Peachtree Woodworking Supply 22" Miter Extension Fence - PW1099
Asin: B000O2KNJ2 | Ean: 0810948011897 | UPC: 810948011897
As an Amazon Associate we earn a fee from qualifying purchases when you follow a link to Amazon from this page. We rank the products, but the links to Amazon are promotional.Adjustable Aluminum Fence Increases The Face Of Your Miter Gauge Or Saw..
Stop Block With Knobs And Bolts Included..
Built In Extension Bar To Increase The Stop Capacity To 36"..
Works On The Left Side Or Right Side Of Your Saw..
Features
- Will improve work support close to the saw blade.
- Works on the left side or right side of your saw.
- Adjustable aluminum fence increases the face of your miter gauge or saw.
- Built in extension bar to increase the stop capacity to 36.
- Stop block with knobs and bolts included.
- See more on Amazon...
Brand: Peachtree Woodworking Supply | Manufacturer: Peachtree Woodworking
See On Amazon Similar To Peachtree Woodworking Supply 22 Miter
#1
CRAFTSMAN Mitre Saw, 12-Inch Saw & Clamping Box (CMHT20600)
Asin: B07RBMNCDQ | Model: CMHT20600 | PartNumber: CMHT20600 | Ean: 0885911594509 | UPC: 885911594509
Extended Lip On Base Holds Mitre Box In Place While Cutting And A Built-In Saw Stop Helps Prevent Cutting Into Mitre Box.
Convenient Storage: Molded-In Storage Bins To Hold Cam Pins And Pencil.
Multiple Cut Angles: Cuts Mitres On 45-Degree And 90-Degree Angles And Face Angles On 45 Degree And 22.5 Degree For Octagonal Shapes.
Features
- ACCURACY: The hand miter saw has cam-shaped pins twist and lock with honeycomb base to secure work for accurate cuts
- MULTIPLE CUT ANGLES: Cuts mitres on 45-degree and 90-degree angles and face angles on 45 degree and 22.5 degree for octagonal shapes
- Extended lip on base holds mitre box in place while cutting and a built-in saw stop helps prevent cutting into mitre box
- CONVENIENT STORAGE: Molded-in storage bins to hold cam pins and pencil
- See more on Amazon...
Brand: CRAFTSMAN | Manufacturer: CRAFTSMAN
Weight: 0.00 pounds
See On Amazon #2
Fulton Precision Miter Gauge with Aluminum Miter Fence with 45 degree Angled Ends for Maximum Stock Support and a Repetitive Cut Flip Stop
Asin: B087XWCV61 | Model: 11567 | PartNumber: 11567 | Ean: 0817918022532 | UPC: 817918022532
The Head Is Mounted To A Solid Steel Miter Bar That Measure 18” In Length And Is .354” Thick By .730” Wide. Standard Miter Slots Are 3/4” X 3/8” With A 1/8” “T” Slot (Slight Variances From Brand To Brand) Running The Length On The Bottom Of The Slot. The Steel Miter Bar Is Equipped With A Metal, Removable Retaining Disc That Measures 7/8” In Diameter And Is Just Shy Of 1/8” To Fit Into To The “T” Slot To Prevent Accidental Lifting When Feeding Your Stock Through..
Both Ends Of The Fence Are Cut At Exactly 45 Degrees. This Allows You To Position The Fence Extra Close To The Saw Blade (With The Power Turned Off) So You Have Even More Control Over The Workpiece You Are Cutting. The Fence Comes With A Flip Stop That Makes Repetitive Cuts A Breeze. When Not In Use The Flip Stop Can Be Flipped Up And Out Of The Way. Also Include Are Two Sticky Back Measuring Tapes. 1 Tape Is Left To Right Reading And The Other Is Right To Left Reading..
Made From A Single Piece Of Extruded Aluminum, This Precision Miter Gauge Fence Is Not Only Durable, Its Accurate And Saves Setup Time. The Fence Is Designed To Be Used With Most Any Miter Gauge With Its Off-Set Mounting Track On The Back Of The Fence. The Off-Set Track Allows You To Flip The Fence For Lower Profile Miter Gauge Mounts And Flip Back For Standard Height Miter Gauges. The Fence Can Be Mounted To Older Miter Gauges By Adding A Wooden Block Mount With Wooden Screws If Necessary..
The .200” Thick, Adjustable, Solid Aluminum Head Is Machined With 13 Positive Stop Holes. 1 Hole Is At 90 Degrees While The 6 Holes On Both Sides Are At 22.5, 30, 45, 60, 67.5 And 90 Degrees. The Positive Stops Are Perfect For Many Woodworking Projects As They Are The Angles That Are Typically Used.To Adjust The Head You Simply Loosen The Post Knob Handle, Pull The Spring Loaded Indexing Pin Outward, Rotate The Head To The Desired Position, Release The Pin And Lock Into Place..
Features
- The Fulton Miter Gauge is a high quality, well thought out and economical solution for your table saw cross cutting needs.The Aluminum Miter fence is equally well thought out with its 45 degree ends for unsurpassed workpiece support and its ability to mounted to most any miter gauge. Also included is a handy aluminum flip stop for repetitive angled cuts on your table saw. Together these three items are the perfect compliment to each other for your table saw cutting needs.
- The .200 thick, adjustable, solid aluminum head is machined with 13 positive stop holes. 1 hole is at 90 degrees while the 6 holes on both sides are at 22.5, 30, 45, 60, 67.5 and 90 degrees. The positive stops are perfect for many woodworking projects as they are the angles that are typically used.To adjust the head you simply loosen the post knob handle, pull the spring loaded indexing pin outward, rotate the head to the desired position, release the pin and lock into place.
- The head is mounted to a solid steel miter bar that measure 18 in length and is .354 thick by .730 wide. Standard miter slots are 3/4 x 3/8 with a 1/8 T slot (slight variances from brand to brand) running the length on the bottom of the slot. The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8 in diameter and is just shy of 1/8 to fit into to the T slot to prevent accidental lifting when feeding your stock through.
- Made from a single piece of extruded aluminum, this precision miter gauge fence is not only durable, its accurate and saves setup time. The fence is designed to be used with most any miter gauge with its off-set mounting track on the back of the fence. The off-set track allows you to flip the fence for lower profile miter gauge mounts and flip back for standard height miter gauges. The fence can be mounted to older miter gauges by adding a wooden block mount with wooden screws if necessary.
- Both ends of the fence are cut at exactly 45 degrees. This allows you to position the fence extra close to the saw blade (with the power turned off) so you have even more control over the workpiece you are cutting. The fence comes with a flip stop that makes repetitive cuts a breeze. When not in use the flip stop can be flipped up and out of the way. Also include are two sticky back measuring tapes. 1 tape is left to right reading and the other is right to left reading.
- See more on Amazon...
Brand: Fulton | Manufacturer: Fulton Woodworking Tools Inc.
Dimensions: 0.00 x 0.00 x 0.00 inches | Weight: 2.50 pounds
See On Amazon #3
CRAFTSMAN Miter Box, Hand Miter Saw, Adjustable Angle Hand Saw (CMHT20800)
Asin: B07R4BVSB4 | Model: CMHT20800 | PartNumber: CMHT20800 | Ean: 0885911576369 | UPC: 885911576369
Secure Material: Clamps Hold Work In Place And Work Stop Allows For Quick, Repetitive Cuts.
Long Lasting Sharpness: Induction Hardened Teeth.
Ease Of Use: Easy Angle Adjustment And Comfortable Grip.
Features
- The hand miter saw is designed for precision wood cutting
- EASE OF USE: Easy angle adjustment and comfortable grip
- SECURE MATERIAL: Clamps hold work in place and work stop allows for quick, repetitive cuts
- LONG LASTING SHARPNESS: Induction hardened teeth
- See more on Amazon...
Brand: CRAFTSMAN | Manufacturer: CRAFTSMAN
Weight: 7.04 pounds
See On Amazon #4
POWERTEC Universal Table Saw Miter Gauge and Aluminum Miter Bar, 27 Angle Stops Miter Gauge, Works w/Table Saws, Band Saw, Router Table (71142)
Asin: B07TJX3FB9 | Model: 71142 | PartNumber: 71142 | Ean: 0843441104186 | UPC: 843441104186
Features: A Lightweight Design With A Durable Laser-Cut Aluminum Construction, Large Gauge Handle, Universal Fence Mounting Bracket, Pivoting Locking Mechanism, A Removal Plate That Allows The Miter Gauge To Be Used With T-Slotted And Non T-Slotted Miter Slots, And Adjustable Expansion Discs That Remove All Side Play From The Bar, Creating A Perfect Fit..
Universal Design: Works With Most Contractor Style, Full Sized Saws, Or Tools With Standard Miter Slots (3/4” Width X 3/8” Depth) With Or Without T-Slots, Making It Compatible With Popular Brand Table Saws, Band Saws, Router Tables, Disk And Belt Sanders. Please Note : Will Not Work With Smaller Saws Or Tool With 5/8” Miter Slots..
Precision: Angle Guide With 27 Total Locking Stops In 5 Degree Increments Over A Full 180-Degree Range, And Allows For Plus Or Minus 60-Degree Range Miter Cuts.
Function: A High Performance Woodworking Angle Tool That Possesses A Miter Guide Which Mounts Into The Miter Slots Of Your Table Saw (Band Saws And Other Applications) And Then Guides The Miter Gauge Parallel To The Blade For High Precision Angled And Crosscuts.
Features
- INCLUDES: (1) Miter Gauge for Table Saw
- FUNCTION: A high performance woodworking angle tool that possesses a miter guide which mounts into the miter slots of your table saw (band saws and other applications) and then guides the miter gauge parallel to the blade for high precision angled and crosscuts
- FEATURES: A lightweight design with a durable laser-cut aluminum construction, large gauge handle, universal fence mounting bracket, pivoting locking mechanism, a removal plate that allows the miter gauge to be used with T-slotted and non T-slotted miter slots, and adjustable expansion discs that remove all side play from the bar, creating a perfect fit.
- PRECISION: Angle guide with 27 total locking stops in 5 degree increments over a full 180-degree range, and allows for plus or minus 60-degree range miter cuts
- UNIVERSAL DESIGN: Works with most Contractor style, full sized saws, or tools with standard miter slots (3/4 width x 3/8 depth) with or without T-slots, making it compatible with popular brand table saws, band saws, router tables, disk and belt sanders. PLEASE NOTE : will not work with smaller saws or tool with 5/8 miter slots.
- See more on Amazon...
Brand: POWERTEC | Manufacturer: POWERTEC
Dimensions: 2.50 x 18.94 x 4.75 inches | Weight: 2.58 pounds
See On Amazon #5
POWERTEC Precision Table Saw Miter Gauge System w/ 27 Angle Stops and 3/4" x 3/8" T-Slotted Miter Bar w/Removable T-Slot Plate, Includes 24" x 3" Multi T Track Fence w/Scale, T-track Flip Stop, 71391V
Asin: B0CB854P9V | Model: 71391V | PartNumber: 71391V | Ean: 0843441124733 | UPC: 843441124733
High Precision Miter Gauge: Features 27 Angle Indexing Stops With 1-Degree Step Spacing And Positive Stops At 0°, 10°, 22½°, 30°And 45°And Nine Others, Both Left And Right (Works In Standard 3/4” X 3/8” Miter Slot, With Or Without T-Slots, But Will Not Work With Smaller Saws Or Tool With 5/8” Miter Slots.), Built-In.
Miter Saw Flip Stop: Delivers Exceptional Cut-Length Control, With A Toolless Locking Mechanism And Adjustable Settings To Quick Change To The Left Or Right Side Of The Blade.
Multi-Track Miter Fence: Smooth, Built-In Laser Engraved Measuring Scale, Extruded Aluminum Profile With A Universal Design That Accepts Accept 1/4"-20 Hex Bots, 1/4” T-Bolts And 5/16” T- Bolts, And T-Track Accessories.
Function: Cost Effective 3-Piece Set Designed To Give You Everything You Need To Produce Higher Precision Cuts (Including Cross Cutting) While With Quick And Accurate Project Results.
Features
- Includes: (1) table saw miter gauge, (1) multi-track miter fence, (1) t-track flip stop
- Function: cost effective 3-piece set designed to give you everything you need to produce higher precision cuts (including cross cutting) while with quick and accurate project results
- High precision miter gauge: features 27 angle indexing stops with 1-degree step spacing and positive stops at 0 , 10 , 22 , 30 and 45 and nine others, both left and right (Works in standard 3/4 x 3/8 miter slot, with or without t-slots, but will not work with smaller saws or tool with 5/8 miter slots.), Built-in
- Multi-track miter fence: smooth, built-in laser engraved measuring scale, extruded aluminum profile with a universal design that accepts accept 1/4-20 hex Bots, 1/4 t-bolts and 5/16 T- bolts, and T-track accessories
- Miter saw flip stop: delivers exceptional cut-length control, with a toolless locking mechanism and adjustable settings to quick change to the left or right side of the blade
- See more on Amazon...
Brand: POWERTEC | Manufacturer: POWERTEC
See On Amazon #6
Fulton Precision Miter Gauge with a Standard Slot (3/4 x 3/8 ) Steel Bar with Adjustable Spring Loaded Plungers and Removable Retaining Disc
Asin: B072WBLNDD | Model: 1250 | PartNumber: 1250 | Ean: 0810948015604 | UPC: 810948015604
To Adjust The Head You Simply Loosen The Post Knob Handle, Pull The Spring Loaded Indexing Pin Outward, Rotate The Head To The Desired Position, Release The Pin And Lock Into Place By Tightening The Post Knob Handle. The Aluminum Head Has Two ¼” X ½” Slots Milled Into It For Mounting A Miter Fence If So Desired. The Slots Are Approximately 1-1/8” From The Base Of The Miter Gauge Head..
The Steel Miter Bar Is Equipped With A Metal, Removable Retaining Disc That Measures 7/8” In Diameter And Is Just Shy Of 1/8” To Fit Into To The “T” Slot To Prevent Accidental Lifting When Feeding Your Stock Through. If Your Saw Does Not Have A “T” Slot, You Can Remove The Disc. The Steel Miter Bar Is Also Equipped With Spring Loaded, Adjustable Plungers On The Side Of The Bar. The Plungers Can Be Adjusted With The Provide Hex Key Wrench In Or Out To Provide You With The Ideal Fit..
The Head Is Mounted To A Solid Steel Miter Bar That Measure 18” In Length And Is .354” Thick By .730” Wide. Standard Miter Slots Are 3/4” X 3/8” With A 1/8” “T” Slot (Slight Variances From Brand To Brand) Running The Length On The Bottom Of The Slot. The Steel Miter Bar Is Equipped With A Metal, Removable Retaining Disc That Measures 7/8” In Diameter And Is Just Shy Of 1/8” To Fit Into To The “T” Slot To Prevent Accidental Lifting When Feeding Your Stock Through..
The .200” Thick, Adjustable, Solid Aluminum Head Is Machined With 13 Positive Stop Holes. 1 Hole Is At 90 Degrees While The 6 Holes On Both Sides Are At 22.5, 30, 45, 60, 67.5 And 90 Degrees. The Positive Stops Are Perfect For Many Woodworking Projects As They Are The Angles That Are Typically Used..
Features
- If you own a table saw and you need to make a crosscut at any angle then you know how valuable a miter gauge can be. You may also know that the miter gauge that came with your saw is not terribly accurate or durable. Not to mention that the fit in the miter slot may not be all that great as well. The Fulton Miter Gauge is a high quality, well thought out and economical solution to your table saw cross cutting needs.
- The .200 thick, adjustable, solid aluminum head is machined with 13 positive stop holes. 1 hole is at 90 degrees while the 6 holes on both sides are at 22.5, 30, 45, 60, 67.5 and 90 degrees. The positive stops are perfect for many woodworking projects as they are the angles that are typically used.
- To adjust the head you simply loosen the post knob handle, pull the spring loaded indexing pin outward, rotate the head to the desired position, release the pin and lock into place by tightening the post knob handle. The aluminum head has two x slots milled into it for mounting a miter fence if so desired. The slots are approximately 1-1/8 from the base of the miter gauge head.
- The head is mounted to a solid steel miter bar that measure 18 in length and is .354 thick by .730 wide. Standard miter slots are 3/4 x 3/8 with a 1/8 T slot (slight variances from brand to brand) running the length on the bottom of the slot. The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8 in diameter and is just shy of 1/8 to fit into to the T slot to prevent accidental lifting when feeding your stock through.
- The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8 in diameter and is just shy of 1/8 to fit into to the T slot to prevent accidental lifting when feeding your stock through. If your saw does not have a T slot, you can remove the disc. The steel miter bar is also equipped with spring loaded, adjustable plungers on the side of the bar. The plungers can be adjusted with the provide hex key wrench in or out to provide you with the ideal fit.
- See more on Amazon...
Brand: Fulton | Manufacturer: Fulton
Weight: 0.00 pounds
See On Amazon #7
Rockler 45 Degree Miter Sled for Table Saw - Miter Saw Sled Ensures Durability & Low-Friction Sliding - Table Saw Accessories Fits Standard 3/8" x 3/4" Miter Slot Fence Accessories
Asin: B0186IPNCM | Ean: 0785533187557, 0400000315935 | UPC: 400000315935, 785533187557
Adjusting Miter Track Fit: Use A 7/64" Hex Wrench (Not Included) To Advance The Nylon Set Screws In The Rockler 45 Degree Miter Sled Bar Until You Achieve A Smooth, No-Slop Fit In Your Saw’S Miter Track..
Easy To Use: The Table Saw Accessories Miter Can Be Easily Drilled To Add Extended Fences And Stops. Pre-Installed Adjustable Nylon Pins Provide A No-Slop Fit To The Miter Track..
Standard Slot: Through Slots In The Base Allow You To Securely Clamp Moldings At Table Level. This Table Saw Miter Sled Fits Standard 3/8" X 3/4" Miter Slots..
45 Degree Miter Sled: This Table Saw Sled System Gives You An Exact 45-Degree Cut Every Time. Our Table Saw Miter Is Great For Picture Frames Or Anytime Accurate Corner. Miters Cuts Are Needed..
Features
- Table Saw Miter Sled: This is the perfect table saw sled, no adjustments needed! Simply cut one piece on the leading face, one on the trailing face, and voila! Since both pieces reference off a perfect 90-degree angle, the miters will fit perfectly.
- 45 Degree Miter Sled: This table saw sled system gives you an exact 45-degree cut every time. Our table saw miter is great for picture frames or anytime accurate corner. Miters cuts are needed.
- Adjusting Miter Track Fit: Use a 7/64 hex wrench (not included) to advance the nylon set screws in the Rockler 45 degree miter sled bar until you achieve a smooth, no-slop fit in your saw s miter track.
- Standard Slot: Through slots in the base allow you to securely clamp moldings at table level. This table saw miter sled fits standard 3/8 x 3/4 miter slots.
- Easy To Use: The table saw accessories miter can be easily drilled to add extended fences and stops. Pre-installed adjustable nylon pins provide a no-slop fit to the miter track.
- See more on Amazon...
Brand: ROCKLER | Manufacturer: ROCKLER
Weight: 0.73 Pounds
See On Amazon #8
Peachtree Woodworking 19 inch Precision Aluminum Miter Bar Rail Runner w/Adjustable Spring Loaded Plungers DIY Table Saw Crosscut Sleds Jigs Works w/ 3/4 by 3/8 inch Miter Slots Mounting Hardware
Asin: B0B2G3H688 | Model: 4783 | PartNumber: 4783 | Ean: 0817918023072 | UPC: 817918023072
Not Only Is The Aluminum Miter Bar Adjustable, Its Easy To Mount! You Can Mount The Bar From The Top Of Your Sled, Jig Or Fixture Platform Or Base, Or You Can Mount It From The Bottom. There Are Threaded Holes Along The Length Of The Bar For Mounting The Bar Using 1/4 Inch By 20 Tpi Machine Screws (Included). There Are Also Counter Sunk Holes On The Bar To Mount The Bar Using #8 Wood Screws (Included)..
The Bar Is Approximately 19 Inches Long And Will Fit Into Standard (3/4 X 3/8 Inch) Miter T Slots And U-Shaped Miter Slots. Non-Standard Slots Found On Some Job Site Style Table Saws And Other Small Machinery Will Not Accept This Bar Due To The Non-Standard Slot Dimensions. We Recommend That You Measure Your Miter Slot Before Placing Your Order..
Once You Mount The Bars To Your Sled, Jig Or Fixture You Are Sure To Feel The Difference. This Is Especially True When You First Run The Bars Through Your Miter Slots. The Smooth Sliding Action Is Perfect For Crosscut Sleds, Miter Angle Jigs, Shop Made Coping Sleds And A Whole Lot More! Using Two Bars (Only One Is Included) For Even More Stability Works Exceptionally Well..
When Building Sleds, Jigs And Fixtures, One Of The Most Important Aspects Is To Achieve A Smooth Sliding Action Without Side To Side Play. The 19 Inch Precision Aluminum Miter Bar Does Both With Its Solid Aluminum Bar And 5 Adjustable Spring Loaded Plungers. The Plungers Can Be Adjusted With The Included Hex Key Wrench For Just The Right Fit..
Features
- Build your next table saw sled, router table jig or band saw fixture to operate with a smooth sliding action using our 19 inch Precision Aluminum Miter Bar! Attach the aluminum bar to most any type of sled, jig or fixture that is to be used with a 3/4 inch (19mm) by 3/8 inch (9mm) miter slot. Using our aluminum bar versus plastic or wood gives your sled, jig or fixture more strength and stability and it won t bend or warp.
- When building sleds, jigs and fixtures, one of the most important aspects is to achieve a smooth sliding action without side to side play. The 19 inch Precision Aluminum Miter Bar does both with its solid aluminum bar and 5 adjustable spring loaded plungers. The plungers can be adjusted with the included hex key wrench for just the right fit.
- Not only is the Aluminum Miter Bar adjustable, its easy to mount! You can mount the bar from the top of your sled, jig or fixture platform or base, or you can mount it from the bottom. There are threaded holes along the length of the bar for mounting the bar using 1/4 inch by 20 tpi machine screws (included). There are also counter sunk holes on the bar to mount the bar using #8 wood screws (included).
- Once you mount the bars to your sled, jig or fixture you are sure to feel the difference. This is especially true when you first run the bars through your miter slots. The smooth sliding action is perfect for crosscut sleds, miter angle jigs, shop made coping sleds and a whole lot more! Using two bars (only one is included) for even more stability works exceptionally well.
- The bar is approximately 19 inches long and will fit into standard (3/4 x 3/8 inch) miter t slots and u-shaped miter slots. Non-standard slots found on some job site style table saws and other small machinery will NOT accept this bar due to the non-standard slot dimensions. We recommend that you measure your miter slot before placing your order.
- See more on Amazon...
Brand: Peachtree Woodworking | Manufacturer: Peachtree Woodworking Supply Inc.
See On Amazon #9
POWERTEC 71391 Table Saw Precision Miter Gauge System w/ 27 Angle Stops and 3/4 x 3/8 T-Slotted Miter Bar w/Removable T-Slot Plate; Includes 24 x 3 Multi T Track Fence w/Scale, T-track Flip Stop
Asin: B07WR1V693 | Model: 71391 | PartNumber: 71391 | Ean: 0843441104193 | UPC: 843441104193
High Precision Miter Gauge: Features 27 Angle Indexing Stops With 1-Degree Step Spacing And Positive Stops At 0°, 10°, 22½°, 30°And 45°And Nine Others, Both Left And Right (Works In Standard 3/4” X 3/8” Miter Slot, With Or Without T-Slots, But Will Not Work With Smaller Saws Or Tool With 5/8” Miter Slots.).
Miter Saw Flip Stop: Delivers Exceptional Cut-Length Control, With A Toolless Locking Mechanism And Adjustable Settings To Quick Change To The Left Or Right Side Of The Blade.
Multi-Track Miter Fence: Smooth, Built-In Laser Engraved Measuring Scale, Extruded Aluminum Profile With A Universal Design That Accepts Accept 1/4"-20 Hex Bots, 1/4” T-Bolts And 5/16” T- Bolts, And T-Track Accessories.
Function: Cost Effective 3-Piece Set Designed To Give You Everything You Need To Produce Higher Precision Cuts (Including Cross Cutting) While With Quick And Accurate Project Results.
Features
- Includes: (1) table saw miter gauge, (1) multi-track miter fence, (1) t-track flip stop
- Function: cost effective 3-piece set designed to give you everything you need to produce higher precision cuts (including cross cutting) while with quick and accurate project results
- High precision miter gauge: features 27 angle indexing stops with 1-degree step spacing and positive stops at 0 , 10 , 22 , 30 and 45 and nine others, both left and right (Works in standard 3/4 x 3/8 miter slot, with or without t-slots, but will not work with smaller saws or tool with 5/8 miter slots.)
- Multi-track miter fence: smooth, built-in laser engraved measuring scale, extruded aluminum profile with a universal design that accepts accept 1/4-20 hex Bots, 1/4 t-bolts and 5/16 T- bolts, and T-track accessories
- Miter saw flip stop: delivers exceptional cut-length control, with a toolless locking mechanism and adjustable settings to quick change to the left or right side of the blade
- See more on Amazon...
Brand: POWERTEC | Manufacturer: POWERTEC
Dimensions: 25.00 x 4.62 x 3.37 inches | Weight: 5.75 Pounds
See On Amazon #10
VEVOR Precision Miter Gauge, 24" Aluminum Table Saw Miter Gauge w/ 60 Degree Angled Ends for Max. Stock Support and a Repetitive Cut Flip Stop, Miter Saw Fence w/Laser Marking Scale
Asin: B09MHDJZGZ | Model: 24 inch Miter Gauge | PartNumber: 24 inch Miter Gauge | Ean: 0840281596515 | UPC: 840281596515
Premium Sturdy Construction: This Woodworking Tool Is Made Of Aluminum Alloy, Ensuring Its Durability And Sturdiness. The Steel Miter Bar Is Equipped With A Removable Metal Retaining Disc To Prevent Accidental Lifting..
Wide Application: The Table Saw Miter Can Improve The Safety And Accuracy Of The Table Saw And The Router Table. It Also Can Be Used For Router Tables And Jointers. Miter Gauge Fence System Is Currently A Must-Have For Every Family..
Simple & Secure Operation: An Adjusting Screw And Guide Wheel Are Added In The Middle, Which Is More Convenient To Insert Into The Slot Hole And Fix The Seat. The Mitre Gauges Are Flat Without Burr, Secure, And Hands-Free..
Compatible Standeded Slot: Our Table Saw Sled Is Suitable For A Standard 0.75 X 0.38-Inch Miter Slot. Laser Marking Technology Is Friction-Resistance To Ensure Accuracy. It Is An Economical Solution For Your Table Saw Crosscutting Needs. The Adjustable, Solid Aluminum Head Is Machined With 11 Positive Stop Holes. 1 Hole Is At 90 Degrees While The 5 Holes On Both Sides Are At 10, 22.5, 30, 45, 60 And 90 Degrees..
Features
- Precise Angle Cutting: This table saw accessory is 0.04 inch / 1 mm high precision. Metric and imperial scale makes your work more convenient. Additional trim blocks raises working efficiency. Both sides 60 angle adjustable, ideal for crosscutting wood at a specific angle.
- Compatible Standeded Slot: Our table saw sled is suitable for a standard 0.75 x 0.38-inch miter slot. Laser marking technology is friction-resistance to ensure accuracy. It is an economical solution for your table saw crosscutting needs. The adjustable, solid aluminum head is machined with 11 positive stop holes. 1 hole is at 90 degrees while the 5 holes on both sides are at 10, 22.5, 30, 45, 60 and 90 degrees.
- Premium Sturdy Construction: This woodworking tool is made of aluminum alloy, ensuring its durability and sturdiness. The steel miter bar is equipped with a removable metal retaining disc to prevent accidental lifting.
- Simple & Secure Operation: An adjusting screw and guide wheel are added in the middle, which is more convenient to insert into the slot hole and fix the seat. The mitre gauges are flat without burr, secure, and hands-free.
- Wide Application: The table saw miter can improve the safety and accuracy of the table saw and the router table. It also can be used for router tables and jointers. Miter gauge fence system is currently a must-have for every family.
- See more on Amazon...
Brand: VEVOR | Manufacturer: VEVOR
Dimensions: 4.70 x 26.40 x 5.10 inches | Weight: 4.70 pounds
See On Amazon #11
PALS Precision Alignment and Locking System for Contractor Style Table Saw Alignment with 5/16 Inch Stud
Asin: B0036B4OFW | Model: 3154 | PartNumber: 3154 | Ean: 0810948015161 | UPC: 810948015161
The Smartly Made But Simple To Install Pals (Precision Alignment And Locking System) Offer The Perfect Solution To Getting Your Contractor Table Saw Properly Aligned Without All The Headaches. For Years, The Accepted Technique For Aligning Contractor Table Saws Was Normally Accomplished With A Hammer And A Piece Of Wood Along With A Bit Of Brute Force. Not Something We Should Be Doing To Our Woodworking Investment..
Pals Are Designed For Most Saws Where The Motor Hangs Out The Rear. Installing Them On “Hybrid” Saws May Prove Difficult, As Access To The Rear Housing (Trunnion) May Be Very Limited. Pals Are Available In 3 Stud Sizes, Which Will Fit Most Saws With 5/16”, 3/8”, Or 8Mm Bolts That Hold The Rear Trunnion In Position. Before Ordering, Please Measure The Bolt That Holds Your Rear Trunnions In Place. If It Does Not Match Any Of The Three Size Mentioned Here, The Pals Will Not Work With Your Saw..
The Main Component Of The System Are The “L” Brackets With Micro-Adjusting Screws. We Use To These To Make The Necessary Adjustments. The End Result Of Precision Alignment & Locking System (Pals) Installation Can Be A Perfectly Aligned Saw In Less Than 15 Minutes, And The Rear Trunnion Will Be “Locked In Position” To Prevent The Saw From Coming Out Of Alignment Again..
If You Own A Contractor Style Table Saw (Your Table Saw Motor Hanging Out The Back Of The Saw Denotes A Contractor Style Saw), You May Have Noticed That The Saw May Not Be Properly Aligned. Meaning, The Saw Blade Is Not Parallel With The Miter Slot On Our Table Saw Top. A Poorly Aligned Table Saw Is Not Only Frustrating To Use, But Also Is Dangerous To Operate..
Features
- Contractor table saw misalignment is common on a lot of saws. However, it is also one of the easiest issues to fix at a relatively low cost to do so. PALS allow you to make fine adjustments to the contractor saws rear trunnions, giving you the central to turn you saw into a perfectly aligned, precision cutting machine.
- If you own a contractor style table saw (your table saw motor hanging out the back of the saw denotes a contractor style saw), you may have noticed that the saw may not be properly aligned. Meaning, the saw blade is not parallel with the miter slot on our table saw top. A poorly aligned table saw is not only frustrating to use, but also is dangerous to operate.
- The smartly made but simple to install PALS (Precision Alignment and Locking System) offer the perfect solution to getting your contractor table saw properly aligned without all the headaches. For years, the accepted technique for aligning contractor table saws was normally accomplished with a hammer and a piece of wood along with a bit of brute force. Not something we should be doing to our woodworking investment.
- The main component of the system are the L brackets with micro-adjusting screws. We use to these to make the necessary adjustments. The end result of Precision Alignment & Locking System (PALS) installation can be a perfectly aligned saw in less than 15 minutes, and the rear trunnion will be locked in position to prevent the saw from coming out of alignment again.
- PALS are designed for most saws where the motor hangs out the rear. Installing them on hybrid saws may prove difficult, as access to the rear housing (trunnion) may be very limited. PALS are available in 3 stud sizes, which will fit most saws with 5/16 , 3/8 , or 8MM bolts that hold the rear trunnion in position. Before ordering, please measure the bolt that holds your rear trunnions in place. If it does not match any of the three size mentioned here, the PALS will not work with your saw.
- See more on Amazon...
Brand: Peachtree Woodworking Supply | Manufacturer: Peachtree Woodworking Supply Inc.
See On Amazon #12
Stanley 20-112 Clamping Miter Box
Asin: B00009OYGB | Model: 20-112 | PartNumber: 20-112
Ean: 7147905913042, 7294204756952, 7438455498418, 0043922391795, 8944467293013, 7241870690486, 6824917208410, 0076174201123
UPC: 076174201123, 043922391795
Manufacturer: Stanley.
Holes In Base For Fastening To A Workbench.
Limited Lifetime Warranty.
High-Impact Resistant Material.
Molded Lip On Base Edge For Easy Use Without Mounting.
An Ideal Miter Box For Precise And Versatile Cuts.
Country Of Manufacture: United States.
Features
- Power Tools and Accessories
- Country of manufacture: United States
- Manufacturer: Stanley
- An ideal miter box for precise and versatile cuts
- High-impact resistant material
- Molded lip on base edge for easy use without mounting
- Holes in base for fastening to a workbench
- Limited lifetime warranty
- See more on Amazon...
Brand: Stanley | Manufacturer: Stanley
Dimensions: 4.00 x 14.30 x 12.80 inches | Weight: 0.01 pounds
See On Amazon #13
Viking Mountain Tool Works 27 Position Precision Miter Gauge With 24inch (600MM) in Fence and Stop for Table Saw Band Saws, Router Tables Sanders
Asin: B0BGQMRYG2 | Model: 2701+2709 | PartNumber: 2701+2709 | Ean: 0810118500244 | UPC: 810118500244
The Fence Mounting Slots In The Protractor Head Are Designed To Work With Our 24 Inch Precision Aluminum Fence With Stop, Our 18 Inch Box Joint Fence, Or Most Commercially Available Fences Available From Other Manufactures..
The Fence And Stop Are Substantial And Well Made 24 Inch Nominal (23.6 Actual) By 3 Inch High For Great Work Support. The Curser On The Stop Allows For Precise Repeatable Measurements.
Made From Heavy Gage Aluminum And Steel. Includes Instructions For The Miter Gage As Well As The Two Fence Options.
The Miter Bar Is Designed For A Snug Fit In Machines With A 3/4" By 3/8 Inch Miter Slot (.740 To .760). It Will Also Work With A 3/4*3/8 Inverted T Slot..
Features
- With then Miter gage you get 27 Precision determined Stop Positions every 5 degrees from 0 to 60 degrees in both directions plus two additional at 22.5 degrees, useful for 8 sided Octagons.
- The miter bar is designed for a snug fit in Machines with a 3/4 by 3/8 inch miter slot (.740 to .760). It will also work with a 3/4*3/8 inverted T slot.
- The fence mounting slots in the protractor head are designed to work with our 24 inch precision aluminum fence with stop, our 18 inch Box Joint Fence, or most commercially available fences available from other manufactures.
- Made from heavy gage Aluminum and steel. Includes Instructions for the miter gage as well as the two fence options
- The Fence and Stop are substantial and well made 24 inch nominal (23.6 actual) by 3 inch high for great work support. The curser on the Stop allows for precise repeatable measurements
- See more on Amazon...
Brand: Viking Mountain Tool Works | Manufacturer: VMTW
See On Amazon #14
Peachtree Woodworking Supply Mounting Track Base Add On for the Tool Rest Sharpening Jig
Asin: B07VB9B2D3 | Ean: 0817918021610 | UPC: 817918021610
When You’Re Done With One Grit For Your Tool, Simply Loosen The Sharpening Jig Knob, Slide The Jig Out And Then Slide The Jig Back Into The Other Side! It Literally Takes Seconds To Switch From One Wheel To Another! This Makes The Tools Rest Sharpening Jig Even More Versatile Than It Already Is!.
If You Already Own The Jig, Then You Owe To Yourself To Get At Least One Mounting Track, If You Are Thinking About Purchasing The Tool Rest Sharpening Jig, Then We Encourage You To Consider Getting An Extra Mounting Track To Conveniently Work Both Wheels On Your Grinder. The Mounting Track Is Installed Using Four Wood Screws Which Are Included..
Made From The Exact Same Extruded Aluminum Material As The Original Mounting Track. The Mounting Track Not Only Allows Quick Switch Outs But It Also Allows You To Quickly Adjust The Jig Forward Or Backward Depending On What Type Of Tool You Are Sharpening..
Now, With An Extra Mounting Track Base You Can Have A Mounting Track For Each Of Your Two Wheels On Your Grinder! Once Both Mounting Tracks Have Been Installed, All You Have To Do Is Slide The Sharpening Jig Into One Side Or The Other And Start Sharpening!.
Features
- If you already own one of the Tool Rest Sharpening Jigs, then you know how versatile it is. Being able to accurately hone your tools can certainly be satisfying. Sometimes though it would be nice if we could have the ability to move the sharpening jig to the other side of the bench grinder to sharpen your tools with a different grit wheel.
- Now, with an extra Mounting Track Base you can have a mounting track for each of your two wheels on your grinder! Once both Mounting Tracks have been installed, all you have to do is slide the Sharpening Jig into one side or the other and start sharpening!
- When you re done with one grit for your tool, simply loosen the sharpening jig knob, slide the jig out and then slide the jig back into the other side! It literally takes seconds to switch from one wheel to another! This makes the Tools Rest Sharpening Jig even more versatile than it already is!
- Made from the exact same extruded aluminum material as the original Mounting Track. The Mounting Track not only allows quick switch outs but it also allows you to quickly adjust the jig forward or backward depending on what type of tool you are sharpening.
- If you already own the jig, then you owe to yourself to get at least one Mounting Track, if you are thinking about purchasing the Tool Rest Sharpening Jig, then we encourage you to consider getting an extra Mounting Track to conveniently work both wheels on your grinder. The Mounting Track is installed using four wood screws which are included.
- See more on Amazon...
Brand: Peachtree Woodworking Supply | Manufacturer: Peachtree Woodworking Supply Inc.
See On Amazon #15
Peachtree Woodworking Supply UHMW Precision Milled Bar 3/4" X 3/8" X 48" For Jigs, Fixtures or Miter Slots (size 3/4" x 3/8"). Slides with Ease. For Table Saws, Router Table and Bandsaws (1 UHMW Bars)
Asin: B01IU6U1UE | Ean: 7535001781816, 0795092653356, 7241871206334, 0810948011972, 7131405392735 | UPC: 810948011972, 795092653356
🇺🇸 Uhmw (Ultra High Molecular Weight) Polymer (Plastic) Is A Linear Polyethylene Material With A Molecular Weight In The Range Of 3,000,000 To 6,000,000. Uhmw Is 10 Times Heavier Than Regular High Density Polyethylene Making It Extremely Durable For Constant Repetitive Use..
🇺🇸 Use This Uhmw To Make Jigs And Fixtures For Your Table Saw , Router Table, Etc. Use The 3/4" X 3/8" Plastic Strips To Make Sliding Table Jigs For Your Table Saw, Band Saw Or Router Table. Length Of Bar May Vary Slightly Made In The Usa!.
🇺🇸 Ideal For Sleds Where Repetitive Sliding Happens Regularly. Its Also Very Slick In Comparison To Wood And Other Plastics. Even Though Its "Slick", It Does Not Leave Behind Any Residue Which Means No Clean Up After Use. We All Know How Residue Left On A Table Saw Can Be Rather Irritating And Harder To Remove..
🇺🇸 Even Though Its "Slick", It Does Not Leave Behind Any Residue Which Means No Clean Up After Use. We All Know How Residue Left On A Table Saw Can Be Rather Irritating And Even Harder To Remove..
Features
- The idea behind using UHMW material for making jigs & fixtures is that the material stands up to friction better than wood and lower quality or lower density plastics. This makes it ideal for sleds where repetitive sliding happens regularly. Its also very slick in comparison to wood and other plastics. Even though its "slick", it does NOT leave behind any residue which means no clean up after use. We all know how residue left on a table saw can be rather irritating and even harder to remove
- Even though its slick, it does NOT leave behind any residue which means no clean up after use. We all know how residue left on a table saw can be rather irritating and even harder to remove.
- UHMW (Ultra High Molecular Weight) Polymer (plastic) is a linear polyethylene material with a molecular weight in the range of 3,000,000 to 6,000,000. UHMW is 10 times heavier than regular high density polyethylene making it extremely durable for constant repetitive use.
- Ideal for sleds where repetitive sliding happens regularly. Its also very slick in comparison to wood and other plastics. Even though its slick, it does NOT leave behind any residue which means no clean up after use. We all know how residue left on a table saw can be rather irritating and harder to remove.
- Use this UHMW to make jigs and fixtures for your table saw , router table, etc. Use the 3/4 x 3/8 plastic strips to make sliding table jigs for your table saw, band saw or router table. Length of bar may vary slightly MADE IN THE USA!
- See more on Amazon...
Brand: Peachtree Woodworking Supply | Manufacturer: Peachtree Woodworking
Weight: 0.01 pounds
See On Amazon #16
Peachtree Woodworking Supply Anodized Aluminum Miter T Track w/T-Bar Rail for Jigs Fixtures Sleds Router Tables and General Woodworking 32 inch MADE IN THE USA
Asin: B000KUZMOE | Model: 1035 | PartNumber: 1035 | Ean: 0810948012269 | UPC: 810948012269
The “T” Shape On The Miter Track Also Accepts The T-Bar. The T-Bar Has Been Designed To Fit Neatly Into The Miter Track Profile For Use With Jigs, Fixtures Or Sleds. The T-Bar Is Made From A Solid Piece Of Extruded Aluminum And Can Be Cut Into Sections And Drilled As Needed. Typical Uses For The T-Bar Are Fixtures Like Featherboards Where The Featherboard Needs To Be Kept Stationary To Apply Consistent Pressure. The T-Bar Also Works Great For Sleds And Other Sliding Fixtures..
When We Decided To Start Manufacturing Aluminum Tracks Many Years Ago (Well Over 20 Years), We Thought That It Was Very Important To Do Our Best To Keep The Manufacturing Process Here In The United States. We Are Proud To Say That Even After 20 Years, We Manufacture All Of Our Anodized Aluminum Track (Including This Miter T Track) Here In The Usa. This Helps Our Customers Know That Not Only Are They Supporting The Economy, But Also Receiving A High Quality Product..
Miter T Track Is Often Used In Woodworking Applications But Can Be Used Most Anywhere Throughout A Workshop Setting. It Is The Ideal Solution For Router Tables In Need Of A Miter Slot For Miter Gauges. The ¾” Wide Slot Accommodates Most Miter Gauges Which Makes It Super Handy For Any Workshop. Many Woodworkers And Professionals Alike Build Jigs Or Sleds With Uhmw Bars On The Bottom That Fit Right Into This Miter Track..
The Miter T Track Has A “T” Shape To It So That It Can Accept The Discs On The Ends Of Many Miter Gauges. This Essentially Means That Your ¾” X 3/8” Bar On Your Miter Gauge Will Fit Neatly Into This Track Even With The Disc On The End. Of Course You Don’T Have To Have A Bar With The Disc On The End. Wether You’Re Making A Table Top For Your Router, Your Band Saw Or Simply Building A Sled, A Standard ¾” X 3/8” Thick Bar Will Do The Trick!.
Features
- When building sleds or fixtures, workshop tables, router table tops or any type of jig or fixture that helps hold stock in place or helps feeding stock through a cutter, miter t track will help make it so much easier. Miter T Track does this by allowing devices like miter gauges to effortlessly slide through the track for cutting applications and it can also accept fixtures with the proper hardware like featherboards to keep your stock firmly against a fence.
- The Miter T Track has a T shape to it so that it can accept the discs on the ends of many miter gauges. This essentially means that your x 3/8 bar on your miter gauge will fit neatly into this track even with the disc on the end. Of course you don t have to have a bar with the disc on the end. Wether you re making a table top for your router, your band saw or simply building a sled, a standard x 3/8 thick bar will do the trick!
- The T shape on the Miter Track also accepts the T-bar. The T-bar has been designed to fit neatly into the miter track profile for use with jigs, fixtures or sleds. The T-bar is made from a solid piece of extruded aluminum and can be cut into sections and drilled as needed. Typical uses for the T-bar are fixtures like featherboards where the featherboard needs to be kept stationary to apply consistent pressure. The T-bar also works great for sleds and other sliding fixtures.
- Miter T Track is often used in woodworking applications but can be used most anywhere throughout a workshop setting. It is the ideal solution for router tables in need of a miter slot for miter gauges. The wide slot accommodates most miter gauges which makes it super handy for any workshop. Many woodworkers and professionals alike build jigs or sleds with UHMW bars on the bottom that fit right into this miter track.
- When we decided to start manufacturing aluminum tracks many years ago (well over 20 years), we thought that it was very important to do our best to keep the manufacturing process here in the United States. We are proud to say that even after 20 years, we manufacture all of our anodized aluminum track (including this Miter T Track) here in the USA. This helps our customers know that not only are they supporting the economy, but also receiving a high quality product.
- See more on Amazon...
Brand: Peachtree Woodworking Supply | Manufacturer: Peachtree Woodworking Supply Inc.
See On Amazon #17
Peachtree Woodworking Supply Cam Action T-Track Quick Release Hold Down Clamp for Jigs, Fixtures & Shop Fences. Ideal for Router and Drill Press Table Fences (1, 3/8")
Asin: B000KV53WY | Ean: 0810948012177 | UPC: 810948012177
The Clamp Body Is Made Out Of Aluminum, Measures Approximately 1-1/2” Long And Each Clamp Has A Standard 3” Long Hex Head Bolt That Works With Most Standard Sizes Of T-Track (Depending On Which Size Cam Action Clamp You Purchase). Be Sure To Get The Correct Size For Your Needs. Typically That Means You Should Check To See What Size Slot Or Track You Would Like To Use The Clamps In..
For Instance, If You Have A Slot Requiring A T-Bolt, You Can Switch Out The ¼” Hex Head Bolt With A ¼” T-Bolt. Each Cam Can Exert Up To 400 Pounds Of Clamp Pressure Depending On How You Set It..
The Cam Action Clamps Are Available In ¼” 5/16” And 3/8” Hex Head Bolt Sizes. Another Nice Feature Of The Cam Action Clamps Is That You Can Swap The Bolts Out For Different Situations..
Our Exclusive Cam Clamps Will Solve Your Problem And Provide You With A Quick Release Clamping System For All Of Your Jigs, Fixtures And Some Fences That Rely On A Track System. Having A Cam Clamp On Your Router Table Fence Makes Is So Much Easier To Make Quick Adjustments And Quickly Lock The Fence In Place..
Features
- Finally, a quick release clamping system for jigs, fixtures and fences. Spending a lot of time tightening and loosening knobs on your jigs and fixtures? Or maybe your are constantly rotating knobs on your router table or drill press fences.
- Our exclusive cam clamps will solve your problem and provide you with a quick release clamping system for all of your jigs, fixtures and some fences that rely on a track system. Having a cam clamp on your router table fence makes is so much easier to make quick adjustments and quickly lock the fence in place.
- The clamp body is made out of aluminum, measures approximately 1-1/2 long and each clamp has a standard 3 long hex head bolt that works with most standard sizes of t-track (depending on which size Cam Action Clamp you purchase). Be sure to get the correct size for your needs. Typically that means you should check to see what size slot or track you would like to use the clamps in.
- The Cam Action Clamps are available in 5/16 and 3/8 hex head bolt sizes. Another nice feature of the Cam Action Clamps is that you can swap the bolts out for different situations.
- For instance, if you have a slot requiring a T-bolt, you can switch out the hex head bolt with a T-bolt. Each cam can exert up to 400 pounds of clamp pressure depending on how you set it.
- See more on Amazon...
Brand: Peachtree Woodworking Supply | Manufacturer: Peachtree Woodworking Supply Inc.
See On Amazon #18
Peachtree Woodworking Supply A-LINE-IT DELUXE Machinery/Tool Alignment System w/ 22 Interchangeable Tips, 11 inch Long Anodized Aluminum Bar, Dial Indicator, Precision Steel Pin and Arbor Run-Out Kit
Asin: B0036AYXQS | Model: 3158 | PartNumber: 3158 | Ean: 0810948015727 | UPC: 810948015727
One Of The Reasons You’Ll Appreciate This System Is The Self-Adjusting “Smart Bar” That Will Stay Tight In A Miter Slot That Isn’T The Same Size Along It’S Slot Length. You Only Need To Adjust The Spring Plungers Once, And After That, Its A Perfect Fit In The Miter Slot. This Makes The Measuring Process Much More Efficient Since You Don’T Need To Keep Shimming Or Adjusting The Miter Bar For A Snug Fit..
The A-Line-It Deluxe Includes The Following: Dial Indicator In .001” Increments, 22 Assorted And Interchangeable Dial Indicator Tips, 11” Long Bar With 12 Adjustment Holes, Smart Miter Bar With Spring Loaded Adjustable Plungers, Threaded 1/2” Diameter Steel Drill Press Chuck Pin, The Exclusive Arbor Nut Run-Out Kit, Planer Bar (For Checking Run-Out On Planers With Knife Style Cutter Heads) And Detailed Instructions..
Another Thing You Will Appreciate Is That With The A-Line-It Deluxe, You Get Everything You’Ll Need To Thoroughly Check Your Machines In One Package. The Spring And Nut Assembly, As An Example, Makes The A-Line-It Deluxe The Only Tool In The Us That Will Allow You To Determine Whether The Run-Out In The Saw Blade Is Caused By The Blade, The Arbor, Or A Combination Of Both. Being Able To Determine This Is Vitally Important To Achieve The Best Running Table Saw Possible..
One Of The Most Common Machines That Need To Be Aligned And Maintained Is Our Table Saws. As We Use Them, The Fence And Saw Blade Amongst Other Parts Tend To Slightly Shift Over Time. The A-Line-It Deluxe Has All The Necessary Pieces To The Puzzle To Help You Identify What Needs To Be Addressed In Order To Get Your Table Saw In Tip Top Shape Again. You Can Easily Identify, Saw Blade Straightness, Fence Run-Out, Arbor Run-Out And Flange Run-Out..
Features
- Aligning your workshop machinery can be very frustrating. Sometimes a tape measure, ruler and a firm fist bump just won t cut it. If you desire to have your machinery working at optimal levels then look no further than the A-LINE-IT DELUXE Machinery and Tool Alignment System. Get the precision you want out of your machinery without having to break the bank. After all, much like a car, your machinery is an investment that needs to be tuned up and maintained.
- One of the most common machines that need to be aligned and maintained is our table saws. As we use them, the fence and saw blade amongst other parts tend to slightly shift over time. The A-LINE-IT DELUXE has all the necessary pieces to the puzzle to help you identify what needs to be addressed in order to get your table saw in tip top shape again. You can easily identify, saw blade straightness, fence run-out, arbor run-out and flange run-out.
- One of the reasons you ll appreciate this system is the self-adjusting Smart Bar that will stay tight in a miter slot that isn t the same size along it s slot length. You only need to adjust the spring plungers once, and after that, its a perfect fit in the miter slot. This makes the measuring process much more efficient since you don t need to keep shimming or adjusting the miter bar for a snug fit.
- Another thing you will appreciate is that with the A-LINE-IT DELUXE, you get everything you ll need to thoroughly check your machines in one package. The spring and nut assembly, as an example, makes the A-LINE-IT DELUXE the only tool in the US that will allow you to determine whether the run-out in the saw blade is caused by the blade, the arbor, or a combination of both. Being able to determine this is vitally important to achieve the best running table saw possible.
- The A-LINE-IT DELUXE includes the following: Dial Indicator in .001 increments, 22 assorted and interchangeable dial indicator tips, 11 long bar with 12 adjustment holes, smart miter bar with spring loaded adjustable plungers, threaded 1/2 diameter steel drill press chuck pin, the exclusive arbor nut run-out kit, planer bar (for checking run-out on planers with knife style cutter heads) and detailed instructions.
- See more on Amazon...
Brand: Peachtree Woodworking Supply | Manufacturer: In-Line Industries
Dimensions: 2.90 x 9.70 x 8.30 Inches
See On Amazon #19
Peachtree Woodworking Supply The Original Dubby Cut-Off Cross Cut Sled for Cutting Precise Accurate Miters with a Table Saw (Left Side and Right Side are Included)
Asin: B09X7H967R | Ean: 0817918023225 | UPC: 817918023225
Working With Angles The Dubby Angle Scale Is The Simplest, Most Accurate And Easiest To Read Scale Available. Being About 15-20 Times More Accurate Than The Average Miter Gauge, The Scale Has Pre-Determined Lines For Any Shape (From 4 To 16 Sides) You Want To Cut. This Means No Calculations, No Hassles, And Best Of All, No Test Cuts For Perfect Results.
Will The Dubby Fit Your Saw? The Dubby Sled Is Compatible With Most Cabinet And Contractor Table Saws. However, Your Table Saw Should Fall Within The Following Specs For A Proper Fit. The Miter Slot Should Be A ¾” Wide X 3/8” Deep Slot. Your Saw Must Measure At Least 27” From The Front Of The Saw To The Back. The Miter Slot Must Be 4” To 5 ¾” From The Installed Table Saw Blade. Please Note: That The Dubby Will Not Work On Most Jobsite Style Table Saws. Please Measure Your Saw Before Ordering..
Working With Small Pieces- No Miter Gauge On The Market Can Offer You The Margin Of Safety Provided By The Dubby Sled. The Versatile Hold-Down Clamp Included With Every Dubby Will Give You An Extremely Safe Way To Cut Small Pieces, And Will Easily Pivot Out Of The Way When You Don’T Need It. With 35Lbs. Of Hold Down Pressure, The Clamp Will Hold Small Pieces All The While Keeping Your Hands And Fingers Out Of Harms Way..
Working With Large Panels The Dubby Has The Capacity To Crosscut Panels Up To 24″ Wide X 52″ Long, And Allows You To Do Them Safely. Since The Panels Don’T Make Contact With The Table Saw Top, “Walking” Of The Material Is Virtually Eliminated. This Will Allow You To Cut Perfectly Square Panels For Your Furniture And Cabinet Making Projects Quickly, Easily And Accurately..
Features
- THE ORIGINAL DUBBY SLED From standard 4 sided panel cutting to the absolutely stunning heptagon frame you will be completely accurate with the angles on your mitered projects with the Dubby Sled. The Dubby will allow you to make perfect cuts the first time you do them and keep your creative juices flowing with idea after idea. It is ideal for making frames but it also works very well for the cutting of tiny pieces while keeping your fingers out of harms way.
- WORKING WITH LARGE PANELS The Dubby has the capacity to crosscut panels up to 24 wide x 52 long, and allows you to do them safely. Since the panels don t make contact with the table saw top, walking of the material is virtually eliminated. This will allow you to cut perfectly square panels for your furniture and cabinet making projects quickly, easily and accurately.
- WORKING WITH ANGLES The Dubby angle scale is the simplest, most accurate and easiest to read scale available. Being about 15-20 times more accurate than the average miter gauge, the scale has pre-determined lines for any shape (from 4 to 16 sides) you want to cut. This means no calculations, no hassles, and best of all, no test cuts for perfect results
- WORKING WITH SMALL PIECES- No miter gauge on the market can offer you the margin of safety provided by the Dubby Sled. The versatile hold-down clamp included with every Dubby will give you an extremely safe way to cut small pieces, and will easily pivot out of the way when you don t need it. With 35lbs. of hold down pressure, the clamp will hold small pieces all the while keeping your hands and fingers out of harms way.
- WILL THE DUBBY FIT YOUR SAW? The Dubby sled is compatible with most cabinet and contractor table saws. However, your table saw should fall within the following specs for a proper fit. The Miter Slot should be a wide x 3/8 deep slot. Your saw must measure at least 27 from the front of the saw to the back. The miter slot must be 4 to 5 from the installed table saw blade. PLEASE NOTE: that the Dubby WILL NOT work on most JOBSITE style table saws. Please measure your saw before ordering.
- See more on Amazon...
Brand: Peachtree Woodworking Supply | Manufacturer: Peachtree Woodworking Supply Inc.
Weight: 20.00 pounds
See On Amazon #20
Precision Miter Gauge with a Standard Slot (3/4 x 3/8 ), Table Saw Miter Gauge High Accuracy Miter Saw Protractor with 27 Angle Stops, Great Woodworking Tool Table Saw Accessories
Asin: B0B515JGZR
Refined In The Details: Overall Lightweight Design, Durable Aluminum Alloy Construction, Comfortable Grip Handle, Can Match Universal Fence Mounting Bracket, Easy-To-Operate Swivel Locking Mechanism, Can Be Miter Gage With T-Slot And Non-T-Slot The Dismantling Plate Used In Conjunction With The Slot, And The Adjustable Expansion Disc, Eliminate All Side Play Of The Rod For A Perfect Fit..
Universal Design: Fits Most Contractor Styles, Full-Size Saws Or Tools With Standard Miter Slots (3/4"W X 3/8"D), With Or Without T-Slots, Matches Most Brands Table Saws, Band Saws, Router Tables, Disks And Belt Sanders. Please Note: Not For Use With Small Saws Or Tools With 5/8" Miter Grooves..
Precise Accuracy: The Angle Guide Has A Total Of 27 Locking Stops In 5-Degree Increments Over The Entire 180-Degree Range, Allowing A Maximum Of Plus Or Minus 60-Degree Bevels. A 0-Degree Slot In The Middle, 13 Slots On Each Side (5°, 10°, 15°, 20°, 22.5°, 25°, 30°, 35°, 40°, 45°, 50°, 55°, 60° )..
Simple To Operate: To Adjust The Angle Disc Angle Setting, You Simply Loosen The Knob Handle, Pull The Indexing Pin Outward, Rotate The Angle Disc To The Desired Scale, Insert The Locking Pin And Lock In Place By Tightening The Knob Handle..
Features
- High-Performance Woodworking Angle Tool: Miter Gage with Standard Miter Slot (3/4 x 3/8 ) and 1/8 T Slot Miter Rails, mounted on table saw (band saws and other applications) and then guide the miter gauge parallel to the blade for high precision miter and cross cuts.
- Simple to operate: To adjust the angle disc angle setting, you simply loosen the knob handle, pull the indexing pin outward, rotate the angle disc to the desired scale, insert the locking pin and lock in place by tightening the knob handle.
- Refined in the details: Overall lightweight design, durable aluminum alloy construction, comfortable grip handle, can match universal fence mounting bracket, easy-to-operate swivel locking mechanism, can be miter gage with T-slot and non-T-slot The dismantling plate used in conjunction with the slot, and the adjustable expansion disc, eliminate all side play of the rod for a perfect fit.
- Precise Accuracy: The angle guide has a total of 27 locking stops in 5-degree increments over the entire 180-degree range, allowing a maximum of plus or minus 60-degree bevels. A 0-degree slot in the middle, 13 slots on each side (5 , 10 , 15 , 20 , 22.5 , 25 , 30 , 35 , 40 , 45 , 50 , 55 , 60 ).
- Universal Design: Fits most contractor styles, full-size saws or tools with standard miter slots (3/4W x 3/8D), with or without T-slots, matches most brands table saws, band saws, router tables, disks and belt sanders. PLEASE NOTE: Not for use with small saws or tools with 5/8 miter grooves.
- See more on Amazon...
Brand: Kingson | Manufacturer: Kingson
See On Amazon
Looking For Something Else?
Search