BETAFPV ExpressLRS OpenTX Mini Nano Receiver High Refresh Rate Long Range Performance for FPV Racing Drone
Asin: B09B28HSVB | Model: 01070001_1 | PartNumber: 01070001_1
As an Amazon Associate we earn a fee from qualifying purchases when you follow a link to Amazon from this page. We rank the products, but the links to Amazon are promotional.【Crossfire Serial Protocol 】Expresslrs Uses The Crossfire Serial Protocol (Aka Crsf Protocol) To Communicate Between The Receiver And The Flight Controller Board. So Make Sure Your Flight Controller Board Supports The Crsf Serial Protocol. How To Set Up The Crsf Protocol Can Be Viewed On The Fourth Page Of The Manual..
【Configuration & Bind】 Nano Receiver Could Enter Binding Status By Power On/Off Three Times. Step: Plugin And Unplug Nano Receiver Three Times; Make Sure The Led Is Doing A Quick Double Blink, Which Indicates The Receiver Is In Bind Mode; Make Sure The Rf Tx Module Or Radio Transmitter Enter Binding Status, Which Sends Out A Binding Pulse; If The Receiver Has A Solid Light, It's Bound..
【Nano Size】This Receiver Only Has 0.7 Grams And The Volume Is 12Mm*19Mm Which Is Very Suitable For Tiny Whoop Because Of The Ultra Light And Nano Size..
【Expresslrs Receiver】Betafpv Nano Receiver Is Based On The Expresslrs Project, An Open-Source Rc Link For Rc Applications Which Aims To Achieve The Best Possible Link Performance In Both Speeds, Latency, And Range Suit For Elrs Tx Module Or Nano Bay, Etc..
Features
- ExpressLRS ExpressLRS is an open-source RC link for RC applications, based on Semtech Lora SX127x or SX1280 hardware for RX and TX respectively. This makes ExpressLRS one of the fastest RC links available while still offering long-range performance.
- ExpressLRS Receiver BETAFPV Nano receiver is based on the ExpressLRS project, an open-source RC link for RC applications which aims to achieve the best possible link performance in both speeds, latency, and range suit for ELRS TX module or Nano bay, etc.
- Crossfire Serial Protocol ExpressLRS uses the Crossfire serial protocol (AKA CRSF protocol) to communicate between the receiver and the flight controller board. So make sure your flight controller board supports the CRSF serial protocol. How to set up the CRSF protocol can be viewed on the fourth page of the manual.
- Nano Size This receiver only has 0.7 grams and the volume is 12mm*19mm which is very suitable for Tiny whoop because of the ultra light and Nano size.
- Configuration & Bind Nano receiver could enter binding status by power on/off three times. Step: Plugin and unplug nano receiver three times; Make sure the LED is doing a quick double blink, which indicates the receiver is in bind mode; Make sure the RF TX module or radio transmitter enter binding status, which sends out a binding pulse; If the receiver has a solid light, it's bound.
- See more on Amazon...
Brand: BETAFPV | Manufacturer: BETAFPV
Dimensions: 0.39 x 3.94 x 2.76 inches
See On Amazon Similar To BETAFPV ExpressLRS OpenTX Mini Nano
#1
BETAFPV Betaflight Cetus X FPV Drone Kit with LiteRadio 3 Transmitter VR03 FPV Goggles with DVR Recording Function, Supported 2S Power Advanced RTF Kit for FPV Beginners to Fly Faster Further-ELRS V3
Asin: B0BJVP3XW7 | Model: 01020005_1 | PartNumber: 01020005_1
【Literadio 3 Transmitter】Betafpv Literadio 3 Transmitter Features An Ergonomically Designed Handle And Has Superb Performance In Its Working Time Lasting Up To 15 Hours. It Also Supports Betafpv Configurator, Which Is A Utility Designed To Simply Update, Configure, And Tune The Radio Controller. But Please Note That It's Firmware Is V3 And Do Not Support External Tx Module Now..
【About Bind】The Cetus X Fpv Kit's Firmware Is Elrs V3, It Can't Be Bound With Your Equipment With Elrs 2.X Version. Please Make Sure The Other Receiver Bind With The Controller Has Same Firmware Version And Then Could Be Bound Together..
【Vr03 Goggles】Betafpv Vr03 Goggles Come With A Dvr Recording Function. Pilots Can Enjoy The Playback Saved Through The Goggles Or Export The Videos By Micro Sd Card (Not Included), Supporting Most Analog Vtxs In The Market. This Exciting Function Allows Pilots To Catch The Memorably Breathtaking Moment, Greatly Heightening The Fpv Flying Experience..
【Calibration】Please Re-Calibrate The Joystick After Repeated Use Or The Remote Control Radio Transmitter Is Subjected To Physical Impact, Or The Drone Occurs A Phenome Of The The Drone Fly To One Side. If The Drone Has Something Wrong With The Prop And Motor, Please Follow The Manual To Re-Calibrate The Flight Controller. Please Contact Us Directly If You Don't Know How To Do That..
【Betaflight Supported】Flying A Drone Expertly Is The First Step To Being A Drone Master And The Next Is To Set Up. With The Support Of The Betaflight Configurator, Beginners Can Learn Quadcopter Configuration Through The Betaflight Fc Version..
Features
- Cetus X FPV Kit BETAFPV Cetus X FPV Kit, as the advanced ExpressLRS 2S power whoop bundle, is a completely primary choice to reach a higher stage. Comes with an enhanced propulsion system, VR03 goggles, LiteRadio 3 radio transmitter controller, longer radio and video transmission, pilots can unlock more accomplishments to the next level.
- Betaflight Supported Flying a drone expertly is the first step to being a drone master and the next is to set up. With the support of the Betaflight configurator, beginners can learn quadcopter configuration through the Betaflight FC version.
- LiteRadio 3 Transmitter BETAFPV LiteRadio 3 Transmitter features an ergonomically designed handle and has superb performance in its working time lasting up to 15 hours. It also supports BETAFPV Configurator, which is a utility designed to simply update, configure, and tune the radio controller. But please note that it's firmware is V3 and do not support external TX module now.
- Calibration Please re-calibrate the joystick after repeated use or the remote control radio transmitter is subjected to physical impact, or the drone occurs a phenome of the the drone fly to one side. If the drone has something wrong with the prop and motor, please follow the manual to re-calibrate the flight controller. Please contact us directly if you don't know how to do that.
- About Bind The Cetus X FPV Kit's firmware is ELRS V3, it can't be bound with your equipment with ELRS 2.X version. Please make sure the other receiver bind with the controller has same firmware version and then could be bound together.
- VR03 Goggles BETAFPV VR03 Goggles come with a DVR recording function. Pilots can enjoy the playback saved through the goggles or export the videos by Micro SD card (not included), supporting most Analog VTXs in the market. This exciting function allows pilots to catch the memorably breathtaking moment, greatly heightening the FPV flying experience.
- See more on Amazon...
Brand: BETAFPV | Manufacturer: BETAFPV
Dimensions: 5.39 x 10.35 x 8.50 Inches | Weight: 0.12 pounds
See On Amazon #2
BETAFPV Aquila16 FPV Drone Kit with Altitude Hold, 8Mins Flight, for FPV Beginner to Fly Indoor Outdoor Longer, 3 Flight&Speed Modes, DVR Recording, Simulator Supported, 1S RTF Kit with ELRS 3.0
Asin: B0CQY4QZBF
🛩️【Flight Modes】The Aquila16 Brushless Quadcopter Offers N/S/M 3 Flight Modes And Supports 3 Different Speeds With Slow/Mid/Fast. With Turtle Mode, No Burden To Fly Away, And There Is No Need To Walk Away To Correct The Position Manually To Flip It Over And Resume Flying When The Quadcopter Falls To The Ground And Upside Down. Whether You're A Seasoned Fpv Pilot Or A Complete Beginner, The Aquila16 Fpv Kit Empowers Everyone To Fly Confidently From Day One..
🛩️【Package&Warranty】All Components, Including The Quadcopter, Radio Transmitter, Fpv Goggles, And Accessories, Are Conveniently Packed In A Portable Eva Storage Bag For Easy Transportation And Enhanced Equipment Protection. Please Verify That All Components Are Included, Without Damage And With No Deformation, All Parts Are Fully Charged Before Flying The Kit. If Not Or No Matter What Is Wrong With Your Betafpv Items, Betafpv Guarantees To Serve You!.
🛩️【Inverted Designed】The Inclusion Of An Inverted Duct System Enhances Thrust And Stability, Enabling The Drone To Achieve Superior Flight Performance With Precision. The Fixed Configuration Port And Modular Battery Minimize Redundancy Designs, Making Installation Simple And Hassle-Free. The Duct Guard Design Ensures Safe Flights By Protecting The Propellers, Equipped To Handle Unexpected Obstacles..
🛩️【Altitude Hold】The Aquila16 Drone Excels In Hover Capability For Assisted Flight, Ensuring Safe And Effortless Flight For Worry-Free Learning. Built-In Highly Precise Barometer To Detect The Height, It Benefits From Great Stability Due To Its Position Hold Mode, And Auto-Hovering, Which Enables The Drone To Stay At The Current Height. This Function Guarantees Emergency Landing In Situations Of Lost Control Or Low Battery..
Features
- 8Mins Flight Aquila16 FPV Kit with an impressive 8-minute flight time, pilots can enjoy endless practice sessions and a flight distance of up to 200m indoors or outdoors. Enjoy uninterrupted flights, enabling pilots to concentrate on refining their piloting skills. The kit features a high-power, low-latency 350 video transmission system, guaranteeing real-time video transmission with stable signals up to 200 meters. Say goodbye to lag and immerse yourself in the thrill of the flight.
- Altitude Hold The Aquila16 drone excels in hover capability for assisted flight, ensuring safe and effortless flight for worry-free learning. Built-in highly precise barometer to detect the height, it benefits from great stability due to its position hold mode, and auto-hovering, which enables the drone to stay at the current height. This function guarantees emergency landing in situations of lost control or low battery.
- Flight Modes The Aquila16 Brushless Quadcopter offers N/S/M 3 flight modes and supports 3 different speeds with SLOW/MID/FAST. With Turtle Mode, no burden to fly away, and there is no need to walk away to correct the position manually to flip it over and resume flying when the quadcopter falls to the ground and upside down. Whether you're a seasoned FPV pilot or a complete beginner, the Aquila16 FPV Kit empowers everyone to fly confidently from day one.
- Inverted Designed The inclusion of an inverted duct system enhances thrust and stability, enabling the drone to achieve superior flight performance with precision. The fixed configuration port and modular battery minimize redundancy designs, making installation simple and hassle-free. The duct guard design ensures safe flights by protecting the propellers, equipped to handle unexpected obstacles.
- Package&Warranty All components, including the quadcopter, radio transmitter, FPV goggles, and accessories, are conveniently packed in a portable EVA storage bag for easy transportation and enhanced equipment protection. Please verify that all components are included, without damage and with no deformation, all parts are fully charged before flying the kit. If not or No matter what is wrong with your BETAFPV items, BETAFPV guarantees to serve you!
- See more on Amazon...
Brand: BETAFPV | Manufacturer: BETAFPV
Dimensions: 5.51 x 10.43 x 8.66 inches
See On Amazon #3
BETAFPV Serial ELRS F4 1S 5A AIO Brushless Flight Controller with 8MB BlackBox Support Flash via WIFI Betaflight Serial Passthrough with BT2.0 Cable Connector for 65/75mm 1S FPV Whoop Drones
Asin: B0BKPTCMKR
【8Mb Blackbox】Built-In An 8Mb Flash Memory Chip Dedicated To Blackbox Logging. It’S An Extremely Powerful Tool For Tuning And Troubleshooting An Fpv Drone..
【Technical Support & Warranty】Betafpv Has A Professional Team And Considerate After-Sales Service. If You Have Any Issues With Its Technical Or Quality, Betafpv Guarantees To Serve You!.
【Cross Shape】F4 1S 5A Aio Fc Adopts The Classic Cross Shape Design With Only 3.6G Ultralight Weight, Reasonable Layout, And Easy To Build. With A 26*26Mm Mounting Hole Size, It Is Fully Compatible With The Whoop Frame In The Current Market. Especially Suitable For The Weight Sensitive 65/75Mm Wheelbase Micro Whoop Drones..
【Gyro&Esc Hardware】We Updated The Fc With High-Quality Bmi270 Gyro And Bb51 Esc Hardware. If You Want To Setup The Esc Specification, Please Use The Blhelisuite16714902a_Beta Or Esc-Configurator..
Features
- Serial ELRS Compared to the previous version, this new board uses Serial ExpressLRS 2.4G instead of SPI ELRS 2.4G so that it can support ExpressLRS V3.0. Pilots can flash any version of ELRS RX firmware via Wi-Fi or Betaflight serial passthrough.
- Gyro&ESC Hardware We updated the FC with high-quality BMI270 gyro and BB51 ESC hardware. If you want to setup the ESC specification, please use the BLHeliSuite16714902A_Beta or ESC-Configurator.
- 8MB BlackBox Built-in an 8MB flash memory chip dedicated to Blackbox logging. It s an extremely powerful tool for tuning and troubleshooting an FPV drone.
- Cross Shape F4 1S 5A AIO FC adopts the classic cross shape design with only 3.6g ultralight weight, reasonable layout, and easy to build. With a 26*26mm mounting hole size, it is fully compatible with the whoop frame in the current market. Especially suitable for the weight sensitive 65/75mm wheelbase micro whoop drones.
- Technical Support & Warranty BETAFPV has a professional team and considerate after-sales service. If you have any issues with its technical or quality, BETAFPV guarantees to serve you!
- See more on Amazon...
Brand: BETAFPV | Manufacturer: BETAFPV
Dimensions: 0.79 x 2.17 x 2.17 inches
See On Amazon #4
BETAFPV Meteor75 Pro 1S Brushless Whoop Drone Quadcopter with 45mm 3-Blade Propellers for FPV Freestyle Racing Indoor Outdoor, Fly Time Up to 6min with BT2.0 550mAh 1S Lipo Battery-ELRS
Asin: B0BZVS49TJ | Model: 01010026_1 | PartNumber: 01010026_1
🎄【Motors&Battery】Meteor75 Pro Features Updated Powerful 22000Kv 1102 Motors And Bt2.0 550Mah 1S Battery, Which Provides A Larger Capacity And Higher Discharge Rate, Bringing More Flight Time And Robust Flight Performance To The Quadcopter..
🎄【Camera&Canopy】Built-In 1.45G Ultralight And Upgraded C03 Fpv Camera. This New Camera Has Optimal Performance For Indoor Whoop Drones. Adopted With An Injection Molding Technique, This Canopy Is 1.60G Ultralight Weight And Is More Durable, Anti-Ruin, And Heat-Resistant, Providing Good Protection For The Whoop Drone..
🎄【Fc&Esc】Equipped With F4 1S 5A Flight Controller(Serial Elrs). The Elrs Rx Version Comes With The Default Elrs V3.0 Firmware. The Esc On The Board Is Powered By Bb51 Hardware In Place Of Bb21, And The Gyro To Bosh Bmi270 For Better Performance And Stability..
🎄【Frame&Propellers】Meteor75 Pro Brushless Whoop Frame Is Built For The Largest 1S Brushless Drone Quadcopter. Featuring Motor Holders For Convenient Installation, And It Is Perfect For 45Mm Propellers. This Combo Performs Very Precisely, Agile, And Fantastic Flying. It Greatly Enhances The Thrust For 1S Whoop..
Features
- Ultra-Powerful Meteor75 Pro 1S brushless whoop quadcopter is the largest available 1S whoop on the current market. It can offer pilots a faster, more responsive flight experience, and longer flight time, which would be ideal for FPV racing or acrobatic flying indoors or outdoors.
- Frame&Propellers Meteor75 Pro brushless whoop frame is built for the largest 1S brushless drone quadcopter. Featuring motor holders for convenient installation, and it is perfect for 45mm propellers. This combo performs very precisely, agile, and fantastic flying. It greatly enhances the thrust for 1S whoop.
- Motors&Battery Meteor75 Pro features updated powerful 22000KV 1102 motors and BT2.0 550mAh 1S battery, which provides a larger capacity and higher discharge rate, bringing more flight time and robust flight performance to the quadcopter.
- FC&ESC Equipped with F4 1S 5A flight controller(Serial ELRS). The ELRS RX version comes with the default ELRS V3.0 firmware. The ESC on the board is powered by BB51 hardware in place of BB21, and the gyro to BOSH BMI270 for better performance and stability.
- Camera&Canopy Built-in 1.45g ultralight and upgraded C03 FPV camera. This new camera has optimal performance for indoor whoop drones. Adopted with an injection molding technique, this canopy is 1.60g ultralight weight and is more durable, anti-ruin, and heat-resistant, providing good protection for the whoop drone.
- See more on Amazon...
Brand: BETAFPV | Manufacturer: BETAFPV
Dimensions: 1.00 x 4.00 x 4.00 Inches
See On Amazon #5
BETAFPV ELRS LiteRadio 3 Radio Transmitter RC Controller, Support FPV Simulator, Joystick Calibration, USB Charging, Compatible for RC Models Like Multirotor Airplane FPV Drone Quadcopter - Mode 2
Asin: B09PV8C3D3 | Model: LiteRadio 3 | PartNumber: LiteRadio 3
🎄【Betafpv Configurator Supported】Literadio 3 Upgrades With Betafpv Self-Developed Customized Literadio System. Pilots Can Directly Operate The Joystick Calibration And Firmware Update On The Radio Transmitter Or Betafpv Configurator. Betafpv Configurator Is A Utility Designed To Simplify Updating, Configuring, And Tuning The Radio Transmitter. Easy And Convenient, Further Fulfilled Your Different Fly Requirement..
🎄【Please Note】The Default Firmware Of The Literadio 3 Radio Transmitter (Elrs 2.4G) Has Been Elrs V3 Since Jan 2024 Instead Of The Previous Version Elrs V2.0. Literadio 3 Radio Transmitter Elrs V3 No Longer Supports An External Tx Module ! ! !.
🎄【Fpv Simulator Supported】Literadio 3 Is Ergonomic And Has The Shape Of A Gaming Controller. The Rubber Coat Is Comfortable To Hold, And The Anti-Slip Texture On The Handles Allows For A Solid Grip. It Has The Function Of An Fpv Simulator Which Can Act As A Usb Joystick When Connected To A Pc, And Supports Most Of The Simulators On The Market With A Comprehensive Configuration..
🎄【Long Use Time】Equipped With A Built-In 2000 Mah 1S Battery And Charging Module, You Can Charge By Usb And It Can Work Up To 15 Hours Without An External Module. Meanwhile, It Designed A Low-Power Warning To Indicate A Low Battery. It Indicates A Low Battery And Needs To Be Re-Charged If The Blue Light Flashes Slowly And The Buzzer Beeps Continuously..
Features
- Nano Joystick Gimbal LiteRadio 3 has a newly designed Joystick Gimbal. With ergonomic stick ends, the stick is detachable, anti-slip, and adjustable in height, it has long longevity of up to 120k times rotations. The potentiometer is positioning accuracy and fast response sensitivity, bringing a good experience to your flight.
- Long Use Time Equipped with a built-in 2000 mAh 1S battery and charging module, you can charge by USB and it can work up to 15 hours without an external module. Meanwhile, it designed a Low-Power warning to indicate a low battery. It indicates a low battery and needs to be re-charged if the blue light flashes slowly and the buzzer beeps continuously.
- BETAFPV Configurator Supported LiteRadio 3 upgrades with BETAFPV self-developed Customized LiteRadio System. Pilots can directly operate the Joystick Calibration and Firmware Update on the radio transmitter or BETAFPV Configurator. BETAFPV Configurator is a utility designed to simplify updating, configuring, and tuning the radio transmitter. Easy and convenient, further fulfilled your different fly requirement.
- FPV Simulator Supported LiteRadio 3 is ergonomic and has the shape of a gaming controller. The rubber coat is comfortable to hold, and the anti-slip texture on the handles allows for a solid grip. It has the function of an FPV simulator which can act as a USB Joystick when connected to a PC, and supports most of the simulators on the market with a comprehensive configuration.
- Please Note The default firmware of the LIteRadio 3 Radio Transmitter (ELRS 2.4G) has been ELRS V3 since Jan 2024 instead of the previous version ELRS V2.0. LiteRadio 3 Radio Transmitter ELRS V3 no longer supports an external TX Module ! ! !
- See more on Amazon...
Brand: BETAFPV | Manufacturer: BETAFPV
Dimensions: 3.35 x 8.27 x 6.30 inches
See On Amazon #6
BETAFPV ExpressLRS Lite Receiver with Flat SMD Ceramic Antenna High Refresh Rate Long Range Performance Compatible for 65/75/85mm FPV Racing Whoop Drone
Asin: B09PR55LYF | Model: 01070004_2 | PartNumber: 01070004_2
【Expresslrs】 Expresslrs Is An Open-Source Rc Link For Rc Applications, Based On Semtech Lora Sx127x Or Sx1280 Hardware For Rx And Tx Respectively. This Makes Expresslrs One Of The Fastest Rc Links Available While Still Offering Long-Range Performance.
【Configuration & Bind】The Lite Receiver Comes With Officially Major Release V1.1.0 Protocol And No Binding Phrase Included. Lite Receiver Could Enter Binding Status By Power On/Off Three Times.
【Expresslrs Lite Receiver】Betafpv Elrs Lite Receiver Is Based On The Expresslrs Project, An Open-Source Rc Link For Rc Applications That Aims To Achieve The Best Possible Link Performance In Both Speeds, Latency, And Range Suit For Elrs Tx Module, Etc.
【Weight&Size】New Lite Receiver With A Flat Antenna Features A 3Mm Extra-Thin Board And 0.53G Lightweight, Which Requires Less Assembly Space On Drones With Limited Space.
Features
- Performance Ultralight ELRS Lite receiver has a 2.4GHz Flat SMD ceramic antenna. A solid flat antenna without irregular parts can withstand crashes, making the receiver not so fragile. Perform well in control, range and stability, bringing a good flight experience to pilots
- Weight&Size New lite receiver with a flat antenna features a 3mm extra-thin board and 0.53g lightweight, which requires less assembly space on drones with limited space
- ExpressLRS ExpressLRS is an open-source RC link for RC applications, based on Semtech Lora SX127x or SX1280 hardware for RX and TX respectively. This makes ExpressLRS one of the fastest RC links available while still offering long-range performance
- ExpressLRS Lite Receiver BETAFPV ELRS Lite receiver is based on the ExpressLRS project, an open-source RC link for RC applications that aims to achieve the best possible link performance in both speeds, latency, and range suit for ELRS TX module, etc
- Configuration & Bind The Lite receiver comes with officially major release V1.1.0 protocol and no Binding Phrase included. Lite receiver could enter binding status by power on/off three times
- See more on Amazon...
Brand: BETAFPV | Manufacturer: BETAFPV
Dimensions: 2.76 x 1.97 x 2.36 inches
See On Amazon #7
BETAFPV SuperD ExpressLRS 2.4GHz V3.0 Diversity Receiver with Two Antennas TXCO Tech Long Range Performance Support CRSF Protocol Compatible with FPV Drone Freestyle and Fixed-Wing Aircraft
Asin: B0BMLP81S8 | Model: 01070006_1 | PartNumber: 01070006_1
【Two Dipole T Antennas】Superd Elrs 2.4G Diversity Receiver Comes With Two Dipole T Antennas, It Will Create An Omnidirectional Signal For Good Signal Transmission. Placing The Antenna Separately And Vertically As Far Part As Possible To Get A Better Signal Is Recommended..
【Ultralight Weight】 Ultralight Weight Only 1.1G Without The Antenna. The Receiver Board Features A Reasonable Layout And Is Impeccably Clean. Very Easy To Solder..
【Compatible Products】Not Only It Is Used For Fpv Drones But Also For Fpv Fixed-Wing, Or Other Fpv Aircraft. It Has Superb Performance In Long Range Flying. It Greatly Fulfills The Requirements Of Reliability For Long Range Flying, Aerial Photography, Or Fpv Freestyle Tricks..
【Dual Rf Receiver Chains】Superd Elrs 2.4G Diversity Receiver With Two Complete Rf Receiver Chains (Referring To Pa+Lna+Sx1280), Ensuring Longer And More Stable Flying For Fpv Drones And Rc Airplanes. Based On The Latest Official Exprsslrs. It Comes With Expresslrs V3.0.0 Firmware..
Features
- TXCO Tech SuperD ELRS 2.4G Diversity Receiver is built-in a TCXO (temperature compensated crystal oscillator), which is shared by two RF chips for a super accurate clock source. The true diversity receiver including two RF chips and PA+LNA will generate a large amount of heat when working. With the high-quality TCXO, it can withstand extreme temperatures with no fear of heat and cold, continuously outputting accurate frequency for long range flight.
- Dual RF Receiver Chains SuperD ELRS 2.4G Diversity Receiver with two complete RF receiver chains (referring to PA+LNA+SX1280), ensuring longer and more stable flying for FPV drones and RC airplanes. Based on the latest official ExprssLRS. It comes with ExpressLRS V3.0.0 firmware.
- Two Dipole T Antennas SuperD ELRS 2.4G Diversity Receiver comes with Two Dipole T antennas, it will create an omnidirectional signal for good signal transmission. Placing the antenna separately and vertically as far part as possible to get a better signal is recommended.
- Compatible Products Not only it is used for FPV drones but also for FPV fixed-wing, or other FPV aircraft. It has superb performance in long range flying. It greatly fulfills the requirements of reliability for long range flying, aerial photography, or FPV freestyle tricks.
- Ultralight Weight Ultralight weight only 1.1g without the antenna. The receiver board features a reasonable layout and is impeccably clean. Very easy to solder.
- See more on Amazon...
Brand: BETAFPV | Manufacturer: BETAFPV
Dimensions: 0.39 x 3.94 x 2.76 inches
See On Amazon #8
BETAFPV SuperP 14CH Diversity Receiver with TCXO, 2 Antennas, Dual RX Chains Support Long Range Flying Aerial Photography FPV Freestyle Tricks, for Fixed-Wing Helicopter RC Cars Boats - ELRS 2.4G
Asin: B0CFPRQ6NZ | Model: 01070007_1 | PartNumber: 01070007_1
Built-In A Tcxo (Temperature-Compensated Crystal Oscillator), It Is Shared By Two Rf Chips For A Super Accurate Clock Source. It Can Withstand Extreme Temperatures With No Fear Of Heat And Cold, Continuously Outputting Accurate Frequency For Long-Range Flight..
Reserving A Type-C Usb Port, It Is Convenient For Pilots To Flash The Firmware. The Plug-And-Play Design Makes It Very Easy And Friendly To Use..
Two Antennas Will Create An Omnidirectional Signal For Good Signal Transmission. Placing The Antenna Separately And Vertically To Get A Better Signal Is Recommended. With The Support Of The Failsafe Function, It Is Capable Of Protecting Rc Models From Being Out Of Control..
A True Diversity Receiver With Two Complete Rf Receiver Chains (Referring To Dual Sx1280/Sx1281 Or Dual Sx1276), Based On The Latest Official Expresslrs. It Comes With Expresslrs V3.3 Firmware..
Features
- Featuring 14 PWM channels, this receiver is suitable for different applications. It can drive up to 14 servos, allowing for more complex and precise control. In addition, an external sensor such as a barometer, current sensor, etc, is also supported.
- A true diversity receiver with two complete RF receiver chains (referring to dual SX1280/SX1281 or dual SX1276), based on the latest official ExpressLRS. It comes with ExpressLRS V3.3 firmware.
- Built-in a TCXO (temperature-compensated crystal oscillator), it is shared by two RF chips for a super accurate clock source. It can withstand extreme temperatures with no fear of heat and cold, continuously outputting accurate frequency for long-range flight.
- Two antennas will create an omnidirectional signal for good signal transmission. Placing the antenna separately and vertically to get a better signal is recommended. With the support of the failsafe function, it is capable of protecting RC models from being out of control.
- Reserving a Type-C USB port, it is convenient for pilots to flash the firmware. The plug-and-play design makes it very easy and friendly to use.
- See more on Amazon...
Brand: BETAFPV | Manufacturer: BETAFPV
Dimensions: 0.79 x 5.91 x 3.94 Inches | Weight: 0.07 Pounds
See On Amazon #9
BETAFPV ELRS LiteRadio 2 SE Radio Transmitter Remote Controller with Built-in 1000mAh 1S Battery for FPV RC Racing Drones Multirotor Simulator Joystick Calibration - Mode 2 ExpressLRS V3
Asin: B09CTHBWDR | Model: LiteRadio 2 SE ELRS | PartNumber: LiteRadio 2 SE ELRS
🎄【Performance】This Elrs 2.4G Protocol Radio Transmitter Built-In 1000Mah 1S Battery, You Can Charge It By Type-C Cable Instead Of Replacing Battery. It Has A Total Of 8 Channels. Supports 3 Rf Powers Of 25Mw, 50Mw And 100Mw, And Packet Rates Of 50Hz, 150Hz, 250Hz And 500Hz.
🎄【About Bind】Please Note That The Firmware Version Of The Transmitter And The Receiver Or The Tx Module Should Be The Same One And Then Could Be Bound Together. If You Don't Know The Firmware Version, Please Contact Us Directly And We Will Solve The Problem For You..
🎄【Expresslrs 2.4G Protocol】Betafpv Expresslrs 2.4G Literadio 2 Se Radio Transmitter Comes With Built-In Elrs 2.4G Tx, Which Can Achieve Long-Range Flying With Your Drones. Please Note, The Elrs Firmware Is Elrs 3.X, It Can't Be Bound With Your Equipment With Elrs 2.X Version..
🎄【Fpv Simulator】This Transmitter Has The Function Of Fpv Simulator Like Other Versions Of Literadio 2, Which Can Act As A Usb Joystick When Connected To A Personal Computer, Suitable For Fpv Novices To Play Fpv Simulators Like Ereadrone.
🎄【Betafpv Configurator】This Transmitter Supported Betafpv Configuration With The Function Of Radio Controller Setup, Full Function Of The Expresslrs Configuration, Channel Mixer For Fix Wing Drones, And Firmware Update.
Features
- Firmware Version This LiteRadio 2 SE Transmitter's firmware is ELRS V3, it can't be bound with your equipment with ELRS 2.X version. Please make sure the receiver or the TX module has same firmware version and then could be bound together. If you don't know the firmware version, please contact us directly and we will solve the problem for you.
- BETAFPV Configurator This transmitter supported BETAFPV Configuration with the function of radio controller setup, Full function of the ExpressLRS configuration, Channel mixer for fix wing drones, and firmware update
- Performance This ELRS 2.4G protocol radio transmitter built-in 1000mAh 1S battery, you can charge it by type-c cable instead of replacing battery. It has a total of 8 channels. Supports 3 RF powers of 25mW, 50mW and 100mW, and packet rates of 50Hz, 150Hz, 250Hz and 500Hz
- FPV Simulator This transmitter has the function of FPV simulator like other versions of LiteRadio 2, which can act as a USB Joystick when connected to a personal computer, suitable for FPV novices to play FPV simulators like EREADRONE
- About Bind Please note that the firmware version of the Transmitter and the receiver or the TX module should be the same one and then could be bound together. If you don't know the firmware version, please contact us directly and we will solve the problem for you.
- ExpressLRS 2.4G Protocol BETAFPV ExpressLRS 2.4G LiteRadio 2 SE radio transmitter comes with built-in ELRS 2.4G TX, which can achieve long-range flying with your drones. Please note, The ELRS firmware is ELRS 3.X, it can't be bound with your equipment with ELRS 2.X version.
- See more on Amazon...
Brand: BETAFPV | Manufacturer: BETAFPV
Dimensions: 3.15 x 6.50 x 4.72 inches
See On Amazon #10
BETAFPV 4pcs Lava 450mAh 1S 3.8V 75C LiHV FPV Lipo Battery with BT2.0 Connector for 1-2S FPV Tiny Whoop Drone Quadcopters Like Meteor75, Meteor75 Pro, Cetus Pro 1S Brushless Drones, Cetus X 2S Quad
Asin: B0CPDJYCGB
【Performance】With An Extended Battery Cycle Life, It Ensures Prolonged Power Support, Bringing Users Sustained And Reliable Performance..
【Suitable】 Lava 1S 450Mah Lipo Battery Is Suitable For 1-2S Fpv Tiny Whoop Drone Like Cetus Pro, Cetus X, Meteor75, Meteor75 Pro And Other 1-2S Fpv Racing Drone..
【Design】Lava 1S 450Mah Lipo Battery Comes With Bt2.0 Connector And Features A New Design That Symbolizes Explosive Power Akin To Molten Lava..
【High C-Rate】With A Boosted Discharge Rate Of 75C, It Provides Greater Burst Power For Superior Flight Performance And Maneuverability For Unparalleled Control..
Features
- Z-Folding Process LAVA series batteries feature a Z-Folding Process, which enables efficient high-current discharge within shorter time frames, resulting in elevated discharge platforms. Compared to the Winding Process, it achieves a 0.2V higher discharge platform under equivalent loads and boasts a 5% higher energy density within the same volume, extending flight time and reducing battery replacement inconvenience.
- High C-Rate With a boosted discharge rate of 75C, it provides greater burst power for superior flight performance and maneuverability for unparalleled control.
- Performance With an extended battery cycle life, it ensures prolonged power support, bringing users sustained and reliable performance.
- Design LAVA 1S 450mAh Lipo Battery comes with BT2.0 connector and features a new design that symbolizes explosive power akin to molten lava.
- Suitable LAVA 1S 450mAh Lipo Battery is suitable for 1-2S FPV Tiny Whoop drone like Cetus Pro, Cetus X, Meteor75, Meteor75 Pro and other 1-2S FPV racing drone.
- See more on Amazon...
Brand: BETAFPV | Manufacturer: BETAFPV
Dimensions: 0.28 x 2.36 x 0.63 inches
See On Amazon #11
HappyModel ELRS Module ES24TX Pro 1000mW 2.4G ExpressLRS Micro TX Module RGB LED Module for TX16S, QX7, TX12, X9D Transmitter Remote Control Drone Remote Accessories
Asin: B09MQHJSBB | Model: ES24TX Pro | PartNumber: ES24TX Pro | Ean: 0755454783022 | UPC: 755454783022
Note: This Micro Tx Module Support Most Of The Opentx Radio Transmitter Remote Controller That With Micro Jr Bay, Such As Tx16s, Tx12, Taranis X9d.
Please Make Sure The Applicability Before Purchasing, We Are Always Here To Assist..
Max Output Up To 1000Mw, Reserved Cooling Fan And Rgb Led Module. This Micro Tx Module Support Most Of The Opentx Radio Transmitter That With Micro Jr Bay. And This Time The Es24tx Pro Module Comes Completely Assembled Before Out Of Factory..
Features
- The ES24TX Pro Micro ExpressLRS TX module is a upgrade version of ES24TX module.
- Max output up to 1000mw, reserved Cooling Fan and RGB LED module. This Micro TX module support most of the OpenTX radio transmitter that with Micro JR bay. And this time the ES24TX Pro module comes completely assembled before out of factory.
- Note: This Micro TX module support most of the OpenTX radio transmitter remote controller that with Micro JR bay, such as TX16S, TX12, Taranis X9D
- Please make sure the Applicability before purchasing, we are always here to assist.
- See more on Amazon...
Brand: HAPPYMODEL | Manufacturer: HappyModel
See On Amazon #12
BETAFPV Meteor75 1S Micro FPV Whoop Drone Quadcopter for FPV Racing Freestyle Flight Indoor Outdoor Fly Up to 6 Minutes with F4 1S 5A Flight Controller 0802SE 19500KV Motor C03 Camera - ELRS
Asin: B0BMVG1J1T | Model: 01010023_1 | PartNumber: 01010023_1
【Power System】By Using The Latest 0802Se 19500Kv Motors And 40Mm 2-Blade Props, Which Provides Pilots With Stronger Experience Of Powerful Indoor And Outdoor Flight. The Newest Motor Makes The Perfect Dynamic Balance, Which Gives The Drone More Flexibility And Longer Flying Time, Which Is Perfect For The Weight-Sensitive 75Mm Brushless Whoop Drone..
【Meteor75 Frame】Meteor75 Frame Weighs Only 5.68G And Is Durable Enough. The Battery Slot Is Closer To The Center Of Gravity For A Smoother Flying Experience, And You Will Land On The Motor Screws Instead Of The Battery..
【Camera&Canopy】Built-In 1.52G Ultralight Weight C03 Camera, Offer A High-Quality, Clear And Sharper Images To Pilots. Adopted With A Injection Molding Canopy Which Only 1.60G, More Durable, Anti-Ruin, And Heat-Resitant, Gives Your Whoop Drone A Good Protection..
【F4 1S 5A Fc】The Flight Controller Of Meteor75 Has Been Upgraded To F4 1S 5A Serial Elrs V3.0, Which Can Be Updated Via Wi-Fi Or Betaflight Serial Passthrough. Pilots Can Flash Any Version Of Elrs Rx Firmware Without Updating Fc Firmware. With A High-Quality Bmi270 Gyro And Bb51 Esc Hardware. In Addition, This New Board Supports The Betaflight Blackbox Function..
Features
- Upgraded Meteor75 Meteor75, 1S lightweight whoop drone comes back with a completely new look. Equipped with the BT2.0 connector, the lightest F4 1S 5A FC, new 0802SE 19500KV motors, and a C03 FPV camera. With the combination of those electronics and parts, it reaches the best balance between performance, weight, durability, and premium build design.
- F4 1S 5A FC The flight controller of Meteor75 has been upgraded to F4 1S 5A Serial ELRS V3.0, which can be updated via Wi-Fi or Betaflight serial passthrough. Pilots can flash any version of ELRS RX firmware without updating FC firmware. With a high-quality BMI270 gyro and BB51 ESC hardware. In addition, this new board supports the Betaflight Blackbox function.
- Power System By using the latest 0802SE 19500KV motors and 40mm 2-blade props, which provides pilots with stronger experience of powerful indoor and outdoor flight. The newest motor makes the perfect dynamic balance, which gives the drone more flexibility and longer flying time, which is perfect for the weight-sensitive 75mm brushless whoop drone.
- Camera&Canopy Built-in 1.52g ultralight weight C03 camera, offer a high-quality, clear and sharper images to pilots. Adopted with a injection molding canopy which only 1.60g, more durable, anti-ruin, and heat-resitant, gives your whoop drone a good protection.
- Meteor75 Frame Meteor75 frame weighs only 5.68g and is durable enough. The battery slot is closer to the center of gravity for a smoother flying experience, and you will land on the motor screws instead of the battery.
- See more on Amazon...
Brand: BETAFPV | Manufacturer: BETAFPV
Dimensions: 2.56 x 5.12 x 5.12 Inches
See On Amazon #13
HAPPYMODEL ELRS 2-4G ExpressLRS EPI/EP2 RX Nano Long Range Receiver SX1280 EXPRESSLRS for Racing Drone (EP2 RX)
Asin: B0BLZ12GSK
Peak-Gain Difference: Ep2 _Rx Is 3.7Db, While Ep1_Rx Is 2.23Db..
Elrs Receiver Comfortable With Racing, Long Range Dorne And Tinywhoop, As They Are Lightweight , Nano Size, And With Low-Latency And High-Refresh-Rate Rf Module..
Receiver Common Feature: Working Voltage 5V , Dimension 10*10*6Mm, Sx1280imltrt Rf Module, Receive Refresh Rate: 25- 500, Type: Ism..
Mcu: Ep1 / Ep2_Rx With Esp8285 Mcu. Frequency Range: 2400 To 2500..
Features
- The Happymodel 2-4G ELRS nano series receiver is an open source program based on ExpressLRS, pre-loaded firmware are all beta versions.
- MCU: EP1 / EP2_RX with ESP8285 MCU. Frequency Range: 2400 to 2500.
- Peak-Gain Difference: EP2 _RX is 3.7dB, while EP1_RX is 2.23dB.
- Receiver Common Feature: Working Voltage 5V , Dimension 10*10*6mm, SX1280IMLTRT RF Module, Receive Refresh Rate: 25- 500, Type: ISM.
- ELRS Receiver Comfortable with racing, long range dorne and tinywhoop, as they are lightweight , Nano size, and with Low-latency and high-refresh-rate RF module.
- See more on Amazon...
Brand: HAPPYMODEL | Manufacturer: HAPPYMODEL
See On Amazon #14
0.44g Tiny 2.4GHz ExpressLRS EP2 Elrs Nano Receiver with Built-in Ceramic Antenna Long Range Low Latency for Micro Carbon Fiber FPV Racing Quadcopter Quad Frame kit RC Drone Frame Tiny Whoop
Asin: B0962M9GS6
Low Latency And High Refresh Rate, They Are Very Suitable For Fpv Racing And Long Range Fpv Cruising While Being Ultra-Light And Ultra-Small, Making Them Very Suitable For Tinywhoop..
Weight: 0.44G (With Built-In Ceramic Antenna), The Main Difference Between Ep1 And Ep2 Receiver Is That Ep2 Has Built-In Ceramic Antenna, Making It More Compact And No Need To Attach External Antenna..
With This Tiny Teeny Receiver You Can Achieve Great Range Even Comparable To Crossfire Or Tracer, Ghost. Don't Just Take My Word For It, Search Crossfire Vs Expresslrs On Youtube And Hear What Joshua Bardwell Have To Say..
To Flash The Firmware, Power Up The Receiver While Keeping The Transmitter Turned Off. After A While, You Can Find The Expresslrs Hotspot. Connect To This Hotspot Using A Pc Or Mobile Phone. The Password Is Expresslrs, Then You Can Visit 10.0.0.1 To Upload The Firmware.
Features
- Happymodel 2.4GHz ELRS Nano series receiver is based on ExpressLRS open source architecture and program, Based on PP RX, we developed the ESP8285 version of Nano 2.4GHz rx, named EP1 and EP2. The RF module of EP1/EP2 is the same as PP RX, but it uses ESP8285 MCU. Therefore, you can upgrade the firmware via WIFI, which is very user-friendly.
- To flash the firmware, Power up the receiver while keeping the transmitter turned off. After a while, you can find the ExpressLRS hotspot. Connect to this hotspot using a PC or mobile phone. The password is expresslrs, then you can visit 10.0.0.1 to upload the firmware
- Low latency and high refresh rate, they are very suitable for FPV racing and long range FPV cruising while being ultra-light and ultra-small, making them very suitable for Tinywhoop.
- With this tiny teeny receiver you can achieve great range even comparable to crossfire or Tracer, ghost. Don't just take my word for it, search Crossfire vs expresslrs on youtube and hear what Joshua Bardwell have to say.
- Weight: 0.44g (with built-in ceramic antenna), the main difference between EP1 and EP2 receiver is that EP2 has built-in ceramic antenna, making it more compact and no need to attach external antenna.
- See more on Amazon...
Brand: Usmile | Manufacturer: Usmile
See On Amazon #15
BETAFPV Beta75X HD Brushless Whoop Drone TBS Crossfire Rx 2-3S Quadcopter with F4 2-4S AIO 12A FC Turtle V2 Camera OSD Smart Audio 1103 8000KV Motor XT30 Connector for Micro Whoop Drone FPV Racing
Asin: B07WMFSQ89 | Ean: 0724779301211 | UPC: 724779301211
Features
- True acro performance in a whoop The new Beta75X HD (along with its bigger brother the new Beta85X 4K) ushers in a new era of 3S whoop drones. With a huge improvement in power-to-weight ratio you can now fly real acro yet still enjoy the convenience safety and quietness of a whoop-sized frame.| Dialed-in tuning Running the high-performance STM32F411CEU6 processor flight controller board and finely tuned with BETAFPVF411 fly like a pro right out of the box.| Superb video Capture high-quality video and high-definition DVR recordings with the Caddx Turtle V2 on Beta75X HD version (4K on the Beta85X 4K!).| Tough and agile The custom frame is both durable and light. It weighs in at only 57.6g. The setup coupled with a 3S battery will provide a punch that ll put an ear-to-ear grin on your face.| Fiddle less fly more All-in-one and ready to fly just plug-and-rip! The custom 1103 8000KV motors come with cable connectors so if you can plug in a battery then you can start to fly.| 3S power and performance Engineered to perform best with 300mAh 3S battery.| Bright lights Look at all the pretty lights! Custom slot allows you to slap on our LED strip hassle free. Light it up!|Weight:57.6g (without battery)|Motors: 1103 8000KV motor with connector|Props: 40mm 4-blades props 1.5mm shaft hole |Camera: CADDX Turtle V2 ( for HD DVR version) |Canopy: Canopy for Beta75X (HD DVR) |Receiver Option: Frsky XM+ / DSMX / Futaba S-FHSS / Flysky |Frame: Beta75X Frame |Recommend battery: 300mAh 3S 45C Battery (Not including) |CPU: STM32F411CEU6 (100MHZ )|Six-Axis: MPU6000 (SPI connection)|Size: 26mm x 26mm whoop mounting pattern|Firmware version: BETAFPVF411(BEFH) |OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)|Receiver: Support Frsky XM/XM+ Receiver/ Futaba Receiver/ Flysky Receiver/ TBS Crossfire Receiver. Add Frsky R9M Receiver and DSMX receiver since V1.2|Support programmable LED like WS2812|Built-in current sensor|Weight: 5.6g|Support BLheli/BLHELI_S suite Pass-through ready|Support PWM Oneshot125 Oneshot42 Multishot Dshot150 Dshot300 Dshot600|Input voltage: 2S-4S Lipo|Continue current: 12A|Peak current: 13A|Firmware: BLHELI_S|Processor: SILABS EFM8BB21F16G|Motor Connectors: 1.25mm header pins connector|Factory firmware: G-H-30-16.7|Output power: 25mW and 200mW (Adjustable)|Smart Audio function is included for radio control|Frequency: 5.8GHz 6 bands 48 channels with Raceband: 5362~5945MHz|Caddx Turtle V2 camera|TV System: NTSC|Aspect Ratio: 16:9(non-changeable)|Image sensor: 1 / 2.7" CMOS sensor|1 * Beta75X BNF 3S Whoop Quadcopter (without battery)|1 * Spare 40mm 4-blades props (2CW+2CCW)
- See more on Amazon...
Brand: BETAFPV
See On Amazon #16
Betafpv Micro FPV Drone - Beta95X V3 Frame Kit
Asin: B08RDHYTMG | Model: BETA95XV3 | PartNumber: BETA95XV3 | Ean: 0725683121438 | UPC: 725683121438
Beta95x V3 Frame Also Comes With An Eva Foam Cushioning Design To Give Pilots More Safety Flying..
Equipped With A Shock Mitigation System, This Frame Kit Can Carry A Lightweight Camera Like Smo 4K Camera, And Eliminate The Shake Of The Camera. It Makes The Camera More Stable On The Flight, Which Ensures Pilots Can Capture All The Beautiful Moments Of Flight With The Stabilized And Clear Video..
Compared With The Beta95x V2 Frame, V3 Frame Kit Maintain The "Pusher Style" Design But Has Higher Durability, A Concise Appearance And Easier For Installation..
Made Of High-Quality Pa12 Material, Beta95x V3 Frame Kit Has High Abrasion Resistance, Toughness, Showing Excellent Impact Resistance In Drop & Impact Tests, It Also Can Dampen Noise And Vibrations, Bringing A More Durable Flight And No Fear Of Damage..
Features
- Built-in carbon fiber for flight controller and reserve a storage room for the antenna, Beta95X V3 frame has a more concise appearance and more convenient for installation.
- Made of high-quality PA12 material, Beta95X V3 frame kit has high abrasion resistance, toughness, showing excellent impact resistance in drop & impact tests, it also can dampen noise and vibrations, bringing a more durable flight and no fear of damage.
- Beta95X V3 frame also comes with an EVA foam cushioning design to give pilots more safety flying.
- Compared with the Beta95X V2 frame, V3 frame kit maintain the pusher style design but has higher durability, a concise appearance and easier for installation.
- Equipped with a shock mitigation system, this frame kit can carry a lightweight camera like SMO 4K camera, and eliminate the shake of the camera. It makes the camera more stable on the flight, which ensures pilots can capture all the beautiful moments of flight with the stabilized and clear video.
- See more on Amazon...
Brand: HOBBYMATE | Manufacturer: BETAFPV
Dimensions: 2.36 x 4.72 x 3.15 inches
See On Amazon #17
BETAFPV Beta75X HD Digital VTX 3S Cinewhoop Drone Frsky FCC with F4 AIO 12A FC 8000KV 1103 Motor Nebula Nano Camera XT30 Connector for CineWhoop Drone FPV Racing
Asin: B08K8VWT66
【New Canopy】Installed With The Specially Designed Hd Digital Vtx Canopy Looks Like Knight Helmet, Which Is Light And Durable. With An Adjustable Tilt Angle Of 25-45 Degree, It Can Further Fulfill The Different Requirement Of Recording To Offer Pilots A Better Fly Experience.
【Frame&Battery】Adopted With The Upgraded Beta75x V2 Frame, Which Is Durable And Stable. Increased The Height Of Whoop Loop To Protect The Props Better. Highly Recommend Betafpv 300Mah 3S S Version 45C Battery For Beta75x Hd Digital Vtx Drone.
【F4 Aio 12 Fc&Motors】Perfectly Match With F4 Aio 12A Fc And 8000Kv 1103 Brushless Motors, Definitely Supports Your Beta75x Hd Digital Vtx Cinewhoop Drone To 3S Power. Provides Pilots A High Speed And Reliable Power.
【Nebula Nano Kit】Equipped With The Modified Nebula Nano Kit To Further Lose The Weight Of Drone. This Lightweight Kit Provides A Stable Fpv Picture And Long Transmission Distance, Greatly Brings You A High Quality, Unique Flight Experience.
Features
- HD Digital VTX Whoop It is an ultralight HD Digital VTX cinewhoop drone, weighs only 54.7g without battery, with 75mm wheelbase. Small, dynamic but powerful enough, pilots can do all FPV freestyle tricks easily
- Nebula Nano Kit Equipped with the modified Nebula Nano kit to further lose the weight of drone. This lightweight kit provides a stable FPV picture and long transmission distance, greatly brings you a high quality, unique flight experience
- New Canopy Installed with the specially designed HD digital VTX canopy looks like knight helmet, which is light and durable. With an adjustable tilt angle of 25-45 degree, it can further fulfill the different requirement of recording to offer pilots a better fly experience
- F4 AIO 12 FC&Motors Perfectly match with F4 AIO 12A FC and 8000KV 1103 brushless motors, definitely supports your Beta75X HD Digital VTX cinewhoop drone to 3S power. Provides pilots a high speed and reliable power
- Frame&Battery Adopted with the upgraded Beta75X V2 frame, which is durable and stable. Increased the height of whoop loop to protect the props better. Highly recommend BETAFPV 300mAh 3S S version 45C battery for Beta75X HD Digital VTX drone
- See more on Amazon...
Brand: BETAFPV | Manufacturer: BETAFPV
Weight: 0.12 pounds
See On Amazon #18
For BETAFPV F4 1S 5A For AIO Brushless Flight Controller Built-in For SPI ExpressLRS For ELRS 2.4G Receiver for FPV Racing Drone Meteor 65/75 Drone Parts
Asin: B0CL4KM159 | Ean: 8135275915642
Compared To The Previous Version, The New Board Uses Serial Expresslrs 2.4G Instead Of Spi Elrs 2.4G So That It Can Support Expresslrs V3.0 And Also Has A Frsky Rx Version To Choose From..
Made Of High-Quality Material, And Less Burrs And Good Texture. And With Better Wear Resistance, The Life Time Can Be Longer..
We Updated The Fc With High-Quality Bmi270 Gyro And Bb51 Esc Hardware. In Addition, This New Board Supports The Betaflight Blackbox Function..
The Ultralight F4 1S 5A Aio Brushless Flight Controller Is Back In Stock With New And Upgraded Features..
Features
- Made of high quality material, durable and practical to use.
- The ultralight F4 1S 5A AIO Brushless Flight Controller is back in stock with new and upgraded features.
- Compared to the previous version, the new board uses Serial ExpressLRS 2.4G instead of SPI ELRS 2.4G so that it can support ExpressLRS V3.0 and also has a Frsky RX version to choose from.
- We updated the FC with high-quality BMI270 gyro and BB51 ESC hardware. In addition, this new board supports the Betaflight Blackbox function.
- Made of high-quality material, and less burrs and good texture. And with better wear resistance, the life time can be longer.
- See more on Amazon...
Brand: HePbak | Manufacturer: HePbak
Weight: 0.00 Pounds
See On Amazon
Looking For Something Else?
Search