PWM to Voltage Module 0% -100% PWM Converted to 0-10V Voltage Suitable for Signal Interface Switching for PLC or Other Industrial Control(PWM-to-Voltage 0-10V) (2)
Asin: B0B1J56GR5 | Ean: 0701715534773 | UPC: 701715534773
As an Amazon Associate we earn a fee from qualifying purchases when you follow a link to Amazon from this page. We rank the products, but the links to Amazon are promotional.Widely Used In Signal Interface Switching Of Plc, Single Chip Or Other Industrial Control Board..
Compact Size, Model: 3.3P-5V, Input 0-100% Pwm Signal Of 3.3V Level, Output 0-10V Voltage, Insert The Jump Pin At 5V, The Module Is Easy To Use In Different Places..
Under The Module Size, Easy To Use In Different Places. Embedded Microcontroller Technology. Easy To Operate, You Can Fine-Tune The Potentiometer..
Module Working Voltage: 15-30V Dc (Power Requirement Of Power Supply: >100Ma), Pwm Signal Receiving Frequency Range: 100Hz-3Khz (1-3Khz Is Recommended)..
Features
- Convert 0-100% PWM digital signal into analog signal, Input 0-100% PWM signal of 3.3V level, output 0-10V voltage.
- Module Working voltage: 15-30V DC (power requirement of power supply: >100MA), PWM signal receiving frequency range: 100HZ-3KHZ (1-3KHZ is recommended).
- Widely used in signal interface switching of PLC, single chip or other industrial control board.
- Under the module size, easy to use in different places. Embedded microcontroller technology. Easy to operate, you can fine-tune the potentiometer.
- Compact size, Model: 3.3P-5V, Input 0-100% PWM signal of 3.3V level, output 0-10V voltage, Insert the jump pin at 5V, the module is easy to use in different places.
- See more on Amazon...
Brand: AOICRIE | Manufacturer: AOICRIE
See On Amazon Similar To PWM to Voltage Module 0
#1
RioRand 300W 5-50V PWM DC Brushless Electric Motor Speed Controller with Hall-Less
Asin: B087M3GVYX
The Power Supply On The Main Board, The Power Supply Positive And Negative Pole Is Reversed Will Cause Permanent Damage To Some Of The Chips On The Board (High Current For A Few Seconds Is Not Possible)..
Do Not Connect The Obvious And Drive Module Voltage, Current, Power Phase Does Not Match Or Far From The Motor To Avoid Inexplicable "Nonsense" Damage..
Received The Goods, In The Wiring And Use Of Unclear, Please Contact Us At The First Time To Communicate, Even If There Are Problems With The Use Of The Product, But Also Friendly Consultation Properly Handled..
Motor Output For Sampling Overcurrent Protection, Due To The Module Power Supply Current Are Very Large. Do Not Artificially Cause A Short Circuit In The Normal Operation Of The Module, A Short Circuit Will Damage The Tube. Wiring Test Machine For Small-Current Low-Voltage Test, Successful Then Through The High-Current High-Voltage . Bare Board Module, Pay Attention To Wire Insulation When Wiring, Forbid Strong Voltage To Touch The Board..
Bldc Wide Voltage 5-50V, High Power 300W, Dc Three-Phase High-Speed Brushless Inductor Controller, Speed Control Support Three Signal Inputs, Pwm Signal Input, Plc 0-5V Touch Volume, 1-4.2V Hall Handle Input..
Features
- This driver is DC three-phase brushless Hall-free control board, the motor without Hall can also work normally.
- BLDC wide voltage 5-50V, high power 300W, DC three-phase high-speed brushless inductor controller, speed control support three signal inputs, PWM signal input, PLC 0-5V touch volume, 1-4.2V Hall handle input.
- The power supply on the main board, the power supply positive and negative pole is reversed will cause permanent damage to some of the chips on the board (high current for a few seconds is not possible).
- Motor output for sampling overcurrent protection, due to the module power supply current are very large. Do not artificially cause a short circuit in the normal operation of the module, a short circuit will damage the tube. Wiring test machine for small-current low-voltage test, successful then through the high-current high-voltage . Bare board module, pay attention to wire insulation when wiring, forbid strong voltage to touch the board.
- Do not connect the obvious and drive module voltage, current, power phase does not match or far from the motor to avoid inexplicable nonsense damage.
- Received the goods, in the wiring and use of unclear, please contact us at the first time to communicate, even if there are problems with the use of the product, but also friendly consultation properly handled.
- See more on Amazon...
Brand: RioRand | Manufacturer: RioRand
Dimensions: 1.18 x 2.36 x 1.97 inches
See On Amazon #2
Agatige Handwheel Motion Controller, 5 Axle USB Interface Board CNC Motion Control Card with Handwheel CNC Controller for CNC Router Engraving Machine
Asin: B0D2LJ6BXN
Voltage Output - One-Way Optocoupler-Isolated 0-10V Analog Voltage Output Can Control The Inverter Input From 0-10V Analog Voltage To Control The Spindle Speed, Can Be Used For Many Styles And Types Of Cnc Machines..
4 Output Port - Cnc Stepper Motor Kit Provide 4 Output Port, 5V Leveling, Which Can Be Connected With Photocoupler Relay Module To Control Water Cooling, Spray And So On, Suitable For Lathes, Cnc Routers,Pick And Place And Milling Machine,Lathe Machine..
Pwm Output - Cnc Controller Adopt Pwm Output Is Provided, Which Can Be Connected To The Spindle Governor Controlled By Pwm, Support Various Versions Of Software And Support The Latest Version..
Function - All Input Signals Are Isolated By Optical Diaphragm, Which Can Be Connected To Emergency Stop, Tool Setting, Limit Position, 0 Return, Ensure Computer Security, Input Can Be Connected To A Mechanical Switch Or A Proximity Switch..
Features
- Voltage range - Electrical motor controls has wide external voltage input, 12-24V, and anti-reverse function, provides high control precise for stepper motors and servo motors, perfect for powering fans, small motors, soldering irons.
- Function - All input signals are isolated by optical diaphragm, which can be connected to emergency stop, tool setting, limit position, 0 return, ensure computer security, input can be connected to a mechanical switch or a proximity switch.
- Voltage output - One-way optocoupler-isolated 0-10V analog voltage output can control the inverter input from 0-10V analog voltage to control the spindle speed, can be used for many styles and types of CNC machines.
- PWM output - CNC controller adopt PWM output is provided, which can be connected to the spindle governor controlled by PWM, support various versions of software and support the latest version.
- 4 output port - CNC stepper motor kit provide 4 output port, 5V leveling, which can be connected with photocoupler relay module to control water cooling, spray and so on, suitable for lathes, cnc routers,pick and place and milling machine,lathe machine.
- See more on Amazon...
Brand: Agatige | Manufacturer: Agatige
Dimensions: 2.36 x 9.45 x 3.54 inches | Weight: 2.09 pounds
See On Amazon #3
DROK DC Buck Module, Adjustable Buck Converter Step Down Voltage Regulator 6V-32V 30V 24V 12V to 1.5-32V 5V 5A LCD Power Supply Volt Reducer Transformer Module Board with USB Port Protective Case
Asin: B07JZ2GQJF | Model: 180080AFA | PartNumber: 180080AFA
Display --- Large Clear Digital Lcd Display Voltage & Current Value Simultaneously..
Note --- 1). Output Voltage Is Set As Around 20V By Default, If Your Input Is Lower Than That, Please Turn Potentiometer Anticlockwise For 10 Laps Or More Until Voltage Changes. 2). The Case Is Packaged Unassembled To Avoid Damage During Transit. It Needs To Be Manually Installed. 3). Please Carefully Read The User’S Manual, Especially The “Cautions” Before Using. You Can Find The Pdf Instructions On This Page -- Product Information -- Product Guides And Documents -- User Manual [Pdf]..
Features --- Constant Current/Voltage Mode; Voltage Calibration & Current Calibration; Usb Interface; Protective Case; Short-Circuit Protection; Over-Temperature Protection; Input Reverse Connection Protection..
General Use --- As Ordinary Step-Down Module With Over-Current Protection; As Constant Current Led Driver Module; Diy A Solar Power Controller, Etc..
Features
- PARAMETER --- Input voltage range DC 6V-32V; Output voltage DC 1.5V-32V; Max output current 5A, recommend use of within 4.5A; Max output power 75W, recommend use of within 50W.
- GENERAL USE --- As ordinary step-down module with over-current protection; As constant current LED driver module; DIY a solar power controller, etc.
- DISPLAY --- Large clear digital LCD display voltage & current value simultaneously.
- FEATURES --- Constant current/voltage mode; Voltage calibration & current calibration; USB interface; Protective case; Short-circuit protection; Over-temperature protection; Input reverse connection protection.
- NOTE --- 1). Output voltage is set as around 20V by default, if your input is lower than that, please turn potentiometer anticlockwise for 10 laps or more until voltage changes. 2). The case is packaged unassembled to avoid damage during transit. It needs to be manually installed. 3). Please carefully read the user s manual, especially the Cautions before using. You can find the PDF Instructions on this page -- Product information -- Product guides and documents -- User Manual [PDF].
- See more on Amazon...
Brand: DROK | Manufacturer: DROK
Dimensions: 0.98 x 1.57 x 2.58 inches | Weight: 0.15 Pounds
See On Amazon #4
DROK Waterproof DC Buck Converter Voltage Regulator 8-22V to 3-15V 5V 12V 3A Adjustable Output Power Supply Transformer Step-Down Volt Module Board for Car Auto Vehicle Motor Regulated SR
Asin: B00C0KL1OM | Model: 090010 | PartNumber: 090010 | Ean: 0619397027004 | UPC: 619397027004
Fully Sealed, Outer Enclosure Acts As A Heat Sink, Specially Made To Be Waterproof, Anti-Shock, Anti-Humidity And Dust-Proof, More Durable..
Perfect For Electronic Hobby Project, Wide Application, You Can Use It On Radio, Car Audio, Led Display, Motor, Cell Phone, Etc..
With Reversed-Connection Protection, Over-Current Protection, Over-Heating Protection And Over-Voltage Protection, Hence Is Safe To Use..
With Potentiometer On The Bottom, Which Allows You Adjust The Accuracy With The Mini Screw, But Ensures You Won't Easily Change Its Setting When Mounted..
Features
- Uses synchronous rectification technology, has high conversion efficiency and stable performance; The input should be at least 3V higher than output.
- With potentiometer on the bottom, which allows you adjust the accuracy with the mini screw, but ensures you won't easily change its setting when mounted.
- Fully sealed, outer enclosure acts as a heat sink, specially made to be waterproof, anti-shock, anti-humidity and dust-proof, more durable.
- With reversed-connection protection, over-current protection, over-heating protection and over-voltage protection, hence is safe to use.
- Perfect for electronic hobby project, wide application, you can use it on radio, Car Audio, LED display, motor, cell phone, etc.
- See more on Amazon...
First Available: 05/26/2021
Brand: DROK | Manufacturer: DROK
Dimensions: 0.79 x 1.30 x 0.98 inches | Weight: 0.00 Pounds
Warranty: 1 year
See On Amazon #5
Wolfwhoop PW-D Control Buck Converter 6-24V to 5V 1.5A Step-Down Regulator Module Power Inverter Volt Stabilizer
Asin: B076P4C42B | Model: 5824093032 | PartNumber: 5824093032
It With A Super Mini Size: 17Mm * 5.5Mm.
This Voltage Step Down Module Is Designed For 2-6S Battery.
It Can Power For Transmitter And Receiver Or Mini Camera.
Voltage Buck: 6-24V In, 5V Out..
Features
- 4pcs PW-D
- Voltage buck: 6-24V in, 5V out.
- It with a super mini size: 17mm * 5.5mm
- It can power for transmitter and receiver or mini camera
- This voltage step down module is designed for 2-6S Battery
- See more on Amazon...
Brand: Wolfwhoop | Manufacturer: Wolfwhoop
Weight: 0.02 pounds
See On Amazon #6
DROK Adjustable Voltage Regulator DC, Buck Boost Converter 6.0V-36V 9v 12v to DC 0.6-36V 24v 5A Power Supply Panel, Constant Current Volt Step Up Down Module
Asin: B089ND7PTH | Model: 200517 | PartNumber: 200517
Application --- A Compact And Powerful, On The Go Variable Power Supply Or Led Driver; Diy Lab Power Supply..
Memory Data --- 10 Data Groups Of M0-M9 Can Be Stored. Default Will Be Stored In Data Group M0 And M1/M2 Data Group Can Be Quickly Called Up..
Digital Display --- Input Or Out Voltage, Current, Temperature, Power, Electric Capacity, Electric Quantity, Running Time, Voltage And Current Curve, System And Power Parameters..
Easy To Use --- Allows To Set Volts And Limit The Current, Power On Off And Accurate Voltage Setting Return After Power Down..
Features
- Variable Power Supply --- input voltage range DC 6.0-36V, output voltage range DC 0.6-36V, max output current 5A, max output power 80W.
- Easy to Use --- allows to set volts and limit the current, power on off and accurate voltage setting return after power down.
- Application --- a compact and powerful, on the go variable power supply or LED driver; DIY lab power supply.
- Digital Display --- input or out voltage, current, temperature, power, electric capacity, electric quantity, running time, voltage and current curve, system and power parameters.
- Memory Data --- 10 data groups of M0-M9 can be stored. Default will be stored in data group M0 and M1/M2 data group can be quickly called up.
- See more on Amazon...
Brand: DROK | Manufacturer: DROK
Dimensions: 2.09 x 1.69 x 3.11 inches
See On Amazon #7
HiLetgo 2pcs LM2596 Adjustable DC-DC Step Down Buck Power Convert Module 4.0-40V Input to 1.25-37V Output with LED Voltmeter Display
Asin: B00LSEBYHU | Model: 3-01-0167 | PartNumber: 3-01-0167 | Ean: 0702082654835 | UPC: 702082654835
Output Voltage Range Of 1.25V ~ 37V.
4.0-40V To 1.25-37V Led Voltmeter.
Features
- LM2596 DC-DC Buck Step-down Power Converter Module
- 4.0-40V to 1.25-37V LED Voltmeter
- output voltage range of 1.25V ~ 37V
- See more on Amazon...
Brand: HiLetgo | Manufacturer: HiLetgo
See On Amazon #8
DEVMO 5PCS DC 3v-6v to 400kV 400000V Boost Step-up Power Module High-Voltage Generator
Asin: B07T3XDMH8 | Ean: 0796753378540, 0796753378700 | UPC: 796753378700, 796753378540
★High Pressure Discharge Distance Between: 10 Mm - 20 Mm..
★Wiring: Red And Green Power Connection Red Line:"+" Green Line "-" Output : The Other Side ,Same Color Cable..
★The Output High Voltage Wire Length: 100 Mm.Input Power Cord Length: 100 Mm (The Red Line Is Positive)..
★High Pressure Type: The Type Of Pulse Current.Output Voltage: 400000 V(Please Pay Attention To Safety)..
Features
- input voltage: DC 3 V to 6 V. Input current: 2 A - 5 A.
- High pressure type: the type of pulse current.Output voltage: 400000 v(Please pay attention to safety).
- High pressure discharge distance between: 10 mm - 20 mm.
- The output high voltage wire length: 100 mm.Input power cord length: 100 mm (the red line is positive).
- Wiring: Red and green power connection red line:+ green line - output : the other side ,same color cable.
- See more on Amazon...
Brand: DEVMO | Manufacturer: DEVMO
See On Amazon #9
5Pack LM2596 LM2596S DC-DC Step Down Variable Volt Regulator Input 3.0-40V Output 1.5-35V Adjustable Buck Converter Electronic Voltage Stabilizer Power Supply Module
Asin: B07PDGG84B | Model: NA | PartNumber: NA | Ean: 0682228946256 | UPC: 682228946256
★Easy Work: Convenient To Accurately Adjust The Output Voltage With A Mini Screwdriver..
★Application: Widely Used For Diy Mobile Power, Monitor Power Supply, Power Buggies,Communications Equipment Supply,Etc..
★Features: Thickened Circuit Boards,Short Circuit And Over-Temperature Protection..
★Output: Dc 1.5-35 V Voltage Is Continuously Adjustable, Maximum Output Current Is 3 A..
Features
- Input DC 3-40 V (input voltage must be 1.5 V higher than the output voltage, no boost).
- Output: DC 1.5-35 V voltage is continuously adjustable, maximum output current is 3 A.
- Easy work: convenient to accurately adjust the output voltage with a mini screwdriver.
- Features: Thickened circuit boards,Short circuit and over-temperature protection.
- Application: widely used for DIY mobile power, monitor power supply, power buggies,communications equipment supply,etc.
- See more on Amazon...
First Available: 02/20/2023
Brand: Generic | Manufacturer: Does Not Apply
Warranty: 1 year
See On Amazon #10
4 Pieces Adjustable LM2596S DC-DC Buck Converter Reduced Voltage Regulator Power Module 36V 24V 12V to 5V 2A Voltage Stabilizer with Digital Voltmeter Display
Asin: B081N6WWJS | Model: Frienda-Power Converters-01 | PartNumber: Frienda-Power Converters-01
Easy To Use: With Terminal Block, No Soldering Iron Is Also Convenient To Use, And Retain The Wire Bond Point (The Input Voltage Must Be Higher Than The Voltage To Be Output By 1V Or More).
Nice Design: With 150Khz Internal Oscillation Frequency, Features Low Power Consumption And High Efficiency; When The Output Voltage Cannot Be Adjusted And Is Always Equal To The Input Voltage, Please Turn The Potentiometer Counterclockwise For More Than 10 Turns, And Then Use The Module To Adjust The Voltage Normally; This Is Because When The Module Leaves The Factory, The Default Output Voltage Is About 20V.
Output Current: The Maximum Output Current Can Be As High As 3A, The Recommended Working Current Is About 2A, More Than 2A Plus Heat Sink.
Simple To Operate: The Voltmeter Can Be Turned Off, And The Switch Can Be Turned Off By Pressing And Holding The Switch For More Than 1 Second And Less Than 4 Seconds, Once The Voltmeter Is Turned Off, Simply Press The Switch To Turn On The Voltmeter.
Features
- Product parameters: input voltage is 4.0V - 40V, output voltage is 1.25V - 37V, output current is 2A (normal and stable) and 3A max, conversion efficiency 92% (highest), output ripple under 30mV, switching frequency 150KHz, operating temperature is -45 to 85 degree Celsius
- Simple to operate: the voltmeter can be turned off, and the switch can be turned off by pressing and holding the switch for more than 1 second and less than 4 seconds, once the voltmeter is turned off, simply press the switch to turn on the voltmeter
- Easy to use: with terminal block, no soldering iron is also convenient to use, and retain the wire bond point (the input voltage must be higher than the voltage to be output by 1v or more)
- Output current: the maximum output current can be as high as 3A, the recommended working current is about 2A, more than 2A plus heat sink
- Nice design: with 150KHz internal oscillation frequency, features low power consumption and high efficiency; When the output voltage cannot be adjusted and is always equal to the input voltage, please turn the potentiometer counterclockwise for more than 10 turns, and then use the module to adjust the voltage normally; This is because when the module leaves the factory, the default output voltage is about 20V
- See more on Amazon...
Brand: Frienda | Manufacturer: Frienda
Weight: 0.20 pounds
See On Amazon #11
Valefod 6 Pack LM2596 DC to DC High Efficiency Voltage Regulator 3.2-35V to 1.25-30V Buck Converter DIY Power Supply Step-Down Module
Asin: B076H3XHXP | Model: VA-HW-411 | PartNumber: VA-HW-411 | Ean: 0889328049201 | UPC: 889328049201
【Output Voltage】Dc 1.25V To 30V Voltage Is Continuously Adjustable, Maximum Output Current Is 3A..
【Easy To Diy】Connect To Power Source, Using A Mini Screwdriver To Increase Or Decrease Output Voltage By Adjusting The Screw On The Blue Potentiometer And Monitor Voltage With Multimeter To Get The Needed Voltage, Clockwise To Step Up Voltage And Counterclockwise To Step-Down Voltage. (Factory Default Stays A High Voltage, You Need To Contrarotate About 7-15 Circles Before The Voltage Starts Ramping Down, 1 Circle Means +/- 1V).
【Mini Size】45 * 23 * 14 Mm (With Potentiometer). 6Pcs Included..
【Input Voltage】Dc 3.2V To 35V (Input Voltage Must Be 1.5V Higher Than The Output Voltage, No Boost)..
Features
- High Precision The buck converter consists of 36u thickened circuit boards, high-Q inductance with output LED indicator, and superior solid-state capacitors that can effectively filter out high frequency noise. Suitable for various electronic projects.
- Input Voltage DC 3.2V to 35V (input voltage must be 1.5V higher than the output voltage, no boost).
- Output Voltage DC 1.25V to 30V voltage is continuously adjustable, maximum output current is 3A.
- Mini Size 45 * 23 * 14 mm (with potentiometer). 6pcs included.
- Easy to DIY Connect to power source, using a mini screwdriver to increase or decrease output voltage by adjusting the screw on the blue potentiometer and monitor voltage with multimeter to get the needed voltage, clockwise to step up voltage and counterclockwise to step-down voltage. (Factory default stays a high voltage, you need to contrarotate about 7-15 circles before the voltage starts ramping down, 1 circle means +/- 1V)
- See more on Amazon...
Brand: Valefod | Manufacturer: Valefod
Dimensions: 0.55 x 0.90 x 1.77 inches | Weight: 0.03 Pounds
See On Amazon #12
Adjustable DC Power Voltage Converter with Digital Display AC 110V-220V to DC 0-48V Module Switching Power Supply 480W Voltage Regulator Transformer Built in Cooling Fan
Asin: B0CB7NPB6P
Led Display Shows You Real-Time Voltage, Which Makes It More Convenient For You To Adjust Voltage..
Widely Used In Industrial Automation, Radio, Broadcasting, Led Display, Communications, Security Cameras, Lighting, Computer..
Built-In Cooling Fan, Over Temperature Protection, Overheating Automatic Shutdown Protection..
Made Of High Quality Metal,Which Is Durable And Long Last.Note: Before Using, Please Select The Input Voltage 110V/220V According To Your Local Voltage, To Avoid Damaging, Switch Is At Right Side Of The Item..
Features
- Over load protection, over voltage protection, short circuit protection, this protection will protect your load well. Input: AC110-220V, Output: DC 0-48V adjustable, Maximum output current: 10A.
- Made of high quality metal,which is durable and long last.NOTE: before using, please select the input voltage 110V/220V according to your local voltage, to avoid damaging, switch is at right side of the item.
- LED display shows you real-time voltage, which makes it more convenient for you to adjust voltage.
- Built-in cooling fan, over temperature protection, overheating automatic shutdown protection.
- Widely used in Industrial automation, Radio, Broadcasting, LED display, communications, Security cameras, Lighting, Computer.
- See more on Amazon...
Brand: Titoe | Manufacturer: Titoe
See On Amazon #13
Valefod 3 Pack LM2596 DC to DC Voltage Regulator 4-40V to 1.5-35V Buck Converter with LED Display
Asin: B07WQJ2GD6 | Model: VA-0162-BL | PartNumber: VA-0162-BL | Ean: 0793118392197 | UPC: 793118392197
【Output Voltage】Dc 1.5V To 35V Voltage Is Continuously Adjustable, Maximum Output Current Is 3A..
【Easy To Diy】Connect To Power Source, Using A Mini Screwdriver To Increase Or Decrease Output Voltage By Adjusting The Screw On The Blue Potentiometer And Monitor Voltage With Multimeter To Get The Needed Voltage, Clockwise To Step Up Voltage And Counterclockwise To Step-Down Voltage. (Factory Default Stays A High Voltage, You Need To Contrarotate About 7-15 Circles Before The Voltage Starts Ramping Down, 1 Circle Means +/- 1V).
【Mini Size】57*36*13 Mm (With Potentiometer). 3Pcs Included..
【Input Voltage】Dc 4V To 40V (Input Voltage Must Be 1.5V Higher Than The Output Voltage, No Boost)..
Features
- High Precision The buck converter consists of 36u thickened circuit boards, high-Q inductance with output LED indicator, and superior solid-state capacitors that can effectively filter out high frequency noise. Suitable for various electronic projects.
- Input Voltage DC 4V to 40V (input voltage must be 1.5V higher than the output voltage, no boost).
- Output Voltage DC 1.5V to 35V voltage is continuously adjustable, maximum output current is 3A.
- Mini Size 57*36*13 mm (with potentiometer). 3pcs included.
- Easy to DIY Connect to power source, using a mini screwdriver to increase or decrease output voltage by adjusting the screw on the blue potentiometer and monitor voltage with multimeter to get the needed voltage, clockwise to step up voltage and counterclockwise to step-down voltage. (Factory default stays a high voltage, you need to contrarotate about 7-15 circles before the voltage starts ramping down, 1 circle means +/- 1V)
- See more on Amazon...
Brand: Valefod | Manufacturer: Valefod
Dimensions: 0.50 x 1.40 x 2.20 inches
See On Amazon #14
HiLetgo 5pcs DC-DC Buck Step Down Module 6-20V 12V/20V to 5V 3A USB Charger Module
Asin: B01HXU1C6U
Compatible To Arduino.
Dc-Dc Module.
Brand: HiLetgo | Manufacturer: HiLetgo
See On Amazon #15
DROK DC 12V to 5V Buck Converter, 10pcs Mini Voltage Regulator Board DC 4.5-20V 12V 9V Step Down to 1-16V 5V Reducer 3A Fixed Adjustable Volt Output Transformer Power Supply Stabilizer Module
Asin: B08Q3TKJH5
High Efficiency --- Big Energy In Small Size. The Conversion Efficiency Of This Volt Transformer Can Be Up To 97% (Typical Value: >90% When Step Down 12V To 5V 2A)..
Note --- This Mini Buck Converter Is Really Very Tiny, Much Smaller Than A 1-Dollar Coin, Nearly A Half Of The Coin..
Protection And Enable Control --- The 12V Buck Converter Is Designed With Output Short Circuit Protection, But Please Do Not Keep Short Circuit For A Long Time. Also, The Reducer Is Equipped With An Integrated Enable Port Which Defaults The Working Mode That It Will Be Off When It Is At Low Electric Level Off, Which Bring A Great Convenience For Users..
Output Voltage Adjustable Or Fixable --- The Tiny Buck Converter Board Can Be Changed To Adjustable Output Voltage Or A Fixed One. The Reducer Is Default To Be Used For Adjustable Voltage Output. If You Want To Get Fixed Voltage Output, You Need To Cut Off The Pad A By Using A Sharp Thing Such As A Knife, Then Weld Together The Port Of The Fixed Voltage You Want..
Features
- Parameter --- For DROK 5V volt step down regulator: Input voltage: DC 4.5-20V; Output voltage can be adjustable or fixed. Adjustable range: 1-16V; Fixed voltage: 1.8V, 2.5V, 3.3V, 5V, 9V, 12V; Output current: Max 3A (peak: 3A, long-term: within 2A); Power: 10W.
- Output Voltage Adjustable or Fixable --- The tiny buck converter board can be changed to adjustable output voltage or a fixed one. The reducer is default to be used for adjustable voltage output. If you want to get fixed voltage output, you need to cut off the Pad A by using a sharp thing such as a knife, then weld together the port of the fixed voltage you want.
- High Efficiency --- Big energy in small size. The conversion efficiency of this volt transformer can be up to 97% (typical value: >90% when step down 12V to 5V 2A).
- Protection and Enable Control --- The 12V buck converter is designed with output short circuit protection, but please do not keep short circuit for a long time. Also, the reducer is equipped with an integrated enable port which defaults the working mode that it will be off when it is at low electric level off, which bring a great convenience for users.
- NOTE --- This mini buck converter is really very tiny, much smaller than a 1-dollar coin, nearly a half of the coin.
- See more on Amazon...
Brand: DROK | Manufacturer: DROK
Weight: 0.04 Pounds
See On Amazon #16
NOYITO AC to DC Precision Buck Power Supply Module AC 120V 100V-264V to 12V 2A 2000mA Isolated Step Down DC Module (12V 2A) Green
Asin: B07FNFJTHH | Model: NOADPB122 | PartNumber: NOADPB122 | Ean: 0667797751791 | UPC: 667797751791
Output Voltage: 12V ±1%. Output Current: 2A 2000Ma ..
Size: 87 X 46 X 25 Mm (Lwh)..
Ripple: Less Than 60Mvp-P. Output Accuracy: +/-1%. Voltage Regulation Rate: +/-1%..
Input Voltage Range: Ac 120V 100- 264V. Frequency Range: 47-63Hz..
Features
- Isolated Precision Buck Power Supply Module Wide voltage range input with overload, short circuit, over temperature protection. Ultra-small size and high efficiency.
- Input voltage range: AC 120V 100- 264V. Frequency range: 47-63Hz.
- Output voltage: 12V 1%. Output current: 2A 2000mA .
- Ripple: less than 60mVp-p. Output accuracy: +/-1%. Voltage regulation rate: +/-1%.
- Size: 87 x 46 x 25 mm (LWH).
- See more on Amazon...
Brand: NOYITO | Manufacturer: NOYITO
Dimensions: 0.98 x 3.43 x 1.85 inches | Weight: 0.17 pounds
Warranty: Manufacturer's One-year After-sale Warranty
See On Amazon #17
Maxmoral 2pcs DC-DC Buck Converter Power Module 3A Adjustable Step-Down LM2596 Voltage Regulator 24V to 12V 5V 3V
Asin: B07MKQXNWG | Model: LM2596-3A-2 | PartNumber: LM2596-3A-2 | Ean: 0732661152872 | UPC: 732661152872
High Precision Potentiometer, Factory Default Is Approx 18V. Turn The Potentiometer Counterclockwise 1 Cycle, It May Step-Down Approx 1V Voltage..
Two Wire Connection Mode: Solder And Welding Pin..
0.1Uf High Frequency Bypass Capacitor, Can Effectively Filter Out High Frequency Noise..
Adopting Sanyo Solid-State Capacitor, 36U Thickened Circuit Board, High Q Value Large Power Inductance, With Led Indicator..
Features
- Input Voltage: DC 3V-35V, Output Voltage: DC 1.25V-35V (continuously adjustable), high effeciency, max output current up to 3A.
- Adopting SANYO solid-state capacitor, 36u thickened circuit board, high Q value large power inductance, with LED indicator.
- High precision potentiometer, factory default is approx 18V. Turn the potentiometer counterclockwise 1 cycle, it may step-down approx 1V voltage.
- 0.1uF high frequency bypass capacitor, can effectively filter out high frequency noise.
- Two Wire Connection Mode: Solder and Welding Pin.
- See more on Amazon...
Brand: Maxmoral
Weight: 0.10 Pounds
See On Amazon #18
U3-HV USB DAQ Device with 4 Dedicated High-Voltage ( 10V) Analog Inputs, 12 Flexible I/O for Analog and Digital Data Acquisition of Sensors, Controlling Relays, Automation and Timers
Asin: B001716LD6 | Model: U3-HV | PartNumber: U3-HV | Ean: 0689076273862 | UPC: 689076273862
4 High-Voltage Data Logger Analog Inputs And 12 Flexible I/O (Digital Input, Digital Output, Or Lv Analog Input).
Includes Free Software & Support For Life, 5 Years Warranty, Documentation And Datasheet Written By Us Engineers Who Designed The Device.
Up To 2 Timers (Pulse Counting/Timing, Pwm Output, Quadrature Input).
The Data Logger U3 Series Is A Versatile Product For Precise Measurement And Control Within Simple Analog And Digital Systems..
Features
- USB DAQ real time module device with 4 dedicated high-voltage analog inputs, 12 flexible I/O, and 4 dedicated digital I/O. The flexible I/O can be configured as either digital or analog, thus providing up to 16 analog inputs, or up to 16 digital I/O. It also has two 10-bit analog outputs, up to 2 counters, and up to 2 timers.
- The data logger U3 series is a versatile product for precise measurement and control within simple analog and digital systems.
- 4 High-voltage data logger Analog Inputs and 12 Flexible I/O (Digital Input, Digital Output, or LV Analog Input)
- Up to 2 Timers (Pulse Counting/Timing, PWM Output, Quadrature Input)
- Includes Free Software & Support for Life, 5 Years Warranty, Documentation and Datasheet written by US Engineers who designed the device
- See more on Amazon...
Brand: LabJack | Manufacturer: LabJack
Dimensions: 1.20 x 3.00 x 4.50 inches
See On Amazon #19
DROK Buck Converter 12v to 5v, Voltage Regulator Board DC 6.5-36V 24v Step Down to DC 1.2V-32V 12 v Volt Transformer Reducer 4.5A 75W CC CV Power Supply Module
Asin: B07FL6PBZF | Model: 200359 | PartNumber: 200359
Lcd Display: The Step Down Module Is Designed With Lcd, Can Display Input And Output Voltage, Output Current And Output Power; Voltage Display Resolution Is 0.05V, Current Display Resolution Is 0.005A. Please Note That The Volt Display Accuracy Is ±0.1V, The Current Display Accuracy Is ±0.05A..
Note: To Avoid Damage Caused By Collision During Shipping, The Case Is Not Installed When We Package, It Is Packed As Parts. Please Install It After Receiving..
Protection: Our Power Supply Is With Reverse Connection Protection At The Input Terminal, Please Kindly Note That No Anti-Backflow Protection At The Output Terminal; With Crystal Protection Case, Protect The Module From Damaging..
Button Control: The Voltage Regulator Board Is Designed With Button, You Can Easily Set The Output Voltage Without Using Flat Screwdriver; The Button Control Output Voltage On / Off Status, And You Can Set The Default Output State Is On Or Off Of The Next Time Power-On..
Features
- DROK buck converter input voltage range is DC 6.5V-36V; output voltage range is DC 1.2V-32V, factory default output 5V; can work stably at 3.5A for a long time, and can reach 4.5A under the heat dissipation (adjustable current limit is about 4.2-4.5A).
- Button Control: the voltage regulator board is designed with button, you can easily set the output voltage without using flat screwdriver; the button control output voltage ON / OFF status, and you can set the default output state is ON or OFF of the next time power-on.
- LCD Display: the step down module is designed with LCD, can display input and output voltage, output current and output power; voltage display resolution is 0.05V, current display resolution is 0.005A. Please note that the volt display accuracy is 0.1V, the current display accuracy is 0.05A.
- Protection: our power supply is with reverse connection protection at the input terminal, please kindly note that NO Anti-backflow protection at the output terminal; with crystal protection case, protect the module from damaging.
- Note: To avoid damage caused by collision during shipping, the case is not installed when we package, it is packed as parts. Please install it after receiving.
- See more on Amazon...
Brand: DROK | Manufacturer: DROK
Weight: 0.18 pounds
See On Amazon #20
NOYITO 170W High-power H-bridge Motor Drive Module 2-Channel PWM Inputs 0-100% Duty Cycle with Instantaneous Braking Capability Forward Reverse Support 3.3V 5V Logic input Analog input MCU IO Port
Asin: B082VS65BZ | Ean: 0680613663856 | UPC: 680613663856
Supports 3.3V And 5V Logic Inputs. It Is Suitable For Mcu Io Ports To Directly Control The Motor, And It Can Also Control The Motor's Forward And Reverse Rotation Through Analog Input..
Https://1Drv.Ms/U/S!Alzqucoyzqhkggdgtmoexd0-Jmlb?E=2Rveoz.
Suitable For 5-40V Motor.（The Second Picture On The Left Is The Wiring Diagram）.
Noyito 170W High-Power H-Bridge Motor Drive Module User Manual Schematics Wiring Diagram.
Module Working Voltage : 10V-30V. Power: 170W Max..
2-Channel Pwm Inputs, The Duty Cycle Can Be Adjusted Between 0-100%, With Instantaneous Braking Capability..
Features
- NOYITO 170W High-power H-bridge Motor Drive Module is composed of H-bridge driver IC and 4 low-pass internal resistance 55V 110A NMOS tubes. It has the characteristics of small heat generation and good motor braking effect.
- 2-Channel PWM inputs, the duty cycle can be adjusted between 0-100%, with instantaneous braking capability.
- Supports 3.3V and 5V logic inputs. It is suitable for MCU IO ports to directly control the motor, and it can also control the motor's forward and reverse rotation through analog input.
- Module working voltage : 10V-30V. Power: 170W max.
- Suitable for 5-40V motor. The second picture on the left is the wiring diagram
- NOYITO 170W High-power H-bridge Motor Drive Module User Manual Schematics Wiring Diagram
- https://1drv.ms/u/s!AlzQUCOyZQhKggdGTmoExd0-JMLB?e=2rVeoZ
- See more on Amazon...
Brand: NOYITO | Manufacturer: NOYITO
Dimensions: 0.83 x 2.66 x 1.53 inches | Weight: 0.05 Pounds
Warranty: 1 year
See On Amazon
Looking For Something Else?
Search