Peachtree Woodworking Supply 2 inch Diameter Bowl Sander with Dual Bearing Head and 2 inch Foam Hook and Loop Sander with 1/4 inch Mandrel and 9 inch Long Hardwood Handle
Asin: B09BDF46N2 | Model: 26 | PartNumber: 26 | Ean: 0817918022822, 0817918021696 | UPC: 817918022822, 817918021696
As an Amazon Associate we earn a fee from qualifying purchases when you follow a link to Amazon from this page. We rank the products, but the links to Amazon are promotional.It’S All About The Pressure, Or More Like, Its All About The Light Pressure And Consistent Technique. When Sanding With The 2 Inch Bowl Sander, Applying Too Much Pressure Will Likely Produce Some Unsightly Results. By Applying Light Pressure And Consistently Moving The Sander, You Will Achieve The Results You Are Looking For And In A Fraction Of The Time It Typically Takes When Hand Sanding Your Project..
We Have Included The Most Common Diameter Sanding Head With The Bowl Sander. This Sander Head Is Made From A Foam Material That Gives Just Enough To Provide You With Wonderful Looking Results Each Time You Sand Your Projects. This 2” Head Size Works Well On Most Bowl Turning Projects Since It Can Work With Larger Or Smaller Work Pieces. Also Included 10 Ea. 80 Grit, 10 Ea. 120 Grit, 10 Ea. 150 Grit And 10 Ea. 220 Grit Hook And Loop Sanding Discs..
The Head Assembly Is Also Capable Of Accepting Other Size Sanders As Long As The Mandrel/Shank Size Is 1/4 Inch In Diameter. Please Be Aware However That Some Manufacturers Say 1/4 Inch In Diameter When In Actuality The Diameter Is Either Smaller Or Slightly Larger. 3 Brass Bushings Of Varying Depths Are Included To Make Fitting Sanders With Different Length Mandrels/Shanks Easy..
The Head Assembly Is Completely Adjustable So It Can Be Set To Any Angle That You Need Depending On The Size And Curve Of Your Project. Unlike Most Other Bowl Sander Head Assembly’S, Our Bowl Sander Has Two Steel Bearings To Provide You With Super Smooth Mandrel Rotation While Sanding On Your Lathe. This Also Helps To Reduce The Chance Of Marking Your Wood Since The Sander Will Be Rotating Without Hanging Up Or Catching Like So Many Other Brands Do..
Features
- When you need to finish sand the inside of your wood turned bowl it can be a challenge to keep the wood from showing scuff marks. Using a piece of hand held sandpaper can also be somewhat dangerous. Our bowl sander essentially fixes this issue by having a dual bearing, smooth rotating head that spins with the rotation of the bowl while the bowl is rotating on the lathe. The 9 inch long handle also helps keep your hands out of harms way.
- The head assembly is completely adjustable so it can be set to any angle that you need depending on the size and curve of your project. Unlike most other bowl sander head assembly s, our bowl sander has two steel bearings to provide you with super smooth mandrel rotation while sanding on your lathe. This also helps to reduce the chance of marking your wood since the sander will be rotating without hanging up or catching like so many other brands do.
- It s all about the pressure, or more like, its all about the light pressure and consistent technique. When sanding with the 2 inch bowl sander, applying too much pressure will likely produce some unsightly results. By applying light pressure and consistently moving the sander, you will achieve the results you are looking for and in a fraction of the time it typically takes when hand sanding your project.
- The head assembly is also capable of accepting other size sanders as long as the mandrel/shank size is 1/4 inch in diameter. Please be aware however that some manufacturers say 1/4 inch in diameter when in actuality the diameter is either smaller or slightly larger. 3 brass bushings of varying depths are included to make fitting sanders with different length mandrels/shanks easy.
- We have included the most common diameter sanding head with the bowl sander. This sander head is made from a foam material that gives just enough to provide you with wonderful looking results each time you sand your projects. This 2 head size works well on most bowl turning projects since it can work with larger or smaller work pieces. Also included 10 ea. 80 grit, 10 ea. 120 grit, 10 ea. 150 grit and 10 ea. 220 grit hook and loop sanding discs.
- See more on Amazon...
Brand: Peachtree Woodworking Supply | Manufacturer: Peachtree Woodworking Supply Inc.
Dimensions: 3.00 x 12.00 x 2.00 Inches | Weight: 0.85 Pounds
See On Amazon Similar To Peachtree Woodworking Supply 2 inch
#1
Micro-Mesh 2 inch by 2 inch Double Sided Soft Touch Sanding Pads Ideal for Pen and Bottle Stopper Polishing. Perfect for Cycle Sanding Acrylic Materials with CA Glue Finish
Asin: B000H6EC4C | Model: STP-01 | PartNumber: STP-01 | Ean: 5915903721486, 4049933039516, 0810948010517 | UPC: 810948010517
The Pack Includes 1 Each 2 Inch By 2 Inch Soft Touch Pads In The Following Grits: 1500, 1800, 2400, 3200, 3600, 4000, 6000, 8000 & 12000 Plus A Color Coded Grit Guide..
Pads Are Colored Coded With Foam Backing For Easy Grit Identification. Colors May Vary From Images Shown Here. The Colors On The Grit Chart And The Colors Of Micro-Mesh Abrasives May Vary Slightly Due To Color Shifts In The Manufacturing Process..
Ideal For Use With Acrylics, Plastics, Resin Or Impregnated Blanks When Turning. Works Great On Automotive And Marine Body Work. The Pads Can Also Be Used Around The Home For Fine Repair Work..
This Pack Works Extremely Well When Working With Ca Finishes Leaving Your Work Looking Like It Was Done By A Professional! Using The Step Up Process Will Leave Your Project Finish Looking Wonderful ..
Features
- Pen, Bottle Stopper or even small goblet finishing just became a bit more enjoyable with the Micro-Mesh Soft Touch sanding pads! Start with the lowest grit of 1500 all the way up to 12000 grit.
- This pack works extremely well when working with CA finishes leaving your work looking like it was done by a professional! Using the step up process will leave your project finish looking wonderful .
- The pack includes 1 each 2 inch by 2 inch soft touch pads in the following grits: 1500, 1800, 2400, 3200, 3600, 4000, 6000, 8000 & 12000 plus a color coded grit guide.
- Ideal for use with acrylics, plastics, resin or impregnated blanks when turning. Works great on automotive and marine body work. The pads can also be used around the home for fine repair work.
- Pads are colored coded with foam backing for easy grit identification. Colors may vary from images shown here. The colors on the grit chart and the colors of Micro-Mesh abrasives may vary slightly due to color shifts in the manufacturing process.
- See more on Amazon...
Brand: Micro-Mesh | Manufacturer: Micro-Surface
Dimensions: 2.00 x 2.00 x 2.00 Inches | Weight: 0.02 Pounds
See On Amazon #2
Fulton 6 inch Long Forstner Bit Extension for Adding Over 5-5/8 inches of Drilling Depth to Your Forstner Bit. for Wood Turners, Furniture, Carpentry and Construction
Asin: B003UO7Y98 | Model: 927 | PartNumber: 927 | Ean: 0810948014492 | UPC: 810948014492
One Of The Most Common Uses For The Forstner Bit Extension Is For Woodturners Who Need To Bore Out Starter Holes On Larger Vessels. However, The Extension Works Exceptionally Well For Projects Like Salt Shakers, Pepper Mills Or Even Wood Turned Beverage Mugs. Contractors Use The Extension When They Need To Bore Deep Holes For Running Cables Or Wires And They Also Use It For Joining Larger Timbers..
The Collet Outside Diameter Is 25/32 Inch Without The Set Screws Protruding Outward. The Reason This Is Important Is That As We Mentioned Earlier, Some Bits May Have Slightly Different Shank Sizes. This Means The Set Screws May Protrude Outwardly From The Collet. The Minimum Size Hole This Extension Will Allow You To Drill Is 13/16 Inch. Forstner Bits And Machinery Shown In Pictures Are Not Included..
The Forstner Bit Extender Is Made From Solid, Heavy Duty Machined Steel. It Is Designed To Be Used With Forstner Bits Only. The Collet Inside Diameter Is 3/8 Inch. This Tolerance Is Very Tight And Designed To Accept Forstner Bits With Shank Sizes Of 3/8 Inch Or Slightly Smaller. Please Note That Some Forstner Bit Manufacturers Produce Bits That Say 3/8 Inch Shank Size When In Fact They Are Not. If You Measure Your Bit Shank And It Is 3/8 Inch, Your Bit Should Fit Once The Set Screws Are Loosened.
The Forstner Bit Extension Gives You Additional 5-5/8 Inches Of Reach To Bore Deeper Into Your Projects. This Will Help You Create Larger Diameter Starter Holes Or Help When You Need To Drill In Just A Little Further Than The Standard Bit Length Will Allow. The Extension Can Be Used With Forstner Bits On Drill Presses, Lathes With A Drill Chuck Installed (Drill Chuck Not Included) Or With A Power Drill..
Features
- Drilling with forstner bits to achieve a flat bottom hole or to start a deep hole turning project like on a larger vase or vessel is essentially impossible with a standard length forstner bit. To remedy this issue we have developed a heavy duty steel extension that allows you to secure a 3/8 inch shank forstner bit into the end collet.
- The forstner bit extension gives you additional 5-5/8 inches of reach to bore deeper into your projects. This will help you create larger diameter starter holes or help when you need to drill in just a little further than the standard bit length will allow. The extension can be used with forstner bits on drill presses, lathes with a drill chuck installed (drill chuck not included) or with a power drill.
- One of the most common uses for the forstner bit extension is for woodturners who need to bore out starter holes on larger vessels. However, the extension works exceptionally well for projects like salt shakers, pepper mills or even wood turned beverage mugs. Contractors use the extension when they need to bore deep holes for running cables or wires and they also use it for joining larger timbers.
- The forstner bit extender is made from solid, heavy duty machined steel. It is designed to be used with forstner bits only. The collet inside diameter is 3/8 inch. This tolerance is very tight and designed to accept forstner bits with shank sizes of 3/8 inch or slightly smaller. Please note that some forstner bit manufacturers produce bits that say 3/8 inch shank size when in fact they are not. If you measure your bit shank and it is 3/8 inch, your bit should fit once the set screws are loosened
- The collet outside diameter is 25/32 inch without the set screws protruding outward. The reason this is important is that as we mentioned earlier, some bits may have slightly different shank sizes. This means the set screws may protrude outwardly from the collet. The minimum size hole this extension will allow you to drill is 13/16 inch. Forstner bits and Machinery shown in pictures are NOT included.
- See more on Amazon...
Brand: Fulton | Manufacturer: Fulton Woodworking Tools and Accessories
See On Amazon #3
Peachtree Woodworking Supply Thin Rip Jig Table Saw Jig for Making Repetitive Narrow Strip Cuts on Table Saws with 3/4" x 3/8" Miter Slots Also Works with Many Router Tables and Band Saws
Asin: B0048J720U | Model: 3096 | PartNumber: 3096 | Ean: 0814310011034 | UPC: 814310011034
Making Your Thin Rip Cuts In This Fashion Allows You To Cut Wider Boards Down Without Getting Your Fingers In Harms Way By Keep Them Away From The Blade Or Cutter.The Thin Rip Works Much Like A Feather Except That It Doesn’T Exert Spring Like Pressure Against The Board. This Means It Can Be Used To Make Accurate, Repetitive Cuts Since It’S Essentially Just Holding Its Spot Once It Is Secured..
The Jig Can Be Used On Other Workshop Machinery Like Router Tables With Fences And Band Saws For Re-Saw Applications. In Certain Cases, When Working With Larger Or Longer Stock On Table Saws Or Router Tables, We Recommend Using Two Thin Rip Jigs Behind The Blade Or Cutter For Extra Stability When Feeding Your Stock Through..
The Thin Rip Jig Has A Roller Guide Bearing On The Tip To Make Feeding Your Stock Through An Easy And Smooth Moving Process. The Free Rotating Bearing Is Made From High Quality Materials For Extended Workshop Use. The Jig Fits Directly Into Most Any Standard 3/8” X 3/4” Miter Slot. The Body Is Made From A Solid Piece Of Aluminum And Is Adjustable Inward And Outward From Your Fence Depending On The Width Of Your Stock..
The Thin Rip Jig Acts Kind Of Like A Third Hand Behind The Blade Or Cutter. With The Saw Unplugged Simply Measure From The Outside Of Of The Blade Toward The Tip Of The (Guide Roller) Thin Rip Jig For The Width Cut You Want To Make. Once Set, Secure The Thin Rip Jig Simply By Rotating The Large, Easy To Grip Star Shaped Knob. After Your First Cut, Reset Your Stock Behind The Blade And Slide The Fence Over So Your Stock Piece Is Touching The Guide Roller On The Thin Rip Jig. Lock The Fence..
Features
- Making repetitive cuts on your table saw is a pretty straight forward process. Set your fence and feed each stock piece through the blade to achieve the same size each and every time. What if you need a series of narrow cuts that are about an 2 inches or less in width? Doing this can get tricky since you cant get your hands safely between the blade and the fence. You could always reverse measure and keep the off fall piece, but without a guide of some sort that can be inaccurate.
- The Thin Rip Jig acts kind of like a third hand behind the blade or cutter. With the saw unplugged simply measure from the outside of of the blade toward the tip of the (guide roller) Thin Rip Jig for the width cut you want to make. Once set, secure the Thin Rip Jig simply by rotating the large, easy to grip star shaped knob. After your first cut, reset your stock behind the blade and slide the fence over so your stock piece is touching the guide roller on the Thin Rip Jig. Lock the fence.
- Making your thin rip cuts in this fashion allows you to cut wider boards down without getting your fingers in harms way by keep them away from the blade or cutter.The Thin Rip works much like a feather except that it doesn t exert spring like pressure against the board. This means it can be used to make accurate, repetitive cuts since it s essentially just holding its spot once it is secured.
- The Thin Rip Jig has a roller guide bearing on the tip to make feeding your stock through an easy and smooth moving process. The free rotating bearing is made from high quality materials for extended workshop use. The jig fits directly into most any standard 3/8 x 3/4 miter slot. The body is made from a solid piece of aluminum and is adjustable inward and outward from your fence depending on the width of your stock.
- The jig can be used on other workshop machinery like router tables with fences and band saws for re-saw applications. In certain cases, when working with larger or longer stock on table saws or router tables, we recommend using two thin rip jigs behind the blade or cutter for extra stability when feeding your stock through.
- See more on Amazon...
Brand: Peachtree Woodworking Supply | Manufacturer: Peachtree Woodworking Supply Inc.
Dimensions: 3.00 x 4.00 x 3.00 Inches | Weight: 1.25 Pounds
See On Amazon #4
Micro-Mesh Pen Sanding Kit
Asin: B0037MEIT2 | Ean: 0725123001139 | UPC: 725123001139
The Results Are Truly Wonderful And Will Most Definitely Please The Most Discriminate Of Eyes. The Pack Includes 1 Each 2 Inch By 2 Inch Soft Touch Pads In The Following Grits: 1500, 1800, 2400, 3200, 3600, 4000, 6000, 8000 & 12000 Plus A Color Coded Grit Guide..
Works Great On Stabilized Woods, Acrylics & Solid Surface Materials. Pads Are Colored Coded With Foam Backing For Easy Grit Identification. Colors May Vary From Images Shown Here. The Colors On The Grit Chart And The Colors Of Micro-Mesh Abrasives May Vary Slightly Due To Color Shifts In The Manufacturing Process. 9 Micro-Mesh Pads Included..
Ideal For Use With Plastics, Resin Or Impregnated Blanks When Turning. The Pads Can Also Be Used Around The Home For Fine Repair Work..
This Pack Works Extremely Well When Working With Ca Finishes Leaving Your Work Looking Like It Was Done By A Professional! When Using The Pads It Is Recommended That Start At The Lower Grit Of 1500 And Step Or Cycle Your Way Up To The High Grit Of 12000..
Features
- Pen, Bottle Stopper or even small goblet finishing just became a bit more enjoyable with the Micro-Mesh Soft Touch sanding pads! Starting with the lowest grit of 1500 all the way up to 12000 grit this abrasive pad pack is sure the leave your project just the way you want it.
- This pack works extremely well when working with CA finishes leaving your work looking like it was done by a professional! When using the pads it is recommended that start at the lower grit of 1500 and step or cycle your way up to the high grit of 12000.
- The results are truly wonderful and will most definitely please the most discriminate of eyes. The pack includes 1 each 2 inch by 2 inch soft touch pads in the following grits: 1500, 1800, 2400, 3200, 3600, 4000, 6000, 8000 & 12000 plus a color coded grit guide.
- Ideal for use with plastics, resin or impregnated blanks when turning. The pads can also be used around the home for fine repair work.
- Works great on stabilized woods, acrylics & solid surface materials. Pads are colored coded with foam backing for easy grit identification. Colors may vary from images shown here. The colors on the grit chart and the colors of Micro-Mesh abrasives may vary slightly due to color shifts in the manufacturing process. 9 Micro-Mesh Pads included.
- See more on Amazon...
Brand: Micro-Mesh | Manufacturer: Micro-Surface Finishing Prod
Dimensions: 1.25 x 4.40 x 3.40 Inches | Weight: 0.02 Pounds
See On Amazon #5
Micro-Mesh 9 Sanding Sheet Introductory Woodworkers Kit with a 2 inch by 3 inch Foam Sanding Block
Asin: B000H6HIK2 | Model: 3KWPACK | PartNumber: 3KWPACK | Ean: 7241871045629, 0787721288473, 5915903721264, 0810948010463 | UPC: 810948010463, 787721288473
Micromesh Performs Very Well In Conjunction With Polyurethane, Polyester, Epoxy, Lacquer And So On. Follow The Manufacturer’S Recommended Cure Times Prior To Re-Coating Or Applying The Finish Coat. When You Are Applying Multiple Coats, Sand From 1500 Micro-Mesh To 3200 Or 3600 Between Coats To Remove Any Orange-Peel Or Dirt. After The Final Coat Has Fully Cured, Polish The Surface Beginning With 2400 Micro-Mesh And Continue Through The Series (3200-12000) Until The Desired Gloss Is Achieved..
🇺🇸 This Made In The Usa Kit Includes: 1 Each Of The Following Grit 3 Inch By 4 Inch Sheets: 1500, 1800, 2400, 3200, 3600, 4000, 6000, 8000 And 12000. Also Included Is A 2 Inch By 3 Inch Foam Sanding Block. Micro-Mesh Can Be Used Wet Or Dry..
Satin Finishes Are Achieved By Sanding Up To The 3600 Grade. The Satin Finish Gets Progressively Higher In Gloss Through The 6000 Step. High Gloss Finishes Will Appear By The 6000 Through 12000 Step. The Wood, The Finish Used And Personal Preference Determine Where To Stop. Micro-Gloss Liquid Abrasive Can Be Hand Rubbed Onto The Finish Following The 12000 Micro-Mesh Step For An “Ultra” High Gloss Finish..
Before Starting The Micro-Mesh Cycle Of Abrasive Sanding, Coarse Sanding Should Be Done Using Up To 320 Grit Sandpaper. Shaping, Sawing Or Turning Of The Work Piece Should Be Complete.Begin With 1500 Micro-Mesh. Sand Until All Of The Sandpaper Scratches Are Removed. Continue With The Micro-Mesh Series And Cycle Up To The Desired Look (1800, 2400, 3200, 3600, 4000, 6000, 8000, 12000). Thinned Lemon Oil Or Danish Oil Can Be Applied As A Finish On Bare Wood..
Features
- Micro-Mesh is a unique cushioned abrasive that produces a very fine and uniform scratch pattern. The nine grades of abrasives range from 1500 grit to 12000 grit. The 1500 is similar in grit range to conventional 400 grit wet/dry sandpaper. The 12000 will leave a scratch pattern that cannot be detected by the human eye and produces a wonderful looking finish. Micro-Mesh abrasives can polish to a high reflective state or leave a matte or satin finish depending upon where you stop.
- Before starting the Micro-Mesh cycle of abrasive sanding, coarse sanding should be done using up to 320 grit sandpaper. Shaping, sawing or turning of the work piece should be complete.Begin with 1500 Micro-Mesh. Sand until all of the sandpaper scratches are removed. Continue with the MICRO-MESH series and cycle up to the desired look (1800, 2400, 3200, 3600, 4000, 6000, 8000, 12000). Thinned lemon oil or Danish oil can be applied as a finish on bare wood.
- MicroMesh performs very well in conjunction with polyurethane, polyester, epoxy, lacquer and so on. Follow the manufacturer s recommended cure times prior to re-coating or applying the finish coat. When you are applying multiple coats, sand from 1500 Micro-Mesh to 3200 or 3600 between coats to remove any orange-peel or dirt. After the final coat has fully cured, polish the surface beginning with 2400 Micro-Mesh and continue through the series (3200-12000) until the desired gloss is achieved.
- Satin finishes are achieved by sanding up to the 3600 grade. The satin finish gets progressively higher in gloss through the 6000 step. High gloss finishes will appear by the 6000 through 12000 step. The wood, the finish used and personal preference determine where to stop. Micro-Gloss liquid abrasive can be hand rubbed onto the finish following the 12000 Micro-Mesh step for an ultra high gloss finish.
- This Made In the USA KIT INCLUDES: 1 each of the following grit 3 inch by 4 inch sheets: 1500, 1800, 2400, 3200, 3600, 4000, 6000, 8000 and 12000. Also included is a 2 inch by 3 inch foam sanding block. Micro-Mesh can be used wet or dry.
- See more on Amazon...
Brand: Micro Mesh | Manufacturer: Micro-Surface Finishing
Dimensions: 2.00 x 6.00 x 2.60 Inches | Weight: 0.08 Pounds
See On Amazon #6
Fulton Woodworking Tools 129 Piece Bowl Sanding Mandrel Disc Kit with Round Discs
Asin: B08375RNR3 | Model: 334 | PartNumber: 334 | Ean: 0817918022525 | UPC: 817918022525
Features
- Sanding curved surfaces like wooden bowls can be challenging and can take a long time to finish when sanding by hand. Sanding your project by hand can also cause fatigue and produce unsatisfactory results. The shank sanding mandrels have a thick padded base that conforms to concave or convex surfaces. Simply secure the mandrel into a variable speed drill or flexible shaft and you re ready to go
- See more on Amazon...
Brand: Fulton | Manufacturer: Peachtree Woodworking Supply Inc.
Dimensions: 0.10 x 3.00 x 2.00 Inches
See On Amazon #7
Peachtree Woodworking Supply Pen Blank Centering Vise for Drilling Center Holes in Pen Blanks Using a Drill Press
Asin: B003VHWKYS | Model: 7003 | PartNumber: 7003 | Ean: 0814310010211 | UPC: 814310010211
Just Set Up The Vise Once And Drill All Of Your Blanks In The Exact Center. There Is No Need To Change The Setup Regardless Of The Blanks Size Or Shape..
The Scrap Piece Can Be Flipped, Slid And Reversed To Get Numerous Uses Out Of A Single Piece. When You Use Up All Of The Surface, Simply Cut Another Piece Out Of 1/4" Thick Stock. Wooden Base Is Removable And Replaceable. If You Need A Larger Base To Clamp The Vise To Your Drill Press, Simply Remove The Wooden Base And Replace It With A Base Made To Your Exact Specifications.
Holds Blanks Up To 1-1/2" Square. The Pen Center Vise Includes A Scrap Board Piece Of Mdf. It Measures Approximately 2" By 1/4"..
The Jaws On The Drilling Center Move In And Out Simultaneously To Insure Precision Center Drilling Of Your Blanks Each And Every Time You Use The Vise..
Features
- Easily locate and drill pen blank centers and Drill through the exact center of your pen blanks with this simple but effective Pen Centering vise. By far one of the best selling pen vises available, this jig will be a go to tool when turning your pens.
- The jaws on the drilling center move in and out simultaneously to insure precision center drilling of your blanks each and every time you use the vise.
- Just set up the vise once and drill all of your blanks in the exact center. There is no need to change the setup regardless of the blanks size or shape.
- Holds blanks up to 1-1/2 square. The pen center vise includes a scrap board piece of mdf. It measures approximately 2 by 1/4.
- The scrap piece can be flipped, slid and reversed to get numerous uses out of a single piece. When you use up all of the surface, simply cut another piece out of 1/4 thick stock. Wooden base is removable and replaceable. If you need a larger base to clamp the vise to your drill press, simply remove the wooden base and replace it with a base made to your exact specifications
- See more on Amazon...
Brand: Peachtree Woodworking Supply | Manufacturer: Peachtree Woodworking Supply Inc.
See On Amazon #8
MICROJIG GRR-RIPPER SP-2TK Mj Splitter Steelpro Tk
Asin: B00B03PMY0 | Model: SP-2-TK | PartNumber: SP-2-TK | Ean: 7241870774766, 0815267010262, 0787721614722, 5915903681346 | UPC: 815267010262, 787721614722
Finally, A Table Saw Splitter That Is Easy To Install, Easy To Use, Easy To Align, And Doesn't Get In The Way.
For 10" Thin Kerf Saw Blades.
Tough To The Core. The Mj Splitter Steelpro Tk Has 100% Polycarbonate Shell Reinforced With A Solid Stainless Steel Foundation. Able To Take On The Stress Caused By Many Solid Woods. The Steelpro Will Greatly Reduce The Chance Of Kickback On Your Table Saw And Virtually Eliminate Burning.
Table Saw Safety For Your Toughest Cuts.
Features
- Precision splitters made with stainless steel.
- Table saw safety for your toughest cuts
- Finally, a table saw splitter that is easy to install, easy to use, easy to align, and doesn't get in the way
- Tough to the core. The MJ Splitter SteelPro TK has 100% polycarbonate shell reinforced with a solid stainless steel foundation. Able to take on the stress caused by many solid woods. The SteelPro will greatly reduce the chance of kickback on your table saw and virtually eliminate burning
- For 10 Thin Kerf Saw Blades
- See more on Amazon...
Brand: MICRO JIG | Manufacturer: MICROJIG, Inc.
Dimensions: 4.00 x 4.00 x 0.50 Inches | Weight: 0.35 pounds
Warranty: Extended 3-Year Manufacturer's Warranty from Authorized Dealers Only
See On Amazon #9
3 x 4 Micro-Mesh TM Sanding Pads 9 Grits
Asin: B0756MT6X8 | Model: 3 x 4 Soft Pads | PartNumber: 3 x 4 Soft Pads
The Pack Includes 9 Each 3 Inch By 4 Inch Soft Touch Pads In The Following Grits: 1500, 1800, 2400, 3200, 3600, 4000, 6000, 8000 & 12000 Plus A Color Coded Grit Guide..
Pads Are Colored Coded With Foam Backing For Easy Grit Identification. Colors May Vary From Images Shown Here. The Colors On The Grit Chart And The Colors Of Micro-Mesh Abrasives May Vary Slightly Due To Color Shifts In The Manufacturing Process..
Ideal For Use With Acrylics, Plastics, Resin Or Impregnated Blanks When Turning. Works Great On Automotive And Marine Body Work. The Pads Can Also Be Used Around The Home For Fine Repair Work..
This Pack Works Extremely Well When Working With Ca Finishes Leaving Your Work Looking Like It Was Done By A Professional! Using The Step Up Process Will Leave Your Project Finish Looking Wonderful ..
Features
- Pen, Bottle Stopper or even small goblet finishing just became a bit more enjoyable with the Micro-Mesh Soft Touch sanding pads! Start with the lowest grit of 1500 all the way up to 12000 grit.
- This pack works extremely well when working with CA finishes leaving your work looking like it was done by a professional! Using the step up process will leave your project finish looking wonderful .
- The pack includes 9 each 3 inch by 4 inch soft touch pads in the following grits: 1500, 1800, 2400, 3200, 3600, 4000, 6000, 8000 & 12000 plus a color coded grit guide.
- Ideal for use with acrylics, plastics, resin or impregnated blanks when turning. Works great on automotive and marine body work. The pads can also be used around the home for fine repair work.
- Pads are colored coded with foam backing for easy grit identification. Colors may vary from images shown here. The colors on the grit chart and the colors of Micro-Mesh abrasives may vary slightly due to color shifts in the manufacturing process.
- See more on Amazon...
Brand: Micro-Mesh | Manufacturer: Micro-Surface
Dimensions: 0.10 x 3.00 x 4.00 inches | Weight: 4.00 ounces
See On Amazon #10
Peachtree Woodworking Supply 2 inch by 2 inch Micro-Mesh Soft Touch Sanding Pads w/ Galvanized Steel Dispenser - for Pen & Bottle Stopper Turning, Cycle Sanding Acrylic Materials (9 Micro Mesh Pads)
Asin: B07PTBBL9B | Model: VN-309-11554 | PartNumber: VN-309-11554 | Ean: 0817918022136 | UPC: 817918022136
Specifically Designed For The Micro-Mesh 2” X 2” 9 Pack Of Abrasives, This Dispenser Has Color Coded Grit Chart To Help Keep Your Pads In Order. This Works Wonderfully Well When Step Sanding Your Finished Turning Project. Simply Cycle Your Way Through The Grits By Pulling The Next Grit From The Dispenser And Placing The Used One Back On Top..
The Dispenser Measures 6” Tall, 3¼” Wide (At Base Tabs), 2-7/16” Wide (Actual Abrasive Holder) By 1½” Deep. The Colors On The Grit Chart And The Colors Of Micro-Mesh Abrasives May Vary Slightly Due To Color Shifts In The Manufacturing Process. Package Comes With 9 Color Coded Micro Mesh Pads And 1 Each Galvanized Steel Dispenser..
The Dispenser Is Made From Corrosion Resistant Galvanized Steel Which Also Makes It Extra Durable For The Workshop Environment. It Can Be Mounted Flat Against A Wall Or It Can Be Mounted To A Table Top. Of Course You Don’T Have To Mount It At All..
When Using The Pads It Is Recommended That Start At The Lower Grit Of 1500 And Step Or Cycle Your Way Up To The High Grit Of 12000. The More You Get Into To Woodturning The More The Reality Of Being Organized Comes Into Play. This Couldn’T Be More True Than When It Comes To Our Abrasives. This Unique Dispenser Accepts 2” X 2” Micro-Mesh Abrasive Pads.
Features
- Pen, Bottle Stopper or even small goblet finishing just became a bit more enjoyable with the Micro Mesh Soft Touch sanding pads! Starting with the lowest grit of 1500 all the way up to 12000 grit this abrasive pad pack is sure the leave your project just the way you want it. This pack works extremely well when working with CA finishes leaving your work looking like it was done by a professional!
- When using the pads it is recommended that start at the lower grit of 1500 and step or cycle your way up to the high grit of 12000. The more you get into to woodturning the more the reality of being organized comes into play. This couldn t be more true than when it comes to our abrasives. This unique dispenser accepts 2 x 2 Micro-Mesh abrasive pads
- Specifically designed for the Micro-Mesh 2 x 2 9 pack of abrasives, this dispenser has color coded grit chart to help keep your pads in order. This works wonderfully well when step sanding your finished turning project. Simply cycle your way through the grits by pulling the next grit from the dispenser and placing the used one back on top.
- The dispenser is made from corrosion resistant galvanized steel which also makes it extra durable for the workshop environment. It can be mounted flat against a wall or it can be mounted to a table top. Of course you don t have to mount it at all.
- The dispenser measures 6 tall, 3 wide (at base tabs), 2-7/16 wide (actual abrasive holder) by 1 deep. The colors on the grit chart and the colors of Micro-Mesh abrasives may vary slightly due to color shifts in the manufacturing process. Package comes with 9 color coded micro mesh pads and 1 each galvanized steel dispenser.
- See more on Amazon...
Brand: Peachtree Woodworking Supply | Manufacturer: Peachtree Woodworking Supply inc.
See On Amazon #11
Keystone 2" Diameter Flex Edge Gold Hook and Loop Wavy Sanding Disc Single Grit 25 Pack 220 Grit
Asin: B0CDCFN56Q | Ean: 0817918023706 | UPC: 817918023706
These Discs Are Perfect For Wood Turning, Auto Body, Marine Work, Metal Working, Arts And Crafts, Household, Drywall, Industrial, Fiberglass, Plastics, General Woodworking, Furniture Or Most Any Other Flat Or Curved Surface That Needs Sanding..
Available In 10 Different Grits: 60, 80, 100, 120, 150, 220, 320, 400, 600, And 800. Each Pack Contains 25 Of Each Grit And Each Grit Is Available In Your Choice Of Three Diameters Which Are: 1”, 2” Or 3”. These Are Hook And Loop Backed Discs And Will Not Work With Psa (Pressure Sensitive Adhesive) Sanders..
The Flex Edge Gold Sanding Disc Not Only Delivers An Exceptionally Long Lasting Sharp Cut, It Produces A Consistent “Scratch Pattern” For Consistent Results Each Time You Use Them. The Discs Are Made With A Coated Aluminum Oxide That Is Fused With Zirconia Aluminum For An Exceptional Long Lasting Bond. This Process Helps The Sanding Disc Resist Clogging, Loading Or Pilling Which Helps Increase Longevity And Decreases Overall Consumption..
With Our Unique Flex Edge Sanding Discs, You Don’T Have To Worry About Sliding Or Shifting Of The Sanding Disc Any Longer! The Flex Edge Sanding Disc Is Made Slightly Larger For Starters And Each Disc Has Wavy Tabs All Around The Entire Circumference Of The Disc. Each Tab Wraps Around The Edge Of A Sanding Head Unit. This Prevents The Hard Hook Material Of The Head Unit From Touching Your Project!.
Features
- Sanding wood turned bowls, platters, marine surfaces, auto body touch ups, concave surfaces or any surface with a drill mounted sanding head or wood handle bowl sander can produce wonderful results! However, one of the issues with this sanding process is that the disc tends to shift while in use causing unsightly marks to your project and likely damaging you sander if you re not careful.
- With our unique Flex Edge Sanding Discs, you don t have to worry about sliding or shifting of the sanding disc any longer! The Flex Edge Sanding Disc is made slightly larger for starters and each disc has wavy tabs all around the entire circumference of the disc. Each tab wraps around the edge of a sanding head unit. This prevents the hard hook material of the head unit from touching your project!
- These discs are perfect for wood turning, auto body, marine work, metal working, arts and crafts, household, drywall, industrial, fiberglass, plastics, general woodworking, furniture or most any other flat or curved surface that needs sanding.
- The Flex Edge Gold Sanding Disc not only delivers an exceptionally long lasting sharp cut, it produces a consistent scratch pattern for consistent results each time you use them. The discs are made with a coated aluminum oxide that is fused with zirconia aluminum for an exceptional long lasting bond. This process helps the sanding disc resist clogging, loading or pilling which helps increase longevity and decreases overall consumption.
- Available in 10 different grits: 60, 80, 100, 120, 150, 220, 320, 400, 600, and 800. Each pack contains 25 of each grit and each grit is available in your choice of three diameters which are: 1 , 2 or 3 . These are hook and loop backed discs and will not work with PSA (Pressure Sensitive Adhesive) sanders.
- See more on Amazon...
Brand: Keystone | Manufacturer: Peachtree Woodworking Supply
See On Amazon #12
Peachtree Woodworking Supply 2 inch Foam Brush 24 Pack for Painting Staining Varnishing and General Finishing Projects Made in The USA
Asin: B000H5AG66 | Model: 1184 | PartNumber: 1184 | Ean: 0810948012962, 0817918022693 | UPC: 810948012962, 817918022693
If You’Re A Woodworker Or Have Worked With Wood Projects, Then You Already Know The Value Of Having Foam Brushes On Hand. Staining And Varnishing Wood Is A Fantastic Way To Use Foam Brushes. Simply Dip The Brush Into The Prepared Stain And Apply In Even Strokes Or Drizzle A Little Stain On The Wood And Quickly Spread It In Long, Even Strokes. A Rag Can Be Used To Wipe Off Excess Stain, Or You Can Flip The Brush Over To Remove Excess Stain..
These Foam Brushes Have A Chiseled Profile To Make Getting Into Tight Spaces Much Easier Than Standard Bristle Brushes. This Also Makes Foam Brushes Ideal For Touch Up Work On Walls, Baseboards And Corners. This Foam Brush Profile Also Works Great For Working On Models And Smaller Projects Where Precision Is Needed. These Brushes Are Proudly Made In The Usa And Hold Their Rigidity Better Than Most Brands That Are Made Overseas..
These Brushes Are Also Ideal For Home Painting Projects Where The Appearance Of Brush Strokes Are Not A Desired Finished Look. They Will Work With Latex And Oil Based Paints And Typically Apply Paint With Fewer Strokes Saving You Time. Each Brush Attached To A Wooden Dowel Style Handle And Is Lightweight For Les Hand Fatigue When Working On Larger Projects..
Foam Brushes Produce A Smooth, Brush-Stroke-Free Appearance To Your Project When Finished. A Smooth Appearance Is Desirable For Many Different Projects Like When Working On Furniture, Cabinetry, Trim, Model Work, Metal Work, Indoor Applications, Outdoor Applications And A Whole Lot More. Not Recommended For Use With Shellac Or Lacquer Applications..
Features
- Why use a foam brush versus a standard bristle paint brush? That s a question people ask themselves all the time. The simple answer is you should use both. While using bristle brushes for larger areas and using foam brushes for cut-ins is a common use, foam brushes can be used for quite a few applications throughout the home, shop or workplace.
- Foam brushes produce a smooth, brush-stroke-free appearance to your project when finished. A smooth appearance is desirable for many different projects like when working on furniture, cabinetry, trim, model work, metal work, indoor applications, outdoor applications and a whole lot more. Not recommended for use with shellac or lacquer applications.
- If you re a woodworker or have worked with wood projects, then you already know the value of having foam brushes on hand. Staining and varnishing wood is a fantastic way to use foam brushes. Simply dip the brush into the prepared stain and apply in even strokes or drizzle a little stain on the wood and quickly spread it in long, even strokes. A rag can be used to wipe off excess stain, or you can flip the brush over to remove excess stain.
- These brushes are also ideal for home painting projects where the appearance of brush strokes are not a desired finished look. They will work with latex and oil based paints and typically apply paint with fewer strokes saving you time. Each brush attached to a wooden dowel style handle and is lightweight for les hand fatigue when working on larger projects.
- These foam brushes have a chiseled profile to make getting into tight spaces much easier than standard bristle brushes. This also makes foam brushes ideal for touch up work on walls, baseboards and corners. This foam brush profile also works great for working on models and smaller projects where precision is needed. These brushes are proudly MADE IN THE USA and hold their rigidity better than most brands that are made overseas.
- See more on Amazon...
Brand: Peachtree Woodworking Supply | Manufacturer: Peachtree Woodworking Supply Inc
Weight: 0.00 pounds
See On Amazon #13
Peachtree Woodworking Supply Spindle Drum Sander Sleeve Assortment Pack 12 Total Sleeves 2 inches in Length. Made in The USA
Asin: B000H684N2 | Model: PW114 | PartNumber: PW114 | Ean: 0810948011750 | UPC: 810948011750
1 Each 80, 120, 150 Grit For 1” X 2” Sleeve.
1 Each 80, 120, 150 Grit For 1-1/2” X 2” Sleeve.
1 Each 80, 120, 150 Grit For 3/4” X 2” Sleeve.
Features
- 1 each 80, 120, 150 Grit for 1/2" x 2 Sleeve
- 1 each 80, 120, 150 Grit for 3/4 x 2 Sleeve
- 1 each 80, 120, 150 Grit for 1 x 2 Sleeve
- 1 each 80, 120, 150 Grit for 1-1/2 x 2 Sleeve
- See more on Amazon...
Brand: Peachtree Woodworking Supply | Manufacturer: Peachtree Woodworking Supply Inc.
See On Amazon #14
Peachtree Woodworking Supply 2 inch Wide Pinch Dogs Made from Solid Steel and Textured for Better Holding Power (10 Pack of 2 inch Pinch Dogs)
Asin: B00JJZACQE | Model: 802 | PartNumber: 802 | Ean: 0814310011263 | UPC: 814310011263
The Second Method Typically Takes Some Planning To Be Sure That We Are Not Marking Up The Good Side Of Our Workpiece. With Your Boards Laying Flat, Tap A Pinch Dog Into The Flat Side Of Your Panel Along The Seem Every Couple Of Inches. Tap In As Many As Needed To Achieve A Tight Fitting Joint. This Method Is Most Commonly Used On Table Tops Where The Pinch Dog Marks Are Either Concealed By Other Project Pieces Or Won’T Be Seen Since The Marks Are Out Of Plain View..
The Fulton Pinch Dogs Are Made From Solid Steel To Ensure Long Lasting Durability And Each Dog Is Lightly Textured To Provide Some “Bite” So They Wont Slip Out Like Some Of The Coated Versions You May Find. Each Pinch Dog Comes To A Tapered Point On Each Side To Help Pull Your Stock In Toward The Center Of The Pinch Dog To Give The Best Clamping Results Possible. Pack Includes 10 Each Of The Same Size Pinch Dogs. Size Denotes Distance Between Tapered Point Tips..
One Of The Great Advantages That Pinch Dogs Have Over Most Any Other Clamping Device Is That They Are A Very Economically Priced Clamp. Typically The Come In Multi Packs Which Makes Owning A Lot Of These Little Clamps Much Easier To Swallow Than Having To Cough Of High Dollars For Pipe Or Bar Clamps. Another Great Advantage Is That Pinch Dogs Are Tiny In Comparison To Other Clamps. When You’Re Not Using Them, Simply Place Them In The Corner Of A Drawer..
Pinch Dogs Can Be Used In Two Basics Ways. The Most Common Method Is To Tap The Pinch Dog Into The End Grain Of Two Boards With One Of The Points Of The Pinch Dog On One Board And The Other Point Of The Pinch Dog On The Other Board. The Pinch Dog Has Two Tapered Points That Pull The Wood Toward The Center Of The Pinch Dog As It Is Driven Into The Wood. The More You Tap The Pinch Dog Into The Wood, The Tighter The Fit Becomes..
Features
- As the old saying goes; you can never have too many clamps if you re a woodworker. This holds especially true when it comes to achieving near seamless or tight fitting joinery. While using long bar clamps or pipe clamps to glue up panels will work, sometimes you may need a helping hand or pinch in certain cases to get the seem just right. Using pinch dogs to pull your or pinch the panel joint together is an old tried and true method that is still commonly used today.
- Pinch dogs can be used in two basics ways. The most common method is to tap the pinch dog into the end grain of two boards with one of the points of the pinch dog on one board and the other point of the pinch dog on the other board. The pinch dog has two tapered points that pull the wood toward the center of the pinch dog as it is driven into the wood. The more you tap the pinch dog into the wood, the tighter the fit becomes.
- The second method typically takes some planning to be sure that we are not marking up the good side of our workpiece. With your boards laying flat, tap a pinch dog into the flat side of your panel along the seem every couple of inches. Tap in as many as needed to achieve a tight fitting joint. This method is most commonly used on table tops where the pinch dog marks are either concealed by other project pieces or won t be seen since the marks are out of plain view.
- One of the great advantages that pinch dogs have over most any other clamping device is that they are a very economically priced clamp. Typically the come in multi packs which makes owning a lot of these little clamps much easier to swallow than having to cough of high dollars for pipe or bar clamps. Another great advantage is that pinch dogs are tiny in comparison to other clamps. When you re not using them, simply place them in the corner of a drawer.
- The Fulton Pinch Dogs are made from solid steel to ensure long lasting durability and each dog is lightly textured to provide some bite so they wont slip out like some of the coated versions you may find. Each pinch dog comes to a tapered point on each side to help pull your stock in toward the center of the pinch dog to give the best clamping results possible. Pack includes 10 each of the same size pinch dogs. Size denotes distance between tapered point tips.
- See more on Amazon...
Brand: Peachtree Woodworking Supply | Manufacturer: Peachtree Woodworking Supply Inc.
See On Amazon #15
1/2" Robert Sorby #840H Spindle Gouge
Asin: B0036B67ZM | Model: 840H-1/2 | PartNumber: 840H-1/2 | Ean: 5013035027084
Come With Hard White Ash Handle And Brass Ferrule.
Overall Length Is 18 1/4 Inches.
Standard Handle Is 12 Inches Long With Tool Being 6 1/4 Inches In Length.
Steel Will Resist "Blued” Softening From Overheating During Grinding Or Heavy Use.
Features
- Made from hardened and tempered high speed steel that that will keep a sharpened edge about six times longer than carbon steel
- Steel will resist blued softening from overheating during grinding or heavy use
- Come with hard White Ash handle and brass ferrule
- Standard handle is 12 inches long with tool being 6 1/4 inches in length
- Overall length is 18 1/4 inches
- See more on Amazon...
Brand: Mingtawn | Manufacturer: Robert Sorby
Dimensions: 19.25 x 3.40 x 19.25 Inches
See On Amazon #16
Authentic Easy Wood Tools Ci1-R2 Square Carbide Replacement Cutter with 2" Radius for Full and Pro Size Roughers Lathe Woodturning Tools Ci1-R2
Asin: B07B4L4FCB | Model: 1600 | PartNumber: 1600 | Ean: 0811269020704 | UPC: 811269020704
The Perfect Grade Of Carbide Produces The Best Combination Of Sharpness And Durability. Optimal Grinding Process Produces The Flattest And Truest Cutting Surfaces. The Right Geometry Or Cutting Angle Is Ground To The Produce An Edge The Cuts Cleanly And Safely..
Designed And Manufactured 100% In The Usa.
Be Sure To Check Out Our Ci-R2-Nr - Patented Negative Rake Carbide Cutter - 1600Nr (Sold Separately) When You Are Ready To Turn Resins, Acrylics, Extreme Hardwood, And/Or Any Man-Made Materials. Dramatically Reduces Chipping, Catches And Blowouts When Used Properly..
No Stopping, No Sharpening, No Need To Purchase Expensive Re-Sharpening Equipment, No Hassle. Replace Your Cutters, Not Your Whole Tool, For A Lower Total Cost Of Ownership!.
Features
- Authentic Easy Wood Tools Ci1-R2 Carbide Cutter is designed to fit Full and Pro Size roughers. Comes with new 8-32 screw.
- No stopping, no sharpening, no need to purchase expensive re-sharpening equipment, no hassle. Replace your cutters, not your whole tool, for a lower total cost of ownership!
- The perfect grade of carbide produces the best combination of sharpness and durability. Optimal grinding process produces the flattest and truest cutting surfaces. The right geometry or cutting angle is ground to the produce an edge the cuts cleanly and safely.
- Be sure to check out our Ci-R2-NR - Patented Negative Rake Carbide Cutter - 1600NR (sold separately) when you are ready to turn Resins, Acrylics, Extreme Hardwood, and/or any Man-Made materials. Dramatically reduces chipping, catches and blowouts when used properly.
- Designed and Manufactured 100% in the USA
- See more on Amazon...
Brand: Easy Wood Tools | Manufacturer: Easy Wood Tools
Dimensions: 0.59 x 0.39 x 0.10 Inches | Weight: 0.01 pounds
See On Amazon #17
Peachtree Woodworking Supply Round Knob with 2" Stud 3/8" x 16-4 Pack - PW6109
Asin: B000UH31IG | Ean: 0810948012504 | UPC: 810948012504
Replacement For That Lost Knob.
4 Knobs Per Package..
Thread Inserts Are Steel For Long Life.
Can Be Used For Shop Made Jigs.
Features
- High Quality 3/8" x 16 Round Knob with 2" Stud
- Can be used for shop made jigs
- Replacement for that lost knob
- Thread inserts are steel for long life
- 4 knobs per package.
- See more on Amazon...
Brand: Peachtree Woodworking Supply | Manufacturer: Peachtree Woodworking Supply Inc.
Dimensions: 0.01 x 16.00 x 8.00 inches
See On Amazon #18
Easy Wood Tools Mini Easy Rougher (5200) Woodturning Tools with Replaceable Carbide Cutter
Asin: B003A04RQ0 | Model: 5200 | PartNumber: 5200 | Ean: 0811269020322 | UPC: 811269020322
Optional Ewt Cutters Available: Ci2-R2 (W/2" Radius Ground On All 4 Flat Turning Surfaces) Square And Ci2-R2-Nr Patented Negative Rake Square (W/2" Radius Ground On All 4 Flat Turning Surfaces) Carbide Cutter For Turning Resins, Acrylics, Extreme Hardwoods And Other Man-Made Materials.
Designed And Manufactured 100% In The Usa.
Easy Wood Tools Have Lower Cost Of Ownership - All You Need Is A Lathe And Easy Wood Tools...No Need To Purchase Expensive Sharpening Equipment And Tools That Will Eventually Need Replacing Due To They Become Too Short To Re-Sharpen. Our Tools Are Also Designed To Be Safer (Than High Speed Steel) By Holding Them Horizontal, On Center To The Workpiece And Flat On The Tool Rest..
The Square (Roughing) Cutters On All Ewt Roughers Are Designed To Remove Material In Bulk And To Cut Tenons..
Features
- Ergonomic Hardwood Maple Handle: 12" Maple / Tool Bar: 3/8" x 4" / Overall length 16" / Max Reach: 2". Comes mounted with a Ci2-Square.
- The square (roughing) cutters on all EWT Roughers are designed to remove material in bulk and to cut tenons.
- Optional EWT Cutters Available: Ci2-R2 (w/2 radius ground on all 4 flat turning surfaces) Square and Ci2-R2-NR Patented Negative Rake Square (w/2 radius ground on all 4 flat turning surfaces) Carbide Cutter for turning Resins, Acrylics, Extreme Hardwoods and other Man-Made materials
- Easy Wood Tools have Lower Cost of Ownership - All you need is a lathe and Easy Wood Tools...no need to purchase expensive sharpening equipment and tools that will eventually need replacing due to they become too short to re-sharpen. Our tools are also designed to be safer (than High Speed Steel) by holding them horizontal, on center to the workpiece and flat on the tool rest.
- Designed and Manufactured 100% in the USA
- See more on Amazon...
Brand: Easy Wood Tools | Manufacturer: Easy Wood Tools
Dimensions: 0.59 x 0.79 x 0.10 Inches | Weight: 0.75 Pounds
See On Amazon #19
Fulton Universal Aluminum Miter Gauge Fence with an Aluminum Flip Stop 18 Left Reading Tape 18 Right Reading Tape
Asin: B08DL6YCSJ | Model: 11563 | PartNumber: 11563 | Ean: 0817918022372 | UPC: 817918022372
Many Times When We Make Miter Cuts On Our Table Saw, We Need 2 Or More Pieces That Are The Exactly Same Length. While Using The Included Measuring Tapes That Are Included Are Pretty Good At This, We Have Also Included A Handy Flip Stop That Locks Into Any Location Along The Length Of The Fence. This Allows You To Make Repetitive Length Cuts Without Worrying If The Pieces Will End Up The Same. The Flip Stop Can Can Simply Be Flipped It Up And Out Of Your Way When Not In Use..
The Fence Can Be Mounted To Low Profile Miter Gauges Or Standard Profile Miter Gauges Simply By Flipping The Fence Over To Accommodate Your Miter Gauge. This Fence Will Fit Most Available After Market And Factory Table Saw Miter Gauges, However Some Modification May Be Required. Full Color Installation Instructions Are Included..
The Fulton Aluminum Miter Fence Is Made From One, Solid Piece Of Extruded Aluminum And Has The Exact Same Size Track On The Top Of The Fence As There Is On The Bottom. On The Back, There Is An Offset Track For Mounting The Fence To A Miter Gauge..
The Aluminum Miter Fence Has Been Cut At 45 Degrees On Both Ends Of The Fence. Doing This Allows You To Get As Close To The Blade As Possible So Your Workpiece Is Fully Supported Throughout The Cutting Process. Straight Cut Or 90 Degree Cut Fences Have A Large Gap Between The Fence And The Blade Because It Can Not Get As Close With The Straight Cut Ends On The Fence..
Features
- When cutting mitered angles with your table saw you always want to make sure that have enough support of your stock when feeding it through the blade. The table saw blade is rotating toward you at a high rate of speed and if your workpiece moves to the side, the result can be scary and downright dangerous. With the help of a miter gauge and with our Aluminum Miter Fence secured to it, you will have full support all the way up to the blade on most of your miter angle cuts.
- The Aluminum Miter Fence has been cut at 45 degrees on both ends of the fence. Doing this allows you to get as close to the blade as possible so your workpiece is fully supported throughout the cutting process. Straight cut or 90 degree cut fences have a large gap between the fence and the blade because it can not get as close with the straight cut ends on the fence.
- Many times when we make miter cuts on our table saw, we need 2 or more pieces that are the exactly same length. While using the included measuring tapes that are included are pretty good at this, we have also included a handy flip stop that locks into any location along the length of the fence. This allows you to make repetitive length cuts without worrying if the pieces will end up the same. The flip stop can can simply be flipped it up and out of your way when not in use.
- The Fulton Aluminum Miter Fence is made from one, solid piece of extruded aluminum and has the exact same size track on the top of the fence as there is on the bottom. On the back, there is an offset track for mounting the fence to a miter gauge.
- The fence can be mounted to low profile miter gauges or standard profile miter gauges simply by flipping the fence over to accommodate your miter gauge. This fence will fit most available after market and factory table saw miter gauges, however some modification may be required. Full color installation instructions are included.
- See more on Amazon...
Brand: Fulton | Manufacturer: Fulton Woodworking Tools and Accessories
Weight: 2.25 pounds
See On Amazon
Looking For Something Else?
Search