AURSINC - Buying Guide

Bestselling from AURSINC on Amazon

1. [Upgraded] AURSINC NanoVNA-H Vector Network Analyzer 10KHz -1.5GHz Latest HW Version 3.6 | HF VHF UH...
2. AURSINC NanoVNA-H4 Vector Network Analyzer, Lastest V4.3 10KHz-1.5GHz HF VHF UHF 4" Touch Screen Nan...
3. Portable Tinysa Spectrum Analyzer, AURSINC V0.3.1 Handheld Frequency Analyzer, Signal Generator 100k...
4. AURSINC TinySA Ultra Spectrum Analyzer 4inch - HW V0.4.5.1 100kHz-5.3GHz Handheld Frequency Analyzer...
5. AURSINC NanoVNA Vector Network Analyzer, 10KHz-1.5GHz HF VHF UHF Antenna Analyzer Ham Radio with 2.8...
6. AURSINC NanoVNA-F V2 Vector Network Analyzer, 50KHz-3GHz Antenna Analyzer Ham Radio HF VHF UHF 4.3in...
7. AURSINC Filter Attenuator, RF Demo Kit NanoVNA RF Tester Board for NanoVNA-H NanoVNA-F Vector Networ...
8. Testboard Kit NanoVNA Antenna Analyzer, AURSINC Test Demo Set Tool Compatible with DIP Quickly Assem...
9. AURSINC TinySA Ultra Spectrum Analyzer 4inch - V0.4.5.1 100kHz-5.3GHz Handheld Frequency Analyzer, 2...
10. AURSINC SMA Calibration Kit for NanoVNA H H4 F V2 V3 SAA Mini1300 PS100 Vector Network Analyzer Ante...

Features

• [UPGRADED NanoVNA-H] New HW Version V3.6. It is upgradeable as new firmware is developed. With MicroSD card port now can have the measurement data or the screenshots saved in the it at anytime. Added battery circuit management, more secure. Redesigned PCB, you can connect to mobile phone with Type C-Type C cable (original PCB needs OTG cable), see a clear HD image on your phone. Added a ABS case, which is protective and dust-proof. Disply: 2.8 inch TFT (320 x240)
• [IMPROVED FREQUENCY ALGORITHM] The improved frequency algorithm can use the odd harmonic extension of si5351 to support the measurement frequency up to 1.5GHz. The 50K-300MHz frequency range of the si5351 direct output provides better than 70dB dynamic, The extended 300M-900MHz band provides better than 60dB of dynamics, and the 900M-1.5GHz band is better than 40dB of dynamics
• [MULTIPLE FUNCTIONS] The default firmware main function is used for antenna performance measurement. The TX/RX method can measure the complete S11 and S21 parameters. If you need to obtain S12 and S22, you need to manually replace the transceiver port wiring. The CH0 output level is increased to 0dBm when using the fundamental wave, resulting in more accurate reflection measurement
• [SUPPORT ANDROID PHONE & PC SOFTSARE CONTROL] Designed a practical and simple control application on PC, you can download touchstone(SNP) files for radio design and simulation software. There is a PC interface that adds functionality and lets you work interactively on a bigger screen. Supports time domain analysis function (TDR). Compatible with most Android mobile phones, convenient for connecting to mobile phones. Support Windows Computer Control
• [STRONG AND SECURE POWER SUPPLY] This VNA is battery powered or USB powered. Built in 650mAh battery, could work for 2 hours continuously. For longer measurement time, kindly connect an external power source. The product interface displays battery usage, providing a clear understanding of the power status
• See more on Amazon...

Features

• UPGRADED NANOVNA-H4 V4.3 AURSINC nanovna h4 is a Hugen Origin that provides perfect vector network measurement capabilities, tiny and handheld, stand-alone with 4inch LCD display, with 1950mAh battery powered or USB powered. With latest HW 4.3 version, Nanovna-h4 antenna analyzer is added a brand new panel plus added a new SD port for data storage(support up to 32GB memory card, not included in the package)
• IMPROVED FREQUENCY ALGORITHM The improved frequency algorithm of nano vna h4 can use the odd harmonic extension of si5351 to support the measurement frequency up to 1.5GHz. The 50K-300MHz frequency range of the si5351 direct output provides better than 70dB dynamic. The extended 300M-900MHz band provides better than 60dB of dynamics, and the 900M-1.5GHz band is better than 40dB of dynamics. Used it to check out new cable or antenna installations and to routinely adjust the RF tuner for optimum
• ANTENNA PERFORMANCE MEASUREMENT The default firmware main function for vector network analyzer is used for antenna performance measurement. It has good RF performance for S-parameter measurements as previous models. NOTE: the Nanovna is only compatible with the low-speed and supports SPI mode SD cards for now. It is very efficient vector testing for ham radio operator, research electrical engineer and antenna builders
• PC & ANDROID CONTROL Using PC software NanoVNASaver, NanoVNA-H4 antenna analyzer can connect to a NanoVNA and extracts the data for display on a computer, and for saving to Touchstone files. We can export Touchstone (snp) files for various radio design and simulation software through PC software. The TX/RX method can measure the complete S11 and S21 parameters. If you need to obtain S12 and S22, you need to manually replace the transceiver port wiring
• WHAT ARE INCLUDED 1x NanoVNA-H4 host (with 1950mAh battery), 4pcs SMA male calibration kit (open/short/load/SMA female to female connector), 2x 16cm/6.3inch SMA male to male RG174 RF cable, 1x USB Type-C data cable, 1x Type-C to Type-C cable, 1x Lanyard with stylus, 1x stylus pen, 1x User Manual
• See more on Amazon...

Features

• [Upgraded Version: ESD Protection Diodes] - Tinysa produced by Hugen, with V0.3.1 hardware. The firmware of the tinySA can be updated, for newest firmware version update, please refer to: tinysa .org. The displayed version info indicates "ESD protection" with a diode for improved stability, sensitivity, anti-static level and longevity
• [Frequency Range] - The tinysa spectrum analyzers use a resolution filter to isolate input power within a narrow frequency range. This resolution filter is swept across the desired frequency range. The fastest scanning speed occurs with an RBW or 300kHz or wider and is about 2 scans per second. The scanning speed decreases rapidly as the frequency span increases and the RBW decreases. A scan from 0MHz to 350MHz with an RBW of 10kHz takes about 2 minutes
• [2 in 1 Device] - When not used as Spectrum Analyzer it can be used as Signal Generator, MF/HF/VHF sinus output between 0.1MHZ-350MHz, UHF square wave output between 240MHz-960MHz. Built-in calibration signal generator enables automatic self-test and low input calibration. The tinysa includes all the components of a traditional heterodyne swept spectrum analyzer, with a color display showing 290 scan points covering up to the full low or high frequency range
• [4 Input/Output Spec Modes] - The input/output spec of the tinysa is divided into 4 modes: Low Input, High Input, Low Output, and High Output. Spectrum Analyzer has two inputs: high-quality MF/HF/VHF input for 0.1MHz-350MHz; lower-quality UHF input for 240MHz-960MHz. Switchable resolution bandpass filters ranging from 2.6kHz to 640kHz
• [PC Control] - The USB interface realizes the Serial over USB (CDC) protocol and a large number of commands can be called through the serial interface. The commands can be used for measurements or updating internal settings. The Windows driver will automatically install upon connecting to a Windows PC. The driver for Linux is built into the kernel. Tinysa-APP is available to control the tinysa and capture its screen.
• [Package List] - 1x Tiny sa Spectrum Analyzer(with 500mah battary, 2.8inch touchsreen) ; 2x 20cm/7.87inch RF Cable; 1x USB-C Cable ; 2x SMA Female to Female Connector; 1x Touchscreen Pen; 1x SMA Telescopic Antenna. Reliability you can trust, our spectrum analyzer caters to your diverse needs.
• See more on Amazon...

Features

• [Upgrated Frequency Analyzer] - AURSINC tinysa ultra developed by Hugen, hardware version V0.4.5.1. Now have new hardware system V0.4.5.1.1 - Updated LCD screen for availability reasons. With the new ESD protection function, the product has a higher anti-static level and a longer service life. Linear power supply to avoid switching noise
• [Widely Frequency Range] - Tiny SA Ultra has an ultra wide measuring frequency range of 100kHz to 5.3GHz, spectrum analyzer for 100kHz-800MHz and Ultra mode up to 6GHz, can observe signals up to 12GHz. Switchable resolution bandpass filters from 200Hz to 850kHz, you could fast and accurate execute measurement tests
• [2 in 1 Device] - When not used as Spectrum Analyzer it can be used as Signal Generator, MF/HF/VHF sinus output between 100kHZ-800MHz, UHF square wave output between 800mHz-4.4GHz, Mixing signal output is between 4.4GHz-5.4GHz. Built-in calibration signal generator that is used for automatic self test and low inputcalibration
• [Intuitive Controls] - With 4 inch touch screen (480*320 pixels resolution), providing clear data images and sensitive operation touch. Color display showing max 450 points providing gapless covering up to the full frequency range. This displays frequencies all the up to the ranges of 5.2 GHz WiFi and is a great way to visually identify where to put your access points, or if your faraday shielding is effective
• [PC Operation] - This spectrum analyzer can connect to a PC via USB, realize the USB serial (CDC) protocol, and can be invoke a large number of commands through the serial interface. These commands can be used to perform measurements or update internal Settings. Built-in Linux drivers, Windows drivers are automatically installed when connected to a Windows PC. Tinysa-APP directly transfers data to the computer
• See more on Amazon...

Features

• [Designed for DIY] This nanovna is a DIY product (no enclosure) that provides perfect vector network measurement capabilities in a credit card-sized design, featuring a 2.8-inch TFT touch screen (320 x240) and a 650mAh battery for up to 2 hours. Added battery management circuit to reduce power noise, USB power interference, charging current, and protects the battery
• [Licensing and Firmware] Developed by Hugen, more info pls view nanovna-users@groups.io. The firmware version of nano vna is HW V3.5. It is upgradeable as new firmware is developed (github.com/ttrftech/NanoVNA). The default firmware of AURSINC nanovna main function is used for antenna performance measurement
• [Measurement Frequency] Measurement frequency of nanovna is 10KHz - 1.5GHz (50KHz -900MHz, enable extended firmware). Measurement range: 70dB (50kHz-300MHz), 60dB (300M-900MHz), 40dB (900MHz-1.5GHz) enable extended firmware. The improved frequency algorithm can use the odd harmonic extension of si5351 to support the measurement frequency up to 1.5GHz
• [PC Control] Designed a practical and simple control application on PC, you can download touchstone(SNP) files for radio design and simulation software. There's NANOVNASHARP software available for PC and Linux (github.com/mihtjel/nanovna-saver/releases), supports control and real-time display. You can connect the nanovna to your PC for a large screen display with a USB-C cable
• [Accurate Measurement] The TX/RX method can measure the complete S11 and S21 parameters. If you need to obtain S12 and S22, you need to manually replace the transceiver port wiring. The CH0 output level is increased to 0dBm when using the fundamental wave, resulting in more accurate reflection measurement
• [More Functionality] Measuring amplifier gain, bandwidth, phase frequency characteristics, transmission line loss, characteristic impedance, coupler coupling, isolation, filter, diplexer passband and so on. You can being able to see a graph of the SWR of a given antenna over a sweep that you get to set start and stop. Excellent performance for radio amateurs
• [Package list] 1x NanoVNA host (with 650mA-h battery, without case, came in a plastic case), 1x USB Type-C data cable, 2x 30cm SMA male to male RG174 RF cable, 1x SMA simple calibration kit, 1x SMA female to female connector
• See more on Amazon...

Features

• [Upgraded Version] The NanoVNA-F V2 upgraded to the latest firmware V0.4.0, the operation page is compatible with Nanovna-F. More features that it enables measurements of S-parameter, voltage standing wave ratio (SWR), phase map, group delay, Smith chart, DELAY, POLAR, LINEAR and more
• [Frequency Range] The measurement range of nanovna-f v2 expanded to 50KHz-3GHz. The TX/RX method can measure the complete S11 and S21 parameters, S21 dynamic ranges: 70dB (1.5GHz), 60dB (3GHz); S11 dynamic ranges: 50dB (1.5GHz), 40dB (3GHz)
• [Design of Aluminum Cases] Rugged and durable aluminum alloy cases, shielding electromagnetic interference to ensure precise measurements. The SMA radio frequency interface enables seamless connectivity with various measurement devices
• [4.3'' Screen & 5000mAh Battery] The nano vna has a 4.3-inch IPS TFT LCD screen with a resolution of 800*480 and a resistive touch screen, providing a large viewing angle. It is equipped with an 5000mAh lithium battery for longer standby time, up to 7 hours of usage. With the use of a 2A large-current charging IC, the charging time is reduced. As an add-on, it built-in 5V output for charging Android phones or tablets
• [PC & Android Phone Control] NanoVNA F V2 hardware is supported by a program NanoVNA Saver, using Nanovna-Saver connect to the nanovna, extracts data for display and save data in Touchstone files. The SCADA software enables us to export Touchstone (snp) files for various radio design and simulation software. Supports Android Mobile Phone only (Please download the product document for details)
• [NanoVNA Saver Notes] it could run on windows 7 embedded control system with your own software. For Win8 and earlier versions of the Windows system, you need to install the driver: st.com/en/development-tools/stsw-stm32102.html. For NanoVNA-Saver you need to try, we do not support any win10 earlier versions system. Software Upgrade the website: sysjoint.com/en/content/?144.html. Any questions please contact us.
• [Packing List] 1x Nanovna f v2 Host, 1x SMA Open Calibration Kit, 1x SMA Short-circuit Calibration Kit, 1x SMA 50 Load Calibration Kit, 1x SMA-KK Double-Head Female Hole Adapter, 1x SMA-JJ Double-Head Male Pin Adapter, 1x SMA-JKW Elbow Outer Screw Inner Hole To Inner Screw Inner Needles Adapter, 2x 20cm SMA-JJ RG405 RF Cable, 1x USB Type-C Data Cable, 1x Stylus
• See more on Amazon...

Features

• [Evaluating and Learning Nanaovna] The RF Demo Kit is a NanoVNA RF test board independently designed by BH5HNU, with a size of 10*10cm / 3.94*3.94 inch. The demo calibration board for evaluating and learning nanaovna vector network analyzer, antenna analyzer test calibration learning, making sure your setup is working
• [Tiny but Mighty] This RF Demo Kit is integrated with 18 functional modules. Can be used to measure 30MHz short wave low-pass-filter LPF, 100MHz FM high-pass filter HPF, 433MHz commonly used SAW band pass filter BPF, 6.5MHz ceramic trap BSFtt
• [Note] The test parameters of the 18 patterns of the test board are described as follows. Two steps must be performed before testing: Step 1. Connect the two 20CM SMA to IPEX adapter cables to the NanoVNA-F machine. Step 2. Recalibrate the machine using the 13 Short, 14 Open, 15 Load, and 16 Thru circuits on the test board, and save the parameters to SAVE 0
• [Applicability] It works with Nanovna-h / Nanovna-h4 / Nanovna-f / f v2 / f v3 / Nanovna saa-2n, and other nanovna antenna analyzer
• [Package Included] 1x PCB RF tester board, 2 x 20cm U.FL connectors (Be aware the connectors on the test cables that connect to the PCB are only good for a hand-full of connection/disconnection cycles before they break)
• See more on Amazon...

Features

• The Testboard kit allows NanoVNA users to assemble a useful Component jig to quickly assemble a simple RF circuit and evaluate their performance on the NanoVNA
• This test board contains a plug-in test circuit suitable for VNA Testboard, and a set of 0805 and 1206 patch test circuits are added
• The testboard kit is utilized for user-friendly measurement of DIP and SMT devices with NanoVNA or other vector analyzers
• Product come unassembled, you need to assemble according to your purpose. Please prepare your own welding tools and build a test circuit according to your test needs. We are not responsible for circuit guidance
• The SMT circuit cannot fully consider all test conditions. Some tests may need to be cut over. Please ensure you have sufficient practical skills
• Package include: 1x Testboard Printed Circuit Board (Compatible with DIP pads of VNWA Testboard and add 0805 and 1206 STM pads), 6x SMA End Connectors (same type as in NanoVNA), 4x Copper 8mm spacers, 4x M2.5 4mm screws, 2x 40 pin female SIL Socket
• See more on Amazon...

Features

• [Upgraded TinySA Ultra] Tinysa Ultra developed by Hugen, HW V0.4.5.1. With 4inch touch screen(480*320 pixels resolution), tinysa ultra spectrum analyzer has ultra measurement range from 100kHz to 5.3GHz, built-in 32Gb micro SD card for data transfer and storage. Linear power supply to avoid switching noise
• [Frequency Range] Tiny sa ultra measures from 100KHz-5.3GHz: Spectrum Analyzer for 0.1MHz-800MHz, with Ultra mode enabled, level calibrated up to 6GHz, can observe signals up to 12GHz. Switchable resolution bandpass filters from 200Hz-850kHz. You can fast and accurate execute measurement tests
• [PC Operation] Connected to a PC via USB. The USB interface implements CDC protocol and there is a large set of commands that can be invoked over the serial interface. These command can be used to perform MEAS or update internal settings. Tinysa-APP transfers data directly to the computer. The driver for Windows will install automatically after connecting to a Windows PC. The driver for Linux is built into the kernel
• [2 in 1 Device] When not used as Spectrum Analyzer it can be used as Signal Generator, MF/HF/VHF sinus output between 100kHZ-800MHz, UHF square wave output between 800mHz-4.4GHz, Mixing signal output is between 4.4GHz-5.4GHz. Built-in calibration signal generator that is used for automatic self test and low inputcalibration. The TinySA ULTRA contains all the components of a conventional heterodyne swept spectrum analyzer
• [Features] The RBW is as low as 200Hz, which can effectively distinguish adjacent signals and meet the requirements of SSB dual-satellite inter-modulation test. Input Step attenuator from 0dB to 31dB (can not be used not in combination with LNA). And, with the new ESD protection function, the product has a higher anti-static level and a longer service life
• [What You Get] 1x Tinysa ULTRA Spectrum Analyzer(4inch touchscreen, 3000mah rechargeable battery); 1x 25W Attenuator; 2x 30cm ALSR100 SMA cables; 1 x USB Type-C data cable; 1x SMA-SMA barrel connector; 1x TLanyard and touch plectrum; 1x Antenna with SMA connector; 1x 32GB MicroSD card(plugged in the host), 1x Stylus Pen
• [RF Attenuator Specification] RF Attenuator DC-3GHz 25W Coaxial Fixed Attenuator 10dB with N-male to N-female connector. VSWR: 1.20. Impedance:50 Ohm. Accuracy(dB): 1.0
• See more on Amazon...

Features

• Frequency: DC to 3GHz
• Connector: SMA male for Short and Load.
• Inpedance: 50 Ohm
• VSWR: less than 1.1
• Material: Copper, Shape: Circle.
• See more on Amazon...

Features

• Frequency Range: DC 6GHz
• Attenuation: 20dB
• VSWR: 1.2
• Impedance: 50 Ohm
• Package Include: 1 PCs 20dB SMA Male to SMA Female Attenuator
• See more on Amazon...

Features

• [Ultra Frequency Range] The measurement range of nanovna has been upgraded to 50kHz-4.4GHz. NanoVNA SV4401A is suitable for antenna testing of MF/HF/VHF/UHF bands. It can also be used to measure filters, amplifiers, attenuators, cables, power dividers, couplers, duplexers and other RF components. S11 and S21 parameters can be measured, where the S11 dynamic range is 50dB, and the S21 dynamic range is 75dB
• [Excellent Performance] The scan speed of SV4401A is 400 points/second, which enables a quasi-real-time measurement, and the maximum scanning points is up to 1001. The TDR function can be used to measure cable length. The RF interface of SV4401A is N-type female connector and a pair of N-to-SMA adapters are included, which can be used to connect DUTs with SMA interfaces
• [7 inch Large Touch Screen] The SV4401A nano vna is equipped with 7-inch IPS LCD and resistive touch screen with resolution of 800*480 pixels. There are 4 configuration items on the settings page: LANGUAGE, SLEEP TIME, TIME, BACKLIGHT. And there is a supporting bracket behind nanovna, which makes you more convenient at work. The antenna analyzer is equipped with 4 entity keys and you can quickly set the frequency, scale, on/off trace, add/delete marked points, screenshots, etc
• [PC Software Control] SV4401A is compatible with Windows/Linux/Macos. Connect the VNA to your PC with the USB Type-C cable, you can use the serial port to control the VNA such as setting the start and end frequency, obtain the measurement results, and setting the marking points. And the firmware can be upgraded via virtual U disk with USB Type-C cable
• [Data Storage - 8GB Memory Card] The antenna analyzer built-in 8GB memory card to store calibration status, SNP, files and screenshots, conveniently to analyze data. You do not need to worry about insufficient data storage space. This ensures data integrity and security
• [6700mAh Rechargeable Battery] The aursinc nanovna SV4401A battery have been improved to 6700mAh, built-in two 3350mAh lithium batteries which can continuously work about 10 hours, so you can work with it for a long time. Please use 5V/2A charger to charge the device
• [Package List] SV4401A (with built-in 8GB memory card and 2 battery 1; SMA OPEN calibration piece 1; SMA SHORT calibration piece 1; SMA LOAD calibration piece 1; N to SMA adapter 2; SMA-KK adapter 2; SMA-JJ adapter 1; 50cm SMA-JJ RG316 coaxial cable 2; USB Type-C cable 1; Storage bag 1
• See more on Amazon...

Features

• [ADVANCED NANOVNA] NanoVNA V2 Plus4 (S-A-A-2) is a 4GHz Transmission / Reflection vector network analyzer, measuring the S11 Reflection coefficient and the S21 Transmission coefficient of a high frequency network. With the latest version V2.4, update firmware: nanorfe .com/nanovna-versions.html
• [ULTRA-WIDE FREQUENCY RANGE] AURSINC NanoVNA V2 Plus4 provides a 50KHz-4GHz ultra-wide frequency range with an improved precision and accuration. And V2 Plus4 does not use harmonics for measurements. The system dynamic range for this nano vna is reaches to 90dB dynamic range (1GHz) and reaches to 80dB dynamic range (3GHz)
• [PERFORMANCE] With 4inch large touchscreen, you can flip the display(Menu - Display - Flip Display). All-aluminum alloy design, effective anti-interference. The scanning speed of NanoVNA V2 antenna analyzer increases by 4 times (400 points/sec). Low temperature drift, V2 Plus4 automatically internally corrects drift errors to achieve highly repeatable measurements
• [SUPPORT PC CONTROL] PC control via two PC applications (NanoVNA Saver / NanoVNA-QT), computer software compatible: Linux, Windows (7 or above), Mac OS. Support S parameter export and > 1024 points scan (NanoVNA-QT software). nanorfe .com/nanovna-v2-software.html
• [LARGER CAPACITY RECHARGEABLE BATTERY] The upgraded antenna analyzer is contained with a 3200mAh/3.7V lithium rechargeable battery with loger operating time and lasting battery life. There are battery charge LED indicators at the back of the VNA which are the battery fuel gauge, the one that is closest to the CH1 port connector is the lowest charge level indicating 25%
• [WHAT ARE INCLUDED] AURSINC NanoVNA V2 Plus4 is the Original edition (if you buy the clone one the VNA cannot proceed the software update forM the official site) NanoVNA V2 PLUS4 V2.4 comes with a 4-piece calibration set - open, short, load, & thru, two male-male SMA cables, a USB2-B to USB2-A cable (black or silver), and a stylus to operate the touch screen menu and markers
• See more on Amazon...

Features

• [Upgraded Performance] nanovna f v3 with 4.3inch (800x480pixel) touchscreen display, 1MHz to 6GHz widely measuring range. With the optimally designed signal processing system, the scan speed is up to 200 points/s and the maximum scanning points is up to 801. The RF interface of antenna analyzer is SMA connector witch can be used to connect DUTs directly and the nanovna analyzer supports TDR function for cable lengths measurement
• [Ultra Wide Frequency] Compared with the nanovna f v2 (50kHz-3GHz), the nanovna f v3 antenna analyzer measurement range is improved to 1MHz-6GHz. It can be used for S11 and S21 measurements. The S21 dynamic range of NanoVNA-F V3 is 65 dB, while the S11 dynamic range is 50 dB. The scan points is up to 101-801 and the calibration result storage is 12, covering up to the full low or high frequency range. The vna antenna analyzers are versatile and offer faster and more efficient operation
• [Efficient and Worthwhile] The nano vna antenna analyzer is made of metal material, which is durable and can effectively shield electromagnetic interference. Powerful features, including automatic calibration, PC software control, compatible with NanoVNA-Saver to facilitate measurement data transfer, storage and export. Built-in 4500m-ah rechargeable battery, with C-type charging cable and LED charging indicator, suitable for indoor or outdoor application
• [Multiple Measurement Functions] NanoVNA-F V3 antenna analyzer is suitable for antenna testing of MF/HF/VHF/UHF/SHF bands. It can also be used to measure filters, amplifiers, attenuators, cables, power dividers, couplers, duplexers and other RF components. Supports a variety of display formats: Log Mag, Linear Mag, Phase, Smith R+jX, Smith R+L/C, VSWR, Polar, Group delay, Resistance, Reactance, etc. Nano vna antenna analyzer are widely used, with fast response time and high operating efficiency
• [Authentic & Package] NanoVNA-F V3 developed by Hugen. Package include AURSINC NanoVNA-F V3 host (with 4500mAh battery) display: 4.3 inch TFT x1, SMA OPEN/SHORT/LOAD calibration kit 1, SMA-KK adapter 1, SMA-JJ adapter 1, SMA-JKW adapter 1, 20cm SMA-JJ RG405 coaxial cable 2, USB type-C cable 1. The vna antenna analyzer provide reliable and accurate measurement results for ham radio operators and professionals.
• See more on Amazon...

Features

• [Frequency Range] Transmission Mearsure S21: 70dB(50KHz-1.5GHz), 60dB(1.5GHz-3GHz). Reflection Measure S11: -50dB(50KHz-1.5GHz), -40dB(1.5GHz-3GHz); Antenna Analyzer: 1.005(50KHz - 1.5GHz), 1.02(1.5GHz-3GHz)
• [Note Recalibrate] The SAA-2N/NanoVNA_V2.2 uses a similar user interface to the NanoVNA, but with a different technical architecture, the SAA-2N/NanoVNA_V2.2 does not load the initial calibration data at startup, and does not automatically interpolate the calibration data after the user changes the frequency, and must recalibrate or call back the calibration data after each startup and frequency change. Please read the user manual carefully before use to avoid damaging the device
• [PC Connection] nanovna saa-2n can be controlled by PC via VNA-QT software,supported for Linux, Windows (7+), Mac OS planned. It also support Nanovna-Saver for extracting the data for display on a computer, and for saving to Touchstore files
• [Compliance] SAA-2N 3GHz vector network analyzer, designed in collaboration with OwOComm. Under the LGPL license agreement, it is completely manufactured according to the v2_2 files issued by OwOComm at Development Department, in line with the original technical specifications
• See more on Amazon...

Features

• If the board fails to work on duplex mode, please run the upgrade command: sudo pistar-mmdvmhshatflash hs_dual_hat (if this command doesn't work, please try this command: mmdvm.club/index.php/wpsd .html)
• WIDELY COMPATIBLE: Supports DMR, P-25, D-Star and System Fusion. HIGH PERFORMACE: 32-bit ARM processor, up to 10mW RF power, fully tested every piece
• WORK with RASBERRY Pi: Mounts cleanly on current Raspberry Pi including the Pi Zero, NOT compatible with Rasberry Pi 4
• EASY OPERATION: The firmware is pre-loaded and is easily upgraded via software. Onboard LEDs showing status (Tx, Rx, PTT, Mode)
• FREQUENCY: UHF 433-900MHz, VHF144-146. NOTE: TX =0, RX=0. Modem select: STM32_HS_GPIO ; To leave the screen on all the time In Pi-Star configuration, ensure you have OLED Type 3 in the display type field at the top of the page, set Port to: modem. Also, in the Expert section, go to MMDVM host, and scroll down to the OLED section. Make sure LogoScreensaver is set to 1. This leaves the screen on all the time. Otherwise, it goes blank when idle
• Update new FW 1.5.2 : (pi-star / expert / ssh access / user :pi-star pass:raspberry) then run sudo pistar-mmdvmhshatflash hs_dual_hat set Jumper BOOT0=1,BOOT1=0 and soler JP1 First! After upgraded finished, disconnect JP1
• See more on Amazon...

Features

• [Upgrade NANOVNA] ORIGINAL NanoRFE VNA6000 is a 6GHz Transmission/Reflection vector network analyzer, measuring the S11 Reflection coefficient and the S21 Transmission coefficient of a high frequency network; Not only testing standing wave impedance of the antenna, but also can debug the duplexer, the insertion loss of the filter, the isolation and testing the attenuation of the cable, shorten the coefficient, the phase, the amplification of the antenna amplifier
• [ULTRA-WIDE FREQUENCY RANGE] Compared to the previous NanoVNAs (10KHz-1.5/3GHz), AURSINC NanoVNA NanoRFE VNA6000 provides a 50KHz-6GHz ultra-wide frequency range with an improved precision and accuration, Moreover, the System dynamic range for this VNA is up to 95dB dynamic range
• [LARGER CAPACITY RECHARGEABLE BATTERY] The upgraded vector network analyzer is contained with a 3200mAh/3.7V lithium rechargeable battery with loger operating time and lasting battery life. Also there are battery charge LED indicators at the back of the VNA which are the battery fuel gauge, the one that is closest to the CH1 port connector is the lowest charge level indicating 25%
• [PC CONTROL] The antenna analyzer is equipped with S parameters export, Automatic continuous data acquisition, Custom calibration kit parameters along with support PC software control, like Windows (above 7), Linux, MacOS, the VNA can be more compatible with PC and antenna measurements, when measuring the frequency
• [Extensible Feature] The Adjustable IFBW of the VNA600 enables optimal tradeoff between measurement speed and noise and can measure narrowband devices; Flip Display, for your using convenience, you can flip the display as the following steps: Menu - Display - Flip Display
• See more on Amazon...

Features

• UPGRADED NANOVNA-H4 V4.3 AURSINC nanovna h4 is a Hugen Origin that provides perfect vector network measurement capabilities, tiny and handheld, stand-alone with 4inch LCD display, with 1950mAh battery powered or USB powered. With latest HW 4.3 version, Nanovna-h4 antenna analyzer is added a brand new panel plus added a new SD port for data storage(support up to 32GB memory card, not included in the package)
• IMPROVED FREQUENCY ALGORITHM The improved frequency algorithm of nano vna h4 can use the odd harmonic extension of si5351 to support the measurement frequency up to 1.5GHz. The 50K-300MHz frequency range of the si5351 direct output provides better than 70dB dynamic. The extended 300M-900MHz band provides better than 60dB of dynamics, and the 900M-1.5GHz band is better than 40dB of dynamics. Used it to check out new cable or antenna installations and to routinely adjust the RF tuner for optimum
• ANTENNA PERFORMANCE MEASUREMENT The default firmware main function for vector network analyzer is used for antenna performance measurement. It has good RF performance for S-parameter measurements as previous models. NOTE: the Nanovna is only compatible with the low-speed and supports SPI mode SD cards for now. It is very efficient vector testing for ham radio operator, research electrical engineer and antenna builders
• TinySA Ultra Tinysa Ultra developed by Hugen, HW V0.4.5.1. With 4inch touch screen(480*320 pixels resolution), tinysa ultra spectrum analyzer has ultra measurement range from 100kHz to 5.3GHz, built-in 32Gb micro SD card for data transfer and storage. Linear power supply to avoid switching noise
• TinySA Ultra 2 in 1 Device When not used as Spectrum Analyzer it can be used as Signal Generator, MF/HF/VHF sinus output between 100kHZ-800MHz, UHF square wave output between 800mHz-4.4GHz, Mixing signal output is between 4.4GHz-5.4GHz. Built-in calibration signal generator that is used for automatic self test and low inputcalibration. The TinySA ULTRA contains all the components of a conventional heterodyne swept spectrum analyzer
• See more on Amazon...

Features

• [Upgraded TinySA Ultra] Tinysa Ultra developed by Hugen, HW V0.4.5.1. With 4inch touch screen(480*320 pixels resolution), tinysa ultra spectrum analyzer has ultra measurement range from 100kHz to 5.3GHz, built-in 32Gb micro SD card for data transfer and storage. Linear power supply to avoid switching noise
• [Frequency Range] Tiny sa ultra measures from 100KHz-5.3GHz: Spectrum Analyzer for 0.1MHz-800MHz, with Ultra mode enabled, level calibrated up to 6GHz, can observe signals up to 12GHz. Switchable resolution bandpass filters from 200Hz-850kHz. You can fast and accurate execute measurement tests
• [Features] The RBW is as low as 200Hz, which can effectively distinguish adjacent signals and meet the requirements of SSB dual-satellite inter-modulation test. Input Step attenuator from 0dB to 31dB (can not be used not in combination with LNA). And, with the new ESD protection function, the product has a higher anti-static level and a longer service life
• [RF Attenuator Specification] RF Attenuator DC-3GHz 25W Coaxial Fixed Attenuator 10dB with N-male to N-female connector. VSWR: 1.20. Impedance:50 Ohm. Accuracy(dB): 1.0
• [SMA Calibration Kit] Frequency: DC to 3GHz Connector: SMA male for Short and Load. Inpedance: 50 Ohm VSWR: less than 1.1 Material: Copper, Shape: Circle
• See more on Amazon...

Features

• [Upgraded TinySA Ultra] Tinysa Ultra developed by Hugen, HW V0.4.5.1. With 4inch touch screen(480*320 pixels resolution), tinysa ultra spectrum analyzer has ultra measurement range from 100kHz to 5.3GHz, built-in 32Gb micro SD card for data transfer and storage. Linear power supply to avoid switching noise
• [Frequency Range] Tiny sa ultra measures from 100KHz-5.3GHz: Spectrum Analyzer for 0.1MHz-800MHz, with Ultra mode enabled, level calibrated up to 6GHz, can observe signals up to 12GHz. Switchable resolution bandpass filters from 200Hz-850kHz. You can fast and accurate execute measurement tests
• [2 in 1 Device] When not used as Spectrum Analyzer it can be used as Signal Generator, MF/HF/VHF sinus output between 100kHZ-800MHz, UHF square wave output between 800mHz-4.4GHz, Mixing signal output is between 4.4GHz-5.4GHz. Built-in calibration signal generator that is used for automatic self test and low inputcalibration. The TinySA ULTRA contains all the components of a conventional heterodyne swept spectrum analyzer
• [Features] The RBW is as low as 200Hz, which can effectively distinguish adjacent signals and meet the requirements of SSB dual-satellite inter-modulation test. Input Step attenuator from 0dB to 31dB (can not be used not in combination with LNA). And, with the new ESD protection function, the product has a higher anti-static level and a longer service life
• N DC Block can access transmission line,isolate the influence of DC power to signal source and measure instrument, and has wide band and low insertion loss characteristics.
• See more on Amazon...

Features

• [Upgraded TinySA Ultra] Tinysa Ultra developed by Hugen, HW V0.4.5.1. With 4inch touch screen(480*320 pixels resolution), tinysa ultra spectrum analyzer has ultra measurement range from 100kHz to 5.3GHz, built-in 32Gb micro SD card for data transfer and storage. Linear power supply to avoid switching noise
• [Frequency Range] Tiny sa ultra measures from 100KHz-5.3GHz: Spectrum Analyzer for 0.1MHz-800MHz, with Ultra mode enabled, level calibrated up to 6GHz, can observe signals up to 12GHz. Switchable resolution bandpass filters from 200Hz-850kHz. You can fast and accurate execute measurement tests
• [RF Attenuator Specification] RF Attenuator DC-3GHz 25W Coaxial Fixed Attenuator 10dB with N-male to N-female connector. VSWR: 1.20. Impedance:50 Ohm. Accuracy(dB): 1.0
• This test board contains a plug-in test circuit suitable for VNA Testboard, and a set of 0805 and 1206 patch test circuits are added. The Testboard kit allows NanoVNA users to assemble a useful Component jig to quickly assemble a simple RF circuit and evaluate their performance on the NanoVNA
• Product come unassembled, you need to assemble according to your purpose. Please prepare your own welding tools and build a test circuit according to your test needs. We are not responsible for circuit guidance
• See more on Amazon...

Features

• [NanoVNA H4]AURSINC nanovna-h4 is a Hugen Origin that provides perfect vector network measurement capabilities, tiny and handheld, stand-alone with 4inch LCD display, with 1950mAh battery powered or USB powered. With latest HW 4.3 version, Nanovna-h4 antenna analyzer is added a brand new panel plus added a new SD port for data storage(support up to 32GB memory card, not included in the package)
• [NanoVNA H4]The improved frequency algorithm of nanovna h4 can use the odd harmonic extension of si5351 to support the measurement frequency up to 1.5GHz. The 50K-300MHz frequency range of the si5351 direct output provides better than 70dB dynamic. The extended 300M-900MHz band provides better than 60dB of dynamics, and the 900M-1.5GHz band is better than 40dB of dynamics. Used it to check out new cable or antenna installations and to routinely adjust the RF tuner for optimum
• [NanoVNA H4]The default firmware main function for vector network analyzer is used for antenna performance measurement. It has good RF performance for S-parameter measurements as previous models. NOTE: the Nanovna is only compatible with the low-speed and supports SPI mode SD cards for now. It is very efficient vector testing for ham radio operator, research electrical engineer and antenna builders
• [2.8Tinysa]Tinysa produced by Hugen, with V0.3.1 hardware. The firmware of the tinySA can be updated, for newest firmware version update, please refer to: tinysa .org. The displayed version info indicates ESD protection with a diode for improved stability, sensitivity, anti-static level and longevity
• [2.8Tinysa]The tinysa spectrum analyzers use a resolution filter to isolate input power within a narrow frequency range. This resolution filter is swept across the desired frequency range. The fastest scanning speed occurs with an RBW or 300kHz or wider and is about 2 scans per second. The scanning speed decreases rapidly as the frequency span increases and the RBW decreases. A scan from 0MHz to 350MHz with an RBW of 10kHz takes about 2 minutes
• See more on Amazon...

Features

• [NanoVNA-H] New HW Version V3.6. It is upgradeable as new firmware is developed. With MicroSD card port now can have the measurement data or the screenshots saved in the it at anytime. Added battery circuit management, more secure. Redesigned PCB, you can connect to mobile phone with Type C-Type C cable (original PCB needs OTG cable), see a clear HD image on your phone. Added a ABS case, which is protective and dust-proof. Disply: 2.8 inch TFT (320 x240)
• [NanoVNA-H]The improved frequency algorithm can use the odd harmonic extension of si5351 to support the measurement frequency up to 1.5GHz. The 50K-300MHz frequency range of the si5351 direct output provides better than 70dB dynamic, The extended 300M-900MHz band provides better than 60dB of dynamics, and the 900M-1.5GHz band is better than 40dB of dynamics
• [NanoVNA-H] The default firmware main function is used for antenna performance measurement. The TX/RX method can measure the complete S11 and S21 parameters. If you need to obtain S12 and S22, you need to manually replace the transceiver port wiring. The CH0 output level is increased to 0dBm when using the fundamental wave, resulting in more accurate reflection measurement
• [TinySA 4inch] AURSINC tinysa ultra developed by Hugen, hardware version V0.4.5.1. Now have new hardware system V0.4.5.1.1 - Updated LCD screen for availability reasons. With the new ESD protection function, the product has a higher anti-static level and a longer service life. Linear power supply to avoid switching noise
• [TinySA 4inch]Tiny SA Ultra has an ultra wide measuring frequency range of 100kHz to 5.3GHz, spectrum analyzer for 100kHz-800MHz and Ultra mode up to 6GHz, can observe signals up to 12GHz. Switchable resolution bandpass filters from 200Hz to 850kHz, you could fast and accurate execute measurement tests
• See more on Amazon...

Features

• [NanoVNA-H]New HW Version V3.6. It is upgradeable as new firmware is developed. With MicroSD card port now can have the measurement data or the screenshots saved in the it at anytime. Added battery circuit management, more secure. Redesigned PCB, you can connect to mobile phone with Type C-Type C cable (original PCB needs OTG cable), see a clear HD image on your phone. Added a ABS case, which is protective and dust-proof. Disply: 2.8 inch TFT (320 x240)
• [NanoVNA-H]The improved frequency algorithm can use the odd harmonic extension of si5351 to support the measurement frequency up to 1.5GHz. The 50K-300MHz frequency range of the si5351 direct output provides better than 70dB dynamic, The extended 300M-900MHz band provides better than 60dB of dynamics, and the 900M-1.5GHz band is better than 40dB of dynamics
• [NanoVNA-H]The default firmware main function is used for antenna performance measurement. The TX/RX method can measure the complete S11 and S21 parameters. If you need to obtain S12 and S22, you need to manually replace the transceiver port wiring. The CH0 output level is increased to 0dBm when using the fundamental wave, resulting in more accurate reflection measurement
• [ Nanovna SMA Attenuator Kit]Frequency Range: DC 6GHz
• [ Nanovna SMA Attenuator Kit]VSWR: 1.2
• See more on Amazon...

Features

• [TinySA Ultra Spectrum Analyzer 4inch]AURSINC tinysa ultra developed by Hugen, hardware version V0.4.5.1. Now have new hardware system V0.4.5.1.1 - Updated LCD screen for availability reasons. With the new ESD protection function, the product has a higher anti-static level and a longer service life. Linear power supply to avoid switching noise
• [TinySA Ultra Spectrum Analyzer 4inch] Tiny SA Ultra has an ultra wide measuring frequency range of 100kHz to 5.3GHz, spectrum analyzer for 100kHz-800MHz and Ultra mode up to 6GHz, can observe signals up to 12GHz. Switchable resolution bandpass filters from 200Hz to 850kHz, you could fast and accurate execute measurement tests
• [TinySA Ultra Spectrum Analyzer 4inch]With 4 inch touch screen (480*320 pixels resolution), providing clear data images and sensitive operation touch. Color display showing max 450 points providing gapless covering up to the full frequency range. This displays frequencies all the up to the ranges of 5.2 GHz WiFi and is a great way to visually identify where to put your access points, or if your faraday shielding is effective.
• [Tester Board] The RF Demo Kit is a NanoVNA RF test board independently designed by BH5HNU, with a size of 10*10cm / 3.94*3.94 inch. The demo calibration board for evaluating and learning nanaovna vector network analyzer, antenna analyzer test calibration learning, making sure your setup is working
• [Tester Board]this RF Demo Kit has 18 functional modules- the board is totally integrated with 18 functional modules. Can be used to measure 30MHz short wave low-pass-filter LPF, 100MHz FM high-pass filter HPF, 433MHz commonly used SAW band pass filter BPF, 6.5MHz ceramic trap BSFtt
• See more on Amazon...

Features

• [UPGRADED TINYSA ULTRA] Developed by Hugen, hardware version V0.4.5.1. Now have new hardware system V0.4.5.1.1 - Updated LCD screen for availability reasons. With 4in touch screen with 480*320 pixels resolution, Tinysa ULTRA spectrum analyzer owns a larger measurement range from 100kHz to 5.3GHz, new ESD protection function, built-in 32Gb micro SD card for data transfer and storage, Linear power supply to avoid switching noise
• [TINYSA ULTRA] TinySA ULTRA measures from 100KHz - 5.3GHz: Spectrum Analyzer for 0.1-800MHz, with Ultra mode enabled, level calibrated up to 6GHz, can observe signals up to 12GHz. Switchable resolution bandpass filters from 200Hz to 850kHz. Color display showing max 450 points providing gapless covering up to the full frequency range. You can fast and accurate execute measurement tests
• [TINYSA ULTRA] This spectrum analyzer can connect to a PC via USB, realize the USB serial (CDC) protocol, and can be invoke a large number of commands through the serial interface. These commands can be used to perform measurements or update internal Settings. Built-in Linux drivers, Windows drivers are automatically installed when connected to a Windows PC. Tinysa-APP directly transfers data to the computer
• [NANOVNA-F V2] The NanoVNA-F V2 upgraded to the latest Firmware V0.4.0, the operation page is compatible with Nanovna-F. More features that it enables measurements of S-parameter, voltage standing wave ratio (SWR), phase map, group delay, Smith chart, DELAY, POLAR, LINEAR and more
• [NANOVNA-F V2] The measurement range of nanovna-f v2 expanded to 50KHz-3GHz. The TX/RX method can measure the complete S11 and S21 parameters, S21 dynamic ranges: 70dB (1.5GHz), 60dB (3GHz); S11 dynamic ranges: 50dB (1.5GHz), 40dB (3GHz). Rugged and durable aluminum alloy cases, shielding electromagnetic interference to ensure precise measurements.
• See more on Amazon...

Features

• [Upgraded NanoVNA V2 Plus5] Compared to NanoVNA V2 PLUS4, the V2 PLUS4 Pro has the same appearance as the plus4, with a few more options in the menu. Update: 1. Hardware added bandwidth adjustment function; 2. It can measure narrowband devices, such as crystal oscillators; 3. The maximum scan speed is faster than before, the default parameter is 0.16 seconds per scan, instead of 0.25 seconds
• [ADVANCED FREQUENCY RANGE] NanoVNA V2 Plus5 is a 4GHz T/R vector network analyzer developed by HCXQS in collaboration with OwOComm. Compared to earlier NanoVNA versions, V2 does not use harmonics for measurements and reaches to 90dB dynamic range. NanoVNA V2 Plus5 provides a 50KHz-4GHz frequency range, has improved shielding that achieves high dynamic range with an aluminum enclosure
• [SUPPORT PC CONTROL] PC control via two PC applications (NanoVNA Saver / NanoVNA-QT), computer software compatible: Linux, Windows (7 or above), Mac OS. It works well with a computer to print out Standing Wave Ratios, Smith Charts and other Antenna related information over various frequency ranges
• [LARGER CAPACITY RECHARGEABLE BATTERY] The upgraded vector network analyzer is contained with a 3200mAh/3.7V lithium rechargeable battery with loger operating time and lasting battery life. Also there are battery charge LED indicators at the back of the VNA which are the battery fuel gauge, the one that is closest to the CH1 port connector is the lowest charge level indicating 25%
• [WHAT ARE INCLUDED] 1x NanoVNA V2 Plus5 (V2 PLUS4 Pro), 4 x Calibration set - open, short, load, & thru, 2x Male to Male SMA cables, 1x USB2-B to USB2-A cable (black or silver), 1x stylus to operate the touch screen menu and markers
• See more on Amazon...

Features

• [NanoVNA-F V2] The NanoVNA-F V2 upgraded to the latest Firmware 0.4.0, the operation page is compatible with Nanovna-F. It enables measurements of S-parameter, voltage standing wave ratio (SWR), phase map, group delay, Smith chart, DELAY, POLAR, LINEAR and more
• [NanoVNA-F V2] Frequency Range - The measurement range of nanovna-f v2 expanded to 50KHz-3GHz. The TX/RX method can measure the complete S11 and S21 parameters, S21 dynamic ranges: 70dB (1.5GHz), 60dB (3GHz); S11 dynamic ranges: 50dB (1.5GHz), 40dB (3GHz)
• [NanoVNA-F V2] 4.3'' Screen & 5000mAh Battery - The nanovna has a 4.3-inch IPS TFT LCD screen with a resolution of 800*480 and a resistive touch screen, providing a large viewing angle. It is equipped with an 5000mAh lithium battery for longer standby time, up to 7 hours of usage. With the use of a 2A large-current charging IC, the charging time is reduced. As an add-on, it built-in 5V output for charging Android phones or tablets
• [RF Demo Kit] This a NanoVNA RF test board independently designed by BH5HNU, with a size of 10 * 10CM. The VNA test board demo calibration board for learning nanaovna Vector Network Analyzer, Antenna Analyzer test calibration learning.
• [RF Demo Kit] has 18 functional modules- the board is totally integrated with 18 functional modules. Can be used to measure 30MHz short wave low-pass-filter LPF, 100MHz FM high-pass filter HPF, 433MHz commonly used SAW band pass filter BPF, 6.5MHz ceramic trap BSFtt
• See more on Amazon...

Features

• [2022 Upgraded Nanovna-H4 HW V4.3] Latest features: with latest HW 4.3 version, Nanovna-H4 is added a brand new panel plus added a new SD port for data storage(support up to 32GB memory card, not included in the package). The NanoVNA-H4 vector network analyzer is a Hugen Origin that provides perfect vector network measurement capabilities, tiny and handheld, stand-alone with 4-inch LCD display, portable with 1950mAh battery powered or USB powered
• [Improved Frequency Algorithm] The improved frequency algorithm of NanoVNA-H4 can use the odd harmonic extension of si5351 to support the measurement frequency up to 1.5GHz. The 50K-300MHz frequency range of the si5351 direct output provides better than 70dB dynamic, The extended 300M-900MHz band provides better than 60dB of dynamics, and the 900M-1.5GHz band is better than 40dB of dynamics;The metal shield is designed to reduce the external interference and improve the measurement accuracy
• [Antenna Performance Measurement] The default firmware main function for NanoVNA-H4 vector network analyzer is used for antenna performance measurement. The TX/RX method can measure the complete S11 and S21 parameters. If you need to obtain S12 and S22, you need to manually replace the transceiver port wiring
• [PC Control] Using PC software NanoVNASaver, NanoVNA-H4 antenna analyzer can connect to a NanoVNA and extracts the data for display on a computer, and for saving to Touchstone files. We can export Touchstone (snp) files for various radio design and simulation software through PC software
• [What are Included?] NanoVNA-H4 host (with battery) x1, USB Type-C data cable x1, Card Reader with 32GB Micro SD Card 30mm SMA male to male RG174 RF cable x2, SMA simple calibration kit x1, SMA female to female connector x1. NOTE: the Nanovna is only compatible with the low-speed and supports SPI mode SD cards for now.
• See more on Amazon...

Features

• Frequency Range: DC 6GHz
• Attenuation: 3db/6db/10db/20db
• VSWR: 1.2
• Impedance: 50 Ohm
• Include: 1 PCs 3db/6db/10db/20db SMA Male to SMA Female Attenuator
• See more on Amazon...