Peachtree Woodworking Supply Performax Type Ready-to-Cut Ready-to-Wrap Abrasive Sandpaper Rolls 3 inch by 35 feet Long for 16-32 Drum Sanders
Asin: B000H5LY08 | Ean: 0810948010258 | UPC: 810948010258
As an Amazon Associate we earn a fee from qualifying purchases when you follow a link to Amazon from this page. We rank the products, but the links to Amazon are promotional.The Right Amount Of Pressure You Exert On Your Boards Is Absolutely Critical. Too Much And It Will Shorten The Life Of Your Abrasive Roll, Burn The Material Or Cause Problems With The Motor On Your Machinery. To Avoid Too Much Pressure, With Your Machine Turned Off, Place The Material Under The Sanding Drum, The Raise Or Lower The Drum So The Drum Contacts The Material But Can Still Be Rotated By Hand. Take The Stock Out With No More Drum Adjustment And Proceed To Sanding Normally..
When Sanding Misshapen Stock Pieces You Should Always Start Sanding The Piece With The Crown Side Up. This Helps Prevent Tipping Or Rocking When The Piece Is Being Fed Through The Sander. Once The Down Is Gone, Flip The Stock Over And Sand The Other Side. As Always, Take Extreme Care And Caution When Sanding Boards That Are Bowed, Twisted Or Otherwise Imperfect..
Straight Feed? How About Angling Your Stock Feed Through The Drum Instead. Angling The Stock Offers Many Advantages Like Less Loading Due To Glue Lines, Better And More Even Wear And Reduced Motor Loads. Just A Slight Angle Provides You With More Effective Stock Removal. Keep In Mind That To Achieve The Best Finish, The Last Two Passes On The Material Should Always Be With The Grain..
The Rougher Or Lower Grits Like 60 Grit Can Be Used For Abrasive Planing And Dimensioning. The Medium Grits Like 80, 100 And 120 Are Typically Can Be Used For Lighter Dimensioning Projects And General Surface Prep. When Using 150 Grits And 220 Grits We Recommend Using Those Higher Grits For Finishing Passes Only..
Features
- Made from heavy duty cloth backing our abrasive rolls are the perfect economical replacement sandpaper rolls for your Performax and Jet 16-32 and other machinery that accepts 3 wide rolls. These high performance aluminum oxide rolls are designed for all purpose sanding. The grain is resin bonded and have non-loading properties for extra long sanding life. MADE IN THE USA!
- The rougher or lower grits like 60 grit can be used for abrasive planing and dimensioning. The medium grits like 80, 100 and 120 are typically can be used for lighter dimensioning projects and general surface prep. When using 150 grits and 220 grits we recommend using those higher grits for finishing passes only.
- The right amount of pressure you exert on your boards is absolutely critical. Too much and it will shorten the life of your abrasive roll, burn the material or cause problems with the motor on your machinery. To avoid too much pressure, with your machine turned off, place the material under the sanding drum, the raise or lower the drum so the drum contacts the material but can still be rotated by hand. Take the stock out with no more drum adjustment and proceed to sanding normally.
- Straight feed? How about angling your stock feed through the drum instead. Angling the stock offers many advantages like less loading due to glue lines, better and more even wear and reduced motor loads. Just a slight angle provides you with more effective stock removal. Keep in mind that to achieve the best finish, the last two passes on the material should always be with the grain.
- When sanding misshapen stock pieces you should always start sanding the piece with the crown side up. This helps prevent tipping or rocking when the piece is being fed through the sander. Once the down is gone, flip the stock over and sand the other side. As always, take extreme care and caution when sanding boards that are bowed, twisted or otherwise imperfect.
- See more on Amazon...
Brand: Peachtree Woodworking Supply | Manufacturer: Keystone
Dimensions: 0.01 x 35.00 x 3.00 inches
See On Amazon Similar To Peachtree Woodworking Supply Performax Type
#1
Peachtree Woodworking Supply Pro Grind Sharpening System for 6 Inch Grinders to Sharpen Lathe Turning Tools, Chisels, Skews, Bowl Spindle Gouges Includes Setup Blocks and Quad Jig for 6 inch Grinders
Asin: B0CMVN1JKZ | Model: 7575-PT6 | PartNumber: 7575-PT6 | Ean: 0817918024239 | UPC: 817918024239
The Pro Grind Tool Rest Bar Attachment Offers You The Best Possible Way To Achieve A Precise Edge To Your Bevels Without Taking Of Too Much Material Off Of Your Tool. After All, We Need Our Tools To Last A Long Time, So Why Would You Want To Take Off To Much At A Time? The Tool Rest Bar Is Ideal For Sharpening Curved, Even Bevel Edges That Are Typically Used On Spindle And Roughing Gouges..
The Pro Grind Sharpening System Also Comes With A Number Of Setup Jigs And Accessories To Help In The Setup Process To Sharpen Your Tools To The Proper And Repeatable Angles. From The Built-In Projection Gauge On The Multi-Grind Arm To The Magnetic Micro Bevel Setup Block You’Ll Be Able To Achieve Consistent Repeatable Angles And Produce Excellent Results Each And Every Time You Use The Pro Grind Sharpening Jig System..
The Large, 3” X 5” Slotted Platform Is The Ideal Way To Sharpen Flat Edged Tools Like Wood Turning Skews, Chisels And Hand Plane Irons. The Platform Has A Slot Milled Horizontally Through It So It Can Accept The Included Tool Holder. The Tool Holder Is Designed To Keep Your Tools At The Correct Angle While Being Able To Slide Side To Side During The Sharpening Process..
The Included And Versatile Multi-Grind Jig Will Correctly Shape The Edge On Bowl Gouges, Side Grinds (Aka Ellsworth Grind, Liam O’Neil Grind/Irish Grind) Or Fingernail Grinds For Spindle Work And Detailing. Not Only Will It Correctly Shape Your Tools, You Will Also Be Able To Repeat The Process To Produce Consistent Results Every Time. The Multi-Grind Jig Is Designed To Be Used With The Included Multi-Grind Arm On The Pro Grind Sharpening System And Will Accept Tools Up To 1.125” In Diameter..
Features
- Sharpen chisels, gouges, bowl gouges, spindle gouges, carving tools, wood turning scrapers, parting tools, block plane irons and more with the PRO GRIND Sharpening System! With 3 primary methods of sharpening, you ll be able to precisely hone each tool to your exacting specifications regardless of the tool you are sharpening. The PRO GRIND Sharpening System includes a vast collection of unique setup tools, jigs and accessories that most sharpening systems force you to purchase separately
- The included and versatile Multi-Grind Jig will correctly shape the edge on bowl gouges, side grinds (aka Ellsworth grind, Liam O Neil grind/Irish grind) or fingernail grinds for spindle work and detailing. Not only will it correctly shape your tools, you will also be able to repeat the process to produce consistent results every time. The Multi-Grind Jig is designed to be used with the included Multi-Grind arm on the PRO GRIND Sharpening System and will accept tools up to 1.125 in diameter.
- The PRO GRIND Tool Rest Bar attachment offers you the best possible way to achieve a precise edge to your bevels without taking of too much material off of your tool. After all, we need our tools to last a long time, so why would you want to take off to much at a time? The Tool Rest Bar is ideal for sharpening curved, even bevel edges that are typically used on spindle and roughing gouges.
- The large, 3 x 5 slotted platform is the ideal way to sharpen flat edged tools like wood turning skews, chisels and hand plane irons. The platform has a slot milled horizontally through it so it can accept the included tool holder. The tool holder is designed to keep your tools at the correct angle while being able to slide side to side during the sharpening process.
- The PRO GRIND Sharpening System also comes with a number of setup jigs and accessories to help in the setup process to sharpen your tools to the proper and repeatable angles. From the built-in projection gauge on the Multi-Grind arm to the Magnetic Micro Bevel setup block you ll be able to achieve consistent repeatable angles and produce excellent results each and every time you use the PRO GRIND Sharpening Jig system.
- See more on Amazon...
Brand: Peachtree Woodworking Supply | Manufacturer: Savannah
Dimensions: 4.00 x 30.00 x 9.00 inches
See On Amazon #2
Peachtree Woodworking Supply Performax Type Ready to Cut Wrap Abrasive Sandpaper Rolls 3 inch by 35 feet Long for 16-32 Drum Sanders
Asin: B000H5IJP6 | Model: 5 | PartNumber: 5 | Ean: 0810948010227 | UPC: 810948010227
The Right Amount Of Pressure You Exert On Your Boards Is Absolutely Critical. Too Much And It Will Shorten The Life Of Your Abrasive Roll, Burn The Material Or Cause Problems With The Motor On Your Machinery. To Avoid Too Much Pressure, With Your Machine Turned Off, Place The Material Under The Sanding Drum, The Raise Or Lower The Drum So The Drum Contacts The Material But Can Still Be Rotated By Hand. Take The Stock Out With No More Drum Adjustment And Proceed To Sanding Normally..
When Sanding Misshapen Stock Pieces You Should Always Start Sanding The Piece With The Crown Side Up. This Helps Prevent Tipping Or Rocking When The Piece Is Being Fed Through The Sander. Once The Down Is Gone, Flip The Stock Over And Sand The Other Side. As Always, Take Extreme Care And Caution When Sanding Boards That Are Bowed, Twisted Or Otherwise Imperfect..
Straight Feed? How About Angling Your Stock Feed Through The Drum Instead. Angling The Stock Offers Many Advantages Like Less Loading Due To Glue Lines, Better And More Even Wear And Reduced Motor Loads. Just A Slight Angle Provides You With More Effective Stock Removal. Keep In Mind That To Achieve The Best Finish, The Last Two Passes On The Material Should Always Be With The Grain..
The Rougher Or Lower Grits Like 60 Grit Can Be Used For Abrasive Planing And Dimensioning. The Medium Grits Like 80, 100 And 120 Are Typically Can Be Used For Lighter Dimensioning Projects And General Surface Prep. When Using 150 Grits And 220 Grits We Recommend Using Those Higher Grits For Finishing Passes Only..
Features
- Made from heavy duty cloth backing our abrasive rolls are the perfect economical replacement sandpaper rolls for your Performax and Jet 16-32 and other machinery that accepts 3 wide rolls. These high performance aluminum oxide rolls are designed for all purpose sanding. The grain is resin bonded and have non-loading properties for extra long sanding life. MADE IN THE USA!
- The rougher or lower grits like 60 grit can be used for abrasive planing and dimensioning. The medium grits like 80, 100 and 120 are typically can be used for lighter dimensioning projects and general surface prep. When using 150 grits and 220 grits we recommend using those higher grits for finishing passes only.
- The right amount of pressure you exert on your boards is absolutely critical. Too much and it will shorten the life of your abrasive roll, burn the material or cause problems with the motor on your machinery. To avoid too much pressure, with your machine turned off, place the material under the sanding drum, the raise or lower the drum so the drum contacts the material but can still be rotated by hand. Take the stock out with no more drum adjustment and proceed to sanding normally.
- Straight feed? How about angling your stock feed through the drum instead. Angling the stock offers many advantages like less loading due to glue lines, better and more even wear and reduced motor loads. Just a slight angle provides you with more effective stock removal. Keep in mind that to achieve the best finish, the last two passes on the material should always be with the grain.
- When sanding misshapen stock pieces you should always start sanding the piece with the crown side up. This helps prevent tipping or rocking when the piece is being fed through the sander. Once the down is gone, flip the stock over and sand the other side. As always, take extreme care and caution when sanding boards that are bowed, twisted or otherwise imperfect.
- See more on Amazon...
Brand: Peachtree Woodworking Supply | Manufacturer: Keystone
Dimensions: 0.10 x 420.00 x 3.00 inches
See On Amazon #3
Peachtree Woodworking Supply Mounting Track Base Add On for the Tool Rest Sharpening Jig
Asin: B07VB9B2D3 | Ean: 0817918021610 | UPC: 817918021610
When You’Re Done With One Grit For Your Tool, Simply Loosen The Sharpening Jig Knob, Slide The Jig Out And Then Slide The Jig Back Into The Other Side! It Literally Takes Seconds To Switch From One Wheel To Another! This Makes The Tools Rest Sharpening Jig Even More Versatile Than It Already Is!.
If You Already Own The Jig, Then You Owe To Yourself To Get At Least One Mounting Track, If You Are Thinking About Purchasing The Tool Rest Sharpening Jig, Then We Encourage You To Consider Getting An Extra Mounting Track To Conveniently Work Both Wheels On Your Grinder. The Mounting Track Is Installed Using Four Wood Screws Which Are Included..
Made From The Exact Same Extruded Aluminum Material As The Original Mounting Track. The Mounting Track Not Only Allows Quick Switch Outs But It Also Allows You To Quickly Adjust The Jig Forward Or Backward Depending On What Type Of Tool You Are Sharpening..
Now, With An Extra Mounting Track Base You Can Have A Mounting Track For Each Of Your Two Wheels On Your Grinder! Once Both Mounting Tracks Have Been Installed, All You Have To Do Is Slide The Sharpening Jig Into One Side Or The Other And Start Sharpening!.
Features
- If you already own one of the Tool Rest Sharpening Jigs, then you know how versatile it is. Being able to accurately hone your tools can certainly be satisfying. Sometimes though it would be nice if we could have the ability to move the sharpening jig to the other side of the bench grinder to sharpen your tools with a different grit wheel.
- Now, with an extra Mounting Track Base you can have a mounting track for each of your two wheels on your grinder! Once both Mounting Tracks have been installed, all you have to do is slide the Sharpening Jig into one side or the other and start sharpening!
- When you re done with one grit for your tool, simply loosen the sharpening jig knob, slide the jig out and then slide the jig back into the other side! It literally takes seconds to switch from one wheel to another! This makes the Tools Rest Sharpening Jig even more versatile than it already is!
- Made from the exact same extruded aluminum material as the original Mounting Track. The Mounting Track not only allows quick switch outs but it also allows you to quickly adjust the jig forward or backward depending on what type of tool you are sharpening.
- If you already own the jig, then you owe to yourself to get at least one Mounting Track, if you are thinking about purchasing the Tool Rest Sharpening Jig, then we encourage you to consider getting an extra Mounting Track to conveniently work both wheels on your grinder. The Mounting Track is installed using four wood screws which are included.
- See more on Amazon...
Brand: Peachtree Woodworking Supply | Manufacturer: Peachtree Woodworking Supply Inc.
See On Amazon #4
Peachtree Woodworking 4" RECTANGULAR BELL DUST PORT - PW390
Asin: B001397R58 | Ean: 0810948016267 | UPC: 810948016267
The Long Neck Allows For A 4" Hose To Be Secured In Place.
Measures 9-1/2" Long By 4-1/2" Wide..
A Hose Clamp Is Required For Proper Connection. (Hose Clamps Sold Separately).
Generally Used On Larger Machines Such As The Table Saw Or Joiner..
Features
- 4" Rectangular Bell Dust port sets up similar to a flange.
- Generally used on larger machines such as the table saw or joiner.
- The long neck allows for a 4 hose to be secured in place
- A hose clamp is required for proper connection. (HOSE CLAMPS SOLD SEPARATELY)
- Measures 9-1/2 long by 4-1/2 wide.
- See more on Amazon...
Brand: Peachtree Woodworking | Manufacturer: Peachtree Woodworking
See On Amazon #5
Peachtree Woodworking Supply Deluxe Starter Pen Turning Kit (Classic Slim Style)
Asin: B06XC13DF5 | Ean: 0817918020156 | UPC: 817918020156
1 Each Chrome Pen Kit And 1 Each Gold Pen Kit Included.
Read Full Description Below For Complete List Of Included Parts.
Everything Included In One Convenient Storage Case.
Ideal For Any Level Of Woodturner.
Features
- Create a custom pen as the perfect gift or keepsake
- Ideal for any level of woodturner
- 1 each chrome pen kit and 1 each gold pen kit included
- Everything included in one convenient storage case
- Read full description below for complete list of included parts
- See more on Amazon...
Brand: Peachtree Woodworking Supply | Manufacturer: Peachtree Woodworking Supply Inc.
See On Amazon #6
Peachtree Woodworking Featherboard Locking Kit - PW1139
Asin: B0009ZZDVC | Ean: 0810948013440 | UPC: 810948013440
Locks All Type Of Featherboards Onto Table Saws, Router Tables & Band Saws..
Add One To Each Of Your Featherboards For Added Safety..
Kit Includes 7 Pieces: 2- T-Slot Pieces, 2- 1/4" - 20 Bolts, 2- Knobs, 1- Nylon Lock Knob..
The T-Bar Will Fit Any 3/4" X 3/8" Miter T-Slot..
Features
- Miter slot locking kit locks custom jigs & fixtures in any t-slot grove.
- The t-bar will fit any 3/4 x 3/8 miter t-slot.
- Locks all type of featherboards onto table saws, router tables & band saws.
- Kit Includes 7 pieces: 2- T-slot pieces, 2- 1/4 - 20 Bolts, 2- Knobs, 1- Nylon Lock Knob.
- Add one to each of your featherboards for added safety.
- See more on Amazon...
Brand: Peachtree Woodworking | Manufacturer: PEACHTREE WOODWORKING
See On Amazon #7
Peachtree Woodworking Down Draft Panel Set of 2 - PW3592
Asin: B00405NTTA | Ean: 0814310010334 | UPC: 814310010334
Orange Stops Included To Prevent Stock Movement While Sanding.
The Set Includes 2 Down Draft Panels..
Stops Can Be Placed In Any Of The Open Holes On The Plate.
Has Soft, Non-Slip Rubber Grommets To Prevent Marking The Stock.
Features
- Each plate measures 6 3/4" x 16 1/2"
- Has soft, non-slip rubber grommets to prevent marking the stock
- Orange stops included to prevent stock movement while sanding
- Stops can be placed in any of the open holes on the plate
- The set includes 2 down draft panels.
- See more on Amazon...
Brand: Peachtree Woodworking | Manufacturer: Peachtree Woodworking
See On Amazon
Looking For Something Else?
Search