FYSETC 3D Printing Buildplate 300x300mm/11.8x11.8 inch Steel Spring Sheet Bed Printing Hotbed Parts Steel Plate with PEI + Sticker Surface for TAZ 6 Ender 6
Asin: B08C77H5JZ
As an Amazon Associate we earn a fee from qualifying purchases when you follow a link to Amazon from this page. We rank the products, but the links to Amazon are promotional.Our Sticker And Films Have All Been Formulated To Resist Over 130℃ / 226F So You Can Heat Your Bed To High Temps For Specialty Filaments And Not Worry About Loss Of Performance.
Before Printing, Please Remove The Protect Film Which Stick On The Pei Surface, So If You Received Package But Found The Air Bubbles Or Scratches, Please Don't Worry, They Are The Surface Layer, Pei Will Not Be Affected..
The Pei Has Been Pasted, If Pei Is Damaged During Use, You Can Tear It Off From The Steel Plate And Purchase The Pei Separately To Replace It. After Printing Or Before Printing, Use Steel Wool Pads With Detergent To Clean The Pei Sheet, Will Keep The Pei Like New, Give The Pei More Life. But Be Make Sure The Hotbed Is Cold..
Size:300 X 300Mm/11.8X11.8 Inch, Please Re-Measure Your Build Plate, Don't Refer To Build Volume.Fits: Taz Workhorse, Taz Pro, Taz 6, Taz 5, Taz 4, Taz 3, May Fit: A8 Plus, Et5 And Et5 Pro, Ender 6（290X290mm）.
Features
- This PEI Flexible Heated Bed is combined with 2 parts: a flexible steel platform sticking with a pei sheet on one side + a sticker bottom sheet with adhesive on the back. The PEI comes pre applied. If want to leave a frosted bottom on your print, please search our double-sided textured pei powder(Asin: B07V9DY7SM / B088TBZSV6 ) at the shop.
- Size:300 x 300mm/11.8x11.8 inch, please re-measure your build plate, don't refer to build volume.Fits: TAZ Workhorse, TAZ Pro, TAZ 6, TAZ 5, TAZ 4, TAZ 3, may fit: A8 plus, et5 and et5 pro, Ender 6 290x290mm
- Our sticker and films have all been formulated to resist over 130 / 226F so you can heat your bed to high temps for specialty filaments and not worry about loss of performance
- The PEI has been pasted, If PEI is damaged during use, you can tear it off from the steel plate and purchase the PEI separately to replace it. After printing or before printing, use steel wool pads with detergent to clean the PEI sheet, will keep the PEI like new, give the PEI more life. but be make sure the hotbed is cold.
- Before printing, Please remove the protect film which stick on the PEI surface, so if you received package but found the air bubbles or Scratches, please don't worry, they are the surface layer, PEI will not be affected.
- See more on Amazon...
Brand: FYSETC | Manufacturer: fuyuansheng
See On Amazon Similar To FYSETC 3D Printing Buildplate 300x300mm
#1
Creality Ender 3 Max Neo Bed Upgrade, PEI Sheet 310 x 320mm Removable Magnetic Flexible Texture Surface Heated Bed Plate Build Surface for CR-10S PRO/CR-10 V2/ CR-10 V3/ CR-X/CR-X Pro/Ender-3 Max
Asin: B0BL337VZL | Model: 3D-PEI-320x310 | PartNumber: 3D-PEI-320x310
【Great Adhesion & Easy Take Mold】Print Molds Onto Pei Build Plate Frosted Texture Surface Directly. No Tape, No More Glue, Release Your Printing Anxiety. With A Magnetic Printing Pei Sheet Plate, You Only Need To Remove It From The Bed And Bend It, Then The Mold Can Be Removed. When You Let Go, They Just Return Back To Shape And Will Not Break Easily. No Need To Scratch, Pry And Damage Your Prints!.
【After Sales Support】We Provide Professional After-Sales Service. Please Kindly Contact Us(Seller) Via "Ask A Question" Find Us Directly Cause Our Customer Service Will Respond To You Within 24 Hours No Matter What The Question..
【Simple Installation】Our Pei Steel Sheet Is Easy To Install And The Installation Time Is Less Than 2 Minutes. Just Need To Place The Bottom 3M Adhesive Surface On Top Of The No-Heated Bed. The Steel Pei Plate Can Be Magnetically Bonded To The Magnetic Sticker..
【Wide Application】Compatible With Pla/ Petg/ Peek/ Abs And Any Other Filaments. 310*320Mm Spring Steel Sheet 3D Printer Bed Works Well With Cr-10S Pro/ Cr-10 V2/ Cr-10 V3/ Cr-X/ Cr-X Pro/ Cr-10S Pro V2/ Ender-3 Max/ Ender-3 Max Neo And Other Same-Sized Beds..
Features
- Quality assurance 100% Official Creality 3D printer PEI Sheet 310*320mm removable magnetic flexible Texture heated bed platform. Gold PEI surface is of strong high-temperature stability, flame retardant, heat resistance, high strength, wear resistance, and good printing stability.
- Wide Application Compatible with PLA/ PETG/ PEEK/ ABS and any other filaments. 310*320mm spring steel sheet 3d printer bed works well with CR-10S PRO/ CR-10 V2/ CR-10 V3/ CR-X/ CR-X Pro/ CR-10S PRO V2/ Ender-3 Max/ Ender-3 Max Neo and other same-sized beds.
- Great Adhesion & Easy Take Mold Print molds onto PEI build plate frosted texture surface directly. No tape, no more glue, release your printing anxiety. With a magnetic printing PEI sheet plate, you only need to remove it from the bed and bend it, then the mold can be removed. When you let go, they just return back to shape and will not break easily. No need to scratch, pry and damage your prints!
- Simple Installation Our PEI steel sheet is easy to install and the installation time is less than 2 minutes. Just need to place the bottom 3M adhesive surface on top of the no-heated bed. The steel PEI plate can be magnetically bonded to the magnetic sticker.
- After Sales Support We provide professional after-sales service. Please kindly contact us(seller) via ask a question find us directly cause our customer service will respond to you within 24 hours no matter what the question.
- See more on Amazon...
Brand: Creality | Manufacturer: Creality 3D
See On Amazon #2
Official Creality Ultra-Flexible Removable Magnetic 3D Printer Build Surface Heated Bed Cover for CR-10/CR-10S/Ender 3 Max/Ender 3 Max Neo/SV06 Plus/SV04 IDEX/Longer LK5 Pro 3D Printer 310X310MM
Asin: B07JFH3MFK | Model: CR-10-Magnetic | PartNumber: CR-10-Magnetic | Ean: 0667797511692 | UPC: 667797511692
Customizable: The Flexible Surface Can Easily Be Cut To Any Demensions Making It Perfect For All Build Sizes And All Fdm Printer Models..
Universal: Works With All Fdm Printer Models, And All Heated And Non-Heated 3D Printer Beds..
Simple Installation: Build Surface Comes With Upper Magnetic Build Surface And Lower Magnetic Adhesive Base. Place Lower 3M Adhesive Surface On Top Of Normal Build Plate.
Easy Model Removal: The First 3D Printing Surface Designed With Model Removal In Mind. This Surface Is Easily Removed, And Flexible. Simply Print On The Surface, Remove The Upper Magnetic Surface From The Lower, Bend The Flexible Surface And Watch The Model Fall Right Into Your Hands.
Features
- ALL NEW FUNCTIONALITY: Introducing the first ever removable, magnetically secured, build surface for hassle free model removal. Say goodbye to all those removal tools, spatulas, and knives with this genius design
- EASY MODEL REMOVAL: The first 3D printing surface designed with model removal in mind. This surface is easily removed, and flexible. Simply print on the surface, remove the upper magnetic surface from the lower, bend the flexible surface and watch the model fall right into your hands
- CUSTOMIZABLE: The flexible surface can easily be cut to any demensions making it perfect for all build sizes and all FDM printer models.
- SIMPLE INSTALLATION: Build surface comes with upper magnetic build surface and lower magnetic adhesive base. Place lower 3M adhesive surface on top of normal build plate
- UNIVERSAL: Works with all FDM printer models, and all heated and non-heated 3D printer beds.
- See more on Amazon...
Brand: Creality | Manufacturer: Creality 3D
Weight: 0.93 Pounds
See On Amazon #3
FYSETC Prusa Build Plate MK52 MK3S+ MK4 Spring Steel Surface: Textured PEI+ PET-CF Double-Sided Flexible PEI Sheet 253.8x241mm Hot Bed Cover for Filament PLA ABS for MK2 MK2.5 MK3 MK3S 3D Printer
Asin: B0BLNRQ2QW
3. Solution For First Layer Adhesion: **Do Not Sand On This Carbonpet Bed To Avoid Permanent Damage.** No Glue, No Tap, Adjusting An Appropriate Z Value Is Very Important, Here My Setting Value Is -0.945 For Reference, If Too Low Causing A Filament Buildup And Easily Scratch The Print Bed. Too High The Prints Come Off The Build Plate, Can't Stick Onto The Hotbed. Key Factors For A Good Layer: Turn Off The Fan And Slow Down The Speed To 100 When Printing. A Roll Of Dry Filament Also Helps..
5. Good Quality: Made Of High Quality Stainless Steel, Flexible, Removable, High Strength And Heat Resistance, Three-Layer Design, Thicker And More Durable. Textured Pei Powder Side Can Easily Handle Temperatures Up To 190°C And Carbonfiber Side Can Work With Temperature Up To 100℃. It's Easy To Remove The Printed Matter From The Platform By Bending Slightly. Through Hundreds Of Experimental Tests, Repeated Use Is Still As New..
4. Applicable Model: Size: 253.8X241mm/10X9.48 Inch, Compatible With Prus I3 Mk52 Mk2.5 Mk3 Mk3s That Has The Magletic Hotbed Itself. Please Re-Measure Your Hoted Bed Before Ordering, Not Rely The Machine's Build Volume Which Is Smaller Than That Of The Bed..
2. Double Sided Build Plate: One Side Textured Pei Powder(Gold) + Another Coated Pet-Carbonfiber Sheet, Gives You Two Different Experiences On One Plate Just By Flipping It Over. The Matte Texture Makes It Easier For The Printing Material To Adhere To The Surface, Especailly For Abs. So Does The New Side. It Leaves A Smooth Finish Inside With The Beautiful-Texture Finish. The Pet-Cf Surface Has Grids To Help Observe Nozzle Positioning Easily..
Features
- 1.Upgrade 3d printing surface: A newest Janusbps printing platform for MK52 - MK3 - MK3S - MK3S+ -MK4 3D printer, Textured PEI Powder (Gold) + PET-CF Coating sheet(Black), both sides can be used. Compatible with various kinds of 3d printing material, such as PLA, PETG, ABS, TPU, TPE, HIPS, PA-CF, WOOD etc. Recommend ABS on the Powder-coated bed.
- 2. Double sided Build Plate: One side textured pei powder(Gold) + another coated PET-Carbonfiber sheet, gives you two Different experiences on one plate just by flipping it over. The matte texture makes it easier for the printing material to adhere to the surface, especailly for ABS. So does the new side. It leaves a smooth finish inside with the beautiful-texture finish. The PET-CF surface has grids to help observe nozzle positioning easily.
- 3. Solution for first layer adhesion: **Do Not sand on this CarbonPET bed to avoid permanent damage.** No glue, No tap, Adjusting an Appropriate Z value is very important, here my setting value is -0.945 for reference, if too low causing a filament buildup and easily scratch the print bed. Too high the prints come off the build plate, can't stick onto the hotbed. Key factors for a good layer: Turn off the fan and Slow down the speed to 100 when printing. A roll of dry filament also helps.
- 4. Applicable Model: Size: 253.8x241mm/10x9.48 inch, compatible with Prus i3 MK52 MK2.5 MK3 MK3s that has the magletic hotbed itself. Please re-measure your hoted bed before ordering, not rely the machine's build volume which is smaller than that of the bed.
- 5. Good Quality: Made of high quality stainless steel, Flexible, removable, high strength and heat resistance, Three-Layer design, thicker and more durable. Textured PEI Powder side can easily handle temperatures up to 190 C and Carbonfiber side can work with temperature up to 100 . It's easy to remove the printed matter from the platform by bending slightly. Through hundreds of experimental tests, repeated use is still as new.
- See more on Amazon...
Brand: FYSETC | Manufacturer: Fuyuansheng
See On Amazon #4
Creality PEI Printing Plate Kit, Spring Steel Platform with Textured PEI Surface, Magnetic Plate Printing Hotbed Parts for Ender-3 Max/CR-10S Pro/CR-10 V3/CR-10 V2/CR-X/CR-X Pro 320 * 310 * 2mm
Asin: B0C6T9MDWT
【Easy Mold Removal】 The Composite Magnetic Material Is Non-Demagnetizing And Easy To Hang And Pick Up. All You Need To Do Is Remove The Surface Of The Build Plate And Bend It Slightly Over And Over Again To Remove The Print Directly. No Need To Scratch, Pry Or Damage The Print!.
【Compatibility】 This Platform Bed Is Compatible With The Following 3D Printers: Ender-3 Max, Cr-10S Pro, Cr-10 V2, Cr-10 V3, Cr-X, Cr-X Pro, Cr-10S Pro V2..
【Customer Service And Compatibility】 320 * 310 * 2Mm Magnetic Bed. This Pei Printing Plate Kit Is Suitable For Cr-10 Series Printers. If You Encounter Any Issues, Please Contact Us Through Amazon. We Will Reply To You Within 24 Hours!.
【Super Strong Adhesion】Soft Magnetic Stickers With Strong Magnetism/Adhesion Can Print Molds Directly On The Frosted Textured Surface Of Pei Building Boards. No Need For Tape And Glue..
Features
- Heat/Wear Resistant Genuine PEI powder coating is heat resistant. Hardened steel spring plate, 200 C resistance, no deformation. PEI Printing Plate has strong high temperature stability, flame retardancy, high abrasion resistance and good print stability.
- Super Strong Adhesion Soft magnetic stickers with strong magnetism/adhesion can print molds directly on the frosted textured surface of PEI building boards. No need for tape and glue.
- Easy Mold Removal The composite magnetic material is non-demagnetizing and easy to hang and pick up. All you need to do is remove the surface of the build plate and bend it slightly over and over again to remove the print directly. No need to scratch, pry or damage the print!
- Customer Service and Compatibility 320 * 310 * 2mm magnetic bed. This PEI Printing Plate Kit is suitable for CR-10 series printers. If you encounter any issues, please contact us through Amazon. We will reply to you within 24 hours!
- Compatibility This platform bed is compatible with the following 3d printers: Ender-3 max, CR-10S Pro, CR-10 V2, CR-10 V3, CR-X, CR-X Pro, CR-10S Pro V2.
- See more on Amazon...
Brand: Creality | Manufacturer: Creality
Dimensions: 0.78 x 12.60 x 12.20 inches
Warranty: 12 months warranty
See On Amazon #5
Ender 3 S1 Plus 3D Printer Powder Painted PEI Flexi Steel Magnetic Build Plate 310 * 315mm for Creality CR-10/10S Pro/MP Maker Pro Long LK1/ PRO LK5 PRO/Ender 3 Max
Asin: B0BRN3Z1JK | Model: CR-Power PEI-310X315mm | PartNumber: CR-Power PEI-310X315mm
Two-In-One Type Of Pei Powder Coated Hardended Steel Spring Sheet Nerver Disforming, Magnetic Base With Strong Magnetism.
No More Tape, No More Glue, No More Shovel, And Release Your Printing Anxiety.
Easy To Install, Easy To Remove The Models By Bending Or Popping It Off.
Size: 310Mm X 315Mm.
Features
- Compatible with CR-10/10S Pro/CR-10 Smart/CR-10 Smart Pro/MP Maker Pro Long LK1/ PRO LK5 PRO/Ender 3 Max/Ender 3 S1 Plus
- Size: 310mm x 315mm
- Two-in-one type of PEI powder coated hardended steel spring sheet nerver disforming, Magnetic base with strong magnetism
- Easy to install, easy to remove the models by bending or popping it off
- No more tape, no more glue, no more shovel, and release your printing anxiety
- See more on Amazon...
Brand: Creality | Manufacturer: Creality 3D
See On Amazon #6
CHPOWER for Creality CR10 Bed Plate, 300x300 Build Plate, CR-10S Ultra-Flexible Removable Magnetic Build Surface 3D Printer Heated Bed Cover for CR-10 V3 /Ender 3 Max- 310x310mm
Asin: B07J69T6SK | Model: CR-10 magnetic heated bed | PartNumber: CR-10 magnetic heated bed
300Mm Magnetic Bed: Durability & Easy Clean: Cr-10 Bed Surface Is Capable To Work At 70ºc. Easy Clean With Alcohol..
More Flat For Precision: Super Flatness. Prevent Warping. Fast And Uniform Heating. More Precise On Printing, Especially The Bottom Of The Prints..
Simple Installation: This Cr-10 Plate Comes With Upper Magnetic Build Surface And Lower Magnetic Adhesive Base. Place Lower 3M Adhesive Surface On Top Of Normal Build Plate..
Size: 300X300mm Magnetic Bed. Suitable For All Fdm Printer Models, And All Heated And Non-Heated 3D Printer Beds..
Features
- EASY REMOVAL OF PRINTS: CR-10 upgrade parts, simply prints on the surface, remove the upper magnetic surface from the lower, bend the flexible surface and watch the model fall right into your hands. The first 3D printing surface designed with model removal in mind. This surface is easily removed, and flexible.
- SIZE: 300x300mm magnetic bed. Suitable for all FDM printer models, and all heated and non-heated 3D printer beds.
- 300mm magnetic bed: DURABILITY & EASY CLEAN: CR-10 bed surface is capable to work at 70 C. Easy clean with alcohol.
- SIMPLE INSTALLATION: This CR-10 plate comes with upper magnetic build surface and lower magnetic adhesive base. Place lower 3M adhesive surface on top of normal build plate.
- MORE FLAT FOR PRECISION: Super Flatness. Prevent warping. Fast and uniform heating. More precise on printing, especially the bottom of the prints.
- See more on Amazon...
Brand: CHPOWER | Manufacturer: CHPOWER
See On Amazon #7
Geeetech PEI Sheet 310x310mm, Double Textured Surface Magnetic Build Plate, Flexible Removable Spring Steel with Adhesive for Creality CR-10 CR-10S/10 S3, Sidewinder X1/X2 S8 Pro S8 Plus KP5L SP-5
Asin: B09MKKW9TX
【Simple Installation】This 3D Printer Bed Consists Of Two Parts,One Sheet Of Magnetic Base And One Sheet Of Pei-Coated Frosted Spring Steel Platform. Just Need To Place The Bottom 3M Adhesive Surface To Your Heated Bed, Pei Bed Can Be Magnetically Bonded..
【Wide Application】The Size Of Pei Sheet Is 310*310Mm *4.06Mm(12.2*12.2Inch), It's Suitable For Geeetech A30, A30m, A30t, A30 Pro And Creality Cr-10, Cr-10S, Sidewinder X1/X2 S8 Pro S8 Plus Kp5l Sp-5 X40v2 Tevo Tornado, Anet A8, E12, Mp Maker Pro And Other Same Sized 3D Printers, Compatible With Pla, Petg, Peek, Abs 3D Printer Filaments..
【Easy To Adhere And Remove】This Cr-10 Pei Build Plate Surface Has Excellent Adhesion, Easy To Stick And Remove, No Glue And Shovel Required, And When The Build Surface Cools To Room Temperature, Prints Can Be Removed By Bending The Steel Plate Slightly.
【High-Quality Spring Steel】 Hardened Steel Spring Plate Has No Curling Edges, It Has Extremely High Magnetic Properties, Can Be Well Adhered To The Magnetic Base, Cr 10 Pei Sheet Can Withstand Numerous Thermal Cycles Of The Print Bed Without Deformation.
Features
- Textured Surface The golden yellow matte surface with PEI powder coating has strong heat resistance, flame resistance, abrasion resistance and high print stability. The max temp for printing on the bed can reach 130 C, and the best adhesion is around 60 C
- High-quality Spring Steel Hardened steel spring plate has no curling edges, it has extremely high magnetic properties, can be well adhered to the magnetic base, CR 10 PEI sheet can withstand numerous thermal cycles of the print bed without deformation
- Simple Installation This 3d printer bed consists of two parts,one sheet of magnetic base and one sheet of PEI-coated frosted spring steel platform. Just need to place the bottom 3M adhesive surface to your heated bed, PEI bed can be magnetically bonded.
- Easy to Adhere and Remove This cr-10 pei build plate surface has excellent adhesion, easy to stick and remove, no glue and shovel required, and when the build surface cools to room temperature, prints can be removed by bending the steel plate slightly
- Wide Application The size of PEI sheet is 310*310mm *4.06mm(12.2*12.2inch), It's suitable for Geeetech A30, A30M, A30T, A30 PRO and Creality CR-10, CR-10S, Sidewinder X1/X2 S8 Pro S8 Plus KP5L SP-5 X40V2 Tevo Tornado, Anet A8, E12, MP Maker Pro and other same sized 3D Printers, Compatible with PLA, PETG, PEEK, ABS 3d printer filaments.
- See more on Amazon...
Brand: GIANTARM | Manufacturer: GIANTARM
See On Amazon #8
Official Creality Ender 3 Max Neo Build Plate Upgrade PEI Sheet 320x310mm Textured PEI Sheet for Ender-3 Max/Ender-3 Max Neo/CR-X Pro/CR-10 V2/V3/CR-10S Pro
Asin: B0CTMD25SS
High Quality Spring Steel - Crafted From High-Precision Spring Steel, Our Build Plate Ensures Exceptional Flatness, Guaranteeing Uniform Layer Adhesion During Printing. Its Elasticity Eases Prints Removal By Gently Bending. The Durable Plate Withstands Heating, Cooling Cycles, And Bending For Extended Use. Excellent Thermal Conductivity Ensures Even Heat Distribution, Preventing Object Contraction Or Deformation, Significantly Enhancing 3D Printing Quality, Convenience, And Durability..
In Order To Save Your Costs And Minimize Unnecessary Waste, This Product Only Includes A Pei Sheet Without Magnetic Sheet. Therefore, It Is Suitable For Users Whose Original Magnetic Sticker Is Still Functional. If The Original Magnetic Sticker Is Damaged, Please Consider Purchasing The Build Plate Kit That Includes Magnetic Sheet..
Efficient Magnetic Design - Magnetic Sheet Base Allows The Build Plate To Be Quickly And Conveniently Replaced Without The Need For Additional Tools Or Fixing Methods. The Inclusion Of Dual Handles And Positioning Holes Ensures That The Build Sheet Can Be Accurately Aligned In A Single Step During Installation, Simplifying The Process And Providing Users With A More Efficient Printing Experience..
The Pei Coating Is Characterized By Its Wear Resistance And High-Temperature Durability. It Is Not Easily Scratched And Is Widely Applicable To Various Printing Materials. It Provides Reliable Adhesion To The Prints Under Both High And Low Temperatures, Ensuring Stable 3D Printing Without Warping And Significantly Improving The Success Rate Of Prints..
Features
- Official Original Build Plate - Offical Creality CR-10S Pro build plate, with dimensions of 320x310mm. Additionally, it is compatible with other FDM printers of the same print size, such as CR-10S PRO, CR-10 V2, CR-10 V3, CR-X, CR-X Pro, CR-10S PRO V2, Ender-3 Max, Ender-3 Max Neo, etc. Please review the detailed information in the images to determine compatibility with your printer.
- The PEI coating is characterized by its wear resistance and high-temperature durability. It is not easily scratched and is widely applicable to various printing materials. It provides reliable adhesion to the prints under both high and low temperatures, ensuring stable 3D printing without warping and significantly improving the success rate of prints.
- High Quality Spring Steel - Crafted from high-precision spring steel, our build plate ensures exceptional flatness, guaranteeing uniform layer adhesion during printing. Its elasticity eases prints removal by gently bending. The durable plate withstands heating, cooling cycles, and bending for extended use. Excellent thermal conductivity ensures even heat distribution, preventing object contraction or deformation, significantly enhancing 3D printing quality, convenience, and durability.
- Efficient Magnetic Design - Magnetic sheet base allows the build plate to be quickly and conveniently replaced without the need for additional tools or fixing methods. The inclusion of dual handles and positioning holes ensures that the build sheet can be accurately aligned in a single step during installation, simplifying the process and providing users with a more efficient printing experience.
- In order to save your costs and minimize unnecessary waste, this product only includes a PEI sheet without magnetic sheet. Therefore, it is suitable for users whose original magnetic sticker is still functional. If the original magnetic sticker is damaged, please consider purchasing the build plate kit that includes magnetic sheet.
- See more on Amazon...
Brand: Creality | Manufacturer: Creality
See On Amazon #9
Gizmo Dorks PEI Sheet 3D Printer Build Surface 300mm x 300mm (11.8" x 11.8") with Laminated 3M 468MP Adhesive, Made in The USA
Asin: B07FVL1SYF | Model: GD-PEI3M-300MM | PartNumber: GD-PEI3M-300MM | Ean: 0887503182125 | UPC: 887503182125
Build Surface - Pei Is The Perfect No Prep Build Surface Which Is Endlessly Reusable For Multiple Prints; Clean With Isopropypl Alcohol Between Prints (Or With Acetone On A Cold Bed).
Dimensions: 300Mm X 300Mm / Pei Thickness: 0.56Mm (0.022 Inches) / Laminated 3M 468Mp Adhesive Thickness: 0.13Mm (0.005 Inches).
Abs And Pla Filaments (Along With Many Other Materials) Print Directly On To Pei Surface Without The Need For Additional Adhesives, Tapes, Or Slurry.
Bubble Free Application - The 3M 468Mp Adhesive Is Already Preapplied To The Pei; Simply Peel Back The Tape Liner For Quick Adhesion To The Bed.
Features
- Made in the USA - Ultem 1000 PEI sheet installs quickly via the laminated adhesive on top of existing flat build platforms (e.g. borosilicate glass)
- Bubble free application - The 3M 468MP adhesive is already preapplied to the PEI; simply peel back the tape liner for quick adhesion to the bed
- Build Surface - PEI is the perfect no prep build surface which is endlessly reusable for multiple prints; clean with isopropypl alcohol between prints (or with acetone on a COLD bed)
- ABS and PLA filaments (along with many other materials) print directly on to PEI surface without the need for additional adhesives, tapes, or slurry
- Dimensions: 300mm x 300mm / PEI thickness: 0.56mm (0.022 inches) / Laminated 3M 468MP adhesive thickness: 0.13mm (0.005 inches)
- See more on Amazon...
Brand: Gizmo Dorks | Manufacturer: Gizmo Dorks
Dimensions: 0.03 x 11.80 x 11.80 inches
See On Amazon #10
Gizmo Dorks PEI Sheet 3D Printer Build Surface 310mm x 320mm Compatible for CR-10S Pro or Pro V2, Made in The USA
Asin: B0866BV7KJ | Model: GD-PEI3M-310-320 | PartNumber: GD-PEI3M-310-320 | Ean: 0887503183269 | UPC: 887503183269
Build Surface - Pei Is The Perfect No Prep Build Surface Which Is Endlessly Reusable For Multiple Prints; Clean With Isopropypl Alcohol Between Prints (Or With Acetone On A Cold Bed).
Pei Dimensions: 310Mm X 320Mm X 0.56Mm / Laminated 3M 468Mp Adhesive Thickness: 0.13Mm (0.005 Inches) / Fits The Creality Cr-10S Pro V2, Ender 3 Max, And Other Printers Perfectly.
Abs And Pla Filaments (Along With Many Other Materials) Print Directly On To Pei Surface Without The Need For Additional Adhesives, Tapes, Or Slurry.
Bubble Free Application - The 3M 468Mp Adhesive Is Already Preapplied To The Pei; Simply Peel Back The Tape Liner For Quick Adhesion To The Bed.
Features
- Made in the USA - Ultem 1000 PEI sheet installs quickly via the laminated adhesive on top of existing flat build platforms (e.g. borosilicate glass)
- Bubble free application - The 3M 468MP adhesive is already preapplied to the PEI; simply peel back the tape liner for quick adhesion to the bed
- Build Surface - PEI is the perfect no prep build surface which is endlessly reusable for multiple prints; clean with isopropypl alcohol between prints (or with acetone on a COLD bed)
- ABS and PLA filaments (along with many other materials) print directly on to PEI surface without the need for additional adhesives, tapes, or slurry
- PEI Dimensions: 310mm x 320mm x 0.56mm / Laminated 3M 468MP adhesive thickness: 0.13mm (0.005 inches) / Fits the Creality CR-10S Pro v2, Ender 3 Max, and other printers perfectly
- See more on Amazon...
Brand: Gizmo Dorks | Manufacturer: Gizmo Dorks
Dimensions: 0.03 x 12.60 x 12.20 inches | Weight: 0.23 Pounds
See On Amazon #11
PEI Sheet(Double-Sided)310mm*320mm and Magnetic Sticker with Adhesive for Creality CR-10S Pro,CR-X,CR-10 Pro V2,Ender 3 Max,CR-10 V3 3D Printer
Asin: B0CB8QGQ2R | Model: PEI 320 | PartNumber: PEI 320 | Ean: 0795847035505 | UPC: 795847035505
【More Affordable And Practical】 Our Pei Sheet Is Made With 75% Thicker Pei And 25% Thicker Spring Steel Than Our Leading Competitors, Providing A More Durable Plate That Can Handle The Tough Conditions Of 24/7 Printing. Our Magnet Can Also Sustain Higher Temperatures Of Up To 120°C, Making It Wear-Resistant And Scratch-Resistant. Additionally, It's Easy To Clean With A Protective Film On The Surface Of The Composite Coating That Is Anti-Scratch And Dustproof..
【Easy Removal】When Used In A 3D Printing Application,Pei Is Excellent Because It Can Withstand The Numerous Heat Cycles That A 3D Print Bed Goes Through From Print To Print.Our Surface Is Easily Removed And Flexible,Allowing Prints To Come Off The Surface Easily When The Temperature Of The Heated Bed Reaches Room Temperature.After The Model Printing Is Complete,Simply Remove The Upper Magnetic Surface From The Lower, Bend The Flexible Surface, And Watch The Model Fall Right Into Your Hands..
【Simple Installation】 Our Pei Sheet Is Easy To Install. Simply Stick The Magnetic Bottom Sheet Onto Your Chosen Build Plate, And Then Place The Steel Platform With Pei Surface On Top. Easily Replaces An Ender 3 Max Bed, Cr 10S Pro Bed, Or Any Other Type Of Platform.Our Pei Sheet Is Flexible, Removable, And Sticks To Magnetics Very Well. It's Made With High Strength And Heat Resistance Materials, Including Spring Stainless Steel And Pei Powder Sprayed On The Surface..
【Excellent Adhesion】 Our Pei Sheet Provides Excellent Adhesion For Your Prints, Allowing Them To Stick Securely To The Printing Surface While Still Being Easy To Remove. Our Pei Sheet Is Compatible With Various Bed Types, Including The Cr-10S Pro Bed, Cr-X Bed,Cr-10 Pro V2 Bed, Ender 3 Max Bed, Cr-10 V3 Bed, And Any Similarly Sized 3D Printer Bed. You Can Print Directly Onto Each Side Of The Double-Sided Sheet Without The Need For Glue Or Any Other Adhesives..
Features
- Wide Application Our PEI sheet is 310mm x 320mm, For CR-10S Pro,CR-X,CR-10 Pro V2,Ender 3 Max,CR-10 V3 and similarly sized FDM 3D printers. Our PEI sheet is also compatible with various build plate types, Compatible with PLA, PETG, PEEK, ABS, and any other filaments.
- Excellent Adhesion Our PEI sheet provides excellent adhesion for your prints, allowing them to stick securely to the printing surface while still being easy to remove. Our PEI sheet is compatible with various bed types, including the CR-10S Pro bed, CR-X bed,CR-10 Pro V2 bed, Ender 3 Max bed, CR-10 V3 bed, and any similarly sized 3D printer bed. you can print directly onto each side of the double-sided sheet without the need for glue or any other adhesives.
- More Affordable and Practical Our PEI sheet is made with 75% thicker PEI and 25% thicker spring steel than our leading competitors, providing a more durable plate that can handle the tough conditions of 24/7 printing. Our magnet can also sustain higher temperatures of up to 120 C, making it wear-resistant and scratch-resistant. Additionally, it's easy to clean with a protective film on the surface of the composite coating that is anti-scratch and dustproof.
- Simple Installation Our PEI sheet is easy to install. Simply stick the magnetic bottom sheet onto your chosen build plate, and then place the steel platform with PEI surface on top. Easily replaces an Ender 3 Max bed, CR 10S Pro bed, or any other type of platform.Our PEI sheet is flexible, removable, and sticks to magnetics very well. It's made with high strength and heat resistance materials, including spring stainless steel and PEI powder sprayed on the surface.
- Easy Removal When used in a 3D printing application,PEI is excellent because it can withstand the numerous heat cycles that a 3D print bed goes through from print to print.Our surface is easily removed and flexible,allowing prints to come off the surface easily when the temperature of the heated bed reaches room temperature.After the model printing is complete,simply remove the upper magnetic surface from the lower, bend the flexible surface, and watch the model fall right into your hands.
- See more on Amazon...
First Available: 08/24/2023
Brand: UNIDO | Manufacturer: YOOPAI
Warranty: 180
See On Amazon #12
FYSETC Ender-7 Build Plate Upgrades - 280x280mm PET PEI Spring Steel Sheet - Smooth Textured Print Bed: Double-Sided Flex Hotbed Cover with Magentic Sticker for Filament PLA PETG 3D Printer Part
Asin: B0CXPKWTV6
3. Easy To Use: *Do Not Sand The Pet Surface!* Peel Off The Backing Paper Of Soft Sticker, Stick Onto The Aluminum Plate, Then Align The Pei Build Plate. After Installing, Level The Print Bed With Auto Bed Leveling Sensor To Adjust The Height Of Z Axis. An Appropriate Z Is Very Important For The 3D Printing Project. Note: Turn Off The Cooling Fan And Slow Down The Speed To 10-25Mm/S To Get A Better First Layer Adhesion. Note The Distance Between The Nozzle And Print Surface About 0.05-0.2Mm..
5. Flexible And Easy To Remove: Made Of High Quality Steel Plate, Much Of Flexibility. Prints Can Be Easily Removed By Hand Once The Build Surface Has Cooled, Or You Can Bend The Build Plate After The Pei Plate Cooled And Remove The Prints. The Print Mat Won’T Be Out Of Shape, Multiple Bending Without Deformation. Enjoy Your 3D Printing Journey!.
4. Wide Filament Compatibility: Compatible With Most 3D Printing Material, Such As Pla, Petg, Tpu, High Temp Abs(Recommend On The Matte Bedplate With A 3D Printer Dust Cover). The Pet Print Bed Surface Is Resistant To High Temperature 90℃ And The Pei Coating Is 260℃. One Heating Bed Can Obtain Two Different Experience Just By Flipping It Over. Excellent Layer Adhesion, Easy Model Removal, Simple And Non-Destructive Modification. No More Tape, No More Shovel, Release Your Printing Anxiety..
2. Compatible Models: The Sheet Size Is 280X280mm/11.02X11.02Inch, Compatible With Metal Struture Core-Xy Crealty Ender 7 Or Qid X-Plus 3 Desktop 3D Printers. A Perfect Bedplate For The Original Lattice Glass Bed, No Need The Bed Clips. The Bed Sheet Size Is Enough 280Mm, Please Remeasure Your Heated Plate Before Ordering To Avoid Wrong Buy. Not Rely On The Machine's Printing Size Or Build Volume..
Features
- 1. Upgraded Double Sided Printing: Double-sided PET - PEI spring steel plate. One side is a smooth PET coating, Great adhesion, prints just pop off the plate. Will leave a texture on your print that looks like carbon fiber, but is still completely smooth to the touch. The other side is PEI powder-coated surface, presents a distinctive frosted touch, provides higher adhesion for the model and pressure without warping. With a Magletic Sticker Base. A complete kit for your 3d printing project.
- 2. Compatible Models: The sheet size is 280x280mm/11.02x11.02inch, compatible with Metal Struture Core-XY Crealty Ender 7 or QID X-Plus 3 desktop 3d printers. A perfect bedplate for the original lattice glass bed, no need the bed clips. The bed sheet size is enough 280mm, please remeasure your heated plate before ordering to avoid wrong buy. Not rely on the machine's printing size or build volume.
- 3. Easy to Use: *Do Not Sand the PET Surface!* Peel off the backing paper of soft sticker, stick onto the aluminum plate, then align the PEI build plate. After installing, Level the print bed with auto bed leveling sensor to adjust the height of Z Axis. An Appropriate Z is Very important for the 3d printing project. Note: Turn OFF the cooling fan and Slow Down the Speed to 10-25mm/s to get a better first layer adhesion. Note the distance between the nozzle and print surface about 0.05-0.2mm.
- 4. Wide Filament Compatibility: Compatible with most 3d printing material, such as PLA, PETG, TPU, high temp ABS(recommend on the Matte bedplate with a 3d printer dust cover). The PET print bed surface is resistant to high temperature 90 and the PEI coating is 260 . One heating bed can obtain two different experience just by flipping it over. Excellent layer adhesion, easy model removal, simple and non-destructive modification. No more tape, no more shovel, release your printing anxiety.
- 5. Flexible and Easy to Remove: Made of high quality steel plate, much of flexibility. Prints can be easily removed by hand once the build surface has cooled, or you can bend the build plate after the PEI plate cooled and remove the prints. The print mat won t be out of shape, multiple bending without deformation. Enjoy your 3d printing journey!
- See more on Amazon...
Brand: FYSETC | Manufacturer: fuyuansheng
Dimensions: 0.03 x 11.02 x 11.02 inches | Weight: 1.30 pounds
See On Amazon #13
FYSETC 3D Printer Vorn 2.4 350mm Build JanusBPS PEI Sheet 355x355mm/13.9x13.9inch Flexible Spring Steel Sticker Build PlateTextured - Smooth Double Sided Removable Heated Bed Cover Kit for Vorn v2.4
Asin: B09GYB7B2C
Easy To Use, Simply Stick The Sticker Bottom Sheet Onto Your Heated Bed, Then Place The Steel Platform On The Top.Both Sides Can Be Used To Print, Convenient. The Pei Sheet Is Pre-Sticked By Machine, No Need Worry About Bubbles. Please Peel Off The Profective Film On It Before Using..
The Flexible Steel Pei Sheet Is Made Of High Quality Spring Steel That Won't Kink Or Warp When You Flex Them Slightly! Easy To Adhere To The Printing Surface, Easy To Remove The Prints. Prints Come Off The Surface Easily When The Temperature Of The Heated Bed Reaches Room Temperature. If The Print Is Still Stuck, Gentle Flexing Of The Plate Will Help Remove It..
Most Filaments, Such As Pla, Petg, Can Print Directly On To The Pei Surface Without The Need For Additional Adhesives, Tapes Or Slurry. Kindly Note Printing Abs Needs A Thermal Insulation Environment..
Flexible, Removable, Can Stick To Sticker Very Well. High Strength And Heat Resistance, Apply To The Same Size Vorn 2.4 Printer--350 V2, Sovl Sv03 (Please Measure Your Build Plate Before Ordering,Not Rely On Bulid Volume)..
Features
- A upgrade Replacement printing platform JanusBPS-Build Plate Sheet 355mm/13.9 inch. This JanusBPS kit is one side with Gold Powder, another with a Smooth PEI, comes with a soft sticker base with strong adhesive.
- Flexible, removable, can stick to sticker very well. High strength and heat resistance, apply to the same size Vorn 2.4 printer--350 V2, Sovl SV03 (Please measure your build plate before ordering,not rely on bulid volume).
- Easy to use, simply stick the sticker bottom sheet onto your heated bed, then place the steel platform on the top.Both sides can be used to print, convenient. The pei sheet is pre-sticked by machine, no need worry about bubbles. Please peel off the profective film on it before using.
- Most filaments, such as pla, petg, can print directly on to the pei surface without the need for additional adhesives, tapes or slurry. Kindly note printing ABS needs a thermal insulation environment.
- The flexible steel PEI sheet is made of high quality spring steel that won't kink or warp when you flex them slightly! Easy to adhere to the printing surface, easy to remove the prints. Prints come off the surface easily when the temperature of the heated bed reaches room temperature. If the print is still stuck, gentle flexing of the plate will help remove it.
- See more on Amazon...
Brand: FYSETC | Manufacturer: Fuyuansheng
See On Amazon #14
Double Sided Textured PEI Sheet, 3D Printer Parts Printing Plate Frosted PEI Surface 310 x 310 mm for CR-10 CR-10S Anet A8+, E12,3D Printers(Without Magnetic Bottom Sheet)
Asin: B09YY4L4K1 | Model: MY001 | PartNumber: MY001 | Ean: 0705548422535 | UPC: 705548422535
【High Temperature Resistance】:Genuine Pei Powder Coating Is Heat Resistant Which Temperature Resistance Can Be Up To 200℃ With No Deformation.
【Easy To Use】Pei Spring Steel Easy To Remove The Plastic Parts By Bending And Popping It Off When Cooling, Easy To Print, Easy To Maintain.
【Textured Surface】:The Textured Side Makes The Bottom Of The Prints Show A Matte Texture And Retain The Frosted Feeling.And Perfect For Pla/Abs/Tpu/Pefg/Nylon..
【Double-Sided】】:Pei Magnetic Flexible Bed Has Double-Sided Pei Coating, Both Sides Can Be Used..
Features
- Upgrade PEI Sheet :310mm x 310mm/12.2x12.2 inch, compatible with CR-10 10S Pro CR-X MP Maker Pro, Long LK1/ PRO LK5 PRO/Artilery X1ease measure your bed, not rely on build volume/printing size.
- Double-sided :PEI magnetic Flexible bed has double-sided PEI coating, both sides can be used.
- High Temperature Resistance :Genuine PEI powder coating is heat resistant which temperature resistance can be up to 200 with no deformation
- Textured Surface :The textured side makes the bottom of the prints show a matte texture and retain the frosted feeling.And perfect for PLA/ABS/TPU/PEFG/Nylon.
- Easy to use PEI Spring steel Easy to remove the plastic parts by bending and popping it off when cooling, easy to print, easy to maintain
- See more on Amazon...
Brand: MYOSOTIS | Manufacturer: china
See On Amazon #15
HICTOP Textured PEI Bed 310 * 320mm Build Plate PEI Sheet and Magnetic Build Plate Adhesive Ender 3 max PEI for CR-10 V2,CR-10 V3,CR-10S pro,CR-X, CR-10 pro V2,Ender 3 max,Ender 3 max Neo 3D Printers
Asin: B09KLFYCQ6 | Model: PEI | PartNumber: PEI
3 Excellent Adhesion Can Be Achieved When The Temperature Of The Heated Bed Is About 60℃, You Can Print Directly On The Hictop Pei Sheet Without Using Any Glue Or Other Tools To Help The Model To Stick Onto The Sheet. You Do Not Need To Worry About The Prints Curling With A 60℃ Bed Temperature.It Also Can Print Petg Very Well, But The Temperature Of The Hotbed Needs To Be About 80-85℃.
5 The Size Of Hictop Pei Sheet Is 310*320Mm（12.2*12.6Inch）, It Is Applicable With Cr-10 V2,Cr-10 V3,Cr-10S Pro, Cr-X, Cr-10 Pro V2, Ender 3 Max, Ender 3 Max Neo Anycubic Kobra Plus 3D Printers.
4 Prints Come Off The Surface Easily When The Temperature Of The Heated Bed Reaches Room Temperature. If The Print Is Still Stuck, Gentle Flexing Of The Plate Will Help Remove It..
2 The Hictop 310*320Mm Pei Is Very Easy To Use, Simply Stick The Magnetic Bottom Sheet Onto Your Heated Bed, Then Place The Steel Platform With Pei Surface On The Top. The Maximum Temperature For Printing Is 130℃ On The Bed..
Features
- 1 The HICTOP 310*320mm pei bed is combined with 2 parts, a flexible steel platform coated with textured PEI on one side and a magnetic bottom sheet with adhesive on the back. The PEI comes pre applied.
- 2 The HICTOP 310*320mm pei is very easy to use, simply stick the magnetic bottom sheet onto your heated bed, then place the steel platform with PEI surface on the top. The maximum temperature for printing is 130 on the bed.
- 3 Excellent adhesion can be achieved when the temperature of the heated bed is about 60 , you can print directly on the HICTOP PEI sheet without using any glue or other tools to help the model to stick onto the sheet. You do not need to worry about the prints curling with a 60 bed temperature.It also can print PETG very well, but the temperature of the hotbed needs to be about 80-85
- 4 Prints come off the surface easily when the temperature of the heated bed reaches room temperature. If the print is still stuck, gentle flexing of the plate will help remove it.
- 5 The size of HICTOP pei sheet is 310*320mm 12.2*12.6inch , it is applicable with CR-10 V2,CR-10 V3,CR-10S pro, CR-X, CR-10 pro V2, Ender 3 max, Ender 3 max Neo Anycubic Kobra Plus 3D printers
- See more on Amazon...
Brand: HICTOP | Manufacturer: HICTOP
See On Amazon #16
4pcs 11.8 11.8inch (300 300mm) Heated Bed Sticker Printing Build Sheets Plate Tape Platform Sticker 3D Printing Build Surface Sheets for Creality CR-10S /CR-10 PLA PETG Filament FDM 3D Printer
Asin: B0BTBP7XZG | Model: 300*300mm | PartNumber: 300*300mm | Ean: 0701715520691 | UPC: 701715520691
Widely Used In All Fdm Printer Models, And All Heated And Non-Heated 3D Printer Beds.
Build Surface Comes With Upper Magnetic Build Surface And Lower Magnetic Adhesive Base, Easy To Use.
More Flat For Precision: Super Flatness. Fast And Uniform Heating. More Precise On Printing, Especially The Bottom Of The Prints.
The Magnetic Plate Are Very Easy To Use, Simply Stick The Magnetic Bottom Sheet Onto Your Heated Bed, Then Place The Steel Platform With Pei Surface On The Top. The Maximum Temperature For Printing Is 120℃ On The Bed..
Features
- The size of flexible PEI build plate 300*300mm 11.8*11.8inch
- The magnetic plate are very easy to use, simply stick the magnetic bottom sheet onto your heated bed, then place the steel platform with PEI surface on the top. The maximum temperature for printing is 120 on the bed.
- Widely used in all FDM printer models, and all heated and non-heated 3D printer beds
- More Flat for Precision: Super Flatness. Fast and uniform heating. More precise on printing, especially the bottom of the prints
- Build surface comes with upper magnetic build surface and lower magnetic adhesive base, easy to use
- See more on Amazon...
Brand: DWEII | Manufacturer: Dweii
See On Amazon #17
FYSETC 3D Platform Prusa i3 MK3S+ MK4 PEY Build Plate: Upgrade Smooth PEY - Textured PEI Spring Steel Sheet Flexible Hot Bed Cover Removable Print Bed for MK2 MK52 MK3 MK3S XL 3D Printer Bed 254x241mm
Asin: B0CJXLG5G1
【Wide 3D Printing Material Compatibility】Support Various 3D Printer Filaments. After Testing, We Recommend The Pey Layer To Print Pla/ Tpu/ Petg (Temp Suggestion: 50°C-70°C, ≤90°C). The Textured Pei Plate Print Pla/ Pla-Cf/ Petg/ Pc/ Abs/ Tpu/ Nylon Etc. Printing Model Is Easy To Adhere On Pei Bed, Has A Great Adhesion, And Easy To Be Removed , Just Flex Slightly To Pop Your Prints Right Off. In Some Cases, Remove The Model Directly Without Taking The Printing Bed From Prusa Mk3 3D Printer..
【More Support】All Products Are Inspected Before Shipment. If You Have Any Questions About Product Quality Or Suggestions, Please Feel Free To Contact Us Via Your Order Id. We Are Very Grateful For Your Love And Care For The Product. 3D Printer Print Bed Is Our Main Product, This Kind Of Multicolor Pei - Pey Steel Plate Is Not Only Available In 254X241mm But Also In 196X190mm - Prusa Mini/ 235X235mm - Ender 3 V2, Ender 5, Neptune3, Neptune4/ 257X257mm - Bambulab X1c P1p P1s..
【Proven Solution】Made Of High Quality Spring Steel Plate. Flexible, Removable, High Strength And Heat Resistance, Dual-Side Design, Thicker And More Durable. Easy To Use, Put The Printing Plate Onto The Lab Printer Hot Bed, Then The Print Bed Levelling Will Automatically Go On While Machine Powered On. (Note:The Smooth Surface Has A Factory Protective Film That Needs To Be Removed.).
【A New Shiny Prusa Bed Plate】The Smooth Pey Side Is The Latest Printing Surface In Prusa I3 Mk3 Parts, Size 254X241mm/10X9.5Inch. Flaring Stars And Dots Fill The Entire Spring Plate, Which Makes Itself Beautiful As A Picture. Another Magical Thing, It Presents Different Patterns Under Different Intensities Of Light And Angles. This Is Its Distinctive Feature From Other 3D Printer Bed Mats, Such As Peo Plate, Pei Sheet Or Pet Plate Sheet Etc..
Features
- Upgrade Prusa Build Plate A new Double Sided heated bed sheet: Smooth PEY + Textured PEI. One side is a textured PEI bed which presents the frosted surface with a distinctive frosted touch. Another side is coated with a smooth PEY sheet which has a Starry & Fine Sequins pattern that shines brightly. The most important thing, the Stars and Dots pattern will be left on the printing model, which brings endless fun to your 3d printing. How Beautiful and Magical!
- A New Shiny Prusa Bed Plate The smooth PEY side is the latest printing surface in Prusa i3 mk3 parts, Size 254X241mm/10x9.5inch. Flaring stars and dots fill the entire spring plate, which makes itself beautiful as a picture. Another magical thing, it presents different patterns under different intensities of light and angles. This is its distinctive feature from other 3d printer bed mats, such as peo plate, pei sheet or PET plate sheet etc.
- Wide 3D Printing Material Compatibility Support various 3d printer filaments. After testing, we recommend the PEY layer to print PLA/ TPU/ PETG (Temp Suggestion: 50 C-70 C, 90 C). The textured PEI plate print PLA/ PLA-CF/ PETG/ PC/ ABS/ TPU/ Nylon etc. Printing model is easy to adhere on PEI bed, has a great adhesion, and easy to be removed , just flex slightly to pop your prints right off. In some cases, remove the model directly without taking the printing bed from prusa mk3 3d printer.
- Proven Solution Made of high quality spring steel plate. Flexible, removable, high strength and heat resistance, dual-side design, thicker and more durable. Easy to use, put the printing plate onto the lab printer hot bed, then the print bed levelling will automatically go on while machine powered on. (Note:The smooth surface has a factory protective film that needs to be removed.)
- More Support All products are inspected before shipment. If you have any questions about product quality or suggestions, please feel free to contact us via your order ID. We are very grateful for your love and care for the product. 3D printer print bed is our main product, this kind of multicolor PEI - PEY steel plate is not only available in 254x241mm but also in 196x190mm - Prusa Mini/ 235x235mm - Ender 3 V2, Ender 5, Neptune3, Neptune4/ 257x257mm - Bambulab X1C P1P P1S.
- See more on Amazon...
Brand: FYSETC | Manufacturer: fuyuansheng
Dimensions: 0.03 x 10.00 x 9.49 inches
See On Amazon #18
IdeaFormer-3D Smooth PEO+Textured PEI Sheet 310x320mm, PEO+PEI Spring Steel Plate with Magnetic Build Plate for Ender 3 Max/Ender 3 Max Neo/CR-10 V2/CR-10 V3/CR-10S Pro/CR-X/CR-10 Pro V2/Sovol SV04
Asin: B0CJ26SB5N
【High Temperature Resistance】The Peo Spring Steel Plate Is Resistant To High Temperatures Of 120°C And The Pei Build Plate Is 260°C. (If Printing High-Temperature Filaments Such As Abs, It Is Recommended To Seal The Box For Printing Or Use Glue On The Heat Bed To Assist With Adhesion.).
【Compatible 3D Printers】Our Double-Sided Textured Peo+Pei Build Plate Fit 3D Printers With A Platform Size Of 310X320mm, Such As For Ender 3 Max, Ender 3 Max Neo, Cr-10 V2, Cr-10 V3, Cr-10S Pro, Cr-X, Cr-10 Pro V2, Sovol Sv04..
【Easy To Use And Remove】No More Tape, Glue, Shovel And Release Your Pressure Anxiety. Prints Can Be Easily Removed By Hand Once The Build Surface Has Cooled..
【Compatible Filaments】Peo Spring Steel Plate Only Prints Pla/Petg/Tpu; Pei Build Plate Print Most Filaments Such As Pla / Abs / Petg / Tpu / Nylon..
Features
- Diamond Textured Build Plate PEI + PEO double-sided printing plate, one side is a smooth PEO film which can print beautiful diamond texture appears on the bottom. The other side is PEI frosted surface, the frosted sheet surface presents a distinctive frosted touch, provides higher adhesion for the model and pressure without warping.
- Compatible Filaments PEO spring steel plate only prints PLA/PETG/TPU; PEI build plate print most filaments such as PLA / ABS / PETG / TPU / nylon.
- High Temperature Resistance The PEO spring steel plate is resistant to high temperatures of 120 C and the PEI build plate is 260 C. (If printing high-temperature filaments such as ABS, it is recommended to seal the box for printing or use glue on the heat bed to assist with adhesion.)
- Easy to Use and Remove No more tape, glue, shovel and release your pressure anxiety. Prints can be easily removed by hand once the build surface has cooled.
- Compatible 3D Printers Our double-sided textured PEO+PEI build plate fit 3D printers with a platform size of 310x320mm, such as for Ender 3 Max, Ender 3 Max Neo, CR-10 V2, CR-10 V3, CR-10S Pro, CR-X, CR-10 Pro V2, Sovol SV04.
- See more on Amazon...
Brand: IdeaFormer-3D | Manufacturer: Bell Tech
See On Amazon #19
Comgrow PEI Magnetic Flexible Heated Bed 310x320mm Spring Steel Plate for Creality CR-10 V3/CR-10 V2/Ender 3 Max/Ender 3 Max Neo/CR-10S Pro V2/CR-10S/CR-X/SV04
Asin: B09F6NRXMN
No More Tape, No More Glue, No More Shovel, And Release Your Printing Anxiety..
When Used In A 3D Printing Application, Pei Is Excellent Because It Can Withstand The Numerous Heat Cycles That A 3D Print Bed Goes Through From Print To Print..
Easy To Adhere To The Printing Surface, Easy To Remove The Prints, Flex Slightly To Pop Your Print Right Off..
Compatible With Pla、Petg、Peek、Abs And Any Other Filaments..
Features
- Flexible, removable, can stick to magnetics very well. High strength and heat resistance. (Note: Please remove the transparent protective film on the surface before use).
- Compatible with PLA PETG PEEK ABS and any other filaments.
- No more tape, no more glue, no more shovel, and release your printing anxiety.
- Easy to adhere to the printing surface, easy to remove the prints, flex slightly to pop your print right off.
- When used in a 3D printing application, PEI is excellent because it can withstand the numerous heat cycles that a 3D print bed goes through from print to print.
- See more on Amazon...
Brand: Comgrow | Manufacturer: Creality 3D
See On Amazon #20
FYSETC 3D Printing Build Surface Double Sided Textured Pei Spring Powder Coated Steel Sheet Flexiable Build Plate 300 x 300mm for 3D Printer TAZ 6
Asin: B07V9DY7SM
Two-In-One Type Of Pei Powder Coated Hardended Steel Spring Sheet, Not Easy To Get Desformed. It Behaves As Most Pei Sheets Would And Works Great With Pla, Tpu, Petg, Abs, As Well As Many Other Filaments. If You Need More Adhesion For Tough-To-Stick Filaments Like Nylon, Feel Free To Use Glue Sticks, They Will Wash Off With Water After Use..
To Clean, Use Some Isopropyl Alcohl After Each Use To Keep Contaminants Away. If You Ever Need To Restore Adhesion, Use Very Fine Sandpaper 600 Or Higher And Pass Lightly, Then Clean With Alcohol. For Pla And Petg We Recommend 70° C Bed Temperature..
Easy To Install, Take Off The Back Paper On The Magletic Base, Stick It To The Heated Bed, Then Align The Steel Plate On It. The Model Can Be Easily Removed By Bending The Plate When The Bed Temp Cools Down. It Is Possible To Add Inductive Z Probes And Add Abl Printers For Certain Objects That Need To Be Upgraded..
Size: 300Mm X 300Mm/11.8*11.8 Inch. It's A Stainless Steel Plate With Double-Sides Special Coating(Pei), Which Makes The Bottom Of The Model Show A Textured Mattle Finish..
Features
- Upgrade Spring Steel Sheet: Compatible with 300mm x 300mm hot bed/build plate, TAZ Workhorse, TAZ Pro, TAZ 6, TAZ 5, TAZ 4, TAZ 3, may fit A8 plus, et5 and et5 pro. !!!Please measure your bed, not rely on build volume/printing size which is about 5-10mm smaller than the heatbed.
- Size: 300mm x 300mm/11.8*11.8 inch. It's a stainless steel plate with double-sides special coating(PEI), which makes the bottom of the model show a textured mattle finish.
- Two-in-one type of PEI powder coated hardended steel spring sheet, not easy to get desformed. It behaves as most PEI sheets would and works great with PLA, TPU, PETG, ABS, as well as many other filaments. If you need more adhesion for tough-to-stick filaments like Nylon, feel free to use glue sticks, they will wash off with water after use.
- Easy to install, take off the back paper on the magletic base, stick it to the heated bed, then align the steel plate on it. The model can be easily removed by bending the plate when the bed temp cools down. It is possible to add inductive Z probes and add ABL printers for certain objects that need to be upgraded.
- To clean, use some isopropyl alcohl after each use to keep contaminants away. If you ever need to restore adhesion, use very fine sandpaper 600 or higher and pass lightly, then clean with alcohol. For PLA and PETG we recommend 70 C bed temperature.
- See more on Amazon...
Brand: FYSETC | Manufacturer: Fuyuansheng
See On Amazon
Looking For Something Else?
Search