RATTMMOTOR 4 Axis CNC Controller Stepper Motor Kit, Nema23 Stepper Motor 270oz-in 3A Dual Shaft with Brackets, TB6600 Stepper Motor Driver, CNC Motion Control Board Mach3 USB Card, 24V Power Supply
Asin: B09VKV26CW | Model: 4 Axis | PartNumber: 4 Axis
As an Amazon Associate we earn a fee from qualifying purchases when you follow a link to Amazon from this page. We rank the products, but the links to Amazon are promotional.【Low Noise/High Torque Hybrid Stepper Motor】23Hs8430b 2-Phase Stepper Motor With Dual Shaft Diameter Of 8Mm, A Current Of 3A And An Angle Of 1.8°, Is Made Of Durable Metal On The Outside, And The Perfect Combination Of Rubber And Rotor Fills Up The Inner Space And Stabilizes The Overall Structure Of The Motor. The Coils Are Made Of Pure Copper Enameled Wire And The Torque Is Up To 270Oz-In (180N.Cm/18Kg-Cm). The Motor Runs Quietly And Doesn't Cause The Generator To Become Too Hot Over A Long Time..
【Stable Output 24V Dc Power Supply】Over-Current, Over-Voltage And Overload Protection, Power Supply Stable Power Supply, Electrical Energy Conversion Rate Of Up To 90%, Higher Efficiency. Together With The Heat Dissipation Fan Design, Shell Hollow Design, Heat Dissipation Ability Faster And Stronger, More Durable Performance..
【Usb Interface, Drive-Free Design 4-Axis Linkage Control Card】Output Pulse Frequency Of 100Khz, Using The Minimum Error Interpolation Algorithm, High Processing Accuracy. Supports Up To 4 Axes Of Linkage Control, Of Which The 4Th Axis Can Be Set As The Slave Axis. The Control Card Can Be Connected To Pc-Compatible Computers Such As Laptops, Desktops, Tablets And Other Computers With A Usb Interface. As Long As Mach3 Is Running, The Control Card Can Be Used Without Installing Any Drivers..
【Multi-Function Control Card】General-Purpose Opto-Couplers Isolation Input : Can Support The Limit Switch, Emergency Stop Switch, Auto Tool Zero, Home Switch And Electronic Handwheel; Have 0-10V Signal Output , You Can Use Mach3 Software To Control The Spindle Motor Speed; 4 General-Purpose Isolated Relay Drive Output Interface, Can Drive Four Relays For Controlling The Spindle Starts, Forward Rotating And Reverse Rotating, Pumps Or Other Device..
【Upgraded 4.5A Stepper Motor Driver】Using The Latest Tb6600 New Installation Chip, There Are Low-Voltage Shutdown, Thermal Over-Stop And Over-Current Circuit Protection, And Compared With The Tb6560 Increased Short-Circuit Protection. Tb6600 Driver Operating Voltage Of Dc 10-45Vdc, Support For Sub-Division Of The Whole Step, Half-Step, 1/4, 1/8, 1/16 Step, Up To 42/57/86 Two-Phase / Four-Phase / Four-Wire / Six-Wire Stepper Motors Within 4.2A. / Six-Wire Stepper Motor..
【Control Card And Tb6600 Driver Wiring (X-Axis As An Example) 】Driver's "Clk-" Connects To Control Card's Xp Pin , Driver's "Cw-" Connects To Control Card's Xd Pin , Driver's "5V" Connects To Control Card's 5V Pin.(The Usb Mach3 Control Card Can't Support Connection En- And En+)..
Features
- Motor and TB6600 Driver wiring Stepper motor's RED wire connects to driver's A+ port. Stepper motor's GREEN wire connects to driver's A- port. Stepper motor's YELLOW wire connects to driver's B+ port. Stepper motor's BLUE wire connects to driver's B- port.
- Control Card and TB6600 Driver wiring (X-axis as an example) Driver's CLK- connects to control card's XP pin , Driver's CW- connects to control card's XD pin , Driver's 5V connects to control card's 5V pin.(The USB Mach3 control card can't support connection EN- and EN+).
- Low Noise/High Torque Hybrid Stepper Motor 23HS8430B 2-phase stepper motor with dual shaft diameter of 8mm, a current of 3A and an angle of 1.8 , is made of durable metal on the outside, and the perfect combination of rubber and rotor fills up the inner space and stabilizes the overall structure of the motor. The coils are made of pure copper enameled wire and the torque is up to 270oz-in (180N.cm/18kg-cm). The motor runs quietly and doesn't cause the generator to become too hot over a long time.
- Upgraded 4.5A Stepper Motor Driver Using the latest TB6600 new installation chip, there are low-voltage shutdown, thermal over-stop and over-current circuit protection, and compared with the TB6560 increased short-circuit protection. TB6600 driver operating voltage of DC 10-45VDC, support for sub-division of the whole step, half-step, 1/4, 1/8, 1/16 step, up to 42/57/86 two-phase / four-phase / four-wire / six-wire stepper motors within 4.2A. / six-wire stepper motor.
- USB Interface, Drive-free Design 4-Axis Linkage Control Card Output pulse frequency of 100KHz, using the minimum error interpolation algorithm, high processing accuracy. Supports up to 4 axes of linkage control, of which the 4th axis can be set as the slave axis. The control card can be connected to PC-compatible computers such as laptops, desktops, tablets and other computers with a USB interface. As long as Mach3 is running, the control card can be used without installing any drivers.
- Multi-function control card General-purpose opto-couplers isolation input : can support the limit switch, emergency stop switch, auto tool zero, home switch and electronic handwheel; Have 0-10V signal output , you can use mach3 software to control the spindle motor speed; 4 general-purpose isolated relay drive output interface, can drive four relays for controlling the spindle starts, forward rotating and reverse rotating, pumps or other device.
- Stable output 24V DC power supply Over-current, over-voltage and overload protection, power supply stable power supply, electrical energy conversion rate of up to 90%, higher efficiency. Together with the heat dissipation fan design, shell hollow design, heat dissipation ability faster and stronger, more durable performance.
- See more on Amazon...
Brand: RATTMMOTOR | Manufacturer: RTM
See On Amazon Similar To RATTMMOTOR 4 Axis CNC Controller
#1
6 Axis 125KHz NVCM USB Mach3 Stepper Motor Motion Control Card Breakout Board USB interface CNC Controller Board 12-32VDC for Servo Motor
Asin: B07C5KH4HB | Model: NVCM | PartNumber: NVCM | Ean: 0785004502919 | UPC: 785004502919
♞【Max 6 Axis Control】Can Support 6 Axis Stepper Systems Maxisim,125Khz Pulse Output For Every Axis.
♞【Multifunction】 Power Supply Interface, Usb Connection Interface, Stepper/Servo Control Output Interface, Spindle Control Output Interface, Estop And Limited Switch And Tool Setting Input Interface And So On..
♞【Pwm Output】1 Port 0-10V Spindle Speed Analog Output Interface(Can Change To Pwm Output);.
♞【Dc Power Supply Input】Main Device Is 24V-32V Dc Power Supply Input,Current Should Higher Than 1A;.
Features
- Support software This NVCM card support Mach3 software, through USB port to communicate with computer.
- DC power supply input main device is 24V-32V DC power supply input,current should higher than 1A;
- Max 6 Axis Control Can support 6 axis stepper systems maxisim,125KHz pulse output for every axis
- PWM output 1 port 0-10V spindle speed analog output interface(can change to PWM output);
- Multifunction Power supply interface, USB connection interface, Stepper/Servo control output interface, spindle control output interface, Estop and limited switch and tool setting input interface and so on.
- See more on Amazon...
Brand: CNCTOPBAOS | Manufacturer: Changzhou Rattm Motor Co.,Ltd
See On Amazon #2
DIY CNC Controller Card, USB 4-Axis Linkage Mach3 Stepper Motor Motion Control Card, 100Khz Motion Controller Card Breakout Board for CNC Engraving
Asin: B07XH1ZPJN | Model: Wendry1pdn5v4zgq | PartNumber: Wendry1pdn5v4zgq | Ean: 0748904873558 | UPC: 748904873558
Support Emergency Input.
Support For Connecting Electronic Hand Wheel.
Support For Limit Switch.
Support Automatic Probe Tool.
Features
- Maximum step-pulse frequency is 100KHz, which is suitable for the servo or stepping motor
- Support automatic probe tool
- Support emergency input
- Support for limit switch
- Support for connecting electronic hand wheel
- See more on Amazon...
Brand: Wendry | Manufacturer: Wendry
Dimensions: 1.18 x 7.09 x 5.91 inches
See On Amazon #3
RATTMMOTOR 3018 PRO MAX CNC Wood Router Machine Kit 3 Axis GRBL Control DIY Mini CNC Engraver Carving Milling Machine+Offline Controller+775 Spindle Motor ER11 for Cutting Acrylic PVC PCB Plastic Wood
Asin: B08JYWH4K5 | Model: 3018Pro-M | PartNumber: 3018Pro-M | Ean: 0619191686032 | UPC: 619191686032
【Applicable Engraving Material】Cnc 3018 Pro Max Machine Can Not Only Engraving Wood/Plastic/Acrylic/ Pvc/Pcb/Carbon Fiber/Density Board And So On, But Also Soft Metal Like Copper, Aluminum And The Similar Materials. Howerever, Harder Materials Cannot Be Engraved Such As Glass, Hard Metal, Jade, Ect..
【Cnc Offline Controller】This Machine Can Be Controlled Simply By The Offline Controller Without Connecting It To A Computer. Support Sd Card And Tf Card At The Same Time, Standard Capacity 1G. After Inserting The File Into The Sd Card,The Engraving File Can Be Directly Identified..
【Update Grbl1.1 Control Board】 ①The Grbl Board Supports Emergency Stop And X/Y/Z Axis Limit Functions, Which Can Be Used Together With The Emergency Stop Button And Limit Switch On The Engraving Machine To Ensure A Safe And Simple Working Environment. ②Other Functions And Features Such As: Maximum Support For 20000Rpm Spindle, Tool Setting(Probe) , Offline Controller, With A Power Switch Button And A Silent Fan Cooling..
【Simple Assembly/Use】This Mini Cnc Router Machine Kit Is Mainly Designed For Diy Carving Enthusiasts/Beginners, Easily Assembled And Opertated, Coming With A Paper Manual And Usb Flash Drive Of All The Files..
Features
- Upgrade Version CNC 3018 PRO MAX Frame size: 42x35x27CM (16.53 x 13.78 x 10.63 ). Working area:18x10x4.5CM(11.8 x 7.1 x 1.8 ). Material: Aluminum Alloy. Spindle: 775 spindle motor (12-24V) 24V:10000r/min. Stepper motor: 42 stepper motor, 12V, phase current 1.3A, phase resistance 2.1 ohms, torque 0.25N.m
- Simple Assembly/Use This mini cnc router machine kit is mainly designed for DIY carving enthusiasts/beginners, easily assembled and opertated, coming with a paper manual and USB flash drive of all the files.
- Applicable Engraving Material CNC 3018 PRO MAX machine can not only engraving wood/plastic/acrylic/ pvc/pcb/carbon fiber/density board and so on, but also soft metal like copper, aluminum and the similar materials. Howerever, harder materials cannot be engraved such as glass, hard metal, jade, ect.
- Update GRBL1.1 Control Board The GRBL board supports emergency stop and X/Y/Z axis limit functions, which can be used together with the emergency stop button and limit switch on the engraving machine to ensure a safe and simple working environment. Other functions and features such as: maximum support for 20000RPM spindle, tool setting(probe) , offline controller, with a power switch button and a silent fan cooling.
- CNC Offline Controller This machine can be controlled simply by the offline controller without connecting it to a computer. Support SD card and TF card at the same time, standard capacity 1G. After inserting the file into the SD card,the engraving file can be directly identified.
- See more on Amazon...
Brand: RATTMMOTOR | Manufacturer: RTM
See On Amazon #4
CNCTOPBAOS 3 Axis GRBL 1.1f USB Port CNC Engraving Machine Control Board CNC Router Engraver Milling Machine Controller Board
Asin: B07B3RFNJ7 | Model: 4V | PartNumber: 4V | Ean: 0785004502766 | UPC: 785004502766
♞【Support Motor】Support Xyz Three-Axis Control, Spindle.Support Stepper Motor: 12V, Maximum Current Of 2A Or Less Is Recommended Within 1.5A And Additional Heat. (Any Stepper Motor Nema17,Nema23);Support Spindle: Support 24Vdc Spindle Pwm Speed (0%-100%),Also Support 3-Pin Pwm/Ttl Signal Control Module.
♞【Applications】 The Control Board Can Be Used With The 1310,1610-Pro, 3018,3018-Pro And 3018-Pro Max Etc Engraving Machines..
♞【New Functions】Add 2-Pin Emergency Stop Button Port,Probe Port,Xyz Limit Port And Add The Power Button Switch..
♞【Support Software】Grbl Contol/Candle(3 Axis)/Universal Gcode Sender; Support System: Windows Xp/7/8/10.
Features
- Model Upgraded 3 Axis GRBL 1.1F USB Port GRBL Control Board; Input voltage: 24VDC
- Support software GRBL Contol/Candle(3 axis)/Universal Gcode Sender; Support System: Windows XP/7/8/10
- Support Motor Support XYZ three-axis control, spindle.Support stepper motor: 12V, maximum current of 2A or less is recommended within 1.5A and additional heat. (Any stepper motor Nema17,Nema23);Support spindle: Support 24VDC Spindle PWM speed (0%-100%),also support 3-pin PWM/TTL signal control module
- New functions Add 2-pin emergency stop button port,probe port,XYZ limit port and add the power button switch.
- Applications The control board can be used with the 1310,1610-PRO, 3018,3018-PRO and 3018-PRO MAX etc engraving machines.
- See more on Amazon...
Brand: CNCTOPBAOS | Manufacturer: Changzhou Rattm Motor Co.,Ltd
Weight: 0.15 Kilograms
See On Amazon #5
RATTMMOTOR 4 Axis CNC USB Mach3 Controller Breakout Board CNC Motion Controller Card Stepper Motor Driver with Cable for CNC Router Engraving Machine, Servo Motor, Stepper Motor
Asin: B07ZT7RGY9 | Ean: 0769135849686 | UPC: 769135849686
Signal Output:0-10V, It Can Control The Spindle Motor Speed Through Using Mach3 Software..
Recommends That Users Install The Emergency Stop Button And Make Sure The Button Is Functioning Properly..
If You Are Not Familiar With The Product And Software Features, Make Sure The Machine's Power Switch On Hand, You Can Quickly Turn Off The Power..
This Usb Motion Card Does Not Need Install Any Usb Driver, Windows2000/Xp/Windows7,Can Directly Identify (Notice: Doesn't Support Win8/Win10/Macos System !!!) ..
Features
- Model Name: Mach3 USB Motion Card; 4-axis linkage, Maximum step-pulse frequency: 100KHz, support connect four stepper motor drives or servo drives.
- This USB motion card does not need install any USB driver, Windows2000/XP/Windows7,can directly identify (Notice: Doesn't support Win8/win10/macOS system !!!) .
- Signal Output:0-10V, it can control the spindle motor speed through using mach3 software.
- If you are not familiar with the product and software features, make sure the machine's power switch on hand, you can quickly turn off the power.
- Recommends that users install the emergency stop button and make sure the button is functioning properly.
- See more on Amazon...
Brand: RATTMMOTOR | Manufacturer: JingDiao
See On Amazon #6
CNCTOPBAOS 3 Axis GRBL Offline Controller Board Remote Hand Control LCD Screen Off-line Control Module for 1610 3018 PRO CNC Router Carving Milling Engraving Machine Offline CNC Controller
Asin: B087BZBZB2 | Model: OFGR | PartNumber: OFGR | Ean: 0681385631425 | UPC: 681385631425
♞【Support Sd&Tf Card】Support Sd Card And Tf Card At The Same Time,Standard Capacity 1G..
【Easy To Use & Wide Application】All You Have To Do Is Connect The Offline Module To The Grbl Controller Board, Which You Can Use It To Control The Cnc Rounter; It Supports Our 1310, 1610, 3018, 3018 Pro ,Upgraded 3018 Pro Etc Grbl Control Cnc Machine..
♞【Feature】With This Offline Controller Module, You Can Directly Control The Cnc Router Without Connecting It To Your Computer. After Inserting The File Into The Sd Card,The Engraving File Can Be Directly Identified. You Can Also Use The Micro Usb Cable To Connect The Offline Hand Controller Board To Your Computer And Save The File Directly..
♞【Package Include】1Pcs Offline Hand Controller Board+1Pcs Cable+1Pcs Sd Card.
Features
- Product 3 Axis GRBL Offline Controller Hand Control
- Package include 1Pcs offline hand controller board+1Pcs cable+1Pcs SD Card
- Support SD&TF card Support SD card and TF card at the same time,standard capacity 1G.
- Feature With this offline controller module, you can directly control the CNC router without connecting it to your computer. After inserting the file into the SD card,the engraving file can be directly identified. You can also use the micro USB cable to connect the offline hand controller board to your computer and save the file directly.
- Easy to use & Wide application All you have to do is connect the offline module to the GRBL controller board, which you can use it to control the CNC rounter; It supports our 1310, 1610, 3018, 3018 pro ,upgraded 3018 pro etc grbl control cnc machine.
- See more on Amazon...
Brand: CNCTOPBAOS | Manufacturer: Changzhou Rattm Motor Co.,Ltd
See On Amazon #7
RATTMMOTOR CBX1605 400mm / 15.75" Linear Stage Actuator with Square Linear Slide Rail and 1605 Ballscrew Motorized XY XYZ Linear Stage Table CNC Linear Motion Rail Guide+Nema23 Stepper Motor for CNC
Asin: B078CYDBST | Model: CBX1605-400A | PartNumber: CBX1605-400A | Ean: 0654615632677 | UPC: 654615632677
【1605 Ball Screw】- Drive Type: Cbx1605 Ball Screw. Effective Travel Length: 400Mm. Screw Precision Grade: C7. Screw Pitch: 5Mm. Flange Nut Screw Rod With Precision Up To 0.003Mm..
【Main Application】- The Important Hardware Equipment That Constitutes Industrialized Machinery Can Accurately Control The Accuracy And Speed Of The Moving Parts Of Mechanical Equipment. It Is Suitable For Cnc Machine, Placement Equipment, Laser Cutting Equipment, Spraying Equipment, Medical Equipment, Battery Equipment And Other Industrial Automation Fields..
【Slide Block】- Length: 60Mm. M4 Sliding Nut Design On The Side, Limit Switch Can Be Installed At Any Position. The Slider Is Made Of 6030 Aluminum And Are Oxidized, Which Is Beautiful And Generous..
【Nema23 Stepper Motor】- Motor Length: 56Mm. Motor Flange Size: 57Mm. Holding Torque: 1.2N.M. Phase: 2. Current: 3A. Resistance: 0.8 Ω. Inductance: 2.4Mh. Rotor Inertia: 440G.Cm. Wiring: Red(A+), Green(A-), Yellow(B+), Blue(B-)..
Features
- Product Structure Analysis - Nema23 Stepper Motor+Stepper Motor Connecting Piece+Coupling+1605 Ball Scew+Slide Block+Sliding Table +Bearing Piece+Base.
- Nema23 Stepper Motor - Motor length: 56mm. Motor flange size: 57mm. Holding torque: 1.2N.m. Phase: 2. Current: 3A. Resistance: 0.8 . Inductance: 2.4mH. Rotor Inertia: 440g.cm. Wiring: Red(A+), Green(A-), Yellow(B+), Blue(B-).
- 1605 Ball Screw - Drive type: CBX1605 ball screw. Effective travel length: 400mm. Screw precision grade: C7. Screw Pitch: 5mm. Flange nut screw rod with precision up to 0.003mm.
- Slide Block - Length: 60mm. M4 sliding nut design on the side, limit switch can be installed at any position. The slider is made of 6030 aluminum and are oxidized, which is beautiful and generous.
- Main Application - The important hardware equipment that constitutes industrialized machinery can accurately control the accuracy and speed of the moving parts of mechanical equipment. It is suitable for CNC machine, placement equipment, laser cutting equipment, spraying equipment, medical equipment, battery equipment and other industrial automation fields.
- See more on Amazon...
Brand: RATTMMOTOR | Manufacturer: Rattmmotor company
Weight: 5.84 pounds
See On Amazon #8
ARM 32-bit 4 Axis GRBL 1.1f Type-C Port CNC Engraving Machine Control Board,Optocoupler Isolation,CNC Router Engraver Milling Machine GRBL Control
Asin: B09SZDTBHS | Model: 4A | PartNumber: 4A
Tri-Axis Software Support:Candle/Lasergrbl/Lightburn/Usg. Quad-Axis Software Support:Window/Linux/Mac.
Use Type-C Usb Interface, More Convenient To Use And More Stable Data Transmission.
Support External Driver, External Driver Reserved Interface With The Market High-Power Driver Consistent, Convenient Wiring.
Supply Voltage：Dc24v- 5A.Reserved 24V, 12V, 5V Power Output Port, Convenient To Expand Various Functions.
Features
- 4-Axis 3.0,GRBL 1.1f control board
- Supply Voltage DC24V- 5A.Reserved 24V, 12V, 5V power output port, convenient to expand various functions
- Tri-axis software support:Candle/LaserGRBL/LightBurn/USG. Quad-axis software support:Window/Linux/Mac
- Support external driver, external driver reserved interface with the market high-power driver consistent, convenient wiring
- Use Type-C USB interface, more convenient to use and more stable data transmission
- See more on Amazon...
Brand: ANNOY TOOLS | Manufacturer: ANNOY TOOLS
See On Amazon #9
RATTMMOTOR CNC Controller Kit, 4 Axis CNC Kit with Nema23 Stepper Motor 57*76mm 270Oz-in 3A 1.8Nm, TB6600 Driver 4A, USB Mach3 CNC Motion Control Card Breakout Board, 24V Power Supply for CNC Machine
Asin: B09MRXXZZR | Model: 4 axis | PartNumber: 4 axis | Ean: 0754193834842 | UPC: 754193834842
【Low Noise/High Torque Hybrid Stepper Motor】23Hs8430 2-Phase Stepper Motor With A Shaft Diameter Of 8Mm, A Current Of 3A And An Angle Of 1.8°, Is Made Of Durable Metal On The Outside, And The Perfect Combination Of Rubber And Rotor Fills Up The Inner Space And Stabilizes The Overall Structure Of The Motor. The Coils Are Made Of Pure Copper Enameled Wire And The Torque Is Up To 270Oz-In (180N.Cm/18Kg-Cm). The Motor Runs Quietly And Doesn't Cause The Generator To Become Too Hot Over A Long Time..
【Stable Output 24V Dc Power Supply】Over-Current, Over-Voltage And Overload Protection, Power Supply Stable Power Supply, Electrical Energy Conversion Rate Of Up To 90%, Higher Efficiency. Together With The Heat Dissipation Fan Design, Shell Hollow Design, Heat Dissipation Ability Faster And Stronger, More Durable Performance..
【Usb Interface, Drive-Free Design 4-Axis Linkage Control Card】Output Pulse Frequency Of 100Khz, Using The Minimum Error Interpolation Algorithm, High Processing Accuracy. Supports Up To 4 Axes Of Linkage Control, Of Which The 4Th Axis Can Be Set As The Slave Axis. The Control Card Can Be Connected To Pc-Compatible Computers Such As Laptops, Desktops, Tablets And Other Computers With A Usb Interface. As Long As Mach3 Is Running, The Control Card Can Be Used Without Installing Any Drivers..
【Multi-Function Control Card】General-Purpose Opto-Couplers Isolation Input : Can Support The Limit Switch, Emergency Stop Switch, Auto Tool Zero, Home Switch Etc, Electronic Handwheel; Have 0-10V Signal Output , You Can Use Mach3 Software To Control The Spindle Motor Speed; 4 General-Purpose Isolated Relay Drive Output Interface, Can Drive Four Relays For Controlling The Spindle Starts, Forward Rotating And Reverse Rotating, Pumps Or Other Device..
【Support Forward And Reverse Control Stepper Motor Driver】42/57 Tb6600 Stepper Motor Driver With Input Voltage Anti-Reverse Connection And Overheat/Overcurrent Short Circuit Protection, Equipped With Red Warning Light. Through The 3-Digit Dip Switch, You Can Choose 7 Subdivisions (1, 2 / A, 2 / B, 4, 8, 16, 32) And 8 Subdivisions (0.5A, 1.0A 1.5A, 2.0A, 2.5A, 3.0A, 3.5A) Current Control..
【Control Card And Tb6600 Driver Wiring (X-Axis As An Example) 】Driver's "Pul+" Connects To Control Card's Xp+ Pin , Driver's "Dir+" Connects To Control Card's Xd+ Pin , Driver's " Pul- " Pin And " Dir- " Connection To Usb Mach3 Control Card's " 5V ""..
Features
- Motor and TB6600 Driver wiring Stepper motor's RED wire connects to driver's A+ port. Stepper motor's GREEN wire connects to driver's A- port. Stepper motor's YELLOW wire connects to driver's B+ port. Stepper motor's BLUE wire connects to driver's B- port.
- Control Card and TB6600 Driver wiring (X-axis as an example) Driver's Pul+ connects to control card's XP+ pin , Driver's DIR+ connects to control card's XD+ pin , Driver's PUL- pin and DIR- connection to USB Mach3 control card's 5V .
- Low Noise/High Torque Hybrid Stepper Motor 23HS8430 2-phase stepper motor with a shaft diameter of 8mm, a current of 3A and an angle of 1.8 , is made of durable metal on the outside, and the perfect combination of rubber and rotor fills up the inner space and stabilizes the overall structure of the motor. The coils are made of pure copper enameled wire and the torque is up to 270oz-in (180N.cm/18kg-cm). The motor runs quietly and doesn't cause the generator to become too hot over a long time.
- Support Forward and Reverse Control Stepper Motor Driver 42/57 TB6600 stepper motor driver with input voltage anti-reverse connection and overheat/overcurrent short circuit protection, equipped with red warning light. through the 3-digit DIP switch, you can choose 7 subdivisions (1, 2 / A, 2 / B, 4, 8, 16, 32) and 8 subdivisions (0.5A, 1.0A 1.5A, 2.0A, 2.5A, 3.0A, 3.5A) current control.
- USB Interface, Drive-free Design 4-Axis Linkage Control Card Output pulse frequency of 100KHz, using the minimum error interpolation algorithm, high processing accuracy. Supports up to 4 axes of linkage control, of which the 4th axis can be set as the slave axis. The control card can be connected to PC-compatible computers such as laptops, desktops, tablets and other computers with a USB interface. As long as Mach3 is running, the control card can be used without installing any drivers.
- Multi-function control card General-purpose opto-couplers isolation input : can support the limit switch, emergency stop switch, auto tool zero, home switch etc, electronic handwheel; Have 0-10V signal output , you can use mach3 software to control the spindle motor speed; 4 general-purpose isolated relay drive output interface, can drive four relays for controlling the spindle starts, forward rotating and reverse rotating, pumps or other device.
- Stable output 24V DC power supply Over-current, over-voltage and overload protection, power supply stable power supply, electrical energy conversion rate of up to 90%, higher efficiency. Together with the heat dissipation fan design, shell hollow design, heat dissipation ability faster and stronger, more durable performance.
- See more on Amazon...
Brand: RATTMMOTOR | Manufacturer: RTM
Dimensions: 1.93 x 8.46 x 4.49 inches
See On Amazon #10
RATTMMOTOR 100mm Travel Length Linear Stage Acuator Z axis Sliding Table DIY Milling Linear Motion Guide Rail Suitable for Woodworking CNC Engraving Machine
Asin: B09KRJK961 | Model: RTM-100 | PartNumber: RTM-100
【Applicable Situation】: The Linear Platform Actuator Is Suitable For Woodworking And Cnc Engraving Machines. This Module Can Also Be Installed Onto A Two-Axes Machine And Turn Into A Three-Axes Machine..
【Easy To Install】: This Linear Motion Rail Mounting Hole Is Carefully Designed, It Can Be Adjusted, Easy To Install On Other Devices. Its Stroke Is 100Mm, Easy To Use, Smooth Running, Fast Speed, Low Noise..
【Clamping Tool】: The Slider Can Be Mounted, Laser Head, Engraving Knife Or Other Equipment.
【Work Performance】: The Linear Uses A New Stepper Motor, 2 Phase 4 Wire. Mounting This Z-Axes Slid Module Can Turn Engraving Machine Into Notes Plotter Or 3-Axes Cnc Engraving Machine..
Features
- Mechanical Accessories : This linear platform actuator constitutes an important hardware device for industrial machinery, which can accurately control the accuracy and speed of mechanical equipment moving parts.
- Work performance : The linear uses a new stepper motor, 2 phase 4 wire. Mounting this Z-axes slid module can turn engraving machine into notes plotter or 3-axes CNC engraving machine.
- Applicable situation : The linear platform actuator is suitable for woodworking and CNC engraving machines. This module can also be installed onto a two-axes machine and turn into a three-axes machine.
- Clamping tool : The slider can be mounted, laser head, engraving knife or other equipment
- Easy to install : This linear motion rail mounting hole is carefully designed, it can be adjusted, easy to install on other devices. Its stroke is 100mm, easy to use, smooth running, fast speed, low noise.
- See more on Amazon...
Brand: RATTMMOTOR | Manufacturer: RTM
See On Amazon #11
RATTMMOTOR Normally Open Mach3 CNC Automatic Tool Sensor Gauge Changer CNC Z Axis Probe Tool Touch Sensor Setter Setting 4 Wires for CNC Router Engraver Machine
Asin: B08LK93NTC | Model: H:65 | PartNumber: H:65 | Ean: 0619191755172 | UPC: 619191755172
【Material】The Housing Material Of This Tool Setter Is Made Of 4S Grinding Grade Material. The Bottom Magnet Design Can Be Directly Connected To The Machine And Firmly Adsorbed To The Body. The Contact Material Is Made Of Super Hard Alloy, The Design Is Exquisite And The Installation Is Simple..
【Feature-2】The Tool Setter Will Send Out An Alarm Signal In Time When It Is Over-Travel To Avoid Other Troubles Caused By Equipment Operation. Moreover, The Tool Setter Has Strong Anti-Interference. The Protruding Sharp Corner Of The Tool Directly Touches The Tool Tip Related To The Machining Size, Detects Its Value And Size, And Outputs The Signal. It Has Higher Accuracy Than The Average Value Obtained By Converting The Amount Of Light And Electricity..
【Feature-1】This Tool Setting Instrument Is Designed With Dustproof And Waterproof Structure, Which Can Still Have Strong Durability Under The Condition Of Coolant And Iron Filings. It Does Not Need A Built-In Amplifier And Will Not Be Caused Deviations By The Location Temperature And Power Supply Voltage Fluctuations Of The Tool Setting Instrument, Which Can Be Directly Input To The Nc Program..
【Parameter】This Is A Normally Open 4-Wire High-Precision Tool Setting Instrument With A Stroke Of 5Mm. The Positioning Accuracy Is 0.001Mm, The Contact Life Is Up To 3 Million Times, The Contact Force Is 1.5N, And The Contact Rating: Dc24v 20Ma..
Features
- Description The tool setting instrument is a special tool setting instrument for the engraving machine machining center machine. The output signal of the tool setting instrument is received by the numerical control system and then the tool length setting, tool wear detection and tool breakage are detected by the program control. In the case of no vibration and malfunction, the thermal deformation of the machine can be corrected according to the rated voltage and current and the specified speed.
- Parameter This is a normally open 4-wire high-precision tool setting instrument with a stroke of 5mm. The positioning accuracy is 0.001mm, the contact life is up to 3 million times, the contact force is 1.5N, and the contact rating: DC24V 20mA.
- Material The housing material of this tool setter is made of 4S grinding grade material. The bottom magnet design can be directly connected to the machine and firmly adsorbed to the body. The contact material is made of super hard alloy, the design is exquisite and the installation is simple.
- Feature-1 This tool setting instrument is designed with dustproof and waterproof structure, which can still have strong durability under the condition of coolant and iron filings. It does not need a built-in amplifier and will not be caused deviations by the location temperature and power supply voltage fluctuations of the tool setting instrument, which can be directly input to the NC program.
- Feature-2 The tool setter will send out an alarm signal in time when it is over-travel to avoid other troubles caused by equipment operation. Moreover, the tool setter has strong anti-interference. The protruding sharp corner of the tool directly touches the tool tip related to the machining size, detects its value and size, and outputs the signal. It has higher accuracy than the average value obtained by converting the amount of light and electricity.
- See more on Amazon...
Brand: RATTMMOTOR | Manufacturer: RTM
Dimensions: 4.33 x 5.91 x 2.76 inches | Weight: 0.99 pounds
See On Amazon #12
CNCTOPBAOS 4 Axis USB Mach3 Handwheel Controller Remote Hand Control CNC Handwheel Manual Pulse Generator for CNC Router Lathe Engraving Milling Machine (WHB04B-4)
Asin: B07JN4P3YH | Model: PLCHANDWHEEL | PartNumber: PLCHANDWHEEL | Ean: 0681385631036 | UPC: 681385631036
♞【Advantages】Axis Select Band Switch To Achieve The Electronic Hand Wheel Off And The Corresponding X Y Z A B C Each Axis Function Of The Choice Of Control. The Choice Of The Step Distance Value Is Realized By Selecting The Switching Value Band, Which Is Simple And Convenient..
♞【Application】For Windows: All Mach3 Cnc System,Milling Machine,Carving Machine,Wood Machine And So On. Axis Select Band Switch To Achieve The Electronic Hand Wheel Off And The Corresponding X Y Z A B C Each Axis Function Of The Choice Of Control. The Choice Of The Step Distance Value Is Realized By Selecting The Switching Value Band, Which Is Simple And Convenient..
♞【Lcd Display】Display X Y Z A Axis Of The Mechanical Coordinates And Workpiece Coordinates. Show The Spindle Speed, The Value Of The Feed Rate. Dot Matrix Lcd With Backlight. Axis Selection, Power Band Switch Control..
♞【Technology】100Ppr Manual Pulse Generator Support 10 Macro Function Button..
Features
- Product 4 Axis USB Mach3 Handwheel ; Model: WHB04B-4
- Technology 100PPR manual pulse generator support 10 macro function button.
- Advantages Axis select band switch to achieve the electronic hand wheel off and the corresponding X Y Z A B C each axis function of the choice of control. The choice of the step distance value is realized by selecting the switching value band, which is simple and convenient.
- LCD display Display X Y Z A axis of the mechanical coordinates and workpiece coordinates. Show the spindle speed, the value of the feed rate. Dot matrix LCD with backlight. Axis selection, power band switch control.
- Application For Windows: All Mach3 CNC system,milling machine,carving machine,wood machine and so on. Axis select band switch to achieve the electronic hand wheel off and the corresponding X Y Z A B C each axis function of the choice of control. The choice of the step distance value is realized by selecting the switching value band, which is simple and convenient.
- See more on Amazon...
Brand: CNCTOPBAOS | Manufacturer: Changzhou Rattm Motor Co.,Ltd
Weight: 0.68 Kilograms
See On Amazon #13
RATTMMOTOR CNC GRBL Offline Controller, 3 Axis GRBL DIY CNC Router Offline Control Button/Module LCD Screen for Mini CNC Carving Milling Engraver Machine
Asin: B07TB6HZY4 | Ean: 0769135311664, 0769135849662 | UPC: 769135849662, 769135311664
With This Offline Controller Module, You Can Directly Control The Cnc Router Without Connecting It To Your Computer..
Easy To Use: All You Have To Do Is Connect The Offline Module To The Grbl Controller Board, Which You Can Use It To Control The Cnc Router Machine..
After Inserting The File Into The Sd Card,The Engraving File Can Be Directly Identified. You Can Also Use The Micro Usb Cable To Connect The Offline Hand Controller Board To Your Computer And Save The File Directly..
Support Sd Card And Tf Card At The Same Time, Standard Capacity 1G..
Features
- The injection molded case is beautiful and formal; the integral button and the key cap are not easy to fall off.
- Support SD card and TF card at the same time, standard capacity 1G.
- With this offline controller module, you can directly control the CNC router without connecting it to your computer.
- After inserting the file into the SD card,the engraving file can be directly identified. You can also use the micro USB cable to connect the offline hand controller board to your computer and save the file directly.
- Easy to use: All you have to do is connect the offline module to the GRBL controller board, which you can use it to control the CNC router machine.
- See more on Amazon...
Brand: RATTMMOTOR | Manufacturer: RTM
Weight: 0.20 Kilograms
See On Amazon #14
RATTMMOTOR CNC Digital Stepper Driver, 4-Axis Stepper Motor Driver NV5160T4 Pulse/Direction Controller 12-48VDC Max 6A 256 Micro-Step Resolutions for Nema 23, 24 and Nema 34 Stepper Motor
Asin: B0BW3V8QCZ | Model: NV5160T4 | PartNumber: NV5160T4 | Ean: 0754193412019 | UPC: 754193412019
【Performance Features②】Nv5160t4 Driver Has Adjustable Quiescent Current, Up To 256 Adjustable Subdivisions, Pulse Response Frequency Up To 1Mhz, With Input Signal Opto-Isolation, H-Bridge Bipolar Constant Current Drive And Other Features..
【8 Selectable Micro-Step Resolutions】The Optional Values Of Micro-Step Resolutions Are 2, 4, 8, 16, 32, 64, 128, 256..
【Driver (Parameter) Setting] Nv5160t4 Relies On The Screen And 4 Keys To Configure Parameters, Configurable Parameters Include Motion Current, Quiescent Current And Subdivision..
【Current Parameter Setting】The Optional Values Of Current Parameter Are 0.5A, 1A, 1.5A, 2A, 2.5A, 3A, 3.5A, 4A, 4.5A, 5A, 5.5A, 6A..
【Driver Interface】The Driver Interface Contains Five Groups Of Interfaces, Including Power Supply Interface, Stepper Motor Interface, Pulse Control Interface, Input And Output Interface, And Bus Interface..
【Performance Features ①】Nv5160t4 Driver's Power Supply Voltage Is 12-48Vdc; High Current, Up To 6A, Can Drive 86 Motors (Need External Forced Heat Dissipation Can Reach 6A), 8-Speed Optional; With Automatic Over-Current And Over-Voltage Protection Function..
Features
- Product Overview The driver is a high-performance 4-axis stepper motor driver that supports pulse direction control. It has the advantages of strong anti-interference ability, good stability, low cost, etc. It also has the advantages of small size, low heat generation and high power.
- Performance features NV5160T4 driver's power supply voltage is 12-48VDC; high current, up to 6A, can drive 86 motors (need external forced heat dissipation can reach 6A), 8-speed optional; with automatic over-current and over-voltage protection function.
- Performance features NV5160T4 driver has adjustable quiescent current, up to 256 adjustable subdivisions, pulse response frequency up to 1MHz, with input signal opto-isolation, H-bridge bipolar constant current drive and other features.
- Driver interface The driver interface contains five groups of interfaces, including power supply interface, stepper motor interface, pulse control interface, input and output interface, and bus interface.
- Driver (parameter) setting] NV5160T4 relies on the screen and 4 keys to configure parameters, configurable parameters include motion current, quiescent current and subdivision.
- Current parameter setting The optional values of current parameter are 0.5A, 1A, 1.5A, 2A, 2.5A, 3A, 3.5A, 4A, 4.5A, 5A, 5.5A, 6A.
- 8 Selectable micro-step resolutions The optional values of micro-step resolutions are 2, 4, 8, 16, 32, 64, 128, 256.
- See more on Amazon...
Brand: RATTMMOTOR | Manufacturer: RTM
See On Amazon #15
RATTMMOTOR 3-Axis Update GRBL 1.1f CNC Controller with Emergency and Limit Switch Fuction, CNC Router Engraver Machine GRBL Controller Board with Fan Cooling for CNC Wood Router Machine
Asin: B089SM3VNQ | Ean: 0619191853823 | UPC: 619191853823
【Emergency Stop Function】 Added An Emergency Stop Button, During The Engraving Process, If The User Encounters An Emergency And Needs To Stop The Engraving Immediately, User Can Press The Button To Stop The Operation..
【Power Switch Button Function】Added The Power Switch Button, Simple Operation, More Safety In The Process Of Using The Machine..
【X/Y/Z Axis Limit Switch Function】Added X/Y/Z Axis Limit Switch, When The Engraving Machine Moves Up And Down Or Left And Right, It Will Stop Immediately If It Exceeds The Forming Range..
【Mutiple Functions】Maximum Support For 20000Rpm Spindle, Support 0.5W-20W Module, Support Tool Setting(Probe) , Support Grbl Offline Controller. Equipped With Silent Fan, Good Cooling Effect..
Features
- Basic Parameters Connection:USB (USB-CH340), Input voltage:12-24VDC (recommend 24VDC), Power Interface:5.5-2.5mm DC interface, Control software:GRBL control/ Lasrrgrbl, Support system:Windows XP / Win 7 / Win 8 / Win 10 (32/64 )/ Linux. Support Stepper motor:12V, maximum current of 2A or less,is recommended within 1.5A and additional heat (any nema17 or nema23 stepper motor). Spindle PWM speed: Support,
- Mutiple Functions Maximum support for 20000RPM spindle, Support 0.5W-20W module, Support tool setting(probe) , Support GRBL offline controller. Equipped with silent fan, good cooling effect.
- Emergency Stop Function Added an emergency stop button, during the engraving process, if the user encounters an emergency and needs to stop the engraving immediately, user can press the button to stop the operation.
- X/Y/Z axis Limit Switch Function Added X/Y/Z axis limit switch, when the engraving machine moves up and down or left and right, it will stop immediately if it exceeds the forming range.
- Power Switch Button Function Added the power switch button, simple operation, more safety in the process of using the machine.
- See more on Amazon...
Brand: RATTMMOTOR | Manufacturer: RTM
See On Amazon #16
RATTMMOTOR CNC 1610 PRO 3 Axis GRBL Control DIY Mini CNC Router Machine Kit with Offline Controller and 14pcs ER11 Collets CNC Engraving Milling Machine for Cutting Wood Plastic Acrylic PVC PCB
Asin: B09NRC2P2W | Model: 1610PRO-MJ | PartNumber: 1610PRO-MJ
【Applicable Engraving Material】Cnc 1610 Pro Machine Can Not Only Engraving Wood/Plastic/Acrylic/ Pvc/Pcb/Carbon Fiber/Density Board And So On, But Also Soft Metal Like Copper, Aluminum And The Similar Materials. Howerever, Harder Materials Cannot Be Engraved Such As Glass, Hard Metal, Jade, Ect..
【Cnc Offline Controller】This Machine Can Be Controlled Simply By The Offline Controller Without Connecting It To A Computer. Support Sd Card And Tf Card At The Same Time, Standard Capacity 1G. After Inserting The File Into The Sd Card,The Engraving File Can Be Directly Identified..
【Grbl Control Board/Software】This Machine Can Be Controlled By Grblcontrol/Candle Software After Connecting The Control Board To A Coumpter Via Usb Port. The Control Board Is Equipped With A Fan To Force Heat Dissipation, Also Has More Fuctions Such As Support Spindle Pwm Speed, Limit Switch, Tool Setting, Steering Gear..
【Simple Assembly/Use】This Mini Cnc Router Machine Kit Is Mainly Designed For Diy Carving Enthusiasts/Beginners, Easily Assembled And Opertated, Coming With A Paper Manual And Usb Flash Drive Of All The Files..
Features
- Upgrade Version CNC 1610 PRO Frame size: 30x26x25CM. Working area:18x10x4.5CM. Material: Aluminum Alloy. Spindle: 775 spindle motor (12-24V) 24V:10000r/min with14pcs ER11 collets . Stepper motor: 42 stepper motor, 12V, phase current 1.3A, phase resistance 2.1 ohms, torque 0.25N.m
- Simple Assembly/Use This mini cnc router machine kit is mainly designed for DIY carving enthusiasts/beginners, easily assembled and opertated, coming with a paper manual and USB flash drive of all the files.
- Applicable Engraving Material CNC 1610 PRO machine can not only engraving wood/plastic/acrylic/ pvc/pcb/carbon fiber/density board and so on, but also soft metal like copper, aluminum and the similar materials. Howerever, harder materials cannot be engraved such as glass, hard metal, jade, ect.
- GRBL Control Board/Software This machine can be controlled by Grblcontrol/Candle software after connecting the control board to a coumpter via USB port. The control board is equipped with a fan to force heat dissipation, also has more fuctions such as support spindle PWM speed, limit switch, tool setting, steering gear.
- CNC Offline Controller This machine can be controlled simply by the offline controller without connecting it to a computer. Support SD card and TF card at the same time, standard capacity 1G. After inserting the file into the SD card,the engraving file can be directly identified.
- See more on Amazon...
Brand: RATTMMOTOR | Manufacturer: RTM
Dimensions: 11.81 x 10.24 x 0.01 inches
See On Amazon #17
RATTMMOTOR 3018 Pro DIY CNC Router Kit+GRBL Offline Controller, 3 Axis Hobby CNC Router Machine, Plastic Acrylic PVC PCB Wood Mini Desktop Engraving Milling Carving Machine, Working Area 300x180x45mm
Asin: B08HRKWCXV | Model: 3018PRO-OL | PartNumber: 3018PRO-OL | Ean: 0619191721450 | UPC: 619191721450
✅【Applicable Engraving Material】Cnc 3018 Pro Machine Can Not Only Engraving Wood/Plastic/Acrylic/ Pvc/Pcb/Carbon Fiber/Density Board And So On, But Also Soft Metal Like Copper, Aluminum And The Similar Materials. Howerever, Harder Materials Cannot Be Engraved Such As Glass, Hard Metal, Jade, Ect..
✅【Cnc Offline Controller】This Machine Can Be Controlled Simply By The Offline Controller Without Connecting It To A Computer. Support Sd Card And Tf Card At The Same Time, Standard Capacity 1G. After Inserting The File Into The Sd Card,The Engraving File Can Be Directly Identified..
✅【Update Grbl1.1 Control Board】 ①The Grbl Board Supports Emergency Stop And X/Y/Z Axis Limit Functions, Which Can Be Used Together With The Emergency Stop Button And Limit Switch On The Engraving Machine To Ensure A Safe And Simple Working Environment. ②Other Functions And Features Such As: Maximum Support For 20000Rpm Spindle, Tool Setting(Probe) , Offline Controller, With A Power Switch Button And A Silent Fan Cooling..
✅【Simple Assembly/Use】This Mini Cnc Router Machine Kit Is Mainly Designed For Diy Carving Enthusiasts/Beginners, Easily Assembled And Opertated, Coming With A Paper Manual And Usb Flash Drive Of All The Files..
Features
- Upgrade Version CNC 3018 PRO Frame size: 42x35x27CM (16.53 x 13.78 x 10.63 ). Working area:18x10x4.5CM(11.8 x 7.1 x 1.8 ). Material: Aluminum Alloy. Spindle: 775 spindle motor (12-24V) 24V:10000r/min. Stepper motor: 42 stepper motor, 12V, phase current 1.3A, phase resistance 2.1 ohms, torque 0.25N.m
- Simple Assembly/Use This mini cnc router machine kit is mainly designed for DIY carving enthusiasts/beginners, easily assembled and opertated, coming with a paper manual and USB flash drive of all the files.
- Applicable Engraving Material CNC 3018 PRO machine can not only engraving wood/plastic/acrylic/ pvc/pcb/carbon fiber/density board and so on, but also soft metal like copper, aluminum and the similar materials. Howerever, harder materials cannot be engraved such as glass, hard metal, jade, ect.
- Update GRBL1.1 Control Board The GRBL board supports emergency stop and X/Y/Z axis limit functions, which can be used together with the emergency stop button and limit switch on the engraving machine to ensure a safe and simple working environment. Other functions and features such as: maximum support for 20000RPM spindle, tool setting(probe) , offline controller, with a power switch button and a silent fan cooling.
- CNC Offline Controller This machine can be controlled simply by the offline controller without connecting it to a computer. Support SD card and TF card at the same time, standard capacity 1G. After inserting the file into the SD card,the engraving file can be directly identified.
- See more on Amazon...
Brand: RATTMMOTOR | Manufacturer: RTM
See On Amazon #18
3 Axis GRBL 1.1f 32-Bit Controller-Control-Board Stepper Motor Support Offline Dual Y-axis USB Drive Board for Woodworking Engraving Machine, CNC Router, Laser Engraving Machine
Asin: B09YQ5BQJ1 | Model: 5.2 | PartNumber: 5.2
Usb Interface Communication, Support 3-Axis Engraving, Laser Module..
Nano 3Axis Control Board Is A 3 Axis Motion Control System Based On The Arduino Nano For Laser Engraving Machines, Drawer Machines, Cnc Engraving Machines, Etc..
⚠️To Protect Novice And Non-Professional Users, This Control Board Has Built-In Protection Programs That Prevent Firmware Modification. Please Confirm Whether The Board's Features Meet Your Requirements Before Purchasing..
Applicable Software: Grblcontrol (Candle), Lasergrbl And Other Software Supporting Grbl Firmware, Grbl Firmware Version 1.1F..
Dual Y-Axis, All-Round Use, Xyz Or Xyy..
Features
- Power supply: DC12-48V. spindle: 48V 0-500W.
- Dual y-axis, all-round use, XYZ or XYY.
- USB interface communication, support 3-axis engraving, laser module.
- Applicable software: Grblcontrol (Candle), LaserGRBL and other software supporting GRBL firmware, GRBL firmware version 1.1f.
- Nano 3Axis Control Board is a 3 Axis Motion control system based on the Arduino Nano for laser engraving machines, drawer machines, CNC engraving machines, etc.
- To protect novice and non-professional users, this control board has built-in protection programs that prevent firmware modification. Please confirm whether the board's features meet your requirements before purchasing.
- See more on Amazon...
Brand: ANNOY TOOLS | Manufacturer: ANNOY TOOLS
See On Amazon #19
CNCTOPBAOS 4 Axis Offline Stand Alone CNC Motion Controller System DDCSV3.1,Servo/Stepper Motor Control Replace Mach3 PLC+100PPR MPG Handwheel with E-Stop for CNC Router Engraving Machine
Asin: B07V6XSCW2 | Ean: 0681385631272 | UPC: 681385631272
♞【Brief Technical Feature】16 Photoelectric Isolated Digital Inputs,3 Photoelectric Isolated Digital Outputs ; Analog Spindle Control 0-10V Spindle Control (Can Be Modified As Pwm Output) ; Arm9 Main Control Chip,Fpga Core Algorithm Chip ; Jog Function For Each Axis (Continuous, Step, Defined Distance) ; Customer Can Define The Distance ; Support Npn Type Limited Switch..
♞【Applications】The Ddcv3.1 Can Be Used For Many Styles And Types Of Cnc Machines. Lathes, Cnc Routers,Pick&Place And Milling Machine,Lathe Machine And Cutters Are Just A Few Examples..
♞【Mpg Handwheel】Mpg Resolution:100 Ppr ; Switch:X1,X10,X100,With Emergency Stop,Led Indicator, With 15-Pin Plug,So It's Play And Plug..
♞【Compatible With G Code Set】5 Inches Tft Screen ; Resolution Ratio: 480X272 ; The Highest Output Pulse Per Axis Is 500Khz. This Provides High Control Precision For Stepper Motors And Servo Motors. All Operations Are Controlled By Only 17 Keys And It Supports The Fanuc With High Universality To Be Compatible With G Code Set,With 4G Usb Flash Disk Support For G Code File Input,No Size Limited Of The G-Code File..
Features
- Brief introduction The DDCSV3.1 is a 4 axis motion controller,the highest output pulse per axis is 500KHz.This provides high control precision for stepper motors and servo motors.The DDCS operates as a stand alone system without the need of a computer, and it needs two 24V DC power supplies.
- Compatible with G code set 5 inches TFT Screen ; Resolution ratio: 480x272 ; the highest output pulse per axis is 500KHz. This provides high control precision for stepper motors and servo motors. All operations are controlled by only 17 keys and it supports the FANUC with high universality to be compatible with G code set,with 4G USB flash disk support for G code file input,no size limited of the G-code file.
- Brief technical feature 16 photoelectric isolated digital inputs,3 photoelectric isolated digital outputs ; Analog spindle control 0-10V spindle control (can be modified as PWM output) ; ARM9 main control chip,FPGA core algorithm chip ; Jog function for each axis (continuous, step, defined distance) ; Customer can define the distance ; Support NPN type limited switch.
- MPG Handwheel MPG Resolution:100 PPR ; Switch:X1,X10,X100,with Emergency stop,LED indicator, with 15-pin plug,so it's play and plug.
- Applications The DDCV3.1 can be used for many styles and types of CNC machines. Lathes, CNC Routers,Pick&Place and Milling Machine,lathe machine and cutters are just a few examples.
- See more on Amazon...
Brand: CNCTOPBAOS | Manufacturer: Changzhou Rattm Motor Co.,Ltd
See On Amazon #20
CNCTOPBAOS CNC Router GRBL Offline Controller,2.8" Touchscreen LCD Display Touch Screen Off-line Control Module For 3018pro,3018 PRO MAX,3020 Plus,4540,3 Axis GRBL Milling Engraving Machine
Asin: B0CGX3ZLCS
♞【Easy Access To Files Using Sd Card】The Sd Card Contains Some Files For Testing, And You Can Also Put The Desired Files Into The Sd Card.The Functions Of The Touch Screen Offline Controller Are The Same As The Computer's Control Software,And You Can Also Control Every Movement Of The Engraving Machine As If You Were Operating On Top Of The Engraving Machine..
♞【Easy To Operate】The Cnc Offline Controller Is Equipped With A Connecting Cable,Sd Card And A Usb Card Reader,Making It Easy To Install.Only Need To Imply Click On The Offline Controller Manually To Operate, Which Is Simple To Operate, Saves Time, And Improves Your Work Efficiency..
♞【Without Connecting The Pc】You Can Successfully And Easily Operate The Engraving Machine Without Connecting To A Computer,Greatly Improving Work Efficiency;Just Put The Project You Need Inside That Sd Card,And You Can Operate The Engraving Machine Via This Offline Controller..
♞【2.8" Lcd Touchscreen】This Offline Controller Is Equipped With A 2.8 Inch Lcd Touch Screen,The Touch Screen Control Design Of The Offline Machine Can Make Controlling The Engraving Machine More Simple And Convenient;Product Size: 3.74*3.14*0.72”(95*80*18.5Mm).
Features
- Applicable model This grbl offline controller is suitable for 3018,3018 pro,3018 pro max,upgraded 3018 pro,3020 plus,4540 series Cnc router,grbl 1.1 controllers,3 axis milling engraving machines,with good compatibility,very suitable for various engraving carving projects.
- 2.8 LCD Touchscreen This offline controller is equipped with a 2.8 inch LCD touch screen,the touch screen control design of the offline machine can make controlling the engraving machine more simple and convenient;Product Size: 3.74*3.14*0.72 (95*80*18.5mm)
- Easy access to files using SD card The SD card contains some files for testing, and you can also put the desired files into the SD card.The functions of the touch screen offline controller are the same as the computer's control software,and you can also control every movement of the engraving machine as if you were operating on top of the engraving machine.
- Without connecting the PC You can successfully and easily operate the engraving machine without connecting to a computer,greatly improving work efficiency;Just put the project you need inside that SD card,and you can operate the engraving machine via this offline controller.
- Easy to operate The CNC offline controller is equipped with a connecting cable,SD card and a USB card reader,making it easy to install.ONLY need to imply click on the offline controller manually to operate, which is simple to operate, saves time, and improves your work efficiency.
- See more on Amazon...
Brand: CNCTOPBAOS | Manufacturer: Changzhou Rattm Motor Co.,Ltd
Dimensions: 0.72 x 3.74 x 3.14 inches
See On Amazon
Looking For Something Else?
Search