Vogurtime 4 Channel 5V Relay Module with Optocoupler Isolation Support High and Low Level Trigger Relay Red Board
Asin: B07K5D7XNW | Model: 4-RELAY | PartNumber: 4-RELAY | Ean: 0681413170247 | UPC: 681413170247
As an Amazon Associate we earn a fee from qualifying purchases when you follow a link to Amazon from this page. We rank the products, but the links to Amazon are promotional."High", "Low" Level Controllable - With A Jumper Cap, You Can Choose A Low Level Control Or A High Level Control, Allowing The Relay Module To Adapt To More Occasions..
User-Friendly Interface Design - All Interfaces Can Be Directly Connected Through The Terminal Block, Which Is Very Convenient.
It Has A Fault-Tolerant Design - Even If The Control Line Is Broken, The Relay Won't Actuation..
Adopts Smd Optocoupler Isolation - Use Two Sets Of Fully Isolated Power Supply System Power, To Ensure That The Relay In The Switch Will Have An Impact On The Signal Circuit And Can Be Freely Switched To High Level Drive Mode Or Low Level Drive Mode. Trigger Current Is 5Ma..
Features
- High Quality Module - the relay module uses genuine high-quality relays. The maximum load of the frequently opened interface is: AC 250v/10a, DC 30v/10a.
- Adopts SMD Optocoupler Isolation - Use two sets of fully isolated power supply system power, to ensure that the relay in the switch will have an impact on the signal circuit and can be freely switched to high level drive mode or low level drive mode. Trigger Current is 5mA.
- High, Low Level Controllable - With a jumper cap, you can choose a low level control or a high level control, allowing the relay module to adapt to more occasions.
- It Has a Fault-Tolerant Design - Even if the control line is broken, the relay won't actuation.
- User-friendly Interface Design - All interfaces can be directly connected through the terminal block, which is very convenient
- See more on Amazon...
Brand: VOGURTIME | Manufacturer: Vogurtime
See On Amazon Similar To Vogurtime 4 Channel 5V Relay
#1
KeeYees 5pcs 1 Channel 5V Relay Module Board Shield KY-019 LED Indicator for Arduino + 3pcs 20CM 10Pin Female Male Jumper Wires
Asin: B07L6J6FHH | Model: KYES504-KY019-5 | PartNumber: KYES504-KY019-5 | Ean: 0705883356380 | UPC: 705883356380
No Need To Buy The Jumper Wires Extra, This Set Contains 20Cm 10Pin Female To Female, Female To Male, Male To Male Dupont Jumper Wires, With Which You Can Easier To Complete The Project..
This Relay Can Be Used Not Only As A Microcontroller Development Board Module, But Also As A Home Appliance Controller..
Features
- The relay can directly control a variety of equipment and loads, which meets international safety standards, and also has power and relay indicators.
- This relay can be used not only as a microcontroller development board module, but also as a home appliance controller.
- No need to buy the Jumper Wires extra, this set contains 20cm 10Pin female to female, female to male, male to male Dupont Jumper Wires, with which you can easier to complete the project.
- See more on Amazon...
Brand: KeeYees | Manufacturer: KeeYees
See On Amazon #2
HiLetgo 2pcs 5V One Channel Relay Module Relay Switch with OPTO Isolation High Low Level Trigger
Asin: B00LW15A4W | Model: 3-01-0340 | PartNumber: 3-01-0340 | Ean: 0702082655948 | UPC: 702082655948
Fault-Tolerant Design, Even If The Control Line Is Broken, The Relay Will Not Move..
The Module Can Be Set By Jumper High Or Low Trigger..
The Interface Design Of Human Nature, All Interfaces Are Available Through A Direct Connection Terminal Leads, Very Convenient..
Using Smd Optocoupler Isolation, Strong Driving Capability, Stable Performance; Trigger Current 5Ma..
Features
- The module uses genuine quality relay, normally open interfaces , Maximum load: AC 250V/10A, DC 30V/10A.
- Using SMD optocoupler isolation, strong driving capability, stable performance; trigger current 5mA.
- Fault-tolerant design, even if the control line is broken, the relay will not move.
- The interface design of human nature, all interfaces are available through a direct connection terminal leads, very convenient.
- The Module can be set by jumper high or low trigger.
- See more on Amazon...
Brand: HiLetgo | Manufacturer: HiLetgo
See On Amazon #3
AEDIKO 4pcs DC 5V Relay Module 1 Channel Relay Switch Relay Board with Optocoupler Isolation Support High or Low Level Trigger
Asin: B095YD3732 | Ean: 0701715480582 | UPC: 701715480582
Optocoupler Isolation:1 Channel Relay Board Use Optocoupler Isolation That Has Strong Driving Ability And Stable Performance ,The Isolation Circuit Prevent Damages To I / O Port By Relay Switch Current.
Wide Application: Dc 5V Relay Module Works Well With Arm /Pic /Avr /Mcu/Raspberry/Cnc Machine/ Ps4 Etc..
Jumper Design: The Relay Module Has A Jumper That You Can Set Rather The Unit State Changes With High Or Low Signal. Has Screw Terminals For Relay (Nc,C,No) And For Input; Coil +, Coil - And Trigger..
Fault-Tolerant Design: Fault Tolerant Design, Even If The Control Line Is Broken, The Relay Will Not Operate;All Interfaces Of Relay Can Be Wired Out Through The Terminals Directly,Normally Open And Normally Closed.
Features
- 5V Relay Module: Working Voltage: DC 5V; Maximum Load: AC 250V/10A, DC 30V/10A; Trigger Current of Opto-Isolator: 5mA
- Fault-Tolerant Design: Fault Tolerant Design, Even if the Control Line is Broken, the Relay will not Operate;All Interfaces of Relay can be Wired Out Through the Terminals Directly,Normally Open and Normally Closed
- Optocoupler Isolation:1 Channel Relay Board use Optocoupler Isolation that has Strong Driving Ability and Stable Performance ,The Isolation Circuit Prevent Damages to I / O Port by Relay Switch Current
- Jumper Design: The Relay Module has a Jumper That You Can Set Rather the Unit State Changes with High or Low Signal. Has Screw Terminals for Relay (NC,C,NO) and for Input; Coil +, Coil - and Trigger.
- Wide Application: DC 5V Relay Module Works Well with ARM /PIC /AVR /MCU/Raspberry/CNC Machine/ PS4 etc.
- See more on Amazon...
Brand: AEDIKO | Manufacturer: AEDIKO
Dimensions: 0.72 x 1.90 x 1.02 inches
See On Amazon #4
SunFounder Lab 4 Relay Module 5V 4 Channels Relay Module Compatible with Arduino R3 1280 Arm PIC AVR STM32
Asin: B00E0NSORY | Ean: 0520141421286 | UPC: 520141421286
Standard Interface That Can Be Controlled Directly By Microcontroller (Compatible With Arduino , 8051, Avr, Pic, Dsp, Arm, Arm, Msp430, Ttl Logic)..
Applications: Supports All Mcu Control, The Industrial Field, Plc Control, Smart Home Control, Vcc System Power And So On..
Indication Led’S For Relay Output Status..
Equiped With High-Current Relay, Ac250v 10A ; Dc30v 10A..
Features
- 5V 4-Channel Relay interface board, and each one needs 15-20mA Driver Current.
- Equiped with high-current relay, AC250V 10A ; DC30V 10A.
- Standard interface that can be controlled directly by microcontroller (Compatible with Arduino , 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic).
- Indication LED s for Relay output status.
- Applications: Supports all MCU control, The industrial field, PLC control, Smart home control, VCC system Power and so on.
- See more on Amazon...
Brand: SunFounder | Manufacturer: SunFounder
Dimensions: 0.80 x 3.20 x 2.90 Inches | Weight: 0.09 Pounds
See On Amazon #5
ANMBEST 2PCS 4 Channel 5V Relay Module with Optocoupler High or Low Level Trigger Expansion Board for Raspberry Pi Arduino
Asin: B08PP8HXVD | Model: ANMBEST_MD314-319 | PartNumber: ANMBEST_MD314-319 | Ean: 7903265708922
Reliable: Fault-Tolerant Design, Even If The Control Line Breaks, The Relay Will Not Move; With Optical Coupling Isolation, Triggering More Reliable, More Stable..
High/Low Level Trigger Can Be Selected By Jumper. Very Versatile, You Can Reverse The Input Logic With The Jumper..
Easy To Install: Equipped With Screwed Terminal Plate And Fixed Bolt Holes(Diameter: 3.1 Mm) On Both Sides For Easy Installation..
Equipped With High-Current Relay, Maximum Load: Ac250v 10A, 15A 125Vac, Dc30v 10A; Trigger Current Of Opto-Isolator: 5Ma..
Features
- It is 4 Channel Isolated 5V 10A Relay Module, each relay can individually switch on/off by an opto-isolated digital input, Standard interface can be directly connected with microcontrollers and be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, DSP, etc., very convenient.
- Equipped with high-current relay, maximum load: AC250V 10A, 15A 125VAC, DC30V 10A; Trigger current of opto-isolator: 5mA.
- RELIABLE: Fault-tolerant design, even if the control line breaks, the relay will not move; With optical coupling isolation, triggering more reliable, more stable.
- EASY to INSTALL: Equipped with screwed terminal plate and fixed bolt holes(diameter: 3.1 mm) on both sides for easy installation.
- High/Low level trigger can be selected by jumper. Very versatile, you can reverse the input logic with the jumper.
- See more on Amazon...
Brand: ANMBEST | Manufacturer: ANMBEST
See On Amazon #6
Teyleten Robot DC 1 Channel Optocoupler 3V/3.3V Relay High Level Driver Module Isolated Drive Control Board 3V/3.3V Relay Module for Arduino (Pack of 5)
Asin: B07XGZSYJV | Model: RK-S1B4-G97L | PartNumber: RK-S1B4-G97L | Ean: 0724545020568 | UPC: 724545020568
Optocoupler Isolator:3V/3.3V Power Relay Module Supports Photocoupler Isolation Control..
30Vdc 250Vac Load：The Power Switch Is Compatible With 10A 250Vac And 10A 30Vdc Load..
Features
- Original Songle Relay
- 30VDC 250VAC Load The power switch is compatible with 10A 250VAC and 10A 30VDC load.
- Optocoupler Isolator:3V/3.3V power relay module supports photocoupler isolation control.
- See more on Amazon...
Brand: Teyleten Robot | Manufacturer: Teyleten Robot
Dimensions: 0.79 x 2.76 x 0.67 Inches | Weight: 0.00 Pounds
Warranty: no
See On Amazon #7
5v Relay Module 1 Channel Relay Board for Raspberry Pi with Opto-Isolated High or Low Level Trigger 5v 1 Channel Relay Switch for Arduino
Asin: B09G6H7JDT | Ean: 0734914033952 | UPC: 734914033952
【Adopted Smd Optocoupler Isolation& Jumper Set】- The Isolation Circuit Prevent Damages To I / O Port By Relay Switch Current.The Module Has A Jumper So You Can Set Rather The Unit State Changes With High Or Low Signal. Has Screw Terminals For Relay (Nc,C,No) And For Input; Coil +, Coil - And Trigger..
【Humanization Design On Interfaces】- All Interfaces Can Be Directly Wired Out Through The Terminals.Fault-Tolerant Design;Fault-Tolerant Design,Even If The Control Line Is Broken, The Relay Will Not Operate..
【Wide Application】-These 5V Relay Board Works Well With Arm /Pic /Avr /Mcu/Raspberry/Cnc Machine/ Ps4 Etc..
【Main Specification】- Peak Load Of No Connector: Ac125~250V/10A, Dc28~30V/10A; Trigger Current: 5Ma;The Module Operating Voltage:12V; 4Pcs * 3.1 Mm Fixed Bolt Hole..
Features
- 5V 1 Channel Relay Module - This Relay Board provides a single relay that can be controlled by any 5V digital output from your microcontroller.
- Main Specification - Peak Load of NO Connector: AC125~250V/10A, DC28~30V/10A; Trigger Current: 5mA;The Module Operating Voltage:12V; 4pcs * 3.1 mm Fixed Bolt Hole.
- Adopted SMD Optocoupler Isolation& jumper Set - The isolation circuit prevent damages to I / O port by relay switch current.The module has a jumper so you can set rather the unit state changes with high or low signal. Has screw terminals for relay (NC,C,NO) and for input; Coil +, coil - and trigger.
- Wide Application -These 5v relay board works well with ARM /PIC /AVR /MCU/Raspberry/CNC machine/ PS4 etc.
- Humanization Design On Interfaces - All interfaces can be directly wired out through the terminals.Fault-tolerant design;fault-tolerant design,even if the control line is broken, the relay will not operate.
- See more on Amazon...
Brand: AZKO | Manufacturer: AZKO
Dimensions: 0.10 x 0.10 x 0.10 Inches
See On Amazon #8
ELEGOO 4 Channel DC 5V Relay Module with Optocoupler Compatible with Arduino UNO R3 MEGA 2560 DSP ARM PIC AVR STM32
Asin: B09ZQS2JRD
Working Status Indicator Lights Are Conducive To The Safe Use.
Widely Used For All Mcu Control, Industrial Sector, Plc Control, Smart Home Control. For A Complete Data Sheet For This Relay Board, Please Download It From: Http://Dwz.Win/Uhw.
4-Channel Relay Interface Board, Which Can Be Controlled Directly By A Wide Range Of Microcontrollers Such As Arduino, Avr, Pic, Arm, Plc, Etc. It Is Also Able To Control Various Appliances And Other Equipments With Large Current..
Standard Interface Can Be Directly Connected With Microcontrollers..
Features
- This relay module is 5V active low. Relay output maximum contact is AC250V 10A and DC30V 10A.
- Standard interface can be directly connected with microcontrollers.
- Working status indicator lights are conducive to the safe use
- 4-channel relay interface board, which can be controlled directly by a wide range of microcontrollers such as Arduino, AVR, PIC, ARM, PLC, etc. It is also able to control various appliances and other equipments with large current.
- Widely used for all MCU control, industrial sector, PLC control, smart home control. For a complete data sheet for this relay board, please download it from: http://dwz.win/UhW
- See more on Amazon...
Brand: ELEGOO | Manufacturer: ELEGOO
See On Amazon #9
HiLetgo 12V 4 Channel Relay Module with OPTO-Isolated Support High and Low Level Trigger
Asin: B00LW2GM84 | Model: 3-01-0371 | PartNumber: 3-01-0371 | Ean: 0702082656167 | UPC: 702082656167
High And Low Level Trigger.
Using Smd Optocoupler Isolation.
Features
- HiLetgo 12V 4 Channel Relay Module
- Using SMD OPTOCOUPLER isolation
- High and Low Level Trigger
- See more on Amazon...
Brand: HiLetgo | Manufacturer: HiLetgo
See On Amazon #10
HiLetgo 12V 8 Channel Relay Module with OPTO-Isolated High and Low Level Trigger 8 Ways Relay Switch Module for Arduino
Asin: B00LW2GA5Y | Model: 3-01-0348 | PartNumber: 3-01-0348 | Ean: 0702082656006 | UPC: 702082656006
The Module Can Be High Or Low By A Jumper Setting Trigger;.
The Power Indicator (Green), The Relay Status Indicator (Red)..
Fault-Tolerant Design, Even If The Control Line Is Broken, The Relay Will Not Operate;.
The Module Operating Voltage 12V;.
Features
- 12V 8 Channel Relay Module With OPTO-Isolated High And Low Level Trigger
- The module Operating voltage 12V;
- The module can be high or low by a jumper setting trigger;
- Fault-tolerant design, even if the control line is broken, the relay will not operate;
- The power indicator (green), the relay status indicator (red).
- See more on Amazon...
Brand: HiLetgo | Manufacturer: HiLetgo
Weight: 0.11 pounds
See On Amazon #11
Valefod DC 5V Relay Module 1-Channel Relay Switch with Optocoupler Isolation High/Low Level Trigger, Pack of 10
Asin: B07WQH63FB | Model: VA-0166 | PartNumber: VA-0166 | Ean: 0793118392173 | UPC: 793118392173
【Fault-Tolerant Design】The Relay Will Not Operate Even If The Control Line Is Disconnected..
【High Compatibility】The Relay Module Can Be Controlled Directly By 5V Logic Signals From Microcontroller(8051, Avr, Pic, Dsp, Arm, Raspberry Pi, Msp430, Ttl Logic Etc).
【Universal Interface】Equipped With Screwed Terminal Plate And Fixed Bolt Holes(Diameter: 3.1 Mm) On Both Sides For Easy Installation..
【Load Range】No(Normally Open) Maximum Load < Ac 250V/10A, < Dc 30V/10A. Trigger Current Of Opto-Isolator: 5Ma..
Features
- Control Devices The 1-channel relay module uses genuine high quality DC5V relay and SMD opto-isolator supporting high/low level trigger, widely apply to control various AC/DC appliances, and other devices with large current.
- Load Range NO(Normally open) maximum load < AC 250V/10A, < DC 30V/10A. Trigger current of opto-isolator: 5mA.
- Fault-tolerant Design The relay will not operate even if the control line is disconnected.
- Universal Interface Equipped with screwed terminal plate and fixed bolt holes(diameter: 3.1 mm) on both sides for easy installation.
- High Compatibility The relay module can be controlled directly by 5V logic signals from microcontroller(8051, AVR, PIC, DSP, ARM, Raspberry Pi, MSP430, TTL logic etc)
- See more on Amazon...
Brand: Valefod | Manufacturer: Valefod
See On Amazon #12
Youngneer 5v Relay Module 1 Channel Relay Board for Raspberry Pi with Opto-Isolated High or Low Level Trigger 5v 1 Channel Relay Switch for Arduino
Asin: B0D3D4WTN8 | Model: 5v | PartNumber: 5v
【Adopted Smd Optocoupler Isolation& Jumper Set】- The Isolation Circuit Prevent Damages To I / O Port By Relay Switch Current.The Module Has A Jumper So You Can Set Rather The Unit State Changes With High Or Low Signal. Has Screw Terminals For Relay (Nc,C,No) And For Input; Coil +, Coil - And Trigger..
【Humanization Design On Interfaces】- All Interfaces Can Be Directly Wired Out Through The Terminals.Fault-Tolerant Design;Fault-Tolerant Design,Even If The Control Line Is Broken, The Relay Will Not Operate..
【Wide Application】-These 5V Relay Board Works Well With Arm /Pic /Avr /Mcu/Raspberry/Cnc Machine/ Ps4 Etc..
【Main Specification】- Peak Load Of No Connector: Ac125~250V/10A, Dc28~30V/10A; Trigger Current: 5Ma;The Module Operating Voltage:12V; 4Pcs * 3.1 Mm Fixed Bolt Hole..
Features
- 5V 1 Channel Relay Module - This Relay Board provides a single relay that can be controlled by any 5V digital output from your microcontroller.
- Main Specification - Peak Load of NO Connector: AC125~250V/10A, DC28~30V/10A; Trigger Current: 5mA;The Module Operating Voltage:12V; 4pcs * 3.1 mm Fixed Bolt Hole.
- Adopted SMD Optocoupler Isolation& jumper Set - The isolation circuit prevent damages to I / O port by relay switch current.The module has a jumper so you can set rather the unit state changes with high or low signal. Has screw terminals for relay (NC,C,NO) and for input; Coil +, coil - and trigger.
- Wide Application -These 5v relay board works well with ARM /PIC /AVR /MCU/Raspberry/CNC machine/ PS4 etc.
- Humanization Design On Interfaces - All interfaces can be directly wired out through the terminals.Fault-tolerant design;fault-tolerant design,even if the control line is broken, the relay will not operate.
- See more on Amazon...
Brand: Youngneer | Manufacturer: Youngneer
Dimensions: 0.01 x 0.02 x 0.01 Inches
See On Amazon #13
GKmow 4 PCS Four-pin Automotive Relay, DC 12V 30A Flame-Retardant Housing Waterproof Starting Relay, Multi-Functional Motor Replacement Accessory, Suitable for Most Models (Black)
Asin: B0CJ99XJR6 | Model: GKJDQ2002BL-4PC-2 | PartNumber: GKJDQ2002BL-4PC-2 | Ean: 0727903812942 | UPC: 727903812942
30A Current Rating: This Relay Has A Current Rating Of 30A, Which Means It Can Handle A Maximum Current Load Of 30 Amps. This Makes It Suitable For Many High-Power Devices Such As Car Starter Motors..
Packing Content: You Will Receive Four Four-Pin Dc 12V 30A Car Starting Relays. If You Have Any Usage Problems, Please Feel Free To Contact Us Directly And We Will Solve The Problem For You Within 24 Hours On Working Days..
Reliability And Durability: It Can Withstand Long-Term, Frequent Use And Maintain Stable Performance In A Variety Of Environmental Conditions. This Car Starter Relay Is Made Of High-Quality Materials And Has Good Reliability And Durability..
Dc 12V Voltage: This Is The Voltage Standard Used By Most Cars, So It Has Broad Applicability. This Relay Is Suitable For Automotive Systems Powered By Dc 12V Power Supply..
Features
- Flame-retardant Shell: This car starter relay is made of flame-retardant shell material and has good flame-retardant properties. This means that in the event of a fire or other dangerous situation, it can effectively reduce the possibility of fire spread and improve the safety of vehicles and passengers.
- DC 12V Voltage: This is the voltage standard used by most cars, so it has broad applicability. This relay is suitable for automotive systems powered by DC 12V power supply.
- 30A Current Rating: This relay has a current rating of 30A, which means it can handle a maximum current load of 30 amps. This makes it suitable for many high-power devices such as car starter motors.
- Reliability and Durability: It can withstand long-term, frequent use and maintain stable performance in a variety of environmental conditions. This car starter relay is made of high-quality materials and has good reliability and durability.
- Packing Content: You will receive four four-pin DC 12V 30A car starting relays. If you have any usage problems, please feel free to contact us directly and we will solve the problem for you within 24 hours on working days.
- See more on Amazon...
Brand: GKmow | Manufacturer: GKmow
Warranty: Manufacturer warranty for 30 days from date of purchase
See On Amazon #14
4 pcs DC 5V 1 Channel Relay Module Board Shield High/Low Level Trigger with Optocoupler
Asin: B079FJSYGY | Model: WJ-00010 | PartNumber: WJ-00010 | Ean: 6941595311734
Smd Optocoupler Isolation, Strong Driving Ability, Stable Performance; Trigger Current 5Ma.
The Module Can Be Set High Or Low Triggered By Jumper.
The Module Voltage 5V.
Maximum Load: Ac 250V/10A, Dc 30V/10A.
Features
- The module uses genuine quality relay, normally open interfaces
- Maximum load: AC 250V/10A, DC 30V/10A
- SMD optocoupler isolation, strong driving ability, stable performance; trigger current 5mA
- The module voltage 5V
- The module can be set high or low triggered by jumper
- See more on Amazon...
Brand: CHENBO | Manufacturer: CHENBO
See On Amazon #15
24 Pcs 5v Relay Module One Channel Relay Switch with Optocoupler 5v Relay Board with Opto Isolation Support High and Low Level Trigger, 19.69 x 10.24 x 7.09 Inch
Asin: B0BG49Z2LD | Model: Kigeli-8876 | PartNumber: Kigeli-8876
Stable And Functional: Equipped With Smd Optocoupler Isolation, Relay Switches Are Powerful In Drive Ability, Safe And Reliable To Use, And They Can Support High Level Or Low Level Triggers, Which Can Well Facilitate Your Use.
Size And Compatibility: 5V Relay 1 Channel Measures About 50 X 26 X 18 Cm/ 19.69 X 10.24 X 7.09 Inches, Convenient For Your Installation And Storage; And They Are Compatible With Pic, Arm, Cnc Machine And So On, Versatile To Use.
Fault Tolerance: Relay Module Is Designed With Good Fault Tolerance, The Relay Doesn't Act Even If The Control Line Is Disconnected, Which Is An Intimate And Thoughtful Design For You; And You Can Connect All Interfaces Through The Wiring Terminal, Saving Time And Effort.
Large Quantity: You Can Receive 24 Pieces Of Relay Boards From The Package, Sufficient In Quantity, Exquisite In Workmanship, Enough For You To Use, Replace And Share With Your Family And Others.
Features
- Product Description: 5v relay module's maximum load of the normally open interface: AC 250V/10A, direct current 30V/10A, with trigger current 5mA; It is featured with stable performance and sensitive reaction to make sure a satisfactory using demands
- Large Quantity: you can receive 24 pieces of relay boards from the package, sufficient in quantity, exquisite in workmanship, enough for you to use, replace and share with your family and others
- Stable and Functional: equipped with SMD optocoupler isolation, relay switches are powerful in drive ability, safe and reliable to use, and they can support high level or low level triggers, which can well facilitate your use
- Fault Tolerance: relay module is designed with good fault tolerance, the relay doesn't act even if the control line is disconnected, which is an intimate and thoughtful design for you; And you can connect all interfaces through the wiring terminal, saving time and effort
- Size and Compatibility: 5v relay 1 channel measures about 50 x 26 x 18 cm/ 19.69 x 10.24 x 7.09 inches, convenient for your installation and storage; And they are compatible with PIC, ARM, CNC Machine and so on, versatile to use
- See more on Amazon...
Brand: Kigeli | Manufacturer: Kigeli
Dimensions: 0.71 x 11.81 x 3.94 inches
See On Amazon #16
Tnisesm/6pcs Coil DPDT PCB Power Relay DC 5V 8 Pins Mini Power Relay PCB Relay HK19F-8P-5V
Asin: B0874MC6D3 | Model: CAHK19F-8P-5V | PartNumber: CAHK19F-8P-5V
Number Of Pins : 8; Size (Approx.) : 2 X 1 X 1.4Cm / 0.8" X 0.4" X 0.6"(L*W*H); Weight : 51G; Package Content : 6 Pcs.
Warranty For 1 Year. If There Are Any Issues With Your Order, Please Contact Us..
Compact And Sealed Construction. Long Operational Life. The Relay Can Automatically Adjust, Protect And Transform The Circuit..
Coil Voltage : Dc5v; Contact Ratings: 1A 125Vac/2A 30Vdc; 2No 2Nc.
Features
- Product Name : PCB Power Relay; Model : HK19F
- Coil Voltage : DC5V; Contact Ratings: 1A 125VAC/2A 30VDC; 2NO 2NC
- Number of Pins : 8; Size (Approx.) : 2 x 1 x 1.4cm / 0.8 x 0.4 x 0.6(L*W*H); Weight : 51g; Package Content : 6 Pcs
- Compact and sealed construction. Long operational life. The relay can automatically adjust, protect and transform the circuit.
- Warranty for 1 year. If there are any issues with your order, please contact us.
- See more on Amazon...
Brand: Tnisesm | Manufacturer: Tnisesm
See On Amazon #17
DaFuRui 5v Relay Module 8Pack 1 Channel Relay Module 5v Relay Board with Optocoupler Support High/Low Level Trigger for Arduino Relay
Asin: B07S48BVK5 | Model: Relay | PartNumber: Relay | Ean: 0738426125136 | UPC: 738426125136
★【Design Features】 Fault-Tolerant Design, Even If The Control Line Breaks, The Relay Will Not Move; With Optical Coupling Isolation, Triggering More Reliable, More Stable..
★【Widely Used】Standard Interface Can Be Directly Connected With Microcontrollers. Apply To Arm、Pic、Avr、Mcu、Raspberry、Cnc Machine And Ps4 Etc..
★【Easy To Install】Equipped With A Terminal Block And Fixed Bolt Holes On Both Sides (Diameter: 3.1Mm), The Interface Can Be Directly Connected Through The Terminal Block..
★【Powerful Function】The Module Can Be Set High Or Low Triggered By Jumper.Module Size：50*25*18.5Mm..
Features
- Excellent Quality Relay Board Maximum load: AC 250V/10A, DC 30V/10A With power and relay action indicator.Trigger current 5mA.
- Powerful Function The module can be set high or low triggered by jumper.Module size 50*25*18.5mm.
- Design Features Fault-tolerant design, even if the control line breaks, the relay will not move; With optical coupling isolation, triggering more reliable, more stable.
- Easy to Install Equipped with a terminal block and fixed bolt holes on both sides (diameter: 3.1mm), the interface can be directly connected through the terminal block.
- Widely Used Standard interface can be directly connected with microcontrollers. Apply to ARM PIC AVR MCU Raspberry CNC machine and PS4 etc.
- See more on Amazon...
Brand: DaFuRui | Manufacturer: DaFuRui
See On Amazon #18
ARCELI 5PCS 5V One Channel Relay Module Board Shield 5v Relay Module for PIC AVR DSP ARM for Relay
Asin: B07BVXT1ZK | Model: 00075 | PartNumber: 00075 | Ean: 0613835617826 | UPC: 613835617826
New 5V Relay Module.
100% Brand New.
This Product Contains 5 Modules.
5V Relay Module 1 Way Relay Module.
Features
- Name: kits module
- 5V relay module 1 way relay module
- New 5V relay module
- This product contains 5 modules
- 100% brand new
- See more on Amazon...
Brand: ICQUANZX | Manufacturer: ARCELI
See On Amazon #19
Huayao 2pcs 8 Channel DC 5V Relay Module with Optocoupler for UNO R3 MEGA 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi
Asin: B08V4YNSYK | Model: HY027 | PartNumber: HY027 | Ean: 0192881982732 | UPC: 192881982732
Brand: Huayao | Manufacturer: Huayao
See On Amazon #20
JBtek 4 Channel DC 5V Relay Module for Arduino Raspberry Pi DSP AVR PIC ARM
Asin: B00KTEN3TM | Model: 4450182 | PartNumber: 4450182 | Ean: 0520361134553 | UPC: 520361134553
Be Able To Control Various Appliances, And Other Equipments With Large Current.
Indication Led's For Relay Output Status.
Application：Supports All Mcu Control, The Industrial Field, Plc Control, Smart Home Control.
5V 4-Channel Relay Interface Board, And Each One Needs 50-60Ma Driver Current.
Features
- Equiped with high-current relay, AC250V 10A ; DC30V 10A
- 5V 4-Channel Relay interface board, and each one needs 50-60mA Driver Current
- Be able to control various appliances, and other equipments with large current
- Application Supports all MCU control, The industrial field, PLC control, Smart home control
- Indication LED's for Relay output status
- See more on Amazon...
Brand: JBtek | Manufacturer: JBtek
Dimensions: 0.79 x 2.56 x 1.97 inches | Weight: 0.02 pounds
See On Amazon
Looking For Something Else?
Search