Peachtree Woodworking Supply 2 Pack of 4 Way Pressure Clamps For Clamping Panels - Using Pressure From All Four Directions. For Woodworkers, Cabinet and Furniture Makers (2 four way pressure clamps)
Asin: B073QSF8JR | Model: 666 | PartNumber: 666
As an Amazon Associate we earn a fee from qualifying purchases when you follow a link to Amazon from this page. We rank the products, but the links to Amazon are promotional.Build Any Length Clamp With The Durable Plastic Bars With 4 Notches For Maximum Adjustability To Handle A Variety Of Stock Widths. Clamp Can Be Used For Boards Up To 6 Inches In Thickness By Simply Adjusting The Clamp Width Capacity With The Appropriate Number Of Notches. Turn The Handle Clockwise To Tighten The Clamp And Turn The Handle Counter Clockwise To Release Pressure. The 4 Way Pressure Clamp Is Equipped With Side Pressure Pads To Prevent Damaging Your Stock..
This Clamp Package Comes With Two Full 4 Way Pressure Clamp Assemblies. Includes: 2 Each Rotating Handle Assemblies, 2 Each Tailstock Assemblies, 4 Each Side Pressure Pads And 12 Each 4 Notch Bars. Together, This Setup Will Allow You To Create Two 4 Way Pressure Clamps. More Than One Clamp Is Generally Recommended For Any Project Over 12” In Length. Wood Is Required For Setting Up The Clamp. Wood Is Not Included..
Now You Can Confidently Glue Up Wide Boards, Shelving, Table Tops, And More Up To 6” Thick. To Setup The Clamps Simply Attach The Clamp To Any Length 2 X 2’S (2” X 4” Ripped In Half) With The The Wood Screws That Are Provided, Apply Wood Glue To Your Project, Set The Clamps On To Your Panel Boards And Turn Handle To Tighten The Clamp On All Four Sides. We Recommend That You Place A 4 Way Pressure Clamp Every 12” To 18” For Best Results..
Let’S Make Racked Panel Glue Ups A Thing Of The Past! The Uniquely Designed 4 Way Pressure Solves This Age Old Issue By Applying Pressure To All Four Sides Of Your Panel Glue Up. With A Simple Turn Of The Rotating Clamp Handle, All Four Sides Of The Clamp Will Draw Inward At The Same Time. This Provides Equal Pressure On To Your Panel And Prevents Bowing, Buckling, Or Racked Panels..
Features
- Clamping panels can certainly be a challenge. Especially when we try to use everyday pipe clamps or bar clamps. While these types of clamps work fairly well on certain glue up projects, the one thing they don t do at all is apply pressure from the top and bottom of the panels during glue up. In fact, with all the pressure being applied on both sides, bar and pipe clamps will almost certainly bow, buckle or rack your panel glue up project.
- Let s make racked panel glue ups a thing of the past! The uniquely designed 4 way pressure solves this age old issue by applying pressure to all four sides of your panel glue up. With a simple turn of the rotating clamp handle, all four sides of the clamp will draw inward at the same time. This provides equal pressure on to your panel and prevents bowing, buckling, or racked panels.
- Build any length clamp with the durable plastic bars with 4 notches for maximum adjustability to handle a variety of stock widths. Clamp can be used for boards up to 6 inches in thickness by simply adjusting the clamp width capacity with the appropriate number of notches. Turn the handle clockwise to tighten the clamp and turn the handle counter clockwise to release pressure. The 4 way pressure clamp is equipped with side pressure pads to prevent damaging your stock.
- Now you can confidently glue up wide boards, shelving, table tops, and more up to 6 thick. To setup the clamps simply attach the clamp to any length 2 x 2 s (2 x 4 ripped in half) with the the wood screws that are provided, apply wood glue to your project, set the clamps on to your panel boards and turn handle to tighten the clamp on all four sides. We recommend that you place a 4 way pressure clamp every 12 to 18 for best results.
- This clamp package comes with two full 4 way pressure clamp assemblies. Includes: 2 each rotating handle assemblies, 2 each tailstock assemblies, 4 each side pressure pads and 12 each 4 notch bars. Together, this setup will allow you to create two 4 way pressure clamps. More than one clamp is generally recommended for any project over 12 in length. Wood is required for setting up the clamp. Wood is NOT included.
- See more on Amazon...
Brand: Peachtree Woodworking Supply | Manufacturer: Peachtree Woodworking Supply Inc..
Weight: 9.15 Pounds
See On Amazon Similar To Peachtree Woodworking Supply 2 Pack
#1
ODIE'S Oil Starter Kit with Odies Oil 9 Ounce Jar 10 Non-Woven White Applicator Pads 2 Terry Cloth Buffing Towels and 10 Wooden Stirring Sticks
Asin: B0B9HMGNN5 | Model: 22109 | PartNumber: 22109 | Ean: 0817918023287 | UPC: 817918023287
This Convenient Starter Pack Includes 10 White Non-Woven Applicator Pads For Applying Odie’S Oil To Your Project. The White Non-Woven Pads Are Perfect For This Since They Are A Very High Grit, Smooth Abrasive That Won’T Scratch Or Leave Unsightly Marks Behind. The Pads Help You Properly Work The Odie’S Oil Into Your Workpiece..
10 Stirring Sticks Are Also Included With This Pack For Stirring The Odie’S Oil. The Sticks Can Also Be Used To Dab More Odie’S Oil On To Your Project Or The Applicator Pad. Each Stick Measures Approximately 6 Inches Long And Is Made From Wood..
The 2 Terry Cloth Towels Are The Ideal Towels To Use For Buffing Off Your Odie’S Oil Once It Is Dry. Simply Fold The Towel Into A Comfortable Size For You And Your Project And Buff Off The Odie’S Oil Going With The Grain Of Your Wood For An Exceptional Sheen And Luster..
Odie's Oil Is Great For All Species Of Wood, Exotic And Domestic. Formulated To Work On Even The Oiliest Of Woods. Your Surface With Odie's Oil Applied Will Actually Get Better With Age, Becoming More Durable And More Beautiful As Time Goes On. It Contains Natural Uv Inhibitors-Sunscreen For Your Wood!.
Features
- We all want our finished woodworking projects to look their absolute best when finished. The hard part shouldn t be the application process, nor should it be the choosing of what to apply to your project. Introducing Odie's Oil, the food safe, solvent free, non-toxic wood finish and wood stabilizer. Odie s Oil is easy to use and it waterproofs and leaves a wonderful lustrous sheen in one coat. It is also the perfect finish for leather, concrete, plastic, vinyl and metal.
- Odie's Oil is great for all species of wood, exotic and domestic. Formulated to work on even the oiliest of woods. Your surface with Odie's Oil applied will actually get better with age, becoming more durable and more beautiful as time goes on. It contains natural UV inhibitors-sunscreen for your wood!
- This convenient starter pack includes 10 white non-woven applicator pads for applying Odie s Oil to your project. The white non-woven pads are perfect for this since they are a very high grit, smooth abrasive that won t scratch or leave unsightly marks behind. The pads help you properly work the Odie s Oil into your workpiece.
- The 2 terry cloth towels are the ideal towels to use for buffing off your Odie s Oil once it is dry. Simply fold the towel into a comfortable size for you and your project and buff off the Odie s Oil going with the grain of your wood for an exceptional sheen and luster.
- 10 stirring sticks are also included with this pack for stirring the Odie s Oil. The sticks can also be used to dab more Odie s Oil on to your project or the applicator pad. Each stick measures approximately 6 inches long and is made from wood.
- See more on Amazon...
Brand: ODIE'S | Manufacturer: Odie's
See On Amazon #2
Peachtree Woodworking Supply 4 inch to 2-1/2 inch Reducer with 4 inch Flexible Cuff Rubber Coupler Fitting and Stainless Steel Hose Clamps with Turn Key Thumb Screw to Tighten & Loosen
Asin: B0C598B129 | Ean: 0817918023942 | UPC: 817918023942
Two Stainless Steel Hose Clamps Help Provide A Tight Seal On The 4 Inch End And Keep The Reducer From Falling Out. These Clamps Fit Neatly Into The Slots Around The Coupler So There Is No Slipping When Tightened. No More Busting Your Knuckles. Each Clamp Is Equipped With A Blue Turn Key Mechanism To Make Tightening And Loosening The Clamp Super Easy..
Made From High Quality Abs Plastic For Extended Periods Of Use, The Reducer Fitting Will Withstand The Constant Friction And Debris Flow Of Woodworking Dust Collectors. The Reducer Measures: Nominal 4” End Is 3-61/64” Od And 3-41/64” Id; 2-1/2” Nominal Od End Measures 2-15/32” Od And 2-9/32” Id. Dimensions May Slightly Vary Due To Slight Variations In The Manufacturing Process..
The Rigid Rubber Coupler Seals Tightly Around The Reducer For Excellent Airflow. Easy To Install And Easy To Remove. As With Most All Other Dust Collection Fittings, It’S Always A Good Idea To Have Extra On Hand For When You Need It. It’S Always Better To Have It And Not Need It Than It Is To Need It And Not Have It..
Most Wet/Dry Vacuum Hoses Will Plug Directly Into The Smaller End Of This Fitting Making It A Super Value For Most Professional And Us Weekend Warrior Type Woodworkers. There Are Some Vacuum Units That Use Different Size Hoses And Hose Adaptors So Please Be Sure To Measure Your Hose And Machine Ports Before Making A Purchasing Decision..
Features
- Reducing a 4 inch dust port on your machinery has never been easier! With our 4 inch to 2-1/2 inch hose reducer fitting and rubber coupler you can connect a 2-1/2 inch hose directly to a 4 port on machines like band saws, table saws, large planers and more. This convenient combo pack is designed to accept most standard size 4 inch dust collection fittings such as Y s, T s, Elbows, Blast gates, Dust ports and other standard size 4 inch dust collection fittings.
- Most wet/dry vacuum hoses will plug directly into the smaller end of this fitting making it a super value for most professional and us weekend warrior type woodworkers. There are some vacuum units that use different size hoses and hose adaptors so please be sure to measure your hose and machine ports before making a purchasing decision.
- Two stainless steel hose clamps help provide a tight seal on the 4 inch end and keep the reducer from falling out. These clamps fit neatly into the slots around the coupler so there is no slipping when tightened. No more busting your knuckles. Each clamp is equipped with a blue turn key mechanism to make tightening and loosening the clamp super easy.
- The rigid rubber coupler seals tightly around the reducer for excellent airflow. Easy to install and easy to remove. As with most all other dust collection fittings, it s always a good idea to have extra on hand for when you need it. It s always better to have it and not need it than it is to need it and not have it.
- Made from high quality ABS plastic for extended periods of use, the reducer fitting will withstand the constant friction and debris flow of woodworking dust collectors. The reducer measures: Nominal 4 end is 3-61/64 OD and 3-41/64 ID; 2-1/2 nominal OD end measures 2-15/32 OD and 2-9/32 ID. Dimensions may slightly vary due to slight variations in the manufacturing process.
- See more on Amazon...
Brand: Peachtree Woodworking Supply | Manufacturer: Peachtree Woodworking Supply Inc.
Weight: 1.00 Pounds
See On Amazon #3
Peachtree Woodworking Supply Cleaning Eraser Stick Small 1-1/2" x 1-1/2" x 7-7/8" Made from Natural Rubber for Removing Dust and Build up from Abrasive Belts Sanding Discs Drum Sanders Grip Tape
Asin: B000H69U7G | Model: 187 | PartNumber: 187 | Ean: 0810948010838 | UPC: 810948010838
It Works Almost Like An Old Fashioned Pencil Eraser. As You Rub Or Slide The Stick Across An Abrasive Surface The Stick Quickly Loosens And Removes Foreign Materials. Your Abrasives Will Be Brought Back To Life To Continue Sanding. If You Have Power Sanders Like Belt Sanders You Can Simply Hold The Stick Up Against The Sanding Belt While The Power Is On And Watch The Belt Be Cleaned Right Before Your Eyes!.
The Natural Rubber Cleaning Eraser Stick Also Works Exceptionally Well On Skateboard Grip Surfaces Which Tend To Get Dirty Rather Quickly. Once Clean, The Skateboard Surface Is Almost As Good As New And Keeps Its Grip A Whole Lot Longer. Similar To Skateboard Grip Surfaces, Abrasive Or Grip Tape That’S Used On Floor Areas That Can Get Slippery Can Be Easily Cleaned Using The Eraser Stick..
Clean Various Items Around The House, Workshop Or In The Garage. The Rubber Construction Of The Stick Works Best On Belt Sanders To Allow Your Belts To Cut Faster And Last Longer All The While It Can Also Be Used On Disc Sanders, Drum Sanders, Rubber Bottom Shoes (Not Plastic), Skateboard Grip Tape, Grip Tape And A Whole Lot More!.
The Natural Rubber Cleaning Eraser Stick Removes Most All Of The Residue. Use Stick After Your Sander Has Been Clogged With Wood Dust And/Or Wood Resin To Return The Sanding Surface To A Like-New Condition; Pulls Dust, Wood Particles, Sap, Metal Shavings, Paint, And Other Residue Out Of Sanders And Other Abrasive Materials..
Features
- Sanding most anything is a chore that we all don t typically care to do. To make things worse, the sandpaper seems to become useless just after a few strokes. What if you could rejuvenate your sandpaper so you could get a whole lot more mileage out of it? Now you can with our natural rubber cleaning eraser stick! Simply rub the stick across the abrasive surface and watch the dust, crud, resin and natural build up disappear!
- The natural rubber cleaning eraser stick removes most all of the residue. Use stick after your sander has been clogged with wood dust and/or wood resin to return the sanding surface to a like-new condition; Pulls dust, wood particles, sap, metal shavings, paint, and other residue out of sanders and other abrasive materials.
- It works almost like an old fashioned pencil eraser. As you rub or slide the stick across an abrasive surface the stick quickly loosens and removes foreign materials. Your abrasives will be brought back to life to continue sanding. If you have power sanders like belt sanders you can simply hold the stick up against the sanding belt while the power is on and watch the belt be cleaned right before your eyes!
- Clean various items around the house, workshop or in the garage. The rubber construction of the stick works best on belt sanders to allow your belts to cut faster and last longer all the while it can also be used on disc sanders, drum sanders, rubber bottom shoes (not plastic), skateboard grip tape, grip tape and a whole lot more!
- The natural rubber cleaning eraser stick also works exceptionally well on skateboard grip surfaces which tend to get dirty rather quickly. Once clean, the skateboard surface is almost as good as new and keeps its grip a whole lot longer. Similar to skateboard grip surfaces, abrasive or grip tape that s used on floor areas that can get slippery can be easily cleaned using the eraser stick.
- See more on Amazon...
Brand: Peachtree Woodworking Supply | Manufacturer: Peachtree Woodworking Supply Inc.
Weight: 0.57 Pounds
See On Amazon #4
Peachtree Woodworking Supply Safety Woodworking Push Block and Stick Package 5 Piece Set In Orange Color, Ideal for Woodworkers and Use On Router Tables, Jointers and Band Saws
Asin: B07HKJSDP3 | Model: 1201 | PartNumber: 1201 | Ean: 0810948015444 | UPC: 810948015444
The General Idea Behind These Safety Devices Is To Help You Guide And Control Your Stock When Feeding Through A Table Saw, Band Saw, Jointer Or A Router Table. The Push Blocks Are Generally Used On Jointers And Some Router Applications, While The Push Sticks Are Primarily Used On Table Saw Projects. All Five Devices Help Prevent Kickback And Protect Your Fingers And Hands During Your Cutting Process.
The 5 Piece Safety Kit Includes 2 Each Small Push Blocks (1 Angled Handle And 1 Offset Handle Small Push Block), 1 Each Long Or Large Push Block, 1 Each Standard Width Push Stick And 1 Narrow Width Safety-V Push Stick..
Soft, Receptive, Rubber Foam Pads Line The Bases Of The Two Small Push Blocks And The Large Push Block. The Rubber Soles Make Pushing And Controlling Your Stock Much Easier And Safer Then When Doing It By Hand. The Soles Are Also Washable With With Warm Water. Must Let The Rubber Soles Dry For 24 Hours Prior To Using Them Again..
Each Device In This Kit Is Intentionally Made In The Safety Orange Color For High Visibility When In Use. This Provides The User The Ability To See Exactly There Hands Are At During The Cutting Or Milling Process. Being Safety Orange Also Allows For You To Easily Find The Device When Its Not In Its Normal Location..
Features
- This five piece safety kit is designed to be your essential safety protection to help from getting to close to the cutters or blades on a router table, shaper, band saw, table saw and jointer. From the narrow v-style push stick, to the beefy long push block, this kit has all the bases covered in regards to many different woodworking applications.
- Each device in this kit is intentionally made in the SAFETY ORANGE color for high visibility when in use. This provides the user the ability to see exactly there hands are at during the cutting or milling process. Being SAFETY ORANGE also allows for you to easily find the device when its not in its normal location.
- The general idea behind these safety devices is to help you guide and control your stock when feeding through a table saw, band saw, jointer or a router table. The push blocks are generally used on jointers and some router applications, while the push sticks are primarily used on table saw projects. All five devices help prevent kickback and protect your fingers and hands during your cutting process
- Soft, receptive, rubber foam pads line the bases of the two small push blocks and the large push block. The rubber soles make pushing and controlling your stock much easier and safer then when doing it by hand. The soles are also washable with with warm water. Must let the rubber soles dry for 24 hours prior to using them again.
- The 5 piece safety kit includes 2 each small push blocks (1 angled handle and 1 offset handle small push block), 1 each long or large push block, 1 each standard width push stick and 1 narrow width safety-v push stick.
- See more on Amazon...
Brand: Peachtree Woodworking Supply | Manufacturer: Peachtree Woodworking Supply Inc
Weight: 2.05 pounds
See On Amazon #5
Sili Brand Silicone Rubber Glue Roller & Tray for Arts Crafts Woodworking Projects
Asin: B089QRP6J6 | Model: 4614 | PartNumber: 4614 | Ean: 0817918021689 | UPC: 817918021689
The Roller Itself Is A Has No Protruding Metal On One Side To Allow For Flush Passes On Your Glue Ups. This Means You Can Apply Glue Right Up Against Another Board And Have No Worries About Marring That Work Piece. This Also Makes It Easier To Glue Right Up To The Edge Of Your Project..
Both The Sili Roller And Tray Are Of Course Made From Silicone Rubber Which Means They Are Super Easy To Clean! You Can Simply Run Them Under Warm Water And Quickly Work The Glue Off With Your Fingers. You Can Also Let The Glue Dry Overnight And Then Crack And Peel The Glue Off Revealing A Clean, Ready To Go Surface Underneath. Either Way, It’S Quick And Virtually Painless To Clean The Sili Roller And Tray!.
Made Entirely Of Silicone Rubber, The Sili Tray Resembles A Paint Roller Tray But On A Smaller Scale And It Is More Flexible To Easily Dispense The Adhesives Back Into The Container After You Are Done. The Tray Has Been Designed For Use With The Sili Glue Roller (Not Included And Sold Separately), However It Can Be Used With Any Glue Brush Or Applicator That Fit Within Its Dimensions..
The Sili Glue Roller Is Made With Angled Grooves Which Allow The Glue To Be Worked Into The Roller And Help Retain The Glue On The Roller. The Recessed Grooves Also Keep The Glue From Dripping Too Quickly And Gives You Ample Time To Apply The Glue To Your Project Regardless Of Size. The Grooves Also Allow Just Enough Glue “Flow-Through” To Keep Things Rolling With Minimal Resistance. This Also Helps To Keep The Roller From Gliding Or Skating Across The Wood When Applying The Glue..
Features
- Designed to work together, the Sili Glue Roller and the Sili Glue Tray help you make quick work of larger glue up projects. It doesn t matter if you re an arts and crafts hobbyist, a professional woodworker or model making enthusiast, this combo pack will be a useful tool when you need to perform larger glue ups on your projects.
- The Sili Glue Roller is made with angled grooves which allow the glue to be worked into the roller and help retain the glue on the roller. The recessed grooves also keep the glue from dripping too quickly and gives you ample time to apply the glue to your project regardless of size. The grooves also allow just enough glue flow-through to keep things rolling with minimal resistance. This also helps to keep the roller from gliding or skating across the wood when applying the glue.
- The roller itself is a has no protruding metal on one side to allow for flush passes on your glue ups. This means you can apply glue right up against another board and have no worries about marring that work piece. This also makes it easier to glue right up to the edge of your project.
- Made entirely of silicone rubber, the Sili tray resembles a paint roller tray but on a smaller scale and it is more flexible to easily dispense the adhesives back into the container after you are done. The tray has been designed for use with the Sili Glue Roller (not included and sold separately), however it can be used with any glue brush or applicator that fit within its dimensions.
- Both the Sili Roller and Tray are of course made from silicone rubber which means they are super easy to clean! You can simply run them under warm water and quickly work the glue off with your fingers. You can also let the glue dry overnight and then crack and peel the glue off revealing a clean, ready to go surface underneath. Either way, it s quick and virtually painless to clean the Sili Roller and Tray!
- See more on Amazon...
Brand: Sili | Manufacturer: Peachtree Woodworking Supply Inc.
Weight: 1.00 pounds
See On Amazon #6
Fulton Precision Miter Gauge with Aluminum Miter Fence with 45 degree Angled Ends for Maximum Stock Support and a Repetitive Cut Flip Stop
Asin: B087XWCV61 | Model: 11567 | PartNumber: 11567 | Ean: 0817918022532 | UPC: 817918022532
The Head Is Mounted To A Solid Steel Miter Bar That Measure 18” In Length And Is .354” Thick By .730” Wide. Standard Miter Slots Are 3/4” X 3/8” With A 1/8” “T” Slot (Slight Variances From Brand To Brand) Running The Length On The Bottom Of The Slot. The Steel Miter Bar Is Equipped With A Metal, Removable Retaining Disc That Measures 7/8” In Diameter And Is Just Shy Of 1/8” To Fit Into To The “T” Slot To Prevent Accidental Lifting When Feeding Your Stock Through..
Both Ends Of The Fence Are Cut At Exactly 45 Degrees. This Allows You To Position The Fence Extra Close To The Saw Blade (With The Power Turned Off) So You Have Even More Control Over The Workpiece You Are Cutting. The Fence Comes With A Flip Stop That Makes Repetitive Cuts A Breeze. When Not In Use The Flip Stop Can Be Flipped Up And Out Of The Way. Also Include Are Two Sticky Back Measuring Tapes. 1 Tape Is Left To Right Reading And The Other Is Right To Left Reading..
Made From A Single Piece Of Extruded Aluminum, This Precision Miter Gauge Fence Is Not Only Durable, Its Accurate And Saves Setup Time. The Fence Is Designed To Be Used With Most Any Miter Gauge With Its Off-Set Mounting Track On The Back Of The Fence. The Off-Set Track Allows You To Flip The Fence For Lower Profile Miter Gauge Mounts And Flip Back For Standard Height Miter Gauges. The Fence Can Be Mounted To Older Miter Gauges By Adding A Wooden Block Mount With Wooden Screws If Necessary..
The .200” Thick, Adjustable, Solid Aluminum Head Is Machined With 13 Positive Stop Holes. 1 Hole Is At 90 Degrees While The 6 Holes On Both Sides Are At 22.5, 30, 45, 60, 67.5 And 90 Degrees. The Positive Stops Are Perfect For Many Woodworking Projects As They Are The Angles That Are Typically Used.To Adjust The Head You Simply Loosen The Post Knob Handle, Pull The Spring Loaded Indexing Pin Outward, Rotate The Head To The Desired Position, Release The Pin And Lock Into Place..
Features
- The Fulton Miter Gauge is a high quality, well thought out and economical solution for your table saw cross cutting needs.The Aluminum Miter fence is equally well thought out with its 45 degree ends for unsurpassed workpiece support and its ability to mounted to most any miter gauge. Also included is a handy aluminum flip stop for repetitive angled cuts on your table saw. Together these three items are the perfect compliment to each other for your table saw cutting needs.
- The .200 thick, adjustable, solid aluminum head is machined with 13 positive stop holes. 1 hole is at 90 degrees while the 6 holes on both sides are at 22.5, 30, 45, 60, 67.5 and 90 degrees. The positive stops are perfect for many woodworking projects as they are the angles that are typically used.To adjust the head you simply loosen the post knob handle, pull the spring loaded indexing pin outward, rotate the head to the desired position, release the pin and lock into place.
- The head is mounted to a solid steel miter bar that measure 18 in length and is .354 thick by .730 wide. Standard miter slots are 3/4 x 3/8 with a 1/8 T slot (slight variances from brand to brand) running the length on the bottom of the slot. The steel miter bar is equipped with a metal, removable retaining disc that measures 7/8 in diameter and is just shy of 1/8 to fit into to the T slot to prevent accidental lifting when feeding your stock through.
- Made from a single piece of extruded aluminum, this precision miter gauge fence is not only durable, its accurate and saves setup time. The fence is designed to be used with most any miter gauge with its off-set mounting track on the back of the fence. The off-set track allows you to flip the fence for lower profile miter gauge mounts and flip back for standard height miter gauges. The fence can be mounted to older miter gauges by adding a wooden block mount with wooden screws if necessary.
- Both ends of the fence are cut at exactly 45 degrees. This allows you to position the fence extra close to the saw blade (with the power turned off) so you have even more control over the workpiece you are cutting. The fence comes with a flip stop that makes repetitive cuts a breeze. When not in use the flip stop can be flipped up and out of the way. Also include are two sticky back measuring tapes. 1 tape is left to right reading and the other is right to left reading.
- See more on Amazon...
Brand: Fulton | Manufacturer: Fulton Woodworking Tools Inc.
Dimensions: 0.00 x 0.00 x 0.00 inches | Weight: 2.50 pounds
See On Amazon #7
2-1/2 inch Diameter by 10 foot Long PVC Dust/Debris Collection Hose MADE IN THE USA with 2 each 2.5 inch Turnkey Stainless Steel Hose Clamps
Asin: B09BNVHJ21 | Model: 6173 | PartNumber: 6173 | Ean: 0817918023119 | UPC: 817918023119
Pvc Hose (Depending On Diameter) Can Be Used With Dust Collectors, Shop Vacuums, Industrial Vacuum Systems, Lawn Tractor Leaf Catchers And A Whole Lot More! Simply Make Sure Both Ends Of The Hose Are Secured With Hose Clamps And Your Ready To Go. The Pvc Hose Flexes Enough To Weave In And Out Of Shop Machinery Or Table Legs Without Kinking. Its Also Sturdy Enough That It Won’T Flatten Out When The Dust Collector Is Turned On. The Hose Has A Compression Ratio Of 3: 1..
304 Stainless Steel Hose Clamp- The 2 ½” Diameter Large Hose Duct Clamp (Including The Housing, The Band And The Internal Screw Are Made From Premium 304 Stainless Steel. This Makes The Clamp Strong, Durable And Rust Resistant Which Makes It Ideal For Many Applications In The Shop Or Around The Home..
No More Tools! – Set Your Tools Aside When Installing Your Ductwork Or Hose With These Handy, Easy To Tighten Hose/Duct Clamps. Place The Clamp Where Its Needed Then Simply Turn The Key To Loosen Or Tighten Them..
Typically, Pvc Hose Works Best As A Dust Collection Hose For Woodworking Applications Where Dust And Chips From Cutting, Milling Or Sanding Wood Is A Problem. This Heavy-Duty Hose Will Stand Up To Small And Large Chunks Of Wood Without Getting Punctured As Well As Handle The Smallest Of Saw Dust Without Leaking. Pvc Hose Can Be Used As A Primary Line Or Can Be Plugged Into And Out Of Machinery As Needed..
Features
- When setting up our dust collection or filtration systems we tend to have a lot of moving parts during this process and trying to figure out what type of line, piping or hose to use can be challenging. Dust collection hoses need to be not only long enough, but it must be durable, flexible and sturdy enough, so it won t completely collapse in use. It must also perform under the constant use and abuse of an everyday workshop environment. This PVC hose checks all of those boxes and more!
- Typically, PVC hose works best as a dust collection hose for woodworking applications where dust and chips from cutting, milling or sanding wood is a problem. This heavy-duty hose will stand up to small and large chunks of wood without getting punctured as well as handle the smallest of saw dust without leaking. PVC hose can be used as a primary line or can be plugged into and out of machinery as needed.
- PVC Hose (depending on diameter) can be used with dust collectors, shop vacuums, industrial vacuum systems, lawn tractor leaf catchers and a whole lot more! Simply make sure both ends of the hose are secured with hose clamps and your ready to go. The PVC hose flexes enough to weave in and out of shop machinery or table legs without kinking. Its also sturdy enough that it won t flatten out when the dust collector is turned on. The hose has a compression ratio of 3: 1.
- NO MORE TOOLS! Set your tools aside when installing your ductwork or hose with these handy, easy to tighten hose/duct clamps. Place the clamp where its needed then simply turn the key to loosen or tighten them.
- 304 STAINLESS STEEL HOSE CLAMP- The 2 diameter large hose duct clamp (including the housing, the band and the internal screw are made from premium 304 stainless steel. This makes the clamp strong, durable and rust resistant which makes it ideal for many applications in the shop or around the home.
- See more on Amazon...
Brand: Peachtree Woodworking Supply | Manufacturer: Peachtree Woodworking Supply Inc.
Dimensions: 0.10 x 120.00 x 2.50 inches
See On Amazon #8
Sili Complete Silicone Glue Kit Wood Glue Up 4Piece Kit 2 Pack of Silicone Brushes 1 Tray 1 Comb Woodworking Glue Spreader Applicator Set
Asin: B00CPTGGNO | Model: 4020 | PartNumber: 4020 | Ean: 0814310017005 | UPC: 814310017005
What If You Need To Apply Glue To Larger Areas? We’Ve Thought Of That And Included The Super Handy Sili Comb/Squeegee! The Comb Side Is Approx. 3½ Inches Wide Making It Perfect For Larger Surfaces Areas Like When You Need To Laminate Two Pieces Of Wood Together. The Comb Leaves Perfect Glue Grooves For Better Coverage And Adhesion. The Squeegee Side Is About 2 Inches Wide And It Leaves A Smooth Flat Glue Surface Which Is Great For Many Arts And Crafts..
Each Of The Items In This Super Convenient Set Are Made From Silicone Rubber Which Makes Them Very Easy To Clean. Clean The Brushes, Comb/Squeegee Or Even The Tray Using Warm Water. You Can Also Let Your Wood Glue Or White School Glue Dry Over Night And The Glue Will Peel Right Off Revealing A Fresh Glue Brush, Comb/Squeegee Or Tray! Pack Includes 1Ea. 1 Inch Brush, 1Ea. ½ Inch Brush, 1 Ea. Comb/Squeegee And 1 Ea. Tray..
The Sili Glue Tray Is The Perfect Holder/Dispenser For You Glue While Your Working. Simply Pour Or Squeeze More Glue Than You’Ll Need Into The Tray And Dip The Sili Comb/Squeegee Or One Of The Brushes Into The Glue. When Your Done Applying Glue To Your Project, You Can Pour The Remaining Glue Back Into Your Glue Bottles Using The Funnel End Tip On The Glue Tray..
The Two Sili Glue Brushes Have Two Different Size Brush Heads. One Head Is ½” And The Other Is 1” Wide. The Smaller Brush Head Of The ½” Brush Makes It Ideal For Applying Glue To Narrow Strips And Makes It Easier To Work Small Pieces. The Larger 1” Brush Is Perfect For Applying Wood Glue To Thicker Stock Pieces. Each Brush Tip Is Made From Silicone And Is Easy To Clean With Warm Water..
Features
- The Complete Sili Glue Kit includes 2 different size Sili brushes, the Sili Glue Tray and the versatile Sili Glue Comb/Squeegee. All 4 of these items together provide you with all the glue up tools you need to get you going on your next projects. Ideal for woodworkers, arts and crafts, hobbyists and more!
- The two Sili Glue Brushes have two different size brush heads. One head is and the other is 1 wide. The smaller brush head of the brush makes it ideal for applying glue to narrow strips and makes it easier to work small pieces. The larger 1 brush is perfect for applying wood glue to thicker stock pieces. Each brush tip is made from silicone and is easy to clean with warm water.
- What if you need to apply glue to larger areas? We ve thought of that and included the super handy Sili Comb/Squeegee! The comb side is approx. 3 inches wide making it perfect for larger surfaces areas like when you need to laminate two pieces of wood together. The comb leaves perfect glue grooves for better coverage and adhesion. The squeegee side is about 2 inches wide and it leaves a smooth flat glue surface which is great for many arts and crafts.
- The Sili Glue Tray is the perfect holder/dispenser for you glue while your working. Simply pour or squeeze more glue than you ll need into the tray and dip the Sili Comb/Squeegee or one of the brushes into the glue. When your done applying glue to your project, you can pour the remaining glue back into your glue bottles using the funnel end tip on the glue tray.
- Each of the items in this super convenient set are made from silicone rubber which makes them very easy to clean. Clean the brushes, comb/squeegee or even the tray using warm water. You can also let your wood glue or white school glue dry over night and the glue will peel right off revealing a fresh glue brush, comb/squeegee or tray! Pack includes 1ea. 1 inch brush, 1ea. inch brush, 1 ea. Comb/squeegee and 1 ea. Tray.
- See more on Amazon...
Brand: Sili | Manufacturer: Sili Brand
Dimensions: 0.50 x 11.00 x 8.00 inches | Weight: 0.10 pounds
See On Amazon #9
Keystone 100 Sanding Twigs or Sticks Ideal for Woodworking Hobby Arts Crafts Models Mixed Grits and Lengths Cushioned Abrasive
Asin: B00C5RFIXK | Model: 11570 | PartNumber: 11570 | Ean: 0817918022600 | UPC: 817918022600
The Grits In This Kit - Fine, Medium, And Coarse Grits Will Be Found On These Pencil Sized Detailing Sanders. But To Be More Specific Here Are The Grits You Can Expect To See May Be: 80, 100, 120, 180, 220, 240, 320. If You See Red The Grit Is 80, Yellow Is 240, Light Blue Is 240 And Dark Blue Is 120. If You See Black, Gray Or White It Can Be Anything Between 80 And 240. Each 100 Piece Assortment Pack Is Different..
You Will Get - 5 Assorted Sanding Twig Packs, Each Pack Will Have 20 Sanding Twigs Inside. This Will Be A Total Of 100 Pieces For The Multipack. The Twigs Are Approximately 5-1/2 Inches Long To 7 Inches Long And The Thickness Will Also Vary From 1/16 Of An Inch Up To 1/4 Of An Inch. The Colors On Each Twig Will Also Vary From Pack To Pack. No Two Packs Are Alike..
Key Features - Great For A Tight Sanding Spot, Will Work In Hard To Reach Corners, Will Remove Paint, Polish And More. Will Reach Spots That Pads, Blocks, Belts And Discs Can't. Own That Micro Project And Upgrade From Regular Sheets Of Sandpaper. The Bottom Lie Is That You Will Be Able To Sand In Areas That You Normally Would Not Have Been Able To Reach With The Keystone Cushioned Abrasive Sanding Twigs..
Very Strong Adhesive - The Adhesive Will Maintain Its Bond And Not Peel Away When Used Under Normal Working Conditions. These Twigs Are Not Meant For Industrial Or Commercial Use And Should Not Be Used To Remove Large Amounts Of Material. These Are Less Of A Polishing Tool And More Of A File When Comparing To Other Similar Types Of Sanding Sticks Or Twigs. They Are Ideal For De-Burring Small Tight Areas That Are Normally Hard To Get To..
Features
- CUSHIONED ABRASIVE SANDING TWIGS ideal solution to the age old issue of sanding in small, tight spaces. Can be used on just about any type of material including, wood, metal, plastics, resins and more! Each twig has a polystyrene core layered with foam and sandpaper which creates a receptive cushioned abrasive surface. This comes in really handy with more delicate materials and projects.
- VERY STRONG ADHESIVE - The adhesive will maintain its bond and not peel away when used under normal working conditions. These twigs are not meant for industrial or commercial use and should not be used to remove large amounts of material. These are less of a polishing tool and more of a file when comparing to other similar types of sanding sticks or twigs. They are ideal for de-burring small tight areas that are normally hard to get to.
- THE GRITS IN THIS KIT - Fine, medium, and coarse grits will be found on these pencil sized detailing sanders. But to be more specific here are the grits you can expect to see may be: 80, 100, 120, 180, 220, 240, 320. If you see red the grit is 80, Yellow is 240, Light blue is 240 and dark blue is 120. If you see black, gray or white it can be anything between 80 and 240. Each 100 piece assortment pack is different.
- KEY FEATURES - Great for a tight sanding spot, will work in hard to reach corners, will remove paint, polish and more. Will reach spots that pads, blocks, belts and discs can't. Own that micro project and upgrade from regular sheets of sandpaper. The bottom lie is that you will be able to sand in areas that you normally would not have been able to reach with the Keystone Cushioned Abrasive Sanding Twigs.
- YOU WILL GET - 5 assorted sanding twig packs, each pack will have 20 sanding twigs inside. This will be a total of 100 pieces for the multipack. The twigs are approximately 5-1/2 inches long to 7 inches long and the thickness will also vary from 1/16 of an inch up to 1/4 of an inch. The colors on each twig will also vary from pack to pack. No two packs are alike.
- See more on Amazon...
Brand: Keystone | Manufacturer: Keystone
Weight: 0.26 pounds
See On Amazon #10
Fulton 2 1/2 Inch Thumb Screw Key Adjustable 304 Stainless Steel Hose Clamps, Pipe Clamp, Worm Gear Clamps, Dryer Vent Clamp, Dust Collection, Automotive, RV Clamp 5 pack (2 1/2" Hose Clamps)
Asin: B07PFPWGHD | Ean: 0817918022075 | UPC: 817918022075
Large Easy To Turn Key - The Easy To Turn And Easy To See Blue Key Is Made From A Strong And Durable Polymer. The Key Is Designed To Make The Securing And Un-Securing Of Hose Much Easier On The Knuckles. No More Knuckle Busting Flat Head Screw Drivers Or Tiny Socket Wrenches. Simply To Turn The Key Clockwise To Tighten, Counter Clockwise To Loosen..
Flexible Adjustable Size Range- 2 1/2 Inch Hose Clamps Are Flexible And Workable With A Rather Wide Adjustable Size Range From Appx. 2-7/8” (2.877” Or 73.08Mm) In Full Diameter Down To Appx. 1-7/8” (1.874” Or 47.61Mm) At Its Most Compact Diameter..
Flexible Adjustable Size Range- 2 1/2 Inch Hose Clamps Are Flexible And Workable With A Rather Wide Adjustable Size Range From Appx. 2-7/8” (2.877” Or 73.08Mm) In Full Diameter Down To Appx. 1-7/8” (1.874” Or 47.61Mm) At Its Most Compact Diameter..
304 Stainless Steel Hose Clamp- The 2 ½” Diameter Large Hose Duct Clamp (Including The Housing, The Band And The Internal Screw Are Made From Premium 304 Stainless Steel. This Makes The Clamp Strong, Durable And Rust Resistant Which Makes It Ideal For Many Applications In The Shop Or Around The Home..
Features
- NO MORE TOOLS! Set your tools aside when installing your ductwork or hose with these handy, easy to tighten hose/duct clamps. Place the clamp where its needed then simply turn the key to loosen or tighten them.
- 304 STAINLESS STEEL HOSE CLAMP- The 2 diameter large hose duct clamp (including the housing, the band and the internal screw are made from premium 304 stainless steel. This makes the clamp strong, durable and rust resistant which makes it ideal for many applications in the shop or around the home.
- LARGE EASY TO TURN KEY - The easy to turn and easy to see blue key is made from a strong and durable polymer. The key is designed to make the securing and un-securing of hose much easier on the knuckles. No more knuckle busting flat head screw drivers or tiny socket wrenches. Simply to turn the key clockwise to tighten, counter clockwise to loosen.
- FLEXIBLE ADJUSTABLE SIZE RANGE- 2 1/2 inch hose clamps are flexible and workable with a rather wide adjustable size range from appx. 2-7/8 (2.877 or 73.08mm) in full diameter down to appx. 1-7/8 (1.874 or 47.61mm) at its most compact diameter.
- FLEXIBLE ADJUSTABLE SIZE RANGE- 2 1/2 inch hose clamps are flexible and workable with a rather wide adjustable size range from appx. 2-7/8 (2.877 or 73.08mm) in full diameter down to appx. 1-7/8 (1.874 or 47.61mm) at its most compact diameter.
- See more on Amazon...
Brand: Fulton | Manufacturer: Fulton Woodworking Tools and Accessories
See On Amazon
Looking For Something Else?
Search