Precision Auto Products - Buying Guide
Last Updated: 05/02/2024
Share on
Bestselling from Precision Auto Products on Amazon
- Razor Twist Grip Throttle - Factory Original Razor 24V 4-Wire Twist Throttle for the Razor E100 / E1...
- Chain for Razor MX500 and MX650 - Heavy Duty - 132 Link Drive Chain - #25 Roller Chain 132L - Razor ...
- Controller for Razor Dirt Quad - 24V Control Module HB2430-TYD6-FS-ROHS for Razor Dirt Quad Version ...
- Starter Solenoid Relay Switch for SeaDoo 3D, GS, GSI, GSX, GTI, GTS, GTX, HX, LRV, RX, RXP, RXT, SP,...
- Disc Brake Caliper Assembly for Razor - Premium Replacement Brake Caliper for Razor MX500, MX650 Dir...
- 36V 1A Battery Charger for Razor - 36V to 42V 1000mA Premium Universal Replacement Battery Charger -...
- 12V Battery Charger for Razor E90-12V 1A Replacement Charger for Razor, PowerRider 360, Jr. Electric...
- 3.00-4 Inner Tube Razor E300 - Premium Heavy Duty 260x85 Replacement Mobility Scooter Tire Tube - Pe...
- Marine Battery Disconnect Switch - Premium On-Off Position Master Cut Off Switch - 6V 12V 24V 48V - ...
- Chain Tensioner Spring for Razor MX500 (2 Pack) - Heavy Duty Replacement Tension Springs for The Raz...
#1
Razor Twist Grip Throttle - Factory Original Razor 24V 4-Wire Twist Throttle for the Razor E100 / E125 (Versions 10+), Razor E200 (V24+), E300 (V20+), Pocket Mod (13+) W13113601043
Asin: B017V5PU4W | Model: W13113601043-1 | PartNumber: W13113601043-1
Check Your Serial Number - In Order To Determine If This Throttle Is A Match For Your Scooter, You Need To Check The Barcode Serial Id On Your Razor Scooter First. The Version Of Your Scooter Is Determined Based On Your 8-Digit Serial Number. The Serial Number Can Be Found Below The Barcode On The Battery Cover And/Or On The Bottom Of The Frame. The Two Digit Number Between The Dashes Is The Version Number (E.G. "01"= Version 1, "02"= Version 2, Etc.).
Plug And Play Easy Installation - 4-Wire Connector And 50" Throttle Cable..
Order Accurately - This Throttle Will Not Work With All Razor Products. Older Versions, Use A Different Throttle (Even Though It Looks Similar). This Part Is Factory Tested And Works As Intended With The Listed Compatible Models..
Version Specific Part - This Throttle Only Works With The Razor E100 Version 10 And Up, E125 Version 10 And Up, Razor E200 Version 24 And Up, Razor E300 Version 20 And Up, Razor Pocket Mod Version 13 And Up.
Features
- Razor Twist Grip Throttle - Factory Original Razor 24V 4-Wire (Male 4-Pin Connector) Twist Throttle for the Razor E100 / E125 (Versions 10+), Razor E200 (V24+), E300 (V20+), Pocket Mod (13+) - Razor Part # W13113601043
- VERSION SPECIFIC PART - This Throttle only works with the Razor E100 Version 10 and up, E125 Version 10 and up, Razor E200 Version 24 and up, Razor E300 Version 20 and up, Razor Pocket Mod Version 13 and up
- CHECK YOUR SERIAL NUMBER - In order to determine if this throttle is a match for your scooter, you need to check the Barcode Serial ID on your Razor Scooter first. The Version of your scooter is determined based on your 8-digit Serial Number. The Serial Number can be found below the Barcode on the battery cover and/or on the bottom of the frame. The two digit number between the dashes is the version number (e.g. 01= version 1, 02= version 2, etc.)
- ORDER ACCURATELY - This throttle will NOT work with all Razor Products. Older versions, use a different throttle (even though it looks similar). This part is factory tested and works as intended with the listed compatible models.
- Plug and Play Easy Installation - 4-WIRE Connector and 50 Throttle Cable.
- See more on Amazon...
Brand: Razor | Manufacturer: Precision Auto Products
Weight: 0.26 Pounds
See On Amazon #2
Chain for Razor MX500 and MX650 - Heavy Duty - 132 Link Drive Chain - #25 Roller Chain 132L - Razor MX500 Electric Drive Chain - MX650 Dirt Bike - Razor SX500 - MiniMoto XRF500 - Master Link Included
Asin: B0719SQDRM | Model: 4333038958 | PartNumber: 4333038958 | Ean: 0721541223160 | UPC: 721541223160
Total Chain Links - 132 Links (66 Inner Links + 66 Outer Links). 1/4" (6.35 Mm) Pitch. 132 Pin.
Heavy Duty And Easy To Install - Master Link Included With Each Premium 132L Drive Chain.
Works With All Versions: Razor Mx500, Mx650 And Sx500 Electric Dirt Bikes.
Quality You Can Count On - Pre-Assembled, Durable, And Long Lasting High Quality #25 Chain With 132 Links, Also Known As A 132 Pin Chain.
Features
- 132 Link Heavy Duty Chain - Razor MX500, MX650, SX500 Dirt Rocket Drive Chain - 132 Link | #25 Chain 132L | Razor MX500 Dirt Rocket | Razor MX650 Drive Chain / MiniMoto XRF500
- Quality You Can Count On - Pre-Assembled, Durable, and long lasting high quality #25 chain with 132 links, also known as a 132 pin chain
- Total Chain Links - 132 links (66 inner links + 66 outer links). 1/4 (6.35 mm) pitch. 132 pin
- Works With All Versions: Razor MX500, MX650 and SX500 Electric Dirt Bikes
- Heavy Duty and Easy to Install - Master link included with each premium 132L drive chain
- See more on Amazon...
Brand: Precision Auto Products | Manufacturer: Precision Auto Products
Dimensions: 3.20 x 0.60 x 6.70 Inches | Weight: 0.28 pounds
See On Amazon #3
Controller for Razor Dirt Quad - 24V Control Module HB2430-TYD6-FS-ROHS for Razor Dirt Quad Version 11 and up, 5 Connectors with 6-Pin Throttle Connector - OEM Part W25143069015
Asin: B08X71HQ7R | Model: W25143069015-1 | PartNumber: W25143069015-1
Razor Factory Original Part - Part Number W25143069015.
Check Your Version - Model Versions Can Be Determined Based On The Product Id Code On Your Razor Product. The Product Id Code Can Be Found On The Battery Cover And/Or On The Bottom Of The Frame. The 7Th And 8Th Numbers In Your Product Id Code Are The Version Number Of Your Razor Product (E.G. "01" = Version 1, "02" = Version 2, Etc.).
Easy Installation And Perfect Fit - This 24 Volt Controller Works With All Razor Dirt Quads V11+..
Controller Model Number - Hb2430-Tyd6-Fs-Rohs.
Features
- Razor Dirt Quad 24V Controller - 5 Wire / Connectors. Compatible with the Razor Dirt Quad Version 11 and Above
- Controller Model Number - HB2430-TYD6-FS-ROHS
- Razor Factory Original Part - Part Number W25143069015
- Easy Installation And Perfect Fit - This 24 Volt Controller works with all Razor Dirt Quads V11+.
- Check Your Version - Model versions can be determined based on the product ID code on your Razor product. The product ID code can be found on the battery cover and/or on the bottom of the frame. The 7th and 8th numbers in your product ID code are the version number of your Razor product (e.g. 01 = Version 1, 02 = Version 2, etc.)
- See more on Amazon...
Brand: Precision Auto Products | Manufacturer: Precision Auto Products
Weight: 0.47 pounds
See On Amazon #4
Starter Solenoid Relay Switch for SeaDoo 3D, GS, GSI, GSX, GTI, GTS, GTX, HX, LRV, RX, RXP, RXT, SP, SPI, SPX, SUV, XP, XP800, Wake, Challenger, Explorer, Islandia, Speedster, Sportster, Utopia 278-0
Asin: B004VA3G9C | Model: 278-001-802 | PartNumber: 278-001-802 | Ean: 7294104364899
Easy Installation - Simple To Install. The Easiest Way To Get The Gasket On The Electric Box Simply Requires You To Put The Gasket Around The Box And Then Push On The Lid.
No More Click Click, When You Turn Your Key - Our Solenoid Relay Replacement Is Computer Tested For Consistent Quality And Unsurpassed Reliability, Meets Factory Specs For Fit And Performance.
Quality You Can Count On - Weather Resistant Quality Marine Starter Solenoid For Seadoos Jetskis, Wave Runners. Used On Ski-Doo, Can-Am, And Sea-Doo Sport-Boat And Pwc.
Universal Fit - Exact Replacement Marine Starter Solenoid Relay Switch For Sea Doo Wake, Challenger, Explorer, Islandia, Speedster, Sportster, Utopia 278-001-802, 278-001-376, 278-000-513.
Features
- Premium Starter Solenoid Relay Switch for SeaDoo 3D, GS, GSI, GSX, GTI, GTS, GTX, HX, LRV, RX, RXP, RXT, SP, SPI, SPX, SUV, XP
- Universal Fit - Exact replacement marine starter solenoid relay switch for Sea Doo Wake, Challenger, Explorer, Islandia, Speedster, Sportster, Utopia 278-001-802, 278-001-376, 278-000-513
- Easy Installation - Simple to Install. The easiest way to get the gasket on the electric box simply requires you to put the gasket around the box and then push on the lid
- Quality You Can Count On - Weather resistant quality marine starter solenoid for SeaDoos jetskis, wave runners. Used on Ski-Doo, Can-Am, and Sea-Doo Sport-Boat and PWC
- No More Click Click, When You Turn Your Key - Our solenoid relay replacement is computer tested for consistent quality and unsurpassed reliability, meets factory specs for fit and performance
- See more on Amazon...
Brand: Precision Auto Products | Manufacturer: Precision Auto Products
Weight: 0.11 pounds
Warranty: One Year Hassle Free Warranty!
See On Amazon #5
Disc Brake Caliper Assembly for Razor - Premium Replacement Brake Caliper for Razor MX500, MX650 Dirt Rocket, McGrath SX500 and Dirt Quad - Front or Rear Wheel with Flame Disc Brake Rotor Calipers
Asin: B007RQP7Q2 | Model: W15128190009 | PartNumber: W15128190009 | Ean: 0722460262438 | UPC: 722460262438
Perfect Fit And Compatible - Razor Mx500, Mcgrath Sx500 And Razor Mx650 Dirt Bikes, Razor Dirt Quad And Razor E500s.
Universal Brake Caliper - Fits Many Gas Scooters, Pocket Bikes, Electric Scooters, Bicycles, Go-Karts, Atv, Dune Buggies, Electric Bikes.
Quality You Can Count On - Heavy Duty Dual Pad Brake Caliper For Currie, Razor, Bladez Electric Scooters.
Easy Installation - Replacing Your Brake Caliper Replacement Is Simple. Simply Remove The Two Existing Screws (Attached To Frame), Remove The Brake Cable Pinch Bolt. Then Attach The New Caliper, Attach Brake Cable Pinch Bolt, And Two Frame Screws.
Features
- Premium Flame Disc Brake Caliper - Factory Original Replacement Disc Brake Caliper Assembly for all Razor Products with a Disc Brake
- Easy Installation - Replacing Your Brake Caliper Replacement Is Simple. Simply Remove The Two Existing Screws (attached To Frame), Remove The Brake Cable Pinch Bolt. Then Attach The New Caliper, Attach Brake Cable Pinch Bolt, And Two Frame Screws
- Perfect Fit and Compatible - Razor MX500, McGrath SX500 and Razor MX650 Dirt Bikes, Razor Dirt Quad and Razor E500S
- Quality You Can Count On - Heavy Duty Dual Pad Brake Caliper for Currie, Razor, Bladez Electric Scooters
- Universal Brake Caliper - Fits Many Gas Scooters, Pocket Bikes, Electric Scooters, Bicycles, Go-Karts, ATV, Dune Buggies, Electric Bikes
- See more on Amazon...
Brand: Precision Auto Products | Manufacturer: Precision Auto Products
Weight: 0.55 pounds
See On Amazon #6
36V 1A Battery Charger for Razor - 36V to 42V 1000mA Premium Universal Replacement Battery Charger - Mini 3-Prong Connector - Ultra Compact 36V Charger
Asin: B0CXNH65GW | Model: RZHT20CHR | PartNumber: RZHT20CHR
Plug N' Play Battery Charger - Our Charger Is Simple To Use, Red Light Is On When Charging - Green Light Is On When Fully Charged - Note: If Your Battery Will Not Take A Charge With Our Charger, You Will Need To Test Your Battery - In This Case, You Will Likely Have To Replace Your Battery Unless Our Charger Was Not Compatible With Your Product.
Efficient Charging - The Charger Is Equipped With Advanced Safety Features Such As Over Voltage Protection Ensuring Safe And Reliable Charing In Our Compact Charger That Will Fit In Your Pocket, And Will Rapidly Charge Your 36V And 42V Battery In Just A Few Hours Making It An Excellent Investment For Long Term Use..
Important Charging Information - Every Charger We Sell Is Factory Tested. If Your Battery Will Not Take A Charge With Our Charger, You Will Need To Test Your Battery - In This Case, You Will Likely Have To Replace Your Battery Unless Our Charger Was Not Compatible With Your Product.
Universal Voltage Compatibility - Input: Ac 100 - 240V 50/60Hz 1.5A - Output: 36V 1A - Maximum Charging Voltage Up To 42V Dc. This 36V Charger Does Not Work With 12V, 24V, Or 36V Sla (Sealed Lead Acid) Batteries.
Universal 36V / 42V Battery Charger - Our Premium Balance Charger Is Compatible With 36V And 42V Two Wheel - 36V / 42V 3-Prong Inline 8Mm Convex Slot Female Connector (0.3 Inch) In Diameter, 6 Foot Cable.
Features
- 36V - 42V 1A Battery Charger for Razor Mini - Compatible with Razor, Two Wheel, HT 2.0 - 36 Volt / 42 Volt 1000mA UL listed inline mini 3-prong battery charger
- Universal 36V / 42V Battery Charger - Our premium balance charger is compatible with 36V and 42V two wheel - 36V / 42V 3-prong inline 8mm convex slot female connector (0.3 inch) in diameter, 6 foot cable
- Plug N' Play Battery Charger - Our charger is simple to use, Red Light is ON when charging - Green Light is ON when fully charged - NOTE: If your battery will not take a charge with our charger, you will need to test your battery - In this case, you will likely have to replace your battery unless our charger was not compatible with your product
- Universal Voltage Compatibility - Input: AC 100 - 240V 50/60Hz 1.5A - Output: 36V 1A - Maximum charging voltage up to 42V DC. This 36V Charger does NOT work with 12V, 24V, or 36V SLA (Sealed Lead Acid) Batteries
- Efficient Charging - The charger is equipped with advanced safety features such as over voltage protection ensuring safe and reliable charing in our compact charger that will fit in your pocket, and will rapidly charge your 36V and 42V battery in just a few hours making it an excellent investment for long term use.
- Important Charging Information - Every charger we sell is factory tested. If your battery will not take a charge with our charger, you will need to test your battery - In this case, you will likely have to replace your battery unless our charger was not compatible with your product
- See more on Amazon...
Brand: Precision Auto Products | Manufacturer: Precision Auto Products
Dimensions: 3.00 x 5.00 x 2.00 Inches
Warranty: 30 Days
See On Amazon #7
12V Battery Charger for Razor E90-12V 1A Replacement Charger for Razor, PowerRider 360, Jr. Electric Wagon, Boreem Tankman, Mambo Liberty 312, Xcooter Tornado XC505GT2, Minimoto Submersible Cruiser
Asin: B086HWXG7L | Ean: 0721541230014 | UPC: 721541230014
Power Input And Output Of Charger - Input Ac100 - 120V 50/60Hz - Output: 12V 1000Ma - 3 Prong Inline Female Connector - Model #Ql-09002-B1201000h.
Very Important Info - 12V Sealed Lead Acid "Sla" Batteries Have On Average A 1 - 2 Year Life Span, Sometimes Longer. Generally Battery Life Will Vary With Use, And Will Need To Be Replaced Within 1-2 Years. If Our Charger Does Not Charge Your Battery, Or The Battery Does Not Hold A Charge, You Will Need To Replace The Battery. If The Green Light On Our 12V Charger Lights Up When You First Plug In The Battery, The Battery Voltage Is Too Low To Take A Charge, And Will Need To Be Replaced..
Safe And Easy Charging - Charging Indicator: Red Light Is On When Charging - Green Light Is On When Fully Charged. Charge Time: 4-6 Hours.
Heavy Duty And Reliable - Our Replacement Charger Is Identical To The Factory Original Battery Charger Part W13111401014 With 3-Prong Inline (Female) Connector End, And Is A Compatible Charger For Many Of Razor’S 12 Volt Electric Products.
Features
- 12V 1A Battery Charger for the Razor E90 - Universal fit and perfect compatibility with the Razor E90 Accelerator, PowerRider 360, Razor Jr. Electric Wagon, Boreem Tankman, Mambo Liberty 312, Xcooter Tornado XC505GT2, Minimoto Submersible Cruiser and other 12V batteries
- Heavy Duty and Reliable - Our replacement charger is identical to the factory original battery charger part W13111401014 with 3-prong inline (female) connector end, and is a compatible charger for many of Razor s 12 volt electric products
- Power Input and Output of Charger - Input AC100 - 120V 50/60Hz - Output: 12V 1000mA - 3 Prong Inline Female Connector - Model #QL-09002-B1201000H
- Safe and Easy Charging - Charging indicator: Red light is ON when charging - Green light is ON when fully charged. Charge time: 4-6 hours
- Very Important Info - 12V Sealed Lead Acid SLA batteries have on average a 1 - 2 year life span, sometimes longer. Generally battery life will vary with use, and will need to be replaced within 1-2 years. If our charger does not charge your battery, or the battery does not hold a charge, you will need to replace the battery. If the GREEN light on our 12V charger lights up when you first plug in the battery, the battery voltage is too low to take a charge, and will need to be replaced.
- See more on Amazon...
Brand: Precision Auto Products | Manufacturer: Precision Auto Products
See On Amazon #8
3.00-4 Inner Tube Razor E300 - Premium Heavy Duty 260x85 Replacement Mobility Scooter Tire Tube - Perfect for Razor E300 Scooter, Pocket Rocket, Utility Dolly, Hand Truck 3.00 x 4 Angle Valve Tube (1)
Asin: B06Y1FJKZF | Ean: 0721541223115 | UPC: 721541223115
Heavy Duty And Thorn Resistant - Our 3.00-4 Tube Is A 10" Diameter 260X85 Tube Is Made Of The Strongest Quality Rubber Which Provides Long Term Reliability For Your Dolly Wheels, Generator, Hand Truck Tires, Utility Cart And Mobility Scooters Pneumatic Wheels..
Easy Installation - Get Back Up And Running In No Time. Please Note: This 3.00X4 Tube Will Not Fit Razor E300 Scooters Version 41+ Rear Wheels. Our 3.00 - 4 Inner Tube Will Fit All Razor E300 Front Wheels..
Universal Fit - Inner Tube For The Razor E300 (V1-40) Electric Scooter (Part # W13113099078) , The Razor Pocket Rocket (All Versions) And The Razor Mini Chopper (Rear Wheel)..
Features
- Premium Quality - Strong & Durable 3.00-4 Replacement OEM Electric Scooter Angle Valve 3.00-4 Inner Tube for Mobility Scooters, Razor Scooters, Currie Scooters, Pride Mobility Scooters, Gas Scooters, Goped, Bladez, Go Karts, Mini ATVs, Hand Trucks and more.
- Universal Fit - Inner tube for the Razor E300 (V1-40) Electric Scooter (Part # W13113099078) , the Razor Pocket Rocket (All Versions) and the Razor Mini Chopper (Rear Wheel).
- Heavy Duty and Thorn Resistant - Our 3.00-4 Tube is a 10 Diameter 260x85 Tube is made of the strongest quality rubber which provides long term reliability for your Dolly Wheels, Generator, Hand Truck Tires, Utility Cart and Mobility Scooters Pneumatic Wheels.
- Easy Installation - Get back up and running in no time. Please Note: This 3.00x4 tube will not fit Razor E300 Scooters Version 41+ rear wheels. Our 3.00 - 4 inner tube will fit All Razor E300 front wheels.
- See more on Amazon...
Brand: Precision Auto Products | Manufacturer: Precision Auto Products
Dimensions: 3.00 x 5.00 x 1.00 inches | Weight: 0.31 Pounds
See On Amazon #9
Marine Battery Disconnect Switch - Premium On-Off Position Master Cut Off Switch - 6V 12V 24V 48V - Battery for Boat, ATV, RV, UTV, Heavy Duty Waterproof Isolator Switch, 275/1250 Amps (On-Off)
Asin: B07WTRNQKW | Model: PA-MSTR-SW | PartNumber: PA-MSTR-SW | Ean: 0721541229933 | UPC: 721541229933
Universal Compatibility - Simple Installation - Used For Dc 6 - 48V Systems To Isolate And Secure The Electrical System, Can Stand Alone Or Be Connected Together With Other Switches. Our Battery Cut Off Kill Switch Has Four Removable Side Plates Which Provide Easy Access.
Safe And Efficient - Tin-Plated Copper Studs And Nuts - Ignition-Protected, Simple To Install, Universally Used For Cars, Battery Powered Vehicles, Rv And Boat, Also Used For Electrical Equipment's Switch.
Heavy Duty And Extremely Reliable - Eliminate Any Power Draw From The Battery When Your Vehicle Or Boat Is Not In Use, Disconnects The Battery Safely. The Rear Cover Insulates The Rear Terminals Against Any Short Circuits, Ensuring That The Switch Meets Abyc Requirements.
Easy To Use - Master On/Off Boat Battery Cut Off Switch. Operation: Voltage: 6V 12V 24V 48V Dc - 275A Dc Continuous Power (1Hr) - 455A Dc Intermittent Power (5 Min) - 1250A Dc Cranking Power (10 Sec) - Stud Size: 2 X 3/8" (10Mm) - Switch On = Power - Switch Off = No Power.
Features
- Premium Marine Battery Disconnect Switch - On Off position switch. Made from durable ABS plastic - Our cut-off battery switch is simple and safe to use
- Easy To Use - Master On/Off Boat Battery Cut Off Switch. Operation: Voltage: 6V 12V 24V 48V DC - 275A DC Continuous Power (1hr) - 455A DC Intermittent Power (5 min) - 1250A DC Cranking Power (10 sec) - Stud Size: 2 x 3/8 (10mm) - Switch ON = Power - Switch OFF = No Power
- Universal Compatibility - Simple Installation - Used for DC 6 - 48V systems to isolate and secure the electrical system, can stand alone or be connected together with other switches. Our battery cut off kill switch has four removable side plates which provide easy access
- Heavy Duty and Extremely Reliable - Eliminate any power draw from the battery when your Vehicle or Boat is not in use, disconnects the battery safely. The rear cover insulates the rear terminals against any short circuits, ensuring that the switch meets ABYC requirements
- Safe and Efficient - Tin-Plated copper studs and nuts - Ignition-Protected, simple to install, universally used for Cars, battery powered Vehicles, RV and Boat, also used for electrical equipment's switch
- See more on Amazon...
Brand: Precision Auto Products | Manufacturer: Precision Auto Products
Weight: 0.10 pounds
See On Amazon #10
Chain Tensioner Spring for Razor MX500 (2 Pack) - Heavy Duty Replacement Tension Springs for The Razor MX500, MX650 & SX500 Dirt Rocket
Asin: B08BF929MX | Ean: 0721541230113 | UPC: 721541230113
Easy Installation - Proper Tension Is Critical For Ensuring Smooth Operation And Extending The Lifespan Of Your Bike's Chain, And These Tensioner Springs Help You Maintain The Right Settings Along With With Simple Installation..
Two Tensioner Springs Inlcuded (2) - Whether You're Performing Routine Maintenance Or Making Repairs, These Mx500 Mx650 Sx500 Chain Tensioner Springs Are A Smart Investment To Ensure Your Razor Dirt Bike Is Running At Its Best..
Quality You Can Count On - Made From High-Quality Materials, These Springs Are Designed To Be Strong And Durable, Resisting Wear And Tear Over Time..
All You Need Is The Spring - These Replacement Springs Are Designed Specifically For Use With The Razor Mx650, Mx500 And Mcgrath Sx500 Electric Dirt Bike, Ensuring Reliable Performance And A Perfect Fit..
Features
- Premium Chain Tensioner Springs - Our springs come in a convenient 2-pack, providing a cost-effective solution for replacing worn or damaged springs ont eh Razor MX500, SX500 and MX650 Dirt Rocket..
- All You Need Is The Spring - These replacement springs are designed specifically for use with the Razor MX650, MX500 and McGrath SX500 electric dirt bike, ensuring reliable performance and a perfect fit.
- Easy Installation - Proper tension is critical for ensuring smooth operation and extending the lifespan of your bike's chain, and these tensioner springs help you maintain the right settings along with with simple installation.
- Quality You Can Count On - Made from high-quality materials, these springs are designed to be strong and durable, resisting wear and tear over time.
- Two Tensioner Springs Inlcuded (2) - Whether you're performing routine maintenance or making repairs, these MX500 MX650 SX500 chain tensioner springs are a smart investment to ensure your Razor Dirt Bike is running at its best.
- See more on Amazon...
Brand: Precision Auto Products | Manufacturer: Precision Auto Products
See On Amazon