BIGTREETECH Manta M8P V2.0 Integrated Control Board 32Bit Running Klipper with CB1, High Speed 3D Printer Motherboard, Compatible TMC5160T Plus,TMC5160,TMC2209,TMC2240 Stepper Driver (Without CB1)
Asin: B0CHFJYM5N | Model: KINGPRINTER-1020000442 | PartNumber: KINGPRINTER-1020000442
As an Amazon Associate we earn a fee from qualifying purchases when you follow a link to Amazon from this page. We rank the products, but the links to Amazon are promotional.⭐The Control Board And The Core Board Use Btb Connection Method, So That Other Core Board Solutions Other Than Cm4 Can Be Selected, Such As Bigtreetech Cb1. The Mainboard Reserves The Spi Expansion Interface For Using The Klipper Firmware To Connect An External Acceleration Sensor For Acceleration Compensation..
⭐The Mcu Firmware Can Be Upgraded Through Sd Card, Or Through Dfu Through Klipper's Make Flash Command; The Main Board Reserves The Proximity Switch Interface, Supports Npn And Pnp Type Selection, (24V, 12V, 5V) Voltage Optional, Shared With Vfan6 Voltage Selection..
⭐The Thermistor Can Select The Pull-Up Resistance Value Through The Jumper, Which Supports Pt1000 Without External Modules, Which Is Convenient For Diy Use; The Control Board Reserves A Three-Way Four-Wire Fan Interface, Which Can Be Used To Connect A Water Cooling Device..
⭐The Power Chip Of Manta M8p Integrated Main Control Board Adopts Tps5450-5A, Which Supports Dc12/24V Power Input; The Output Current Of This Chip Is Up To 5A, And The Peak Value Can Reach 6A, Which Perfectly Supports The Power Supply Of Raspberry Pi..
Features
- BIGTREETECH Manta M8P V2.0 Control Board uses 32-bit ARM Cortex-M7 series STM32H723ZET6 main control chip with a core frequency of 550MHz. High efficiency MOSFET for less heat generation;
- The power chip of Manta M8P integrated main control board adopts TPS5450-5A, which supports DC12/24V power input; the output current of this chip is up to 5A, and the peak value can reach 6A, which perfectly supports the power supply of Raspberry Pi.
- The control board and the core board use BTB connection method, so that other core board solutions other than CM4 can be selected, such as BIGTREETECH CB1. The mainboard reserves the SPI expansion interface for using the Klipper firmware to connect an external acceleration sensor for acceleration compensation.
- The thermistor can select the pull-up resistance value through the jumper, which supports PT1000 without external modules, which is convenient for DIY use; the control board reserves a three-way four-wire fan interface, which can be used to connect a water cooling device.
- The MCU firmware can be upgraded through SD card, or through DFU through Klipper's make flash command; the main board reserves the proximity switch interface, supports NPN and PNP type selection, (24V, 12V, 5V) voltage optional, shared with VFAN6 Voltage selection.
- See more on Amazon...
Brand: BIGTREETECH | Manufacturer: BIGTREETECH
See On Amazon Similar To BIGTREETECH Manta M8P V2.0 Integrated
#1
BIGTREETECH SKR Mini E3 V3.0 Control Board +TFT35 E3 V3.0.1 Touch Screen Display 32-Bit Silent Board Integrated with TMC2209 UART Stepper Driver Compatible with Ender 3/5 Ender 3 Pro/V2 3D Printer
Asin: B09MYT45BQ | Model: 1060000518 | PartNumber: 1060000518
⭐【Impressive Heat Dissipation】The Btt Skr Mini E3 V3.0 Silent Board Also Looks Aesthetic With Upgraded Designs.New Heatsink And 3 Pwm Controlled Fans Serve To Cool Down The Machine During Printing, Effectively Improving Performances On Heat Dissipation. A Direct 3D Printer Control Board Replacement For Ender 3, Ender 3 Pro, And Ender 5 3D Printer Motherboards..
⭐【Satisfying After-Sales Support】If You Have Any Problems About Btt Skr Mini E3 V3.0 & Tft35 E3 V3.0.1 Smart Display Combo Sets, Please Feel Free To Contact Us Anytime. We Have Profession Technical Supports Team To Help You As Soon As We Can..
⭐【Supports Touch/Graphic Display】Btt Tft35-E3 V3.0 Display Enables You To Easily Switch Between The Marlin Lcd Emulator And Touch Screen With Menu Interface, Simply By Pressing And Holding The Selector Wheel. It's A Plug And Play On Ender Series Printers With Btt Skr Mini E3 V3.0 Control Board.（Note:When Running Klipper Firmware,Tft35 E3 V3.0.1 Display Only Support 12864 Mode).
⭐【Upgraded More Capabilities】Intergrated With Tmc2209 V1.3 Mute Stepper Driver,Bigtreetech Skr Mini E3 V3.0 Motherboard Offers Silent Performance As Default, And Supports Dual Z Steppers For Linear Rail And Belt Upgrades, Filament Runout Support, Automatic Shutdown (Ups Support), Power-Off Resume, Sensorless Homing And So On..
Features
- BIGTREETECH Combo Set Comes with Bigtreetech SKR Mini E3 V3.0 32 bit control board and TFT35 E3 V3.0.1 touch screen display with dual modes as a set. perfect for Ender 3 3D Printer,plug and playing, Adopted the latest G0 series MCU-STM32G0B0RET6 main control chip packing excellent performances.
- Upgraded More Capabilities Intergrated with TMC2209 V1.3 mute stepper driver,BIGTREETECH SKR Mini E3 V3.0 motherboard offers silent performance as default, and supports dual Z steppers for linear rail and belt upgrades, filament runout support, automatic shutdown (UPS support), power-off resume, sensorless homing and so on.
- Impressive Heat Dissipation The BTT SKR MINI E3 V3.0 silent board also looks aesthetic with upgraded designs.New heatsink and 3 PWM controlled fans serve to cool down the machine during printing, effectively improving performances on heat dissipation. A direct 3D printer control board replacement for Ender 3, Ender 3 Pro, and Ender 5 3D Printer motherboards.
- Supports Touch/Graphic Display btt tft35-e3 v3.0 display enables you to easily switch between the Marlin LCD emulator and touch screen with menu interface, simply by pressing and holding the selector wheel. It's a plug and play on Ender series printers with BTT SKR MINI E3 V3.0 control board. Note:When running klipper firmware,tft35 e3 v3.0.1 display only support 12864 mode)
- Satisfying After-Sales Support If you have any problems about BTT SKR MINI E3 V3.0 & TFT35 E3 V3.0.1 smart display combo sets, please feel free to contact us anytime. We have profession technical supports team to help you as soon as we can.
- See more on Amazon...
Brand: BIGTREETECH | Manufacturer: BIGTREETECH
See On Amazon #2
BIGTREETECH Mini12864 V2.0 LCD Graphic Smart Display Control Board with Adapter and Cable for Ender-3 VORON 2.4 Prusa-i3 3D Printer RAMPS 1.4 RepRap 3D Printer Mendel Prusa Arduino
Asin: B08P5LXR86 | Model: KINGPRINT-ZZB000475 | PartNumber: KINGPRINT-ZZB000475 | Ean: 0791568743491 | UPC: 791568743491
3.Product Comes Encoder Parameter Adjustment Can Be Achieved, And The File Selection Print..
5.Do Not Worry About The Problem Of After-Sales, If There Is Any Need, Get In Touch With Us, We Will Help You Solve It..
4.Plug And Play On The Ramps, But Need To Modify The Firmware To Support..
2.With A Sd Card Base On Back, Put Slicing File Into The Sd Card And Select The File On The Lcd, Then Can Be Printing..
Features
- 1.The Mini12864 display panel has RGB multi-color backlight and can support 8 RGB, which is even more cool.
- 2.With a SD card base on back, put slicing file into the SD card and select the file on the LCD, then can be printing.
- 3.Product comes encoder parameter adjustment can be achieved, and the file selection print.
- 4.Plug and play on the RAMPS, but need to modify the firmware to support.
- 5.Do not worry about the problem of after-sales, if there is any need, get in touch with us, we will help you solve it.
- See more on Amazon...
Brand: BIGTREETECH | Manufacturer: BIGTREETECH
Dimensions: 1.18 x 2.36 x 1.18 Inches | Weight: 0.11 pounds
See On Amazon #3
BIGTREETECH TFT35 SPI V2.1 Graphic Smart Display Compatible BTT Manta M8P/M4P/M5P, Manta E3EZ Control Board + CB1 Support Running Klipper Firmware DIY Upgrade 3D Printer
Asin: B0BSCQNF28 | Model: KINGPRINTER-1040000035 | PartNumber: KINGPRINTER-1040000035
3. It Is Connected With The Main Board Through Fpc Cable, Which Is Simple And Convenient To Operate;.
5. Currently, It Only Supports Bigtreetech Cb1. If You Use Cb1 V2.2, You Only Need To Use With Tft35 Spi V2.1; If You Use Cb1 V2.1, You Need To Use With Tft35 Spi V2.1+Io2can V1.0. If You Have Any Questions, You Can Contact Us At Any Time, And We Will Answer Your Questions..
4. Designed With Xh2.54 Terminal, Which Can Communicate With The Board Through The Terminal..
2. Each Motor Drive Shall Select Power Supply, Motor Power Supply Or Main Power Supply (Heating Rod Power Supply) Separately;.
Features
- 1. LCD display adopts SPI, touch adopts I2C communication mode, and shares the main control chip with the motherboard, which greatly reduces the cost of touch screen;
- 2. Each motor drive shall select power supply, motor power supply or main power supply (heating rod power supply) separately;
- 3. It is connected with the main board through FPC cable, which is simple and convenient to operate;
- 4. Designed with XH2.54 terminal, which can communicate with the board through the terminal.
- 5. Currently, it only supports BIGTREETECH CB1. If you use CB1 V2.2, you only need to use with TFT35 SPI V2.1; If you use CB1 V2.1, you need to use with TFT35 SPI V2.1+IO2CAN V1.0. If you have any questions, you can contact us at any time, and we will answer your questions.
- See more on Amazon...
Brand: BIGTREETECH | Manufacturer: BIGTREETECH
See On Amazon #4
BIGTREETECH SFS V2.0 Smart Filament Runout Sensor Upgrade Bi-Directional Photoelectric Filament Break Sensor for 1.75mm Filament for SKR Mini E3 V3.0 Manta M8P Octopus Pro BTT Pi Control Board
Asin: B0C77QS4TS | Model: BIGTREETECH SFS V2.0 | PartNumber: BIGTREETECH SFS V2.0
【Wide Compatibility, Easy Installation】Supports Bowden And Direct-Drive Extruders, With 3 Mounting Holes For Easy Mounting To Printer Using Bracket. Support Motherboards With Available Endstop Ports Or Dedicated Filament Runout Ports, Such As Bigtreetech Skr Mini E3 V3.0, Manta E3ez, Manta M8p, Octopus Pro, Etc. Please Consult Our Technical Support Before Using The Motherboard Without Filament Runout Port..
【Instructions For Use】Insert Filament From The Direct Quick Connector In Any Direction Of Smart Filament Sensor; The Red Light Will Illuminate When There Is No Filament In The Module. The Blue Light Will Flash When The Extrusion Is Normal. The Blue Light Will Stay On Or Off When There Is No Extrusion..
【Photoelectric Sensor Technology】Sfs V2.0 Adopts Photoelectric Sensor Technology, With Theoretical Detection Length Of 2.88Mm, Which Is More Accurate Than The 7Mm Of Sfs V1.0. Please Note: 2.88 Mm Is The Minimum Detection Length Required For The Sensor To Function Properly. If You Encounter Problem Of False Triggers, Try Increasing The Detection Length By 1Mm Increments Until The Problem Is Resolved..
【Multifunctional Detection】Sfs V2.0 Detects Extrusion Errors Caused By Filament Runout, Nozzle Clogging, Filament Tying, And Extruder Trouble. It Has Two Signal Outputs And Indicator Lights To Distinguish Between Clogging Or Filament Runout. Small And Lightweight, It Will Not Add Too Much Pressure To The Printer's Extrusion Head..
Features
- Bi-directional Feeding BIGTREETECH SFS V2.0 is bi-directional, there is no restriction on filament direction, giving you guys more flexibility during installation. It suitable for Marlin, Klipper, and RRF firmware.
- Multifunctional Detection SFS V2.0 detects extrusion errors caused by filament runout, nozzle clogging, filament tying, and extruder trouble. It has two signal outputs and indicator lights to distinguish between clogging or filament runout. Small and lightweight, it will not add too much pressure to the printer's extrusion head.
- Wide Compatibility, Easy Installation Supports Bowden and Direct-Drive extruders, with 3 mounting holes for easy mounting to printer using bracket. Support motherboards with available endstop ports or dedicated filament runout ports, such as BIGTREETECH SKR Mini E3 V3.0, Manta E3EZ, Manta M8P, Octopus Pro, etc. Please consult our technical support before using the motherboard without filament runout port.
- Photoelectric Sensor Technology SFS V2.0 adopts photoelectric sensor technology, with theoretical detection length of 2.88mm, which is more accurate than the 7mm of SFS V1.0. Please Note: 2.88 mm is the minimum detection length required for the sensor to function properly. If you encounter problem of false triggers, try increasing the detection length by 1mm increments until the problem is resolved.
- Instructions for use Insert filament from the direct quick connector in any direction of smart filament sensor; The red light will illuminate when there is no filament in the module. The blue light will flash when the extrusion is normal. The blue light will stay on or off when there is no extrusion.
- See more on Amazon...
Brand: BIGTREETECH | Manufacturer: BIGTREETECH
Warranty: 1年保修
See On Amazon #5
BIGTREETECH BTT UPS 24V V1.0 Resume Printing While Power Off Module Sensor for SKR V1.4 Turbo SKR Mini E3 V3.0 Octopus V1.1 Manta M4p/M5p Ender-3 CR-10 3D Printer Parts
Asin: B081DLBTQC | Model: ZZB000377 | PartNumber: ZZB000377 | Ean: 0787794452443 | UPC: 787794452443
Brand: BIGTREETECH Direct | Manufacturer: BIGTREETECH Direct
See On Amazon #6
BIGTREETECH Manta M5P+CB1 V2.2 Core board 1GB DDR3 Running Linux System Klipper Support TMC2209 HDMI SPI LCD for Ender 3 Voron V0
Asin: B0C2YVYYMR | Model: 1020000397 | PartNumber: 1020000397
🔥【Onboard Multifunctional Ports 】: Btt Manta M5p Onboard Hdmi Interface, Images Can Be Transmitted To Bigtreetech Hdmi5/Hdmi7 Screen Using Only An Hdmi Cable, And Spi Interface, Working With Spi Touch Screen To Create An Intuitive, Responsive Operation, Plug And Play Usb Camera, Monitoring Your 3D Printing Projects Wirelessly..
⭐【Satisfying After-Sales Support】: If You Have Any Problems About Btt Manta M5p Cb1 Core Board Combo Sets, Please Feel Free To Contact Us Anytime. We Have Profession Technical Supports Team To Help You As Soon As We Can..
🔥【More Features Upgraded】: Integrated Spi And Uart Mode Of Tmc Driver And Diag Pin, Easily Configurable With Jumpers.(Such As Tmc2209, Tmc2208, Tmc5160t Pro), Adopts Replaceable Fuse For Easy Replacement And High Efficiency Mostfet For Less Heat Generation, Mcu Firmware Can Be Upgraded Via An Sd Card, Or Use Dfu Via Klipper's Make Flash Command..
🔥【Cb1 Core Board 】: Bigtreetech Cb1 Quad-Core Architecture Is 62Bit, Arm Cortex-A53 @ 1.5Ghz Processor, 1Gb Ddr3 Ram, Support 100M Ethernet +100M Wifi, Run Linux / Support Debian / Progammable, High Speed And High Stability, And Is Convenient For Users To Diy..
Features
- Born For Klipper : BIGTREETECH Manta M5P V1.0 Control board + bigtreetech CB1 V2.2 core board can direct to run the Linux System, then the Klipper, if without the CB1, Can running Marlin firmware, perfect for Ender 3/Voron V0 3D Printer.
- CB1 Core Board : BIGTREETECH CB1 quad-core architecture is 62bit, ARM Cortex-A53 @ 1.5GHz processor, 1GB DDR3 RAM, Support 100M Ethernet +100M WIFI, run Linux / Support Debian / progammable, High Speed and high stability, and is convenient for users to DIY.
- Onboard Multifunctional Ports : BTT Manta M5P onboard HDMI interface, images can be transmitted to BIGTREETECH HDMI5/HDMI7 Screen using only an HDMI cable, and SPI interface, working with SPI touch screen to create an intuitive, responsive operation, plug and play USB camera, monitoring your 3D printing projects wirelessly.
- More Features Upgraded : Integrated SPI and UART mode of TMC driver and DIAG pin, easily configurable with jumpers.(such as TMC2209, TMC2208, TMC5160T Pro), Adopts replaceable fuse for easy replacement and High efficiency Mostfet for less heat generation, MCU firmware can be upgraded via an SD card, or use DFU via Klipper's make flash command.
- Satisfying After-Sales Support : If you have any problems about BTT Manta M5P CB1 Core board combo sets, please feel free to contact us anytime. We have profession technical supports team to help you as soon as we can.
- See more on Amazon...
Brand: BIGTREETECH | Manufacturer: BIGTREETECH
Dimensions: 0.39 x 3.93 x 1.96 inches
See On Amazon #7
BIGTREETECH SKR V1.4 Control Board 32bit Upgrade SKR V1.3 Motherboard, Compatible TFT35/TFT35 E3/TFT70 Touch Screen Mini12864 LCD Support TMC2209/EZ2209/TMC2208/TMC5160 for Most FDM 3D Printer
Asin: B0BHNVFR1M | Model: KINGPRINTER-1020000399 | PartNumber: KINGPRINTER-1020000399
⭐Support 2.4, 2.8, 3.5-Inch Color Touch Screen, Support Lcd2004 Screen, Lcd12864 Screen; Upgrade Configuration Firmware Through Sd Card, Simple, Convenient And Efficient Operation..
⭐On-Board Tmc Driver Spi Working Mode And Uart Working Mode, And The On-Board Diag Function Pins Are Convenient For Customers To Use, Eliminating The Complicated Wiring Process, Which Can Be Used By Simply Removing And Inserting The Jumper Cap; Functions Such As Continuous Power On, Material Detection, Shutdown After Power Off..
⭐It Can Supply Power To Tft Screen, Bltouch, Neo-Pixel By Plugging In An External Dc5v Power Module; In Addition, I2c, Spi, Wifi Interface Is Reserved To Facilitate Customer Diy..
⭐Equipped With Highly Modular Open Source Firmware Marlin 2.0, Which Is Convenient For Users To Diy And Secondary Development..
Features
- Using 32-bit 100MHz ARM-class Cortex-M3 series LPC1768 main control chip, the performance is greatly improved.
- Equipped with highly modular open source firmware Marlin 2.0, which is convenient for users to DIY and secondary development.
- Support 2.4, 2.8, 3.5-inch color touch screen, support LCD2004 screen, LCD12864 screen; Upgrade configuration firmware through SD card, simple, convenient and efficient operation.
- It can supply power to TFT screen, BLtouch, Neo-pixel by plugging in an external DC5V power module; in addition, I2C, SPI, WIFI interface is reserved to facilitate customer DIY.
- On-board TMC driver SPI working mode and UART working mode, and the on-board DIAG function pins are convenient for customers to use, eliminating the complicated wiring process, which can be used by simply removing and inserting the jumper cap; Functions such as continuous power on, material detection, shutdown after power off.
- See more on Amazon...
Brand: BIGTREETECH | Manufacturer: BIGTREETECH
See On Amazon #8
BIGTREETECH Manta E3EZ + CB1 V2.2 + 5Pcs EZ2209 Kit Support Running Klipper Firmware Silent Control Board Kit for Ender-3 V2, Ender-3 Pro, Ender-3, BIQU B1 3D Printers
Asin: B0C6LLFBN5 | Model: KINGPRINT-1029549 | PartNumber: KINGPRINT-1029549
The Bigtreetech Manta E3 Ez Main Control Board And Core Board Use Btb Connection, Which Can Be Perfectly Paired With The Bigtreetech Cb1 Core Board..
Bigtreetech Ez2209 Using A New Customized Heat Sink, While Enhancing The Heat Dissipation Capacity, It Protects The Driver Chip From External Damage; The Newly Developed Board Frame Is Used To Match The New Connector To Improve The User Experience..
Bigtreetech Cb1 Is Equipped With Quad Core 64 Bit Arm Cortex-A53 @ 1.5Ghz Processor, 1Gb Ddr3 Memory Chip; Onboard 100M Ethernet Interface And Supports Wifi Transmission..
Manta E3ez Adopts Arm Cortex-M0+Series Stm32g0b1re Master Chip With 32-Bit Main Frequency Of 64Mhz; The Maximum Power Supply Of The Motor Is 56V;.
Features
- This kit includes BIGTREETECH Manta E3EZ silent control board, CB1 V2.2 core control board, and 5PCS EZ2209 stepper motor drivers.
- Manta E3EZ adopts ARM Cortex-M0+series STM32G0B1RE master chip with 32-bit main frequency of 64MHz; The maximum power supply of the motor is 56V;
- The BIGTREETECH Manta E3 EZ main control board and core board use BTB connection, which can be perfectly paired with the BIGTREETECH CB1 core board.
- BIGTREETECH CB1 is equipped with quad core 64 bit ARM Cortex-A53 @ 1.5GHz processor, 1GB DDR3 memory chip; Onboard 100M Ethernet interface and supports WIFI transmission.
- BIGTREETECH EZ2209 using a new customized heat sink, while enhancing the heat dissipation capacity, it protects the driver chip from external damage; The newly developed board frame is used to match the new connector to improve the user experience.
- See more on Amazon...
Brand: BIGTREETECH | Manufacturer: BIGTREETECH
See On Amazon #9
BIGTREETECH TFT35 V3.0.1 Touch Screen Display with Two working Modes Smart Controller Panel Compatible with LCD12864 WiFi for Octopus V1.1/ SKR V1.4 turbo/SKR 3/Manta M4P/M5P SKR Pro Ender3 3D Printer
Asin: B07VWGFKLZ | Model: K-03101171 | PartNumber: K-03101171 | Ean: 0778365968586 | UPC: 778365968586
※【More Reserved Extensions】 :Tft35 V3.0.1 Touch Screen Reserves The Extension Ports Of Filament Break Detection, Automatic Shutdown After Printing, Also Wifi Function Can Be Realized By External Wifi Module Through Wifi Port. Compatible With Skr Mini E3 V3.0/Skr V1.4 Turbo/Octopus/Skr 3/Skr 3 Ez/Manta M4p/5P/8P Control Board.
※【100% Technical Supports】: If You Have Any Problems About Btt Tft35 V3.0.1 Touchscreen, Please Feel Free To Contact Us On Amazon. Our Technical Supports Team Will Respon To You Within 24 Hours. 1-Year Warranty Is 100% Guaranteed!.
※【Easy Firmware Updates】: It Is Easy And Convenient To Update Firmware By Sd Card, Simply Downloading From Github, Coping And Saving It To Sd Card. Firmware Must Be Reserved, Then Re-Plug The Sd Card And Wait To 10S. That's All Takes To Finish Updating On Firmware..
※【Dual Working Modes】: Btt Tft35 V3.0.1 Display Enables Two Different Modes, With Options For Either Lcd12864 Encoder Mode, Or The Modern Colour Touch Screen Style. It Also Supports Both Sd Card And Usb Stick Printing..
Features
- 32 Bit Microprocessor : bigtreetech tft35 v3.0.1 display Adopted ARM Cortex-M3 series GD32F205VCT6 master controller chip with 32-bit CPU main frequency of 120 MHz, BTT TFT35 V3.0.1 touch screen can perfectly replace the LCD12864 screen for use.
- Dual Working Modes : BTT TFT35 V3.0.1 display enables two different modes, with options for either LCD12864 Encoder Mode, or the modern Colour Touch Screen Style. It also supports both SD card and USB stick printing.
- More Reserved Extensions :TFT35 V3.0.1 touch screen reserves the extension ports of filament break detection, automatic shutdown after printing, also WIFI function can be realized by external WIFI module through WIFI port. compatible with SKR MINI E3 V3.0/SKR V1.4 Turbo/Octopus/SKR 3/SKR 3 EZ/Manta M4P/5P/8P Control board
- Easy Firmware Updates : It is easy and convenient to update firmware by SD card, simply downloading from Github, coping and saving it to SD card. firmware must be reserved, then re-plug the SD card and wait to 10s. That's all takes to finish updating on firmware.
- 100% Technical Supports : If you have any problems about BTT TFT35 V3.0.1 touchscreen, please feel free to contact us on Amazon. Our technical supports team will respon to you within 24 hours. 1-Year Warranty is 100% guaranteed!
- See more on Amazon...
Brand: BIGTREETECH | Manufacturer: BIGTREETECH Direct
See On Amazon #10
BIGTREETECH Octopus V1.1 Control Board 32bit Compatible TFT Series Screen, Support DIY Klipper Firmware and Raspberry-Pi Online Printing for Voron V2.4 Upgrade 3D Printer (with 8Pcs TMC2209)
Asin: B09713SRVP | Model: KINGPRINTER-UUU001949 | PartNumber: KINGPRINTER-UUU001949
🐙【Motherboard Expansion Function】Support Bltouch, Locked-Rotor Detection, Shutdown After Printing, Resume Printing After Power Failure, Can Bus, U Disk Function, Iic Expansion; At The Same Time Reserved Wifi Interface, Pt100 Thermistor Interface (Optional), Dual Z-Axis Printer..
🐙【Tmc2209 Driver Mode】Tmc Motor Drivers Can Be Used In Spi Or Uart Mode By Simply Adjusting The Onboard Jumpers Beneath Each Motor Driver. Additionally You Can Connect Or Disconnect The Tmc Diag Pin Using An Onboard Jumper Allowing You To Use Hard Endstops Or Sensorless Homing Without The Need To Cut Any Pins..
🐙【Tmc2209 Driver Features】The Tmc2209 Stepper Driver Is Not Easy To Lose Steps And Is In An Ultra-Quiet Mode; The Module Has A Large Area Of Heat Dissipation Pad, Which Can Reduce The Temperature Of The Driver When It Is Working; The Module Supports Three Modes: Step / Dir And Uart..
🐙【Strong Diy Support】This Motherboard Supports Up To 8 Stepper Drivers With 9 Stepper Driver Outputs In Total; And Up To 6 Pwm Fans And 2 Always-On Fans With The Ability To Individually Select The Voltage Rail That Will Drive Each Fan. Select From Vin, 12V Or 5V..
Features
- Main Control Chip Uses a 32-bit ARM Cortex-M4 series STM32F446ZET6 main control chip with a core frequency of 180MHz.
- Strong DIY Support This motherboard supports up to 8 stepper drivers with 9 stepper driver outputs in total; And up to 6 PWM fans and 2 always-on fans with the ability to individually select the voltage rail that will drive each fan. Select from Vin, 12V or 5V.
- Motherboard Expansion Function Support BLTouch, locked-rotor detection, shutdown after printing, resume printing after power failure, CAN bus, U disk function, IIC expansion; at the same time reserved WIFI interface, PT100 thermistor interface (optional), dual Z-axis printer.
- TMC2209 Driver Features The TMC2209 stepper driver is not easy to lose steps and is in an ultra-quiet mode; the module has a large area of heat dissipation pad, which can reduce the temperature of the driver when it is working; the module supports three modes: STEP / DIR and UART.
- TMC2209 Driver Mode TMC Motor drivers can be used in SPI or UART mode by simply adjusting the onboard jumpers beneath each motor driver. Additionally you can connect or disconnect the TMC DIAG pin using an onboard jumper allowing you to use hard endstops or sensorless homing without the need to cut any pins.
- See more on Amazon...
Brand: BIGTREETECH | Manufacturer: BIGTREETECH
See On Amazon #11
BIGTREETECH Direct Relay V1.2 Automatic Shutdown Module After Printing Support Resume Printing While Power Off for SKR Mini E3 V3.0 Octopus V1.1 Manta M4P/M5P/M8P/SKR V1.4 Turbo Ender 3 3D Printer
Asin: B07QJ4MZVN | Model: ZZB000239 | PartNumber: ZZB000239 | Ean: 0778601687363 | UPC: 778601687363
Bigtreetech Relay V1.2 Is Easy To Understand, Its Logo Is Clearly Visible And Its Function Is Practical..
Btt Relay V1.2 Compatible With Bigtreetech Skr Mini E3 V3.0/Skr Mini E3 V2.0/Skr V1.4 Turbo/Manta M4p/Mp/M8p/Octopus Pro/Octopus V1.1/Mks Gen L ...3D Printer Control Board.
The Function Is To Automatically Detect Whether The 3D Printing Of The Project Printer Is Completed. When It Is Detected That The Project Is Printed, The Power Can Be Automatically Turned Off. The Goal Is To Create An Automated 3D Printing Environment With Low Carbon Content, Environmental Protection, Energy Savings And Reduced Consumption..
Features
- BIGTREETECH Relay V1.2 module is the first automatic shutdown module independently developed by BIGTREETECH Tecnologia.
- The function is to automatically detect whether the 3D printing of the project printer is completed. When it is detected that the project is printed, the power can be automatically turned off. The goal is to create an automated 3D printing environment with low carbon content, environmental protection, energy savings and reduced consumption.
- BIGTREETECH relay V1.2 is easy to understand, its logo is clearly visible and its function is practical.
- BTT Relay V1.2 Compatible with BIGTREETECH SKR MINI E3 V3.0/SKR MINI E3 V2.0/SKR V1.4 Turbo/Manta M4p/MP/M8P/Octopus pro/Octopus V1.1/MKS GEN L ...3D Printer Control board
- See more on Amazon...
Brand: BIGTREETECH Direct | Manufacturer: BIGTREETECH DIRECT
See On Amazon #12
BIGTREETECH TFT35 SPI V2.1 Touch Screen Display 3.5 Inches Smart Controller Panel Use with CB1 + BTT Manta E3EZ / Manta M8P / Manta M4P / Manta M5P to Run Klipper
Asin: B0BRZ4RL1P
🍀【Reserved Extension Ports】Designed With Xh2.54 Terminal, Which Can Communicate With The Board Through The Terminal..
🍀【Quality Warranty】We Offer A 12 Months Quality Warranty Period For Our Products. If You Have Any Question And Feedback Please Feel Free To Contact Us, Our Professional Technical Team Will Try Best To Help You..
🍀【Compatible With Btt Cb1】Tft35 Spi Touch Screen Is Compatible With All Versions Of Btt Cb1 Core Board. It Can Directly Use With Cb1 V2.0 And Cb1 V2.2, And Need To Match Up With Io2can Expansion Module When Used With Cb1 V2.1..
🍀【Responsive & Easy Operation】Tft35 Spi Is A 3.5 Inch Full-Color Screen With Ultra Clear Display And Responsive Touch. It Is Connected To The Motherboard Through The Fpc Cable, Simple And Convenient To Use, Greatly Improving Your Klipper Experience..
Features
- TFT35 SPI Touch Screen BIGTREETECH TFT35 SPI display is a resistive touch screen that controlled by the motherboard chip. Its LCD display is supported by SPI and touch function is supported by I2C. Appearance size: 98*56mm, power input : 5V.
- Responsive & Easy Operation TFT35 SPI is a 3.5 inch full-color screen with ultra clear display and responsive touch. It is connected to the motherboard through the FPC cable, simple and convenient to use, greatly improving your klipper experience.
- Reserved Extension Ports Designed with XH2.54 terminal, which can communicate with the board through the terminal.
- Compatible with BTT CB1 TFT35 SPI touch screen is compatible with all versions of BTT CB1 core board. It can directly use with CB1 V2.0 and CB1 V2.2, and need to match up with IO2CAN expansion module when used with CB1 V2.1.
- Quality Warranty We offer a 12 months quality warranty period for our products. If you have any question and feedback please feel free to contact us, our professional technical team will try best to help you.
- See more on Amazon...
Brand: BIQU | Manufacturer: BIQU
See On Amazon #13
BIGTREETECH Manta M4P V2.2 32-Bit Control Board 4-axis Motherboard 64MHz Compatible CM4 & CB1 Supports 4 Stepper Drivers Klipper Marlin 3D Printer Parts
Asin: B0B87C6W8B | Model: Manta M4P | PartNumber: Manta M4P
✅【Multiple Functions】Btt Manta M4p V2.2 Support Stepper Driver Spi/Uart/Step/Dir Working Mode Such As Tmc2209/Tmc2208 Etc, Bltouch, Microprobe V2.0, Sfs V2.0 Smart Filament Sensor, Rgb Lights, Auto Shutdown And Other Functions. Onboard Hdmi Interface, Dsi/Csi Interface (Need To Be Used With Cm4), Bring Higher Picture Quality Experience, Widely Compatible With Various Cnc Fans..
✅【Firmware Upgrade】: Mcu Can Be Upgraded Through Sd Card, Or Mcu Firmware Can Be Updated Through Dfu Via Klipper's "Make Flash" Command. If You Have Any Problems Regarding Bigtreetech Manta M4p V2.2, Please Feel Free To Contact Us On Amazon..
✅【Higher Security】: Esd Protection Device At Usb And Ethernet Ports Help To Prevent Electrostatic Hazards.The Protection Circuit On Thermistor Prevents The Main Control Chip From Burning Due To Leakage Of The Heated Bed Or Heater Cartridge..
✅【Powerful Performance】: Equipped With 32-Bit 64Mhz Arm Cortex-M0+ Series Chip, More Consistent And Faster.The Tps5450-5A Power Chip Allows For Power Input Of Dc12/24V, With The Chip's Current Output Up To 5A, Peak Value 6A, Which Perfectly Supports The Power Supply Of The Core Board..
Features
- Integrated design : Onboard same BTB connector with Raspberry Pi Eco, you can directly install CB1, or Raspberry-Pi CM4, etc., run Linux system efficiently, and use Klipper firmware.In addition, it is possible to run the Marlin firmware independently without CB1/CB2/CM4. The best choice for Voron V0,Ender 3 3d printer!
- Powerful performance : Equipped with 32-bit 64MHz ARM Cortex-M0+ series chip, more consistent and faster.The TPS5450-5A power chip allows for power input of DC12/24V, with the chip's current output up to 5A, peak value 6A, which perfectly supports the power supply of the core board.
- Multiple Functions BTT Manta M4P v2.2 Support stepper driver SPI/UART/STEP/DIR working mode such as TMC2209/TMC2208 etc, BLTouch, MicroProbe V2.0, SFS V2.0 Smart filament sensor, RGB lights, auto shutdown and other functions. Onboard HDMI interface, DSI/CSI interface (need to be used with CM4), bring higher picture quality experience, widely compatible with various CNC fans.
- Higher security : ESD protection device at USB and Ethernet ports help to prevent electrostatic hazards.The protection circuit on thermistor prevents the main control chip from burning due to leakage of the heated bed or heater cartridge.
- Firmware upgrade : MCU can be upgraded through SD card, or MCU firmware can be updated through DFU via Klipper's make flash command. If you have any problems regarding BIGTREETECH manta M4P v2.2, please feel free to contact us on Amazon.
- See more on Amazon...
Brand: BIGTREETECH | Manufacturer: BIGTREETECH
Dimensions: 0.39 x 6.29 x 3.74 inches
See On Amazon #14
BIGTREETECH SKR Mini E3 V3.0 Control Board with TMC2209 UART Upgrade 32Bit 3D Printer Silent Board for Ender 3, Ender3 Pro, Ender-3 V2 (with BIQU MicroProbe V2 + Ender-3 Mounting Bracket)
Asin: B0CFL6P6MC | Model: KINGPRINTER-1033346 | PartNumber: KINGPRINTER-1033346
Skr Mini E3 Silent Board Is A Four Axis Motherboard Specifically Designed For Ender-3 Players. It Adds Cnc Fans For Overall Heat Dissipation And Upgrades Heat Sink, Effectively Improving Heat Dissipation Performance..
Biqu Microprobe Is Only 6G, And Its Smaller Size Enhances The Compatibility Of Microprobe Installation Positions, Allowing For Better Installation In Some Compact Positions On Extruder; With A Lifespan Of 10000000+, Microprobe Will Be A Durable Upgrade For Your Printer..
Biqu Microprobe V2 Uses 5V Power Supply, The Control Signal Is Compatible With 3.3V/5V. The Detection Signal Is An Open-Drain Output Externally (10K Pull-Up Resistance Is Required On The Signal Of The Motherboard, Or The Io Needs To Be Set As Input Pull-Up In The Firmware)..
Bigtreetech Skr Mini E3 V3.0 Adopts Stmicroelectronics' Latest G0 Series Main Control Chip Stm32g0b1ret6; It Is Equipped With Tmc2209 Mute Driven Uart Mode On Board And Supports Mute Printing..
Features
- The kit includes BIGTREETECH SKR Mini E3 V3.0 silent control board and BIQU MicroProbe V2 auto leveling sensor, and ender-3 extruder bracket, perfect for Ender-3 and Ender-3 V2 3D printers.
- BIGTREETECH SKR Mini E3 V3.0 adopts STMicroelectronics' latest G0 series main control chip STM32G0B1RET6; It is equipped with TMC2209 mute driven UART mode on board and supports mute printing.
- SKR Mini E3 silent Board is a four axis motherboard specifically designed for Ender-3 players. It adds CNC fans for overall heat dissipation and upgrades heat sink, effectively improving heat dissipation performance.
- BIQU MicroProbe V2 uses 5V power supply, the control signal is compatible with 3.3V/5V. The detection signal is an open-drain output externally (10K pull-up resistance is required on the signal of the motherboard, or the IO needs to be set as input pull-up in the firmware).
- BIQU MicroProbe is only 6g, and its smaller size enhances the compatibility of MicroProbe installation positions, allowing for better installation in some compact positions on extruder; With a lifespan of 10000000+, MicroProbe will be a durable upgrade for your printer.
- See more on Amazon...
Brand: BIGTREETECH | Manufacturer: BIGTREETECH
See On Amazon #15
BIGTREETECH Manta M5P V1.0 Control Board 32Bit Support 5 Axis TMC2209 TMC5160 Drivers Compatible with CB1/CB2/CM4 HDMI5 PITFT50 TFT35 SPI Display to Running Klipper for Ender 3/Voron V0 FDM 3D Printer
Asin: B0C1TYD86S | Model: BIGTREETECH | PartNumber: BIGTREETECH
👉【Rich Expansion Ports】: Support Filament Runout Detection Sensor, Bltouch, Biqu Microprobe, Rgb Lights, Automatic Shutdown Module, Onboard Proximity Switch And Spi（Adxl345 ）Port ,Support Npn And Pnp Type Selection,(24V,12V,5V)Voltage Selection, For Users Use Klipper Firmware To Connect External Acceleration Sensor For Acceleration Compensation..
👉 【 Power Chip Upgraded 】: The Power Chip Adopts Tps5450-5A Power Chip，The 5A Output Perfectly Matches The Power Supply Need Of Raspberry Pi, Integrated Spi And Uart Mode Of Tmc Driver And Diag Pin,Easily Configur Able With Jumpers..
【❤️100% Technical Supports】: If You Have Any Problems About Manta M5p Control Board, Please Feel Free To Contact Us On Amazon. Our Technical Supports Team Will Respon To You Within 24 Hours.We Will Try Our Best Give You A Satisfactory Solution..
👉【 Easy Operation 】: Thermistor Can Select The Value Of Pull-Up Resistor Through Jumper To Support Pt1000 Without External Module Convenient For User To Diy And The Mcu Firmware Can Be Upgraded Through Sd Card, Or Updated Through Dfu Through Klipper's Makeflash Command..
👉【Abundant Connectivity】：Btt Manta M5p Support Usb2.0*3, Lan,Dsc,Csi, Spi, Hdmi0 And Hdmi1 Display (Pitft50 V2.1, Hdmi5 V1.1, Tft35 Spi), Soc-Card, Mcu-Card, Onboard Can, Probe,Rgb*2, Spi,Exp1+Exp2, Min1-Min4, 40Pin-Gpio (About Canbus,Can Be Directly Connected To Ebb Using Klipper's Usb To Can Bus Bridge Function)..
Features
- Main Control Chip Upgraded : BIGTREETECH Manta M5P control board adopts 32bit ARMCortex-M0STM32G0B1RET6 chip, frequency of 64MHz,can installation of the BIGTREETECH CB2/CB1/eMMc/Raspberry-Pi CM4 to run the Linux systyem, using Klippe, without CB1 or CM4, Can Running Marlin.
- Abundant Connectivity BTT Manta M5P support USB2.0*3, LAN,DSC,CSI, SPI, HDMI0 and HDMI1 display (PITFT50 V2.1, HDMI5 V1.1, TFT35 SPI), SOC-Card, MCU-Card, Onboard CAN, Probe,RGB*2, SPI,EXP1+EXP2, MIN1-MIN4, 40Pin-GPIO (about CANBUS,Can be directly connected to EBB using Klipper's USB to CAN bus bridge function).
- Rich Expansion Ports : Support filament runout detection sensor, BLtouch, BIQU Microprobe, RGB Lights, automatic shutdown module, Onboard proximity switch and SPI ADXL345 port ,support NPN and PNP type selection,(24V,12V,5V)voltage selection, for users use Klipper firmware to connect external acceleration sensor for acceleration compensation.
- Easy operation : Thermistor can select the value of pull-up resistor through jumper to support PT1000 without external module Convenient for user to DIY and the MCU firmware can be upgraded through SD card, or updated through DFU through Klipper's makeflash command.
- Power chip upgraded : The Power Chip adopts TPS5450-5A Power Chip the 5A output perfectly matches the power supply need of Raspberry Pi, Integrated SPI and UART mode of TMC driver and DIAG pin,easily configur able with jumpers.
- 100% Technical Supports : If you have any problems about manta M5P control board, please feel free to contact us on Amazon. Our technical supports team will respon to you within 24 hours.we will try our best give you a satisfactory solution.
- See more on Amazon...
Brand: BIGTREETECH | Manufacturer: BIGTREETECH
Dimensions: 1.93 x 6.54 x 4.76 Inches
See On Amazon #16
BIGTREETECH TFT50 V3.0.1 Touch Screen Display Dual Mode 12864 LCD Display Ultra Clear 12 White LED Lights for SKR V1.4 Turbo Octopus V1.1 SKR Mini E3 V3.0 SKR 3 SKR 3 EZ 3D Printer Motherboard
Asin: B08B34CXTV | Model: TFT50 V3.0.1 | PartNumber: TFT50 V3.0.1 | Ean: 0779605889654 | UPC: 779605889654
🍀Tft50 V3.0.1 Screen Firmware Is Upgraded,Support Dual Operating System Can Be Switched With One Clickand Marlin / Touch Screen Mode , Multi-Select Printing Mode,U Disk / Tft Sd /Onboard Sd Printing,Very Easier And Convenient.
🍀Satisfying Customer Services: If You Need Any Help From Us,Please Feel Free To Contact Us Via Amazon Message.Ways Of Getting Firmware,Connecting Customer Service Or Technicians. Log In The Open Source Website: Search Bigtreetech At Githubwe Have Tech Supports Online To Take Care Of Your Problems..
🍀 Widely Compatible：Tft50 V3.0.1 Support Automatic Shutdown After Printing/ Broken Filament Detection/Wifi Module,Compatilbe With Skr Mini E3 V3.0/Skr V1.4 Turbo/Octopus/Skr 3/Skr 3 Ez Mks Gen L Etc..3D Printer Motherboard..
🍀 Btt Tft50 V3.0.1 Touch Screen Display Reserve Wifi Interface,Support External Wifi Module To Realize Wifi Function,With12 White Led Brightness Can Be Adjusted Led Sleep Brighneess And Time Can Be Set,Eye Protection, Energy Saving.
Features
- Main Control Chip BIGTREETECH TFT50 V3.0.1 display adopts ARM 32 bit and 120MHz GD32F205VCT6 of Cortex-M3 series.
- BTT TFT50 V3.0.1 touch screen display reserve wifi interface,support external wifi module to realize wifi function,with12 white LED brightness can be adjusted LED sleep brighneess and time can be set,eye Protection, energy Saving
- TFT50 V3.0.1 screen firmware is upgraded,support dual operating system can be switched with one clickand Marlin / touch screen mode , multi-select printing mode,U Disk / TFT SD /Onboard SD printing,very easier and convenient
- Widely Compatible TFT50 V3.0.1 support automatic shutdown after printing/ Broken filament detection/WIFI module,compatilbe with SKR MINI E3 V3.0/SKR V1.4 Turbo/Octopus/SKR 3/SKR 3 EZ MKS GEN L etc..3D printer motherboard.
- Satisfying Customer Services: If you need any help from us,please feel free to contact us via Amazon message.Ways of getting firmware,Connecting customer service or technicians. Log in the open source website: Search BIGTREETECH at GitHubWe have tech supports online to take care of your problems.
- See more on Amazon...
Brand: BIGTREETECH Direct | Manufacturer: BIGTREETECH Direct
See On Amazon #17
BIGTREETECH TFT35 E3 V3.0.1 Graphic Smart Display Panel Board for Ender 3 Compatible with SKR Mini E3 V3.0, SKR 3/EZ, Octopus/Pro/Max EZ, Kraken, SKR Pro V1.2 Control Board
Asin: B08182XHZZ | Model: TFT35 E3 V3.0.1 | PartNumber: TFT35 E3 V3.0.1 | Ean: 0778601688131 | UPC: 778601688131
3）Reserve Wifi Port, And Wifi Function Is Realized By External Wifi Module；Reserve The Extension Port Of Filament Breaking Detection (Fil-Det)；.
5）Lcd12864 Mode Uses Exp1, Exp2 And Exp3. Exp1 And Exp2 Are Lcd Screen Ports Of Normal Motherboard. Exp3 Is The Lcd Interface Used By E3 Series Motherboard (Such As Skr Mini E3 V1.2, Skr E3 Dip V1.1, Etc.).
4）Reserve The Extension Port Of Automatic Shutdown After Printing (Ps-On);.
2）This Display Board Has Higher Compatibility. Users Can Select Two Work Modes:Uart Serial Port Screen Mode And 12864 Screen Mode;Serial Port Screen Mode Supports Two Printing Modes: Sd Card And U Disk..
Features
- 1 ARM Cortex-M3 series GD32F205VCT6 chip with 32-bit CPU 120MHz; Upgrade the firmware by SD card. It is easy and convenient to operate.
- 2 This display board has higher compatibility. Users can select two work modes:UART serial port screen mode and 12864 screen mode;Serial port screen mode supports two printing modes: SD card and U disk.
- 3 Reserve WIFI port, and WIFI function is realized by external WIFI module Reserve the extension port of filament breaking detection (FIL-DET)
- 4 Reserve the extension port of automatic shutdown after printing (PS-ON);
- 5 LCD12864 mode uses EXP1, EXP2 and EXP3. EXP1 and EXP2 are LCD screen ports of normal motherboard. EXP3 is the LCD interface used by E3 series motherboard (such as SKR MINI E3 V1.2, SKR E3 DIP V1.1, etc.)
- See more on Amazon...
Brand: BIGTREETECH | Manufacturer: BIGTREETECH
See On Amazon #18
BIGTREETECH TMC5160T Plus V1.0 Stepper Motor Driver 8V-60V StepStick SPI Silent High Speed Printing For Marlin/Klipper/RRF Firmware Manta M8P V2.0/V1.0, Octopus Pro Control Board (With All-Metal Case)
Asin: B0CHFHZWBS
Integrated Heat Sink Design, Providing High Heat Dissipation While Enhancing Structural Integrity And Aesthetics; Heat Sink Pre-Designed With Fan Mounting Holes For Diy Fan Installation..
Supplied With Adapters And Wires For Both Standard Drives And Ez Drive, For User Convenience; Encoder Interface Reserved For Diy Usage;.
On-Board 24V Always-On Fan Interface Facilitates Active Cooling; Esd Protection On The Drive Power, Logic Power, Etc., To Prevent Damage Due To Power Fluctuations And Static Electricity;.
Supports A Maximum Voltage Of 60V, A Maximum Effective Current (Irms) Of 10.6A, And A Sine Wave Peak Current Of Up To 15A; Stealthchop Mode And Spreadcycle Mode Selectable, With Standalone Mode, Uart Mode, And Spi Mode Selectable;.
Features
- 8 high-power MOSFETs separately mounted on the motherboard with 100V voltage resistance, 93A current resistance, and equivalent resistance as low as 6m , significantly enhancing the drive's performance;
- Supports a maximum voltage of 60V, a maximum effective current (IRMS) of 10.6A, and a sine wave peak current of up to 15A; StealthChop mode and SpreadCycle mode selectable, with standalone mode, UART mode, and SPI mode selectable;
- Integrated heat sink design, providing high heat dissipation while enhancing structural integrity and aesthetics; Heat sink pre-designed with fan mounting holes for DIY fan installation.
- On-board 24V always-on fan interface facilitates active cooling; ESD protection on the drive power, logic power, etc., to prevent damage due to power fluctuations and static electricity;
- Supplied with adapters and wires for both standard drives and EZ drive, for user convenience; Encoder interface reserved for DIY usage;
- See more on Amazon...
Brand: BIGTREETECH | Manufacturer: BIGTREETECH
See On Amazon #19
BIGTREETECH Manta E3EZ V1.0 Mainboard + EZ2209 V1.0 Stepper Motor Driver 5PCS 32 Bit Silent Control Board Drop-in Klipper Motherboard for Ender 3
Asin: B0CNXQHCVJ
🌞【Ez Driver Slot】Manta E3ez Main Board Adopts Btt Ez Safe Anti-Misplug Design. Matching With Btt Ez Drivers, Our Motherboard Will Keep You Away From Hidden Dangers Like Catching Fire Or Motherboard Ruin Caused By Driver Mis-Plug. Start A Faster And Safer Printing With Bigtreetech E3 Ez!.
🌞【Better Heat Dissipation】 An Innovative 2 In 1 Combination Of Stepper Driver And New Large Aluminum Heat Sink Enables Ez2209 Stepper Driver Better Heat Dissipation, Declining Energy Consumption To A Minimum As Well As Protecting The Driver Chip From External Damage..
🌞【Wide Application Ez2209】Size: 18.5*19.8 Mm, Drive Current 1.6A, Peak Current 2A, Voltage Range12 V- 24 V, 256 Subdivision. Btt Ez2209 Stepper Motor Driver Can Directly Use With Mnata E3 Ez And Skr 3 Ez Motherboard. Ez2209 Can Also Well-Matched With I3 Mega, Octopus V1.2, Skr 3 And Other Popular Main Boards By Using Btt Ez Driver Connector..
🌞【Robust Power System】Btt Manta E3ez Equips With 32Bit 64Mhz Arm Cortex-M0+ Series Stm32g0b1re Mcu And Tps5450-5A Power Chip Which Supports Power Input Of Dc12/24V And Output Current Of 5A (Peak Output 6A ). With Its Powerful System, Manta E3 Ez Can Be A Sufficient Power Supply For Raspberry Pi..
Features
- Klipper Mainboard Combo for Ender-3 This combo set fits those who already have raspberry-pi or cm4 to upgrade your ender-3. BIGTREETECH Manta E3 EZ control board features a board to board design which allows users to directly mount BTT CB1 or raspberry-pi-CM4 core board on it to run Klipper. Onboard SPI interface is for connecting acceleration sensor to enable Klipper's input shaping. And our PC-level motherboard is also a drop-in replacement for Ender 3.
- Robust Power System BTT Manta E3EZ equips with 32bit 64MHz ARM Cortex-M0+ series STM32G0B1RE MCU and TPS5450-5A power chip which supports power input of DC12/24V and output current of 5A (peak output 6A ). With its powerful system, Manta E3 EZ can be a sufficient power supply for Raspberry PI.
- EZ Driver Slot Manta E3EZ main board adopts BTT EZ safe anti-misplug design. Matching with BTT EZ drivers, our motherboard will keep you away from hidden dangers like catching fire or motherboard ruin caused by driver mis-plug. Start a faster and safer printing with BIGTREETECH E3 EZ!
- Wide Application EZ2209 Size: 18.5*19.8 mm, drive current 1.6A, peak current 2A, voltage range12 V- 24 V, 256 subdivision. BTT EZ2209 stepper motor driver can directly use with Mnata E3 EZ and SKR 3 EZ motherboard. EZ2209 can also well-matched with I3 Mega, Octopus V1.2, SKR 3 and other popular main boards by using BTT EZ driver connector.
- Better heat dissipation An innovative 2 in 1 combination of stepper driver and new large aluminum heat sink enables EZ2209 stepper driver better heat dissipation, declining energy consumption to a minimum as well as protecting the driver chip from external damage.
- See more on Amazon...
Brand: BIQU | Manufacturer: BIQU
See On Amazon
Looking For Something Else?
Search