rated up to 70# of clamping force at max extension. Will hold objects up to 5 tall.
- Adjustable arm and base is Made in USA. The clamp started off as a Pittsburgh clamp, which we modified.
- See more on Amazon...
Brand: 911 motorsports | Manufacturer: 911 motorsports
See On Amazon #21
4 Point Jack Adapter for Transmission Jacks - Lift axle, Transmission, Transfer case, Fuel Tank, Bumper
Asin: B0779QDXBJ
Offers The Versatility To Hold Just About Anything That Is Large, Heavy And Awkward With Your Transmission Or Floor Jack.
Made In Usa--800 Lbs. Capacity At Maximum Extension -- Main/Top Bars Adjust From 17-28” Wide. Threaded Bars Adjust From 6-25” Wide..
Floor Option Includes "Bolt On" Style Pin. Message Us With Note If You Want Another Style. Transmission Option Includes Adapter That Requires 1/2" Hole To Be Drilled Through Center Of Jack..
Features
- New and improved 4 point jack adapter uses our common 1 1/2" adapter pin. Check out our "floor jack extension" that works with this and makes your jack even more versatile.
- Floor option includes bolt on style pin. Message us with note if you want another style. Transmission option includes adapter that requires 1/2 hole to be drilled through center of jack.
- Offers the versatility to hold just about anything that is large, heavy and awkward with your transmission or floor jack
- Made in USA--800 lbs. capacity at maximum extension -- Main/top bars adjust from 17-28 wide. Threaded bars adjust from 6-25 wide.
- See more on Amazon...
Brand: 911 motorsports | Manufacturer: 911 Motorsports
Dimensions: 4.00 x 12.00 x 14.00 inches
See On Amazon #22
PT-60 Drag Tip Set - 60A - Tecmo brand
Asin: B0CZPM7276
Fits The Everlast 60S And 62I Plasma Cutters And Possibly Others With The Pt-60 Or Ipt-60 Style Torch And Long Drag Shield Conversion..
These Are Quality Oem Tecmo Consumables Made In Italy, Not The Cheap Knockoffs From Chyna..
Requires Long Drag Shield Conversion Available In Our Store Which Includes #17 And #18 In The Chart..
Features
- Replacement consumables for PT-60 torch with long Drag Shield Conversion. Comes with 3 electrodes and 3 tips; these are #8 and #16 in the chart.
- Requires long Drag Shield Conversion available in our store which includes #17 and #18 in the chart.
- Fits the Everlast 60S and 62i plasma cutters and possibly others with the PT-60 or IPT-60 style torch and long Drag Shield Conversion.
- These are quality OEM Tecmo consumables made in Italy, not the cheap knockoffs from Chyna.
- See more on Amazon...
Brand: 911 motorsports | Manufacturer: Tecmo
See On Amazon #23
PT-80 Drag Shield Conversion - Tecmo brand
Asin: B0CZLXF3PH
These Are The Consumables You Need For Drag Cutting. This Is What You Want To Extend The Consumable Life As The Tip Never Touches The Metal Being Cut..
These Are Quality Oem Tecmo Consumables Made In Italy, Not The Cheap Knockoffs Coming In From Chyna..
Features
- Fits the Everlast 80S and 82i plasma cutters and possibly others with the PT-80 style torch
- These are quality OEM Tecmo consumables made in Italy, not the cheap knockoffs coming in from Chyna.
- These are the consumables you need for drag cutting. This is what you want to extend the consumable life as the tip never touches the metal being cut.
- See more on Amazon...
Brand: 911 motorsports | Manufacturer: Tecmo
See On Amazon #24
PT-80 Drag Tip Set - 80A - Tecmo brand
Asin: B0CZCG4JLH
Fits The Everlast 80S And 82I Plasma Cutters And Possibly Others With The Pt-80 Or Ipt-80 Style Torch And Drag Shield Conversion..
Quality Oem Tecmo Consumables Made In Italy, Not The Cheap Knockoffs From Chyna..
Requires Drag Shield Conversion Available In Our Store Which Includes #11 And #12 In The Chart..
Features
- Replacement consumables for PT-80 torch with Drag Shield Conversion. Comes with 3 electrodes and 3 tips; these are #3 and #9 in the chart.
- Requires Drag Shield Conversion available in our store which includes #11 and #12 in the chart.
- Fits the Everlast 80S and 82i plasma cutters and possibly others with the PT-80 or IPT-80 style torch and Drag Shield Conversion.
- Quality OEM Tecmo consumables made in Italy, not the cheap knockoffs from Chyna.
- See more on Amazon...
Brand: 911 motorsports | Manufacturer: Tecmo
See On Amazon #25
Third Hand Tube Holder - for roll bar/cage - flexible tubing clamp
Asin: B07WVR5QJ9
Uses Strong Hand Pliers That Clamp Up To 2" Tube.
Arms Are Made In The Usa.
Arms Are Bendable, But Strong Enough To Hold Position.
Features
- Holds tubes for welding while still allowing fine adjustment
- Arms are bendable, but strong enough to hold position
- Uses Strong Hand pliers that clamp up to 2 tube
- Arms are Made in the USA
- See more on Amazon...
Brand: 911 motorsports | Manufacturer: 911 Motorsport
Dimensions: 2.00 x 10.00 x 6.00 inches
See On Amazon #26
Pointer for CNC Plasma torch - PT-60/IPT-60
Asin: B0CJCWXZRZ
They Are Torch Specific And Have A Positive Stop To Ensure Alignment..
Made In Usa! - We Are Working On More Torch Applications. Contact Us If Your Torch Isn't Listed..
3D Printed From Flexible Tpu For Ultimate Durability..
It Also Has Holes In The End To Help Air Escape And Assist It With Coming Off, In Case You Accidentally Fire Your Torch With The Pointer On..
Features
- These Pointers are a simple and effective way of lining up your CNC plasma torch. It slides over your torch tip to give a perfect center point for aligning your cuts. We incorporated ribs to easily pull it off.
- It also has holes in the end to help air escape and assist it with coming off, in case you accidentally fire your torch with the pointer on.
- They are torch specific and have a positive stop to ensure alignment.
- 3D printed from flexible TPU for ultimate durability.
- Made in USA! - We are working on more torch applications. Contact us if your torch isn't listed.
- See more on Amazon...
Brand: 911 motorsports | Manufacturer: 911 motorsports
See On Amazon #27
Square - Plasma Cutter Water Table for 15.5 gal. tub - 5/8" Post
Asin: B0C5SH6NB6
Fits Behrens #62/ 15.5 Gal. Square Tub -Not Included- Which Are In Stock At Most Farm & Hardware Stores For Around $35, Or You Can Buy Them Online Here For A Little More. Https://Www.Amazon.Com/Behrens-62-Stainless-Steel-Tub/Dp/B00002n84q.
Made In Usa!.
All Of The Sparks/Slag And Most Of The Smoke Is Captured With 6" Air Gap Above The Water. The Usable Cutting Area Is 20"X19". Cutting Slats Are 1/8" X 1 1/2" Flat Bar. Laser Cut From 1/8" Steel And Requires Welding, About 10 Minutes..
Clamp Option - 5/8" Post For Fixture/Weld Tables. Edge Clamp Style For Our Table & Standard Fab. Tables Up To 9/16" Thick. The Clamp Is Perfect For Holding Our Plasma Stencils And Straight Edges..
Features
- Tub NOT included - Comes with long reach clamp, plasma table frame & cutting slats. This square plasma table will sit on top a common wash tub and includes an adjustable clamp to hold our Plasma Stencils and cutting guides.
- Clamp option - 5/8 post for fixture/weld tables. Edge clamp style for our table & standard fab. tables up to 9/16 thick. The clamp is perfect for holding our Plasma Stencils and straight edges.
- Fits Behrens #62/ 15.5 gal. square tub -NOT included- which are in stock at most farm & hardware stores for around $35, or you can buy them online here for a little more. https://www.amazon.com/Behrens-62-Stainless-Steel-Tub/dp/B00002N84Q
- All of the sparks/slag and most of the smoke is captured with 6 air gap above the water. The usable cutting area is 20x19. Cutting slats are 1/8 x 1 1/2 flat bar. Laser cut from 1/8 steel and requires welding, about 10 minutes.
- Made in USA!
- See more on Amazon...
Brand: 911 motorsports | Manufacturer: 911 motorsports
Dimensions: 4.50 x 20.00 x 4.50 inches | Weight: 18.00 Pounds
See On Amazon