SparkFun - Buying Guide
Last Updated: 05/08/2024
Share on
As an Amazon Associate we earn a fee from qualifying purchases when you follow a link to Amazon from this page. We rank the products, but the links to Amazon are promotional. #1
Arduino Pro Mini 328 - 3.3V/8MHz
Asin: B004G53J6M | Model: 8541585392 | PartNumber: 8541585392 | Ean: 0845156592203, 0757901941603 | UPC: 757901941603, 845156592203
3.3V Regulator.
Over Current Protected.
Max 150Ma Output.
Usb Connection Off Board.
Features
- ATmega328 running at 8MHz with external resonator
- USB connection off board
- 3.3V regulator
- Max 150mA output
- Over current protected
- See more on Amazon...
Brand: SparkFun | Manufacturer: Sparkfun Electronics
Weight: 0.04 pounds
See On Amazon #2
SparkFun Serial Basic Breakout - CH340C and USB-C Development Tool Save space and money in your DIY electronics projects
Asin: B07MLXS877 | Model: DEV-15096 | PartNumber: DEV-15096 | Ean: 0602318761811 | UPC: 602318761811
Should Auto Install On Most Operating Systems Without The Need For Additional Drivers.
By Default, The Board Outputs 3.3V And Has 3.3V Signals. Changing This Jumper To 5V Will Cause The Board To Output 5V On The Vcc Pin With 5V Signals..
Pinout: Dtr, Rx, Tx, Vcc, Cts, Gnd.
Works With 5V And 3.3V Systems.
Features
- CH340G USB IC from WCH
- Works with 5V and 3.3V systems
- Should auto install on most operating systems without the need for additional drivers
- Pinout: DTR, RX, TX, VCC, CTS, GND
- By default, the board outputs 3.3V and has 3.3V signals. Changing this jumper to 5V will cause the board to output 5V on the VCC pin with 5V signals.
- See more on Amazon...
Brand: SparkFun | Manufacturer: SparkFun Electronics
Dimensions: 0.28 x 3.54 x 1.97 inches | Weight: 0.02 pounds
See On Amazon #3
SparkFun Electronics Panel Mount USB Micro-B Extension Cable - 6"
Asin: B087Z6ZWHL | Ean: 0619011957021 | UPC: 619011957021
Skill Level: Assembled And Tested.
2X M3 Screw - 14Mm.
Features
- 1x Panel Mount Micro-B USB Extension Cable
- 2x M3 Screw - 14mm
- Skill Level: Assembled and Tested
- See more on Amazon...
Brand: SparkFun | Manufacturer: Electronics123.com, Inc.
See On Amazon #4
SparkFun Qwiic Cable Kit Hook Up I2C Qwiic Development Boards in no time No Soldering Required Includes 10 Different Lengths Styles Breadboardable Polarized 4-pin JST Connector Daisy Chain-able
Asin: B07RB2LRH5 | Model: 15081 | PartNumber: 15081 | Ean: 0845156009541 | UPC: 845156009541
Includes: 3X Qwiic Cable - 50Mm, 3X Qwiic Cable - 100Mm, 1X Qwiic Cable - 200Mm, 1X Qwiic Cable - 500Mm..
Uses 4-Pin Jst Connectors To Quickly Interface Development Boards With Sensors, Lcds, Relays And More..
Also: 1X Qwiic Cable - Breadboard Jumper (4-Pin) And 1X Qwiic Cable - Female Jumper (4-Pin)..
Each Qwiic Cable's Wires Have Been Color Coded To Red, Black, Blue And Yellow With 1Mm Jst Termination..
Features
- Includes 10 cables of various lengths and styles that will get your Qwiic boards connected together.
- Each Qwiic Cable's wires have been color coded to red, black, blue and yellow with 1mm JST termination.
- Includes: 3x Qwiic Cable - 50mm, 3x Qwiic Cable - 100mm, 1x Qwiic Cable - 200mm, 1x Qwiic Cable - 500mm.
- Also: 1x Qwiic Cable - Breadboard Jumper (4-pin) and 1x Qwiic Cable - Female Jumper (4-pin).
- Uses 4-pin JST connectors to quickly interface development boards with sensors, LCDs, relays and more.
- See more on Amazon...
Brand: SparkFun | Manufacturer: SparkFun Electronics
See On Amazon #5
SparkFun Pro Mini ATmega328-5V/16MHz Development Board Compatible with Arduino Boards and IDE
Asin: B004G53J5I | Model: Pro Mini 5V/16MHz | PartNumber: Pro Mini 5V/16MHz | Ean: 0845156592180 | UPC: 845156592180
Supports Auto-Reset.
Max 150Ma Output.
5V Regulator.
No Usb Connection Off Board. Need Ftdi Board (Or Similar Device) To Program..
Features
- ATmega328 running at 16MHz with external resonator (0.5% tolerance)
- No USB connection off board. Need FTDI board (or similar device) to program.
- Supports auto-reset
- 5V regulator
- Max 150mA output
- See more on Amazon...
Brand: SparkFun | Manufacturer: SparkFun Electronics
Dimensions: 0.03 x 1.30 x 0.71 inches
See On Amazon #6
SparkFun Qwiic Pro Micro - USB-C (ATmega32U4) - Compatible with Arduino development board 5V/16MHz microcontroller AP2112 3.3V Voltage Regulator Castellated PTH pin pads Reset button Maximum 6V input
Asin: B084KPT7MH | Model: DEV-15795 | PartNumber: DEV-15795
On-Board Usb-C Connector For Programming. Ap2112 3.3V Voltage Regulator. Pth Pads W/ Castellated Edges.
The Atmega32u4 Can Have The Bootloader Overwritten If Not Used Properly. There Is A Way To Fix The Bootloader If Needed And Instructions Are Available Online. Usb Drivers May Be Needed To Be Installed On A Computer To Communicate With The Board..
Hardware Serial Connections. Includes Uart (I.E. Rx And Tx), Qwiic Connector For I2c, And Spi. Has Onboard Reset Button. Input Maximum Of 6V. Dimensions: 1.3In X 0.7In..
Improved Version Of The Sparkfun Pro Micro. Atmega32u4 Running At 5V/16Mhz Supported Under Arduino Ide V1.0.1+.
Features
- Small Compatible with Arduino board. Includes Reset button, 9x 10-bit ADC pins. 12x Digital I/Os (5 are PWM capable). Note: Board only. Additional accessories will be required.
- Improved version of the SparkFun Pro Micro. ATmega32U4 running at 5V/16MHz Supported under Arduino IDE v1.0.1+
- On-Board USB-C connector for programming. AP2112 3.3V Voltage Regulator. PTH Pads w/ Castellated Edges
- Hardware Serial Connections. Includes UART (i.e. Rx and Tx), Qwiic Connector for I2C, and SPI. Has onboard Reset Button. Input maximum of 6V. Dimensions: 1.3in x 0.7in.
- The AtMega32U4 can have the bootloader overwritten if not used properly. There is a way to fix the bootloader if needed and instructions are available online. USB drivers may be needed to be installed on a computer to communicate with the board.
- See more on Amazon...
Brand: SparkFun | Manufacturer: SparkFun Electronics
Dimensions: 0.59 x 1.30 x 0.70 inches
See On Amazon #7
SparkFun GPS-RTK-SMA Breakout-ZED-F9P (Qwiic)-Concurrent reception of GPS GLONASS Galileo BeiDou High precision GPS 10mm 3 dimensional accuracy Receives L1C/A & L2C bands Voltage:5V or 3.3V Logic:3.3V
Asin: B087T7BV6K | Ean: 0845156010493 | UPC: 845156010493
This Product Is Compatible With U-Blox Pointperfect & Includes A Redemption Code For 1-Month Of Unlimted Access For A Single Device. Take Your Precision To The Next Level With The Pointperfect Gnss Augmentation Service. As Of January 2023, A Promotional Card With A 16 Digit Referral Code Is Included With Your Sparkfun Packaging..
Horizontal Position Accuracy: 2.5M Without Rtk. 0.010M With Rtk. Max Altitude: 50Km (31 Miles). Max Velocity: 500M/S (1118Mph).
Max Navigation Rate: Pvt (Basic Location Over Ubx Binary Protocol) - 25Hz. Rtk - 20Hz. Raw - 25Hz.
Voltage: 5V Or 3.3V But All Logic Is 3.3V. Current: 68Ma - 130Ma (Varies With Constellations And Tracking State). Weight: 6.8G. Dimensions: 43.5Mm X 43.2Mm (1.71In X 1.7In). 2X Qwiic Connectors.
Features
- Concurrent reception of GPS, GLONASS, Galileo and BeiDou. Receives both L1C/A and L2C bands, Time to First Fix: 25s (cold), 2s (hot)
- Voltage: 5V or 3.3V but all logic is 3.3V. Current: 68mA - 130mA (varies with constellations and tracking state). Weight: 6.8g. Dimensions: 43.5mm x 43.2mm (1.71in x 1.7in). 2x Qwiic Connectors
- This product is compatible with u-blox PointPerfect & includes a redemption code for 1-month of unlimted access for a single device. Take your precision to the next level with the PointPerfect GNSS augmentation service. As of January 2023, a promotional card with a 16 digit referral code is included with your SparkFun packaging.
- Max Navigation Rate: PVT (basic location over UBX binary protocol) - 25Hz. RTK - 20Hz. Raw - 25Hz
- Horizontal Position Accuracy: 2.5m without RTK. 0.010m with RTK. Max Altitude: 50km (31 miles). Max Velocity: 500m/s (1118mph)
- See more on Amazon...
Brand: SparkFun | Manufacturer: SparkFun Electronics
Dimensions: 0.51 x 1.77 x 1.77 inches
See On Amazon #8
SparkFun Xbee 3 Module - RP-SMA Antenna Connector
Asin: B08YFL8TM5 | Ean: 0768253933468 | UPC: 768253933468
Built In Microcontroller To Configure And Program The Modules Using Micropython As Well As Digi's Xctu Software.
Hcs08 Cpu Running At Up To 50.33Mhz, 15X Digital I/O Pins, And 4X 10-Bit Adc Pins.
200Ft Indoor Range, Or 4000Ft Outdoor/Line-Of-Sight Range.
Features
- XBee 3 not only handles 802.15.4, and ZigBee, but also BLE protocols and you can now talk to the modules over UART or SPI as well
- 200ft indoor range, or 4000ft outdoor/line-of-sight range
- Built in microcontroller to configure and program the modules using MicroPython as well as Digi's XCTU software
- HCS08 CPU running at up to 50.33MHz, 15x digital I/O pins, and 4x 10-bit ADC pins
- See more on Amazon...
Brand: SparkFun | Manufacturer: Sparkfun
See On Amazon #9
SparkFun AST-CAN485 Development Board Allow out-of-the-box interfacing CAN or RS485 network Compatible with Arduino IDE Industrial device interfacing Small foot-print 7-12DCV input Onboard Power
Asin: B07BHP6MFT | Model: DEV-14483 | PartNumber: DEV-14483 | Ean: 0845156008704 | UPC: 845156008704
Hardware Can Controller/Transceiver. Uses The At90can Microcontroller. Rs485 Transceiver..
Compatible With Arduino Ide Platform. The Can485 Dev Board Bridges The Gap Between The Maker And Industrial Spaces!.
Input Voltage: 7-12V Dc(150 Ma Current Max). 2 Uarts. 8 Analog Inputs. 16 Digital I/Os. 16Mhz Clock..
Pro Mini Pin Compatible. Atmel At90can128 Microcontroller @ 16Mhz, 128Kb Flash 4Kb Sram..
Features
- A miniature compatible with Arduino board in the form factor of the Pro Mini. It possesses an onboard CAN and RS485 ports.
- Pro Mini pin compatible. Atmel AT90CAN128 microcontroller @ 16MHz, 128KB Flash 4KB SRAM.
- Hardware CAN controller/transceiver. Uses the AT90CAN microcontroller. RS485 Transceiver.
- Input voltage: 7-12V DC(150 mA Current Max). 2 UARTs. 8 analog inputs. 16 digital I/Os. 16Mhz clock.
- Compatible with Arduino IDE Platform. The CAN485 Dev Board bridges the gap between the maker and industrial spaces!
- See more on Amazon...
Brand: SparkFun | Manufacturer: SparkFun Electronics
Dimensions: 1.00 x 2.00 x 2.00 inches | Weight: 0.01 Pounds
See On Amazon #10
SparkFun Qwiic Pocket Development Board - ESP32-C6 Mini-1 Module, Including a USB-C Connector, Qwiic Connector, 2-pin JST Battery Connector, Board Dimensions: (Inches) 1" x 1"
Asin: B0CL6GGT7Q | Model: DEV-22925 | PartNumber: DEV-22925 | Ean: 0845156013692 | UPC: 845156013692
Features: Up To 7 12-Bit Adc Channels, Up To 2 Uart Channels (With Flow Control) Usb Serial, One Low Power Uart Channel, One I2c Channel, One Low Power I2c Channel, Led Pwm, One I2s Channel, 4 Mb Flash..
Though Some Are Tied To Specific Pins, Many Of These Peripherals Can Be Mapped To Any Gpio Pin. Due To The Board's Size, It Only Breaks Out Eight Total Gpio Pins, Including Four Adc-Compatible Pins, Low Power And Standard Uart, And An Extra Two Gpio Pins. All Qwiic-Enabled Boards Use A Common 1Mm Pitch, 4-Pin Jst Connector. This Reduces The Amount Of Required Pcb Space, And Polarized Connections Mean You Can’T Hook It Up Wrong..
Also Features: Pcb Antenna, Matter-Compatible, Qwiic Form-Factor, Dimensions: 1" X 1", Four Mounting Holes, 8 Pth Pins, Usb-C Connector, 2-Pin Jst Connector For Lipo Battery (Not Included) 4-Pin Qwiic Connector..
It Features The Esp32-C6 Mini-1 Module. We Designed This Board With Components On Both Sides Of The Pcb To Squeeze As Many Features As Possible Into Its Tiny Footprint, Including A Usb-C Connector, Qwiic Connector, 2-Pin Jst Battery Connector With An On-Board Charging Circuit, As Well As Two Buttons For Reset And Boot. The Design Also Works To Optimize Power Consumption..
Features
- The SparkFun ESP32-C6 Pocket Dev Board is built around a RISC-V single-core processor with 4 MB flash memory in a 1"x1" Qwiic Standard Footprint!
- It features the ESP32-C6 Mini-1 module. We designed this board with components on both sides of the PCB to squeeze as many features as possible into its tiny footprint, including a USB-C connector, Qwiic connector, 2-pin JST battery connector with an on-board charging circuit, as well as two buttons for Reset and Boot. The design also works to optimize power consumption.
- Features: Up to 7 12-bit ADC Channels, Up to 2 UART Channels (with flow control) USB Serial, One Low Power UART Channel, One I2C Channel, One Low Power I2C Channel, LED PWM, One I2S Channel, 4 MB Flash.
- Also features: PCB Antenna, Matter-compatible, Qwiic Form-Factor, Dimensions: 1 x 1, Four Mounting Holes, 8 PTH pins, USB-C Connector, 2-pin JST Connector for LiPo Battery (not included) 4-pin Qwiic Connector.
- Though some are tied to specific pins, many of these peripherals can be mapped to any GPIO pin. Due to the board's size, it only breaks out eight total GPIO pins, including four ADC-compatible pins, Low Power and Standard UART, and an extra two GPIO pins. All Qwiic-enabled boards use a common 1mm pitch, 4-pin JST connector. This reduces the amount of required PCB space, and polarized connections mean you can t hook it up wrong.
- See more on Amazon...
Brand: SparkFun | Manufacturer: SparkFun Electronics
Dimensions: 0.50 x 1.00 x 1.00 inches
See On Amazon #11
SparkFun GPS-RTK-SMA Kit - Includes GPS breakout- Magnetic Mount Antenna- Ground Plate & USB-C Cable - u-Blox ZED-F9P & RTK- High precision accuracy in milimeters- Both Rover & Base station operations
Asin: B0B9TTSN2V | Ean: 0845156012596 | UPC: 845156012596
Gps-Rtk Sma Kit Includes: 1X Sparkfun Gps-Rtk-Sma Breakout - Zed-F9p (Qwiic) 1X Gnss Multi-Band Magnetic Mount Antenna - 5M (Sma) 1X Gps Antenna Ground Plate. 1X Reversible Usb A To C Cable - 0.8M. Note: Tripod Not Included..
Also Included In This Kit Is The Gnss Multiband Antenna, Ground Plate, And A Reversible Usb-A To C Cable. The Included Antenna Features A Magnetic Base And Is Designed To Receive Both The Classic L1 And L2 Gps Bands. Meanwhile, The Ground Plate Will Significantly Increase The Performance Of The Included Antenna!.
Zed-F9p Board Dimensions: 43.5Mm X 43.2Mm (1.71In X 1.7In) Supply Voltage: 3.3V Or 5V Logic..
The Zed-F9p Is A Top-Of-The-Line Module For High Accuracy Gnss And Gps Location Solutions Including Rtk That Is Capable Of 10Mm, Three-Dimensional Accuracy. The Zed-F9p Is Unique In That It Is Capable Of Both Rover And Base Station Operations..
Features
- The SparkFun GPS-RTK-SMA Kit comes with just what you need to get started using GPS Real Time Kinematics and the u-blox ZED-F9P.
- The ZED-F9P is a top-of-the-line module for high accuracy GNSS and GPS location solutions including RTK that is capable of 10mm, three-dimensional accuracy. The ZED-F9P is unique in that it is capable of both rover and base station operations.
- GPS-RTK SMA Kit Includes: 1x SparkFun GPS-RTK-SMA Breakout - ZED-F9P (Qwiic) 1x GNSS Multi-Band Magnetic Mount Antenna - 5m (SMA) 1x GPS Antenna Ground Plate. 1x Reversible USB A to C Cable - 0.8m. Note: Tripod not included.
- ZED-F9P Board Dimensions: 43.5mm x 43.2mm (1.71in x 1.7in) Supply Voltage: 3.3V or 5V Logic.
- Also included in this kit is the GNSS multiband antenna, ground plate, and a reversible USB-A to C cable. The included antenna features a magnetic base and is designed to receive both the classic L1 and L2 GPS bands. Meanwhile, the ground plate will significantly increase the performance of the included antenna!
- See more on Amazon...
Brand: SparkFun | Manufacturer: SparkFun Electronics
Dimensions: 1.97 x 7.05 x 5.20 inches | Weight: 0.02 pounds
See On Amazon #12
SparkFun Pro Micro - RP2040 - Dual Cortex M0+ Processors - 30 programmable IO for Extended Peripheral Support - Timer with 4 Alarms - MicroPython - C/C++ - USB-C Connector for Programming
Asin: B09KDS6CGN | Ean: 0845156011728 | UPC: 845156011728
Sparkfun Pro Micro - Rp2040 Features: Raspberry Pi Foundation's Rp2040 Microcontroller; Ap2112 3.3V Voltage Regulator; Support Programming Languages: Micropython, C/C++; On-Board Usb-C Connector For Programming: Usb 1.1 Host/Device Functionality.
Also Features: Buttons: Boot, Reset; Leds: Power, Ws2812 Addressable Led; 16Mb External Flash Memory; Dimensions: 1.3In X 0.7In. [1] Note: The Gpio Pins Are Muxed So You Can Reconfigure The Pins For The Digital Interface Of Your Choice! Check Out The Rp2040 Datasheet For More Information On The Pins That Are Broken Out On The Board. Note: Board Only..
Also Features: Built-In Resettable Ptc Fuse, Pth Pads W/ Castellated Edges; 20X Multifunctional Gpio Pins [1]: 4X 12-Bit Adc Channels With Internal Temperature Sensor, 0.5 Msa/S, 12-Bit; 10X Pwm Channels; Serial Peripherals; 2X Uarts; 1X I2c (Qwiic Enabled); 1X Spi.
Also Features: Swd Interface; Timer With 4 Alarms; Real Time Counter (Rtc); Usb 1.1 Host/Device Functionality; Supported Programming Languages: Micropython, C/C++.
Features
- RP2040 General Features: Dual Cortex M0+ processors, up to 133 MHz; 264 kB of embedded SRAM in 6 banks; 6 dedicated IO for QSPI flash, supporting execute in place (XIP); 30 programmable IO for extended peripheral support
- Also Features: SWD interface; Timer with 4 alarms; Real time counter (RTC); USB 1.1 Host/Device functionality; Supported programming languages: MicroPython, C/C++
- SparkFun Pro Micro - RP2040 Features: Raspberry Pi Foundation's RP2040 microcontroller; AP2112 3.3V voltage regulator; Support programming languages: MicroPython, C/C++; On-board USB-C connector for programming: USB 1.1 Host/Device functionality
- Also Features: Built-in Resettable PTC Fuse, PTH pads w/ castellated edges; 20x multifunctional GPIO Pins [1]: 4x 12-bit ADC channels with internal temperature sensor, 0.5 MSa/s, 12-bit; 10x PWM channels; Serial Peripherals; 2x UARTs; 1x I2C (Qwiic enabled); 1x SPI
- Also Features: Buttons: Boot, Reset; LEDs: Power, WS2812 Addressable LED; 16MB External Flash Memory; Dimensions: 1.3in x 0.7in. [1] Note: The GPIO pins are muxed so you can reconfigure the pins for the digital interface of your choice! Check out the RP2040 datasheet for more information on the pins that are broken out on the board. Note: Board only.
- See more on Amazon...
Brand: SparkFun | Manufacturer: SparkFun Electronics
Dimensions: 0.20 x 1.38 x 0.71 inches
See On Amazon #13
SparkFun (PID 12942) Bus Pirate - v3.6a with Cable
Asin: B01KKYN9LW | Model: 235 | PartNumber: 235 | Ean: 0717520029595 | UPC: 717520029595
On-Board Multi-Voltage Pull-Up Resistors On-Board 3.3Volt And 5Volt Power Supplies With Software Reset.
A Bootloader For Easy Firmware Updates.
Bus Traffic Sniffers (Spi, I2c).
1Hz - 40Mhz Frequency Measurement 1Khz - 4Mhz Pulse-Width Modulator, Frequency Generator.
Features
- 5.5V tolerant pins. 6V measurement probe
- 1Hz - 40MHz frequency measurement 1kHz - 4MHz pulse-width modulator, frequency generator
- On-board multi-voltage pull-up resistors On-board 3.3volt and 5volt power supplies with software reset
- Bus traffic sniffers (SPI, I2C)
- A bootloader for easy firmware updates
- See more on Amazon...
Brand: SparkFun | Manufacturer: SparkFun
Dimensions: 1.00 x 2.00 x 2.00 inches
See On Amazon #14
SparkFun (PID 14544 Current Sensor Breakout - ACS723 (Low Current)
Asin: B07GL2TT84 | Model: 2690 | PartNumber: 2690 | Ean: 0845156008926 | UPC: 845156008926
Measure Both Ac And Dc Currents From 10Ma Up To 5A.
Capable Of 80Khz Bandwidth. Fixed To 20Khz On Board. Jp1 Can Be Closed To Enable All 80Khz.
Gain 2X To 22X.
Hall Effect.
Features
- ACS723 AC DC current sensor with OPA344 OpAmp
- Hall Effect
- Measure both AC and DC currents from 10mA up to 5A
- Gain 2X to 22X
- Capable of 80KHz bandwidth. Fixed to 20KHz on board. JP1 can be closed to enable all 80KHz
- See more on Amazon...
Brand: SparkFun | Manufacturer: SparkFun
Dimensions: 1.00 x 2.00 x 2.00 inches | Weight: 0.02 pounds
See On Amazon #15
SparkFun Thing Plus ESP32 WROOM
Asin: B083RGHB7P | Model: SEN-15177 | PartNumber: SEN-15177 | Ean: 0845156010110 | UPC: 845156010110
Integrated 802.11 Bgn Wifi Transceiver Integrated Dual-Mode Bluetooth (Classic And Ble).
2.3 To 3.6V Operating Range. 2.5 Μa Deep Sleep Current.
21 Gpio 8-Electrode Capacitive Touch Support Hardware Accelerated Encryption (Aes, Sha2, Ecc, Rsa-4096).
16Mb Of Flash Storage 520Kb Internal Sram.
Features
- Xtensa dual-core 32-bit LX6 microprocessor Up to 240MHz clock frequency
- 16MB of flash storage 520kB internal SRAM
- Integrated 802.11 BGN WiFi transceiver Integrated dual-mode Bluetooth (classic and BLE)
- 21 GPIO 8-electrode capacitive touch support Hardware accelerated encryption (AES, SHA2, ECC, RSA-4096)
- 2.3 to 3.6V operating range. 2.5 A deep sleep current
- See more on Amazon...
Brand: SparkFun | Manufacturer: Sparkfun
Dimensions: 1.00 x 2.00 x 1.00 inches | Weight: 0.02 Pounds
See On Amazon #16
SparkFun Transceiver Breakout - RS-485 SP3485 Half-Duplex Transceiver Operates from a Single +3.3V Supply, Interoperable with +5.0V Logic
Asin: B082MM58RF | Model: BOB-10124 | PartNumber: BOB-10124 | Ean: 0845156004508 | UPC: 845156004508
Also Features: Rs-485 Input/Output Broken Out To Rj-45 Connector, 3.5Mm Screw Terminal, And 0.1" Pitch Header. Driver/Receiver Enable Connected To Rts Line. -7V To +12V Common-Mode Input Voltage Range. Allows Up To 32 Transceivers On The Serial Bus. Driver Output Short-Circuit Protection. 0.9X1.0"..
This Breakout Board Includes The Sp3485 Rs-485 Transceiver, Filter Capacitor, And Other Components Shown On The Schematic. We've Broken Out The Rs-485 Output To Three Different Connections: (1) An Rj-45 Connector, (2) A 3-Pin 3.55Mm Screw Terminal, And (3) A 3-Pin 0.1" Pitch Header; None Of These Output Connectors Come Populated..
The Sp3485 Is A Half-Duplex Transceiver, So It Can Only Communicate One Way At A Time, But It Can Reach Transmission Speeds Of Up To 10Mbps. This Board Requires A Very Low Amount Of Power And Can Operate From A Single +3.3Vdc Supply..
This Breakout Features: Fully Equipped With Sp3485 Rs-485 Transceiver And Supporting Components. Operates From A Single +3.3V Supply. Interoperable With +5.0V Logic..
Features
- This is a breakout board for the SP3485 RS-485 transceiver IC, which will convert a UART serial stream to RS-485.
- This Breakout Features: Fully equipped with SP3485 RS-485 transceiver and supporting components. Operates from a single +3.3V supply. Interoperable with +5.0V logic.
- Also Features: RS-485 input/output broken out to RJ-45 connector, 3.5mm screw terminal, and 0.1 pitch header. Driver/Receiver Enable connected to RTS line. -7V to +12V Common-Mode Input Voltage Range. Allows up to 32 transceivers on the serial bus. Driver Output Short-Circuit Protection. 0.9x1.0.
- The SP3485 is a half-duplex transceiver, so it can only communicate one way at a time, but it can reach transmission speeds of up to 10Mbps. This board requires a very low amount of power and can operate from a single +3.3VDC supply.
- This breakout board includes the SP3485 RS-485 transceiver, filter capacitor, and other components shown on the schematic. We've broken out the RS-485 output to three different connections: (1) an RJ-45 connector, (2) a 3-pin 3.55mm screw terminal, and (3) a 3-pin 0.1 pitch header; none of these output connectors come populated.
- See more on Amazon...
Brand: SparkFun | Manufacturer: SparkFun Electronics
Dimensions: 0.16 x 1.34 x 2.13 inches | Weight: 0.10 pounds
See On Amazon #17
SparkFun RedBoard Qwiic ATMega328P compatible with Arduino board w/ Qwiic Connector and CH340C Serial-USB Converter IC Breadboardable R3 footprint microcontroller Improved reset button
Asin: B07MTQ8GJC | Model: DEV-15123 | PartNumber: DEV-15123 | Ean: 5060627392693, 0845156009145 | UPC: 845156009145
Hardware Peripherals You Know And Love: 20 Digital I/O Pins With 6 Pwm Pins, 6 Analog Inputs, Uart, Spi And External Interrupts.
The Sparkfun Qwiic Connect System Is An Ecosystem Of I2c Sensors, Actuators, Shields And Cables That Make Prototyping Faster And Less Prone To Error. All Qwiic-Enabled Boards Use A Common 1Mm Pitch, 4-Pin Jst Connector. This Reduces The Amount Of Required Pcb Space, And Polarized Connections Mean You Can’T Hook It Up Wrong..
Broken Out The Sda, Scl And Ioref Pins, So It Will Be Compatible With Future Shields Power Over Usb Or Through The Barrel Jack 7 To 15Vdc.
Program With A Usb Micro-B Cable Using The Arduino Ide Platform: Plug In The Board, Select “Arduino Uno” And You’Re Ready To Upload Code.
Features
- ATmega328 microcontroller with Optiboot (UNO) Bootloader. Rev3 shield compatible.
- Program with a USB Micro-B cable using the Arduino IDE platform: Plug in the board, select Arduino UNO and you re ready to upload code
- Hardware peripherals you know and love: 20 Digital I/O pins with 6 PWM pins, 6 Analog Inputs, UART, SPI and external interrupts
- Broken out the SDA, SCL and IOREF pins, so it will be compatible with future shields Power over USB or through the barrel jack 7 to 15VDC
- The SparkFun Qwiic Connect System is an ecosystem of I2C sensors, actuators, shields and cables that make prototyping faster and less prone to error. All Qwiic-enabled boards use a common 1mm pitch, 4-pin JST connector. This reduces the amount of required PCB space, and polarized connections mean you can t hook it up wrong.
- See more on Amazon...
Brand: SparkFun | Manufacturer: SparkFun Electronics
Dimensions: 0.51 x 2.83 x 2.17 inches
See On Amazon #18
SparkFun Simultaneous RFID Reader - M6E Nano Long distance UHF sensor shield Write tags at 80msec standard Read up to 150 tags/sec to 96-bit EPC
Asin: B06XGQM33F | Model: SEN-14066 | PartNumber: SEN-14066 | Ean: 0611138684873 | UPC: 611138684873
Whether You Want To Get Started By Adding An Rfid Reader On Your Toolbox With Tags On All Your Tools Or Allowing Access To The Tree House For Your Secret Society Meetings, This Board May Be For You!.
With The Correct Antenna You Can Read Up To 16 Feet (4.9M), Or 1 To 2 Feet With The Onboard Antenna.
You Can Also Connect Directly To Your Computer Using The Ftdi Header On The Board And Read Data Using The Universal Reader Assistant, Or A Different Microcontroller.
Radio Frequency Identification (Rfid) Is Becoming Popular Everywhere For Tracking Practically Everything.
Features
- The SparkFun Simultaneous RFID Reader is an Arduino-compatible board to get you started with the M6E Nano UHF RFID Reader
- Radio Frequency Identification (RFID) is becoming popular everywhere for tracking practically everything
- Whether you want to get started by adding an RFID reader on your toolbox with tags on all your tools or allowing access to the tree house for your secret society meetings, this board may be for you!
- You can also connect directly to your computer using the FTDI header on the board and read data using the Universal Reader Assistant, or a different microcontroller
- With the correct antenna you can read up to 16 feet (4.9m), or 1 to 2 feet with the onboard antenna
- See more on Amazon...
Brand: SparkFun | Manufacturer: SparkFun Electronics
Dimensions: 0.20 x 3.15 x 3.94 Inches | Weight: 0.01 Pounds
See On Amazon #19
SparkFun Motor Driver - Dual TB6612FNG (with Headers)
Asin: B07PV1S8HX | Ean: 0744790345797 | UPC: 744790345797
Standby Control To Save Power.
Assembled And Tested.
Built-In Thermal Shutdown Circuit And Low-Voltage Detecting Circuit.
Output Current: Iout = 1.2A (Average) / 3.2A (Peak).
Features
- Power supply voltage: VM = 15V max, VCC = 2.7--5.5V
- Output current: Iout = 1.2A (average) / 3.2A (peak)
- Standby control to save power
- Built-in thermal shutdown circuit and low-voltage detecting circuit
- Assembled and Tested
- See more on Amazon...
Brand: Electronics123.com, Inc. | Manufacturer: SparkFun Electronics
Dimensions: 1.00 x 1.00 x 1.00 inches
See On Amazon #20
SparkFun Pro Mini ATmega328-3.3V/8MHz Development Board Compatible with Arduino Boards and IDE
Asin: B004RF9LB8 | Model: DEV-11114 | PartNumber: DEV-11114 | Ean: 0748347526929, 0845156005727 | UPC: 845156005727, 748347526929
Supports Auto-Reset Has On Board Power And Status Leds.
Requires Soldering To Use. Choose Your Prefered Connectors, Solder, And Go!.
3.3V Regulator Max 150Ma Output.
No Usb Connection On Board. Need Ftdi Or Serial Board (Or Similar Device) To Program..
Features
- ATmega328 running at 8MHz with external resonator (0.5% tolerance)
- No USB connection on board. Need FTDI or serial board (or similar device) to program.
- Supports auto-reset Has On board Power and Status LEDs
- 3.3V regulator Max 150mA output
- Requires soldering to use. Choose your prefered connectors, solder, and go!
- See more on Amazon...
Brand: SparkFun | Manufacturer: SparkFun Electronics
Dimensions: 0.20 x 3.15 x 1.97 inches | Weight: 0.02 Pounds
See On Amazon #21
SparkFun FTDI Basic Breakout - 3.3V Development Tool with USB Mini-B Connector Save Space and Money in Your DIY Electronics Projects Pinout of This Board Matches The FTDI Cable
Asin: B079M4F7W5 | Model: RTL-09893 | PartNumber: RTL-09893 | Ean: 0799430213394, 0845156000791, 0845156598731, 0845156003587 | UPC: 845156000791, 799430213394, 845156003587, 845156598731
Designed To Decrease The Cost Of (Arduino-Compatible) Development And Increase Ease Of Use. Includes Auto-Reset Feature.
Uses A Smd 6-Pin Header On The Bottom, Which Makes It Smaller And More Compact.
The Pins Labeled Blk And Grn Correspond To The Black Wire On The Ftdi Cable That Is Gnd, Green Is Dtr.
Has Tx And Rx Leds That Allow You To See Serial Traffic On The Leds To Verify The Board Is Working.
Features
- Save space by using this genuine FTDI FT232RL USB to serial IC breakout to program your microcontroller
- Has TX and RX LEDs that allow you to see serial traffic on the LEDs to verify the board is working
- Designed to decrease the cost of (Arduino-compatible) development and increase ease of use. Includes auto-reset feature
- The pins labeled BLK and GRN correspond to the black wire on the FTDI cable that is GND, green is DTR
- Uses a SMD 6-pin header on the bottom, which makes it smaller and more compact
- See more on Amazon...
Brand: SparkFun | Manufacturer: SparkFun Electronics
Dimensions: 0.39 x 1.18 x 0.79 inches | Weight: 0.01 Pounds
See On Amazon #22
Wide Band 4G LTE Internal LoRa Antenna - Wide Band, 700-2700Mhz Frequency Range, 4G LTE Antenna Provides a Wide Enough Range for a Number of Applications Including BLE & LoRa/RF-53mm x 24mm
Asin: B08WJQ7ZS3 | Model: WRL-17841 | PartNumber: WRL-17841 | Ean: 0845156011261 | UPC: 845156011261
Features: Frequency Range: 700-2700Mhz, Gain: 8Dbi Internal Antenna, Vswr: ≤1.8, Input Impedance: 50Ω, Material: Radiator Fpc, Antenna Size: 53*24Mm, Length: 100Mm, Cable Type: 1.13 Coaxial Cable.
Antenna Only. Microcontroller Not Included..
Also Features: Connector Style: Ipex (U.Fl Equivalent), Polarization: Vertical, Power: 30W, Mounting: 3M Sticker, Operation Temperature: - 40 °C ~ + 80 °C, Storage Temperature: - 40 °C ~ + 80 °C.
This Antenna Is 53Mm X 24Mm With A 100Mm Length Coaxial Cable Ending In An Ipex (U.Fl Equivalent) Connector. The Antenna Has A 3M Adhesive Backing Making It Easy To Fix It To Your Project..
Features
- A Wide Band, 700-2700Mhz frequency range, 4G LTE antenna provides a wide enough range for a number of applications including BLE & LoRa/RF.
- This antenna is 53mm x 24mm with a 100mm length coaxial cable ending in an IPEX (u.FL equivalent) connector. The antenna has a 3M adhesive backing making it easy to fix it to your project.
- Features: Frequency range: 700-2700Mhz, Gain: 8dBi internal antenna, VSWR: 1.8, Input impedance: 50 , Material: Radiator FPC, Antenna Size: 53*24mm, Length: 100mm, Cable type: 1.13 coaxial cable
- Also features: Connector style: IPEX (u.FL equivalent), Polarization: Vertical, Power: 30w, Mounting: 3M sticker, Operation Temperature: - 40 C ~ + 80 C, Storage Temperature: - 40 C ~ + 80 C
- Antenna only. Microcontroller not included.
- See more on Amazon...
Brand: SparkFun | Manufacturer: SparkFun Electronics
Dimensions: 0.08 x 6.10 x 0.94 inches | Weight: 0.01 Pounds
See On Amazon #23
SparkFun Qwiic MultiPort Add I2C ports via Qwiic connectors to boards that only have one I2C port on their I2C bus Alternative daisy chained configuration 2x mounting holes Board size 1 inch by 1 inch
Asin: B09M9BX55S | Ean: 0845156011360 | UPC: 845156011360
This Board Has 2X Mounting Holes Located Around The Center..
Includes: 4X Qwiic Connectors; 2X 4-40 Mounting Points.
The Overall Size Of The Board Is 1.00" X 1.00". Each Connector Extending From The Center Has A Width Of About 0.30"..
Once Added, You Can Use It As A Hub To Add As Many I2c Devices To The Bus As You Need! You Can Also Use The Board As An Alternative To A Daisy Chained Configuration..
Features
- The SparkFun Qwiic Multiport adds additional ports to boards that have only one Qwiic port on their I2C bus.
- Once added, you can use it as a hub to add as many I2C devices to the bus as you need! You can also use the board as an alternative to a daisy chained configuration.
- This board has 2x mounting holes located around the center.
- The overall size of the board is 1.00 x 1.00. Each connector extending from the center has a width of about 0.30.
- Includes: 4x Qwiic Connectors; 2x 4-40 Mounting Points
- See more on Amazon...
Brand: SparkFun | Manufacturer: SparkFun Electronics
Dimensions: 0.20 x 1.81 x 1.18 inches | Weight: 0.01 Pounds
See On Amazon #24
SparkFun IoT RedBoard - ESP32 Development Board -ESP32 WROOM MCU Module USB-C Connector Qwiic Connector MicroSD Card -ESP32 Dimensions: 2.3in x 2.7in x 1.08in
Asin: B0BBXTJ62N | Ean: 0845156012770 | UPC: 845156012770
Also Features: WiFi, 802.11B/G/N. Bit Rate: 802.11N Up To 150Mbps. A-Mpdu And A-Msdu Aggregation. 0.4Μs Guard Interval Support. Center Frequency Range Of Operating Channel: 2412 ~ 2484Mhz..
The Iot Redboard Can Target A Wide Variety Of Applications, Ranging From Low-Power Sensor Networks To The Most Demanding Tasks, Such As Voice Encoding, Music Streaming, And Mp3 Decoding..
We've Included 3.3V Voltage Translation And A Qwiic Connector To The Edge Of The Board To Allow For Quick And Seamless Connection To Our Ever-Growing Line Of I2c Based Qwiic Products. The Board Even Includes A Microsd Socket If Your Application Requires You To Log And Save Data To A Memory Card..
Iot Redboard Features: Cpu And OnChip Memory. Esp32-D0wd-V3 Embedded, Xtensa Dual-Core 32-Bit Lx6 Microprocessor, Up To 240Mhz. 448Kb Rom. 520Kb Sram. 16Kb Sram In Rtc.
Features
- The IoT RedBoard is an ESP32 WROOM-equipped development board that has everything you need in an Uno with extra perks like USB-C, Qwiic, and more.
- IoT RedBoard Features: CPU and On Chip Memory. ESP32-D0WD-V3 embedded, Xtensa dual-core 32-bit LX6 microprocessor, up to 240MHz. 448KB ROM. 520KB SRAM. 16KB SRAM in RTC
- Also Features: Wi Fi, 802.11b/g/n. Bit rate: 802.11n up to 150Mbps. A-MPDU and A-MSDU aggregation. 0.4 s guard interval support. Center frequency range of operating channel: 2412 ~ 2484MHz.
- We've included 3.3V voltage translation and a Qwiic connector to the edge of the board to allow for quick and seamless connection to our ever-growing line of I2C based Qwiic products. The board even includes a microSD socket if your application requires you to log and save data to a memory card.
- The IoT RedBoard can target a wide variety of applications, ranging from low-power sensor networks to the most demanding tasks, such as voice encoding, music streaming, and MP3 decoding.
- See more on Amazon...
Brand: SparkFun | Manufacturer: SparkFun Electronics
Dimensions: 1.10 x 2.30 x 2.70 inches
See On Amazon #25
SparkFun EasyDriver Stepper Motor Driver
Asin: B004G4XR60 | Model: SX09402 | PartNumber: SX09402 | Ean: 0845156594023 | UPC: 845156594023
Power Supply Range From 7V To 30V. The Higher The Voltage, The Higher The Torque At High Speeds.
Adjustable Current Control From 150Ma/Phase To 750Ma/Phase.
Features
- MS1 and MS2 pins broken out to change microstepping resolution to full, half, quarter and eighth steps (defaults to eighth)
- Adjustable current control from 150mA/phase to 750mA/phase
- Power supply range from 7V to 30V. The higher the voltage, the higher the torque at high speeds
- See more on Amazon...
Brand: SparkFun | Manufacturer: Sparkfun Electronics
Dimensions: 0.39 x 3.31 x 2.68 inches | Weight: 0.01 Pounds
See On Amazon #26
Alchitry Cu FPGA Development Board (Lattice iCE40 HX) - a "Lighter" FPGA Version - Qwiic Connector for Easy I2C Integration
Asin: B08DJBYN5K | Ean: 0845156010684 | UPC: 845156010684
79 Io Pins (3.3V Logic Level). Usb-C To Configure And Power The Board. Eight General Purpose Leds. One Button (Typically Used As A Reset). Qwiic Connector.
Powered With 5V Through Usb-C Port, 0.1" Holes, Or Headers. Usb To Serial Interface For Data Transfer (Up To 12Mbaud). Dimensions Of 65Mm X 45Mm.
100Mhz On-Board Clock (Can Be Multiplied Internally By The Fpga).
Lattice Ice40-Hx8k Fpga - 7680 Logic Elements.
Features
- This board is a fantastic starting point into the world of FPGAs and the heart of your next project.
- Lattice iCE40-HX8K FPGA - 7680 logic elements
- 79 IO pins (3.3V logic level). USB-C to configure and power the board. Eight general purpose LEDs. One button (typically used as a reset). Qwiic Connector
- 100MHz on-board clock (can be multiplied internally by the FPGA)
- Powered with 5V through USB-C port, 0.1 holes, or headers. USB to serial interface for data transfer (up to 12Mbaud). Dimensions of 65mm x 45mm
- See more on Amazon...
Brand: SparkFun | Manufacturer: SparkFun Electronics
Dimensions: 0.28 x 1.77 x 2.52 inches | Weight: 0.04 Pounds
See On Amazon #27
SparkFun XBee Explorer Dongle - Red
Asin: B011QJIHY4 | Model: WRL-11697 | PartNumber: WRL-11697 | Ean: 0845156598199, 0717520027379 | UPC: 717520027379, 845156598199
This Unit Works With All Xbee Modules Including The Series 1 And Series 2.5, Standard And Pro Version.
Ft231x Usb-To-Serial Converter.
Features
- Plug the unit directly into your USB port and have it act as a gateway between your computer and the XBee.
- FT231X USB-to-Serial converter
- This unit works with all XBee modules including the Series 1 and Series 2.5, standard and Pro version
- See more on Amazon...
Brand: SparkFun | Manufacturer: Sparkfun Electronics
Dimensions: 0.24 x 2.17 x 1.10 inches | Weight: 0.03 Pounds
See On Amazon #28
SparkFun GPS-RTK Dead Reckoning Kit (SMA) Sensor Fusion GPS Board, 184-channel u-blox F9 Engine GNSS Receiver, Reversible USB A to C Cable - 0.8m, Board Dimensions: 60.0mm x 82.0mm x 22.5mm
Asin: B0CQ745H6Z | Model: KIT-23452 | PartNumber: KIT-23452 | Ean: 0845156013845 | UPC: 845156013845
Features: 2X Qwiic Connectors, Integrated Sma Connector For Use With Antenna Of Your Choice, Concurrent Reception Of Gps, Glonass, Galileo And Beidou, 184-Channel Gnss Receiver, Receives Both L1c/A And L2c Bands..
Also Included With This Kit Is A Gnss Multiband Antenna And A Reversible Usb-A To C Cable. The Antenna Features A Magnetic Base Receiving The Classic L1 And L2 Gps Bands. Meanwhile, The Included Cables Will Make Sure Hooking Up Each Part In The Kit Is Easy!.
This Breakout Maximizes Position Accuracy In Dense Cities Or Covered Areas Compared To Other Gps Modules. Even Under Poor Signal Conditions, Continuous Positioning Is Provided In Urban Environments And Available During Complete Signal Loss (E.G., Short Tunnels And Parking Garages). The Zed-F9r Is The Ultimate Solution For Autonomous Robotic Applications That Require Accurate Positioning Under Challenging Conditions..
Includes: 1X Sparkfun Gps-Rtk Dead Reckoning Breakout - Zed-F9r, Sma (Qwiic) 1X Gnss Multi-Band Magnetic Mount Antenna - 5M (Sma) 1X Reversible Usb A To C Cable - 0.8M..
Features
- The SparkFun GPS-RTK Dead Reckoning Kit provides you with what you need to start with GPS Real Time Kinematics and the u-blox ZED-F9R.
- Includes: 1x SparkFun GPS-RTK Dead Reckoning Breakout - ZED-F9R, SMA (Qwiic) 1x GNSS Multi-Band Magnetic Mount Antenna - 5m (SMA) 1x Reversible USB A to C Cable - 0.8m.
- Features: 2x Qwiic Connectors, Integrated SMA connector for use with antenna of your choice, Concurrent reception of GPS, GLONASS, Galileo and BeiDou, 184-Channel GNSS Receiver, Receives both L1C/A and L2C bands.
- This breakout maximizes position accuracy in dense cities or covered areas compared to other GPS modules. Even under poor signal conditions, continuous positioning is provided in urban environments and available during complete signal loss (e.g., short tunnels and parking garages). The ZED-F9R is the ultimate solution for autonomous robotic applications that require accurate positioning under challenging conditions.
- Also included with this kit is a GNSS multiband antenna and a reversible USB-A to C cable. The antenna features a magnetic base receiving the classic L1 and L2 GPS bands. Meanwhile, the included cables will make sure hooking up each part in the kit is easy!
- See more on Amazon...
Brand: SparkFun | Manufacturer: SparkFun Electronics
Dimensions: 1.38 x 5.12 x 3.94 inches | Weight: 0.50 pounds
See On Amazon