BIGTREETECH TFT35 SPI V2.1 Graphic Smart Display Compatible BTT Manta M8P/M4P/M5P, Manta E3EZ Control Board + CB1 Support Running Klipper Firmware DIY Upgrade 3D Printer
Asin: B0BSCQNF28 | Model: KINGPRINTER-1040000035 | PartNumber: KINGPRINTER-1040000035
As an Amazon Associate we earn a fee from qualifying purchases when you follow a link to Amazon from this page. We rank the products, but the links to Amazon are promotional.3. It Is Connected With The Main Board Through Fpc Cable, Which Is Simple And Convenient To Operate;.
5. Currently, It Only Supports Bigtreetech Cb1. If You Use Cb1 V2.2, You Only Need To Use With Tft35 Spi V2.1; If You Use Cb1 V2.1, You Need To Use With Tft35 Spi V2.1+Io2can V1.0. If You Have Any Questions, You Can Contact Us At Any Time, And We Will Answer Your Questions..
4. Designed With Xh2.54 Terminal, Which Can Communicate With The Board Through The Terminal..
2. Each Motor Drive Shall Select Power Supply, Motor Power Supply Or Main Power Supply (Heating Rod Power Supply) Separately;.
Features
- 1. LCD display adopts SPI, touch adopts I2C communication mode, and shares the main control chip with the motherboard, which greatly reduces the cost of touch screen;
- 2. Each motor drive shall select power supply, motor power supply or main power supply (heating rod power supply) separately;
- 3. It is connected with the main board through FPC cable, which is simple and convenient to operate;
- 4. Designed with XH2.54 terminal, which can communicate with the board through the terminal.
- 5. Currently, it only supports BIGTREETECH CB1. If you use CB1 V2.2, you only need to use with TFT35 SPI V2.1; If you use CB1 V2.1, you need to use with TFT35 SPI V2.1+IO2CAN V1.0. If you have any questions, you can contact us at any time, and we will answer your questions.
- See more on Amazon...
Brand: BIGTREETECH | Manufacturer: BIGTREETECH
See On Amazon Similar To BIGTREETECH TFT35 SPI V2.1 Graphic
#1
BIGTREETECH Pi V1.2 Control board 64bit Quad Core 1GB DDR3L 40-pin GPIO Compatible with SKR MINI E3 V3.0 Octopus/SKR V1.4 turbo to run Klipper/Linux/Debain For I3/CoreXY 3D Printer
Asin: B0C46B6X64 | Model: PI V1.2 | PartNumber: PI V1.2
ăSupport Display And MotherboardăBtt Pi V1.2 Core Board Display Adopts Malig32 Mp2 Gpu,Support Opengl3.2 And Hdmi2.0A Uhd 4K Video & Audio Output And Spi ScreenïŒBtt Hdmi5/7,Tft35 Spi) ,Onboard 4Xusb2.0 Port.Powerful High Performance Details And Clarity. Motherboard Suppport Skr Mini E3 V3.0 ,Skr Pico ,Skr V1.4 Turbo,Skr 3,Kraken,Octopus Pro/Octopus V1.1 Series.Then Running Klipper Firmware..
ăFlexible PowerăSupport Usb-C 5V Power Supply And Dc12v-24V From A 3D Printer,Making It Easy And Efficient To Power Up The Board Without Any Extra Adapters Or Power Soucres..
ăRich ConnectivityăOnboard Standard 40-Pingpio Header,3.5Mm Audio JackïŒTf Card SlotïŒAdxl345 Spi,Usb To Can Module(Need To Purchase Can Adapter V1.0 Module),Built-In Ir Receiver.Rj45 Port Support A 100Mbps Wired Network .Built-In 2.4G Wifi Module ,Supports 100Mbps Wireless Network, Users Can Connect The Inlculde Wifi Antenna To Get A Stronger And More Stable Wifi Signa..
ăAbout SizeăBtt Pi V1.2 Control Board Size Is 85*56Mm,The Same As The Raspberry-Pi 3B/4B, Making It A Seamless Fit For Your Existing Projects..
Features
- Main control chip bigtreetech btt pi v1.2 board adopts ALLWINNER H616,64-bit Quad-core, Cortex-A53@1.5GHz Processor ,RAM is 1GB DDR3L SDRAM.
- About Size BTT PI V1.2 Control Board size is 85*56mm,the same as the Raspberry-Pi 3B/4B, Making it a seamless fit for your existing projects.
- Support Display and Motherboard btt pi v1.2 core board display Adopts MaliG32 MP2 GPU,Support OpenGL3.2 and HDMI2.0A UHD 4K Video & Audio output and SPI screen BTT HDMI5/7,TFT35 SPI) ,onboard 4xUSB2.0 port.Powerful High Performance details and clarity. motherboard suppport SKR MINI E3 V3.0 ,SKR Pico ,SKR V1.4 turbo,SKR 3,Kraken,Octopus pro/Octopus V1.1 series.then running Klipper firmware.
- Rich Connectivity Onboard Standard 40-pinGPIO header,3.5mm Audio Jack TF card Slot ADXL345 SPI,USB To CAN Module(need to purchase CAN Adapter V1.0 module),Built-in IR Receiver.RJ45 port support a 100Mbps wired network .built-in 2.4G Wifi module ,supports 100Mbps wireless network, Users can connect the inlculde wifi antenna to get a stronger and more stable Wifi signa.
- Flexible power Support USB-C 5V power supply and DC12V-24V from a 3D Printer,making it easy and efficient to power up the board without any extra adapters or power soucres.
- See more on Amazon...
Brand: BIGTREETECH | Manufacturer: BIGTREETECH
Dimensions: 0.39 x 3.30 x 2.20 inches
See On Amazon #2
BIGTREETECH Mini12864 V2.0 LCD Graphic Smart Display Control Board with Adapter and Cable for Ender-3 VORON 2.4 Prusa-i3 3D Printer RAMPS 1.4 RepRap 3D Printer Mendel Prusa Arduino
Asin: B08P5LXR86 | Model: KINGPRINT-ZZB000475 | PartNumber: KINGPRINT-ZZB000475 | Ean: 0791568743491 | UPC: 791568743491
3.Product Comes Encoder Parameter Adjustment Can Be Achieved, And The File Selection Print..
5.Do Not Worry About The Problem Of After-Sales, If There Is Any Need, Get In Touch With Us, We Will Help You Solve It..
4.Plug And Play On The Ramps, But Need To Modify The Firmware To Support..
2.With A Sd Card Base On Back, Put Slicing File Into The Sd Card And Select The File On The Lcd, Then Can Be Printing..
Features
- 1.The Mini12864 display panel has RGB multi-color backlight and can support 8 RGB, which is even more cool.
- 2.With a SD card base on back, put slicing file into the SD card and select the file on the LCD, then can be printing.
- 3.Product comes encoder parameter adjustment can be achieved, and the file selection print.
- 4.Plug and play on the RAMPS, but need to modify the firmware to support.
- 5.Do not worry about the problem of after-sales, if there is any need, get in touch with us, we will help you solve it.
- See more on Amazon...
Brand: BIGTREETECH | Manufacturer: BIGTREETECH
Dimensions: 1.18 x 2.36 x 1.18 inches | Weight: 0.11 Pounds
See On Amazon #3
BIGTREETECH SKR Mini E3 V3.0 Control Board +TFT35 E3 V3.0.1 Touch Screen Display 32-Bit Silent Board Integrated with TMC2209 UART Stepper Driver Compatible with Ender 3/5 Ender 3 Pro/V2 3D Printer
Asin: B09MYT45BQ | Model: 1060000518 | PartNumber: 1060000518
âăImpressive Heat DissipationăThe Btt Skr Mini E3 V3.0 Silent Board Also Looks Aesthetic With Upgraded Designs.New Heatsink And 3 Pwm Controlled Fans Serve To Cool Down The Machine During Printing, Effectively Improving Performances On Heat Dissipation. A Direct 3D Printer Control Board Replacement For Ender 3, Ender 3 Pro, And Ender 5 3D Printer Motherboards..
âăSatisfying After-Sales SupportăIf You Have Any Problems About Btt Skr Mini E3 V3.0 & Tft35 E3 V3.0.1 Smart Display Combo Sets, Please Feel Free To Contact Us Anytime. We Have Profession Technical Supports Team To Help You As Soon As We Can..
âăSupports Touch/Graphic DisplayăBtt Tft35-E3 V3.0 Display Enables You To Easily Switch Between The Marlin Lcd Emulator And Touch Screen With Menu Interface, Simply By Pressing And Holding The Selector Wheel. It's A Plug And Play On Ender Series Printers With Btt Skr Mini E3 V3.0 Control Board.ïŒNote:When Running Klipper Firmware,Tft35 E3 V3.0.1 Display Only Support 12864 Mode).
âăUpgraded More CapabilitiesăIntergrated With Tmc2209 V1.3 Mute Stepper Driver,Bigtreetech Skr Mini E3 V3.0 Motherboard Offers Silent Performance As Default, And Supports Dual Z Steppers For Linear Rail And Belt Upgrades, Filament Runout Support, Automatic Shutdown (Ups Support), Power-Off Resume, Sensorless Homing And So On..
Features
- BIGTREETECH Combo Set Comes with Bigtreetech SKR Mini E3 V3.0 32 bit control board and TFT35 E3 V3.0.1 touch screen display with dual modes as a set. perfect for Ender 3 3D Printer,plug and playing, Adopted the latest G0 series MCU-STM32G0B0RET6 main control chip packing excellent performances.
- Upgraded More Capabilities Intergrated with TMC2209 V1.3 mute stepper driver,BIGTREETECH SKR Mini E3 V3.0 motherboard offers silent performance as default, and supports dual Z steppers for linear rail and belt upgrades, filament runout support, automatic shutdown (UPS support), power-off resume, sensorless homing and so on.
- Impressive Heat Dissipation The BTT SKR MINI E3 V3.0 silent board also looks aesthetic with upgraded designs.New heatsink and 3 PWM controlled fans serve to cool down the machine during printing, effectively improving performances on heat dissipation. A direct 3D printer control board replacement for Ender 3, Ender 3 Pro, and Ender 5 3D Printer motherboards.
- Supports Touch/Graphic Display btt tft35-e3 v3.0 display enables you to easily switch between the Marlin LCD emulator and touch screen with menu interface, simply by pressing and holding the selector wheel. It's a plug and play on Ender series printers with BTT SKR MINI E3 V3.0 control board. Note:When running klipper firmware,tft35 e3 v3.0.1 display only support 12864 mode)
- Satisfying After-Sales Support If you have any problems about BTT SKR MINI E3 V3.0 & TFT35 E3 V3.0.1 smart display combo sets, please feel free to contact us anytime. We have profession technical supports team to help you as soon as we can.
- See more on Amazon...
Brand: BIGTREETECH | Manufacturer: BIGTREETECH
See On Amazon #4
BIGTREETECH DIRECT SKR Mini E3 V2.0 Control Board 32Bit Silent Motherboard Integrated with TMC2209 UART Stepper Motor Driver for Upgraded Ender 3 Ender 3 Pro 3D Printer Control Board
Asin: B089CQ3DHB | Model: ZZB000412 | PartNumber: ZZB000412
đăSupport Various FunctionsăBtt Skr Mini E3 V2.0 Control Board Supports Various Function Extensions, Such As, Bltouch, Filament Detection, Resumption Of Shutdown, Shutdown After Shutdown, Etc ..
đăSatisfying Customer ServicesăIf You Need Any Information For Skr Mini E3 V2.0, You Could Contact Us On Amazon, And We'll Get Back To You Within 24 Hours..
đăNotesă Pay Attention To Correct Wiring, Avoid Motherboard Contact With Metal Objects, And Take Electrostatic Protection Measures..
đă 4 Layers For BoardăBigtreetech Direct Skr Mini E3 V2.0 Increased To 4 Layers On The Control Board's Back, So As To Improve On Heat Dissipation Signal Function And Anti-Interference..
đăBetter Thermal DissipationăThe Hot-Bed Mos Tube Uses Wsk220n04, Low On-Resistance, Which Reduces Heat Generation. Enlarged Heat Dissipation Area Protects Driving Chip And Components From Problems Caused By Heat Sink..
Features
- Silent Control Board BIGTREETECH DIRECT SKR MINI E3 V2.0 adopts ARM Cortex-M3 series STM32F103RCT6 main control chip with 32-bit CPU 72MHz, integrated with TMC2209 to enhance its stability. It's a super easy drop in replacement for Ender 3 printer.plug and playing.
- Better Thermal Dissipation The hot-bed MOS tube uses WSK220N04, low on-resistance, which reduces heat generation. Enlarged heat dissipation area protects driving chip and components from problems caused by heat sink.
- Support Various Functions BTT SKR MINI E3 V2.0 control board supports various function extensions, such as, BLtouch, filament detection, resumption of shutdown, shutdown after shutdown, etc .
- 4 Layers for Board BIGTREETECH DIRECT SKR MINI E3 V2.0 increased to 4 layers on the control board's back, so as to improve on heat dissipation signal function and anti-interference.
- Satisfying Customer Services If you need any information for SKR MINI E3 V2.0, you could contact us on Amazon, and we'll get back to you within 24 hours.
- Notes Pay attention to correct wiring, avoid motherboard contact with metal objects, and take electrostatic protection measures.
- See more on Amazon...
Brand: BIGTREETECH | Manufacturer: BIGTREETECH Origianl
Dimensions: 0.39 x 4.00 x 2.80 inches
See On Amazon #5
BIGTREETECH Upgrade PI TFT50 V2.1 TFT LCD Display DSI 800x480 for Raspberry Pi 4 3 2 Model B RPi 1 B B+ A A+ 3D Printer Controller (5in Capacitive Touch Screen)
Asin: B08FD2YZ23 | Model: ZZB000417 | PartNumber: ZZB000417 | Ean: 0779303890068 | UPC: 779303890068
†ă5-Point Touchă It Supports Raspberry Pi Dsi Display Interface, Comes With A Capacitive Touch Panel, And Supports 5-Point Touch.Capacitive Touch Control ,Better Touch Response,Faster Response Time..
â€ă12 Months WarrantyăThank You Very Much For Your Choice And Trust. If You Have Any Questions About The Product, Can You Contact Us First? Give Us The Opportunity To Understand Your Needs, And We Will Do Our Best To Answer Questions And Solve Problems For You..
†ăEasy To InstallăThe Unique Hole Design On The Back Allows You To Install The Raspberry Pi Directly.The Display Adopts Raspberry Pi Power Supply Design, Without External Power Supply..
â€ăHigh ResolutionăThis 5 Inch Lcd Touch Screen With A Resolution Of 800*480 And A Display Area Of 108X64.8Mm..
Features
- Wide range of applications 5 inch capacitive Touch Screen designed for for pi 4 model B /pi 3 model A+ B+ B/pi 2 model B/pi 1 model B+ A+.
- High resolution This 5 inch LCD touch screen with a resolution of 800*480 and a display area of 108x64.8mm.
- 5-point touch It Supports Raspberry Pi DSI display interface, comes with a capacitive touch panel, and supports 5-point touch.Capacitive Touch Control ,better touch response,faster response time.
- Easy to install The unique hole design on the back allows you to install the Raspberry Pi directly.The display adopts Raspberry Pi power supply design, without external power supply.
- 12 MONTHS WARRANTY Thank you very much for your choice and trust. If you have any questions about the product, can you contact us first? Give us the opportunity to understand your needs, and we will do our best to answer questions and solve problems for you.
- See more on Amazon...
Brand: BIQU | Manufacturer: BIGTREETECH
See On Amazon #6
BIGTREETECH Direct Relay V1.2 Automatic Shutdown Module After Printing Support Resume Printing While Power Off for SKR Mini E3 V3.0 Octopus V1.1 Manta M4P/M5P/M8P/SKR V1.4 Turbo Ender 3 3D Printer
Asin: B07QJ4MZVN | Model: ZZB000239 | PartNumber: ZZB000239 | Ean: 0778601687363 | UPC: 778601687363
Bigtreetech Relay V1.2 Is Easy To Understand, Its Logo Is Clearly Visible And Its Function Is Practical..
Btt Relay V1.2 Compatible With Bigtreetech Skr Mini E3 V3.0/Skr Mini E3 V2.0/Skr V1.4 Turbo/Manta M4p/Mp/M8p/Octopus Pro/Octopus V1.1/Mks Gen L ...3D Printer Control Board.
The Function Is To Automatically Detect Whether The 3D Printing Of The Project Printer Is Completed. When It Is Detected That The Project Is Printed, The Power Can Be Automatically Turned Off. The Goal Is To Create An Automated 3D Printing Environment With Low Carbon Content, Environmental Protection, Energy Savings And Reduced Consumption..
Features
- BIGTREETECH Relay V1.2 module is the first automatic shutdown module independently developed by BIGTREETECH Tecnologia.
- The function is to automatically detect whether the 3D printing of the project printer is completed. When it is detected that the project is printed, the power can be automatically turned off. The goal is to create an automated 3D printing environment with low carbon content, environmental protection, energy savings and reduced consumption.
- BIGTREETECH relay V1.2 is easy to understand, its logo is clearly visible and its function is practical.
- BTT Relay V1.2 Compatible with BIGTREETECH SKR MINI E3 V3.0/SKR MINI E3 V2.0/SKR V1.4 Turbo/Manta M4p/MP/M8P/Octopus pro/Octopus V1.1/MKS GEN L ...3D Printer Control board
- See more on Amazon...
Brand: BIGTREETECH Direct | Manufacturer: BIGTREETECH DIRECT
See On Amazon #7
BIGTREETECH TFT35 V3.0.1 Touch Screen Display with Two working Modes Smart Controller Panel Compatible with LCD12864 WiFi for Octopus V1.1/ SKR V1.4 turbo/SKR 3/Manta M4P/M5P SKR Pro Ender3 3D Printer
Asin: B07VWGFKLZ | Model: K-03101171 | PartNumber: K-03101171 | Ean: 0778365968586 | UPC: 778365968586
â»ăMore Reserved Extensionsă :Tft35 V3.0.1 Touch Screen Reserves The Extension Ports Of Filament Break Detection, Automatic Shutdown After Printing, Also Wifi Function Can Be Realized By External Wifi Module Through Wifi Port. Compatible With Skr Mini E3 V3.0/Skr V1.4 Turbo/Octopus/Skr 3/Skr 3 Ez/Manta M4p/5P/8P Control Board.
â»ă100% Technical Supportsă: If You Have Any Problems About Btt Tft35 V3.0.1 Touchscreen, Please Feel Free To Contact Us On Amazon. Our Technical Supports Team Will Respon To You Within 24 Hours. 1-Year Warranty Is 100% Guaranteed!.
â»ăEasy Firmware Updatesă: It Is Easy And Convenient To Update Firmware By Sd Card, Simply Downloading From Github, Coping And Saving It To Sd Card. Firmware Must Be Reserved, Then Re-Plug The Sd Card And Wait To 10S. That's All Takes To Finish Updating On Firmware..
â»ăDual Working Modesă: Btt Tft35 V3.0.1 Display Enables Two Different Modes, With Options For Either Lcd12864 Encoder Mode, Or The Modern Colour Touch Screen Style. It Also Supports Both Sd Card And Usb Stick Printing..
Features
- 32 Bit Microprocessor : bigtreetech tft35 v3.0.1 display Adopted ARM Cortex-M3 series GD32F205VCT6 master controller chip with 32-bit CPU main frequency of 120 MHz, BTT TFT35 V3.0.1 touch screen can perfectly replace the LCD12864 screen for use.
- Dual Working Modes : BTT TFT35 V3.0.1 display enables two different modes, with options for either LCD12864 Encoder Mode, or the modern Colour Touch Screen Style. It also supports both SD card and USB stick printing.
- More Reserved Extensions :TFT35 V3.0.1 touch screen reserves the extension ports of filament break detection, automatic shutdown after printing, also WIFI function can be realized by external WIFI module through WIFI port. compatible with SKR MINI E3 V3.0/SKR V1.4 Turbo/Octopus/SKR 3/SKR 3 EZ/Manta M4P/5P/8P Control board
- Easy Firmware Updates : It is easy and convenient to update firmware by SD card, simply downloading from Github, coping and saving it to SD card. firmware must be reserved, then re-plug the SD card and wait to 10s. That's all takes to finish updating on firmware.
- 100% Technical Supports : If you have any problems about BTT TFT35 V3.0.1 touchscreen, please feel free to contact us on Amazon. Our technical supports team will respon to you within 24 hours. 1-Year Warranty is 100% guaranteed!
- See more on Amazon...
Brand: BIGTREETECH | Manufacturer: BIGTREETECH Direct
See On Amazon #8
DSD TECH 1.8 Inch TFT LCD Display Module with SPI Interface for Arduino and MCU
Asin: B07WDJ3TV6 | Ean: 0734678383188 | UPC: 734678383188
Support 16Bit Rgb 65K Color Display, 128X160 Resolution, St7735s Driver Chip, Working Voltage Is 5V/3.3V, Weight Is 15G.
Dsd Tech Offer A One-Year Warranty And Lifetime Technical Support For This Module. If You Have Any Questions, Please Feel Free To Contact Us! We Will Respond To You Within 24 Hours..
Dsd Tech Provides Sample Code For The Arduino For This Tft Lcd. With The Sample Code, You Can Use This Lcd Screen In 10 Minutes..
The Tft Lcd Display Can Be Directly Inserted Into Arduino, Which Is Convenient And Quick. Using Spi Communication Mode, Only 4 Ios Are Needed To Illuminate The Display, And The Sd Card Slot Is Convenient For Function Expansion..
Features
- This is a 1.8 inch color screen that can display fullcolors, suitable for electronic enthusiasts and students to use in development boards such as arduino and raspberry pi.
- The TFT LCD display can be directly inserted into arduino, which is convenient and quick. Using SPI communication mode, only 4 IOs are needed to illuminate the display, and the SD card slot is convenient for function expansion.
- Support 16BIT RGB 65K color display, 128X160 resolution, ST7735s driver chip, working voltage is 5V/3.3V, weight is 15g
- DSD TECH provides sample code for the Arduino for this TFT LCD. With the sample code, you can use this LCD screen in 10 minutes.
- DSD TECH offer a one-year warranty and lifetime technical support for this Module. If you have any questions, please feel free to contact us! We will respond to you within 24 hours.
- See more on Amazon...
Brand: DSD TECH | Manufacturer: DSD TECH
Dimensions: 0.98 x 2.76 x 1.57 inches | Weight: 0.03 Pounds
See On Amazon #9
BIGTREETECH Octopus V1.1 Control Board 32bit Compatible TFT Series Screen, Support DIY Klipper Firmware and Raspberry-Pi Online Printing for Voron V2.4 Upgrade 3D Printer (with 8Pcs TMC2209)
Asin: B09713SRVP | Model: KINGPRINTER-UUU001949 | PartNumber: KINGPRINTER-UUU001949
đăMotherboard Expansion FunctionăSupport Bltouch, Locked-Rotor Detection, Shutdown After Printing, Resume Printing After Power Failure, Can Bus, U Disk Function, Iic Expansion; At The Same Time Reserved Wifi Interface, Pt100 Thermistor Interface (Optional), Dual Z-Axis Printer..
đăTmc2209 Driver ModeăTmc Motor Drivers Can Be Used In Spi Or Uart Mode By Simply Adjusting The Onboard Jumpers Beneath Each Motor Driver. Additionally You Can Connect Or Disconnect The Tmc Diag Pin Using An Onboard Jumper Allowing You To Use Hard Endstops Or Sensorless Homing Without The Need To Cut Any Pins..
đăTmc2209 Driver FeaturesăThe Tmc2209 Stepper Driver Is Not Easy To Lose Steps And Is In An Ultra-Quiet Mode; The Module Has A Large Area Of Heat Dissipation Pad, Which Can Reduce The Temperature Of The Driver When It Is Working; The Module Supports Three Modes: Step / Dir And Uart..
đăStrong Diy SupportăThis Motherboard Supports Up To 8 Stepper Drivers With 9 Stepper Driver Outputs In Total; And Up To 6 Pwm Fans And 2 Always-On Fans With The Ability To Individually Select The Voltage Rail That Will Drive Each Fan. Select From Vin, 12V Or 5V..
Features
- Main Control Chip Uses a 32-bit ARM Cortex-M4 series STM32F446ZET6 main control chip with a core frequency of 180MHz.
- Strong DIY Support This motherboard supports up to 8 stepper drivers with 9 stepper driver outputs in total; And up to 6 PWM fans and 2 always-on fans with the ability to individually select the voltage rail that will drive each fan. Select from Vin, 12V or 5V.
- Motherboard Expansion Function Support BLTouch, locked-rotor detection, shutdown after printing, resume printing after power failure, CAN bus, U disk function, IIC expansion; at the same time reserved WIFI interface, PT100 thermistor interface (optional), dual Z-axis printer.
- TMC2209 Driver Features The TMC2209 stepper driver is not easy to lose steps and is in an ultra-quiet mode; the module has a large area of heat dissipation pad, which can reduce the temperature of the driver when it is working; the module supports three modes: STEP / DIR and UART.
- TMC2209 Driver Mode TMC Motor drivers can be used in SPI or UART mode by simply adjusting the onboard jumpers beneath each motor driver. Additionally you can connect or disconnect the TMC DIAG pin using an onboard jumper allowing you to use hard endstops or sensorless homing without the need to cut any pins.
- See more on Amazon...
Brand: BIGTREETECH | Manufacturer: BIGTREETECH
See On Amazon #10
BIGTREETECH SKR V1.4 Control Board 32bit Upgrade SKR V1.3 Motherboard, Compatible TFT35/TFT35 E3/TFT70 Touch Screen Mini12864 LCD Support TMC2209/EZ2209/TMC2208/TMC5160 for Most FDM 3D Printer
Asin: B0BHNVFR1M | Model: KINGPRINTER-1020000399 | PartNumber: KINGPRINTER-1020000399
âSupport 2.4, 2.8, 3.5-Inch Color Touch Screen, Support Lcd2004 Screen, Lcd12864 Screen; Upgrade Configuration Firmware Through Sd Card, Simple, Convenient And Efficient Operation..
âOn-Board Tmc Driver Spi Working Mode And Uart Working Mode, And The On-Board Diag Function Pins Are Convenient For Customers To Use, Eliminating The Complicated Wiring Process, Which Can Be Used By Simply Removing And Inserting The Jumper Cap; Functions Such As Continuous Power On, Material Detection, Shutdown After Power Off..
âIt Can Supply Power To Tft Screen, Bltouch, Neo-Pixel By Plugging In An External Dc5v Power Module; In Addition, I2c, Spi, Wifi Interface Is Reserved To Facilitate Customer Diy..
âEquipped With Highly Modular Open Source Firmware Marlin 2.0, Which Is Convenient For Users To Diy And Secondary Development..
Features
- Using 32-bit 100MHz ARM-class Cortex-M3 series LPC1768 main control chip, the performance is greatly improved.
- Equipped with highly modular open source firmware Marlin 2.0, which is convenient for users to DIY and secondary development.
- Support 2.4, 2.8, 3.5-inch color touch screen, support LCD2004 screen, LCD12864 screen; Upgrade configuration firmware through SD card, simple, convenient and efficient operation.
- It can supply power to TFT screen, BLtouch, Neo-pixel by plugging in an external DC5V power module; in addition, I2C, SPI, WIFI interface is reserved to facilitate customer DIY.
- On-board TMC driver SPI working mode and UART working mode, and the on-board DIAG function pins are convenient for customers to use, eliminating the complicated wiring process, which can be used by simply removing and inserting the jumper cap; Functions such as continuous power on, material detection, shutdown after power off.
- See more on Amazon...
Brand: BIGTREETECH | Manufacturer: BIGTREETECH
See On Amazon #11
BIGTREETECH SKR Mini E3 V3.0 Control Board + TFT35 E3 V3.0.1 Graphic Smart Display Panel Board New Upgrade 3D Printer Parts for Ender 3, Ender3 Pro, Ender 3 V2
Asin: B09LCKPV4G | Model: SKR Mini E3 V3.0+TFT35 E3 V3.0.1 | PartNumber: SKR Mini E3 V3.0+TFT35 E3 V3.0.1
ăIncreased Heat SinkăRedesign The Drive Heat Sink, Strengthen The Drive Heat Dissipation Capacity, And Greatly Improve The Heat Dissipation Performance;.
ăTft35-E3 V3.0 Screenă This Touch Screen Panel Board Has Higher Compatibility. Users Can Select Two Work Modes:Uart Serial Port Screen Mode And 12864 Screen Mode;Serial Port Screen Mode Supports Two Printing Modes: Sd Card And U Disk..
ăOutput Power SupplyăIncrease Spi Output Port +3.3V Power Supply, External Spi Sensor Power Supply Voltage +3.3V And +5V Are Optional, Support The Motherboard To Directly Supply Power To Peripherals..
ăThree Cnc FanăIncrease The Heat Dissipation Controllable Fan To Reduce The Printer Temperature When The Device Is Working;.
Features
- Main Control Chip Adopt STMicroelectronics' latest G0 series main control chip STM32G0B1RET6 or STM32G0B0RET6;
- Three CNC Fan Increase the heat dissipation controllable fan to reduce the printer temperature when the device is working;
- Increased Heat Sink Redesign the drive heat sink, strengthen the drive heat dissipation capacity, and greatly improve the heat dissipation performance;
- Output Power Supply Increase SPI output port +3.3V power supply, external SPI sensor power supply voltage +3.3V and +5V are optional, support the motherboard to directly supply power to peripherals.
- TFT35-E3 V3.0 Screen This touch screen panel board has higher compatibility. Users can select two work modes:UART serial port screen mode and 12864 screen mode;Serial port screen mode supports two printing modes: SD card and U disk.
- See more on Amazon...
Brand: BIGTREETECH | Manufacturer: BIGTREETECH
See On Amazon #12
BIGTREETECH Direct ESP8266EX ESP01S Serial Wireless Module WiFi Sensor (ESP01 Updated) WiFi Module DIY for SKR PRO V1.1 SKR Mini E3 TFT24 TFT35 V3.0 Screen
Asin: B081DRXXN2 | Ean: 0787794452481 | UPC: 787794452481
Data Interface: Uart / Hspi / I2c / I2s / Ir Remote Contorl / Gpio / Pwm.
Working Current: Average 80Ma.
Operating Voltage: 3.0 ~ 3.6V (Suggest 3.3V).
Frequency Range: 2.4Ghz~2.5Ghz(2400M ~ 2483.5M).
Features
- Wireless standard: 802.11 b / g / n
- Frequency range: 2.4GHz~2.5GHz(2400M ~ 2483.5M)
- Data interface: UART / HSPI / I2C / I2S / IR Remote Contorl / GPIO / PWM
- Operating voltage: 3.0 ~ 3.6v (Suggest 3.3v)
- Working current: average 80mA
- See more on Amazon...
Brand: BIGTREETECH DIRECT | Manufacturer: BIGTREETECH DIRECT
Weight: 0.00 Pounds
See On Amazon #13
BIGTREETECH SKR Mini E3 V3.0 + BTT Pi V1.2 + TFT35 SPI V2.1 + SFS V2.0 Kit for FDM 3D Printer Upgrade Klipper Firmware for Ender-3, Ender-3 V2, Voron 2.4, Most of i3/Core XY 3D Printer
Asin: B0CHMFG9KF
The Btt Pi Is Equipped With Quad Core 64 Bit Arm Cortex-A53 @ 1.5Ghz Processor, 1Gb Ddr3 Memory Chip, With Powerful Performance. Reserve Spi Port, Adxl345 Port, Usb To Can Module(Need To Purchase U2c Module) To Enhance Diy Performance..
Thr Sfs V2.0 Detects Extrusion Errors Caused By Filament Runout, Nozzle Clogging, Filament Tying, And Extruder Trouble. It Has Two Signal Outputs And Indicator Lights To Distinguish Between Clogging Or Filament Runout. Small And Lightweight, It Will Not Add Too Much Pressure To The Printer's Extrusion Head..
The Tft35 Spi Lcd Display Adopts Spi, And The Touch Screen Adopts I2c Communication Mode; It Can Be Connected To The Motherboard Through Fpc Cable, Making The Operation Simple And Convenient; Adopting Xh2.54 Terminal Design, It Can Communicate With A Single Board Through Terminals..
The Skr Mini E3 V3.0 Adopts Stmicroelectronics' Latest G0 Series Main Control Chip Stm32g0b1ret6 Or Stm32g0b0ret6; Adding Controllable Cooling Fans And Upgrading Drive Heat Sink Effectively Reduces The Temperature During 3D Printing Work..
Features
- This kit includes BIGTREETECH SKR Mini E3 V3.0, BTT Pi V1.2, TFT35 SPI V2.1, Smart Filament Runout Sensor V2.0, which can upgrade klipper firmware for i3 and CoreXY 3D printers.
- The SKR Mini E3 V3.0 adopts STMicroelectronics' latest G0 series main control chip STM32G0B1RET6 or STM32G0B0RET6; Adding controllable cooling fans and upgrading drive heat sink effectively reduces the temperature during 3d printing work.
- The BTT Pi is equipped with quad core 64 bit ARM Cortex-A53 @ 1.5GHz processor, 1GB DDR3 memory chip, with powerful performance. Reserve SPI port, ADXL345 port, USB To CAN module(need to purchase U2C module) to enhance DIY performance.
- The TFT35 SPI LCD display adopts SPI, and the touch screen adopts I2C communication mode; It can be connected to the motherboard through FPC cable, making the operation simple and convenient; Adopting XH2.54 terminal design, it can communicate with a single board through terminals.
- Thr SFS V2.0 detects extrusion errors caused by filament runout, nozzle clogging, filament tying, and extruder trouble. It has two signal outputs and indicator lights to distinguish between clogging or filament runout. Small and lightweight, it will not add too much pressure to the printer's extrusion head.
- See more on Amazon...
Brand: BIGTREETECH | Manufacturer: BIGTREETECH
See On Amazon #14
BIGTREETECH TFT35 V3.0.1 Graphic Smart Display Controller Board for 3D Printer Ramps 1.4 RepRap 3D Printer Can Select Two Work Modes
Asin: B07VWF4W3J | Model: TFT35 V3.0.1 | PartNumber: TFT35 V3.0.1 | Ean: 0778601687783 | UPC: 778601687783
3.Reserve Wifi Port, And Wifi Function Is Realized By External Wifi Module;.
5.2 Sets Of Uart Serial Port Extension Ports Are Reserved For Diy Use..
4.Reserve The Extension Port Of Filament Breaking Detection (Fil-Det);Reserve The Extension Port Of Automatic Shutdown After Printing (Ps-On);.
2.Serial Port Screen Mode Supports Two Printing Modes: Sd Card And U Disk..
Features
- 1.Upgrade the firmware by SD card. It is easy and convenient to operate.This display board has higher compatibility. Users can select two work modes,they are UART serial port screen mode and 12864 screen mode.
- 2.Serial port screen mode supports two printing modes: SD card and U disk.
- 3.Reserve WIFI port, and WIFI function is realized by external WIFI module;
- 4.Reserve the extension port of filament breaking detection (FIL-DET);Reserve the extension port of automatic shutdown after printing (PS-ON);
- 5.2 sets of UART serial port extension ports are reserved for DIY use.
- See more on Amazon...
Brand: BIGTREETECH | Manufacturer: BIGTREETECH
See On Amazon #15
BIGTREETECH SKSM V1.0 SBC Power Protection Module with Current Limiting Protection, Smart Power Outage Detection Compatilbe with Raspberry Pi3, 4B, BTT PI, PI4B+CB1 Core Board Running Klipper
Asin: B0D2HNZXLL | Model: BIGTREETECH SKSM V1.0 | PartNumber: BIGTREETECH SKSM V1.0
â
Current Limiting Protection: Sksm Power Shutdown Protection Module With The Current-Limiting Protection Function, It Can Limit The Power Supply Current Of The 3D Printer Motherboard To The Module, Ensure That The Module Will Not Fail To Start Due To Over-Current Protection..
â
Backup Power: Equipped With Two 2.7V 20F Super Capacitors, It Ensures Your Printer Has Enough Power To Save Your Work During An Outage. Comes With Reverse Polarity Protection To Safeguard Against Wrong Connections, Thus Protecting Your PrinterâS Circuit Board..
Note: Sksm Cannot Restart Btt Pi V1.2 Cb1 V2.2 And Manta Series Motherboards Because The Reset Io Is Not Lead Out And Can Only Be Used For Shutdown Protection And Cannot Achieve Self-Starting After Power Failure. If You Have Any Problems, Please Contact With Us, We Will Help You Solve It..
â
Smart Power Outage Detection: It Has A High-Sensitivity Mcu Chip That Can Quickly Detect Power Losses. Small Size, Easier Installation..
â
Power Supply For Raspberry Pi: The Usb-A Port On The Sksm Directly Powers Raspberry Pi3, 4B, Btt Pi And Pi4b Adapter+Cb1/Cb2, Offering A 5V 2A Output, For Running Klipper Dc24 3D Printer..
Features
- SBC System Image Protection: BIGTREETECH SKSM V1.0 module designed for Klipper, the SBC can easily be supplied with additional power after the printer is turned of, allowing files to be saved securely before shutdown, thus protecting the SBC system image from damage.
- Power Supply for Raspberry Pi: The USB-A port on the SKSM directly powers Raspberry Pi3, 4B, BTT PI and Pi4B Adapter+CB1/CB2, offering a 5V 2A output, for running Klipper DC24 3D Printer.
- Current Limiting Protection: SKSM power shutdown protection module with the current-limiting protection function, It can limit the power supply current of the 3D printer motherboard to the module, ensure that the module will not fail to start due to over-current protection.
- Smart Power Outage Detection: It has a high-sensitivity MCU chip that can quickly detect power losses. small size, easier installation.
- Backup Power: Equipped with two 2.7V 20F super capacitors, it ensures your printer has enough power to save your work during an outage. comes with reverse polarity protection to safeguard against wrong connections, thus protecting your printer s circuit board.
- Note: SKSM cannot restart BTT Pi v1.2 CB1 V2.2 and Manta series motherboards because the reset IO is not lead out and can only be used for shutdown protection and cannot achieve self-starting after power failure. If you have any problems, please contact with us, we will help you solve it.
- See more on Amazon...
Brand: BIGTREETECH Direct | Manufacturer: BIGTREETECH Direct
See On Amazon #16
BIGTREETECH TFT35 SPI V2.1 Touch Screen Display 3.5 Inches Smart Controller Panel Use with CB1 + BTT Manta E3EZ / Manta M8P / Manta M4P / Manta M5P to Run Klipper
Asin: B0BRZ4RL1P
đăReserved Extension PortsăDesigned With Xh2.54 Terminal, Which Can Communicate With The Board Through The Terminal..
đăQuality WarrantyăWe Offer A 12 Months Quality Warranty Period For Our Products. If You Have Any Question And Feedback Please Feel Free To Contact Us, Our Professional Technical Team Will Try Best To Help You..
đăCompatible With Btt Cb1ăTft35 Spi Touch Screen Is Compatible With All Versions Of Btt Cb1 Core Board. It Can Directly Use With Cb1 V2.0 And Cb1 V2.2, And Need To Match Up With Io2can Expansion Module When Used With Cb1 V2.1..
đăResponsive & Easy OperationăTft35 Spi Is A 3.5 Inch Full-Color Screen With Ultra Clear Display And Responsive Touch. It Is Connected To The Motherboard Through The Fpc Cable, Simple And Convenient To Use, Greatly Improving Your Klipper Experience..
Features
- TFT35 SPI Touch Screen BIGTREETECH TFT35 SPI display is a resistive touch screen that controlled by the motherboard chip. Its LCD display is supported by SPI and touch function is supported by I2C. Appearance size: 98*56mm, power input : 5V.
- Responsive & Easy Operation TFT35 SPI is a 3.5 inch full-color screen with ultra clear display and responsive touch. It is connected to the motherboard through the FPC cable, simple and convenient to use, greatly improving your klipper experience.
- Reserved Extension Ports Designed with XH2.54 terminal, which can communicate with the board through the terminal.
- Compatible with BTT CB1 TFT35 SPI touch screen is compatible with all versions of BTT CB1 core board. It can directly use with CB1 V2.0 and CB1 V2.2, and need to match up with IO2CAN expansion module when used with CB1 V2.1.
- Quality Warranty We offer a 12 months quality warranty period for our products. If you have any question and feedback please feel free to contact us, our professional technical team will try best to help you.
- See more on Amazon...
Brand: BIQU | Manufacturer: BIQU
See On Amazon #17
BIGTREETECH PITFT50 V2.1 Touch Screen 5inch LCD Display Capacitive DSI 800x480 Upgraded 5 Point Touch for Raspberry Pi A/A+/B/B+/2B/2B+/3B/3B+/4B, BTT PI2/CB2
Asin: B08F1WMQ1J | Model: 1 | PartNumber: 1 | Ean: 0779605889784 | UPC: 779605889784
đăEasy To Adjustă: Btt Pi Tft50 V2.1 Touch Screen The Switch At The Top Flips The Orientation Of The Screen Horizontally Without Any Software Modifications. So Does The Potentiometer Behind The Screen, Which Serves To Adjust The Backlight Brightness..
đă100% Satisfying Customer Servicesă: If You Have Any Problems About Btt Pitft50 V2.1 Lcd Touch Screen, Please Feel Free To Contact Us. Our Professional Technical Supports Are There To Help. 1-Year Warranty Is 100% Guaranteed..
đăFits Raspberry Pi Perfectlyă: Bigtreetech Pi Tft50 Adapt To The Raspberry-Pi Dsi Display Interface, Directly Driven By Dsi; The Unique Hole Design On The Back Allows You To Install The Raspberry-Pi Directly. Pi Tft50 V2.1 Display Adopts Raspberry-Pi Power Supply Design, No External Power Supply Is Needed. It's Designed For Pi 4 Type B / Pi 3 Type A + B + B / Pi 2 Type B / Pi 1 Type B + A + Design, But Doesn't Support Zero Version Of Raspberry Pi..
đăSupports 5-Point Capative Touchă: Featured With Capacitive Touch Panel, Bigtreetech Pitft50 V2.1 Lcd Press Screen Supports 5-Point Touch, Meaning That You Can Touch 5 Parts Of The Screen At The Same Time, And All The Touches Are Responsive And Accurate In The Meanwhile..
Features
- High Resolution : Featured with resolution 800*480, BIGTREETECH PITFT50 V2.1 touch screen 5 inch has display area of 108 x 64.8mm for Raspberry Pi, which gives you easy access to the files available on the SD card inserted in the printer, or the files available in OctoPrint. Support Klipper touch mode.
- Supports 5-Point Capative Touch : Featured with capacitive touch panel, BIGTREETECH PITFT50 V2.1 LCD press screen supports 5-point touch, meaning that you can touch 5 parts of the screen at the same time, and all the touches are responsive and accurate in the meanwhile.
- Easy to Adjust : BTT PI TFT50 V2.1 touch screen the switch at the top flips the orientation of the screen horizontally without any software modifications. So does the potentiometer behind the screen, which serves to adjust the backlight brightness.
- Fits Raspberry Pi Perfectly : BIGTREETECH PI tft50 adapt to the Raspberry-Pi DSI display interface, directly driven by DSI; The unique hole design on the back allows you to install the Raspberry-Pi directly. PI TFT50 V2.1 display adopts Raspberry-Pi power supply design, no external power supply is needed. It's designed for pi 4 type B / pi 3 type A + B + B / pi 2 type B / pi 1 type B + A + design, but doesn't support Zero version of Raspberry Pi.
- 100% Satisfying Customer Services : If you have any problems about BTT PITFT50 V2.1 LCD touch screen, please feel free to contact us. Our professional technical supports are there to help. 1-Year Warranty is 100% guaranteed.
- See more on Amazon...
Brand: BIGTREETECH | Manufacturer: BIGTREETECH Direct
Dimensions: 0.39 x 4.76 x 2.99 Inches | Weight: 0.40 ounces
See On Amazon #18
BIGTREETECH TFT35 V3.0.1 Touch Screen Display RepRap Smart Controller Panel 2 Working Modes Compatible with SKR V1.4/SKR 2 3D Printer Parts
Asin: B07W1PB11F | Model: EE0310117120190731 | PartNumber: EE0310117120190731 | Ean: 0791300548353 | UPC: 791300548353
â€ă12864Lcd ModeăThe 12864Lcd Mode Includes Exp1, Exp2, Exp3, Where Exp1 And Exp2 Are General Motherboards Lcd Screen Interface, While Exp3 Is The Lcd Screen Interface Used By E3 Series Boards (Like Skr Mini E3,Skr E3 Dip, Etc.).
â€ăFirmware Updateă It Is Easy And Convenient To Update Firmware By Sd Card,Download From Our Github, Copy And Save It To Sd Card.Firmware Must Bed Reserved ,Then Re-Plug The Sd Card And Wait To 10S.The Firmware Has Been Successfully Updated..
â€ăMore Extension Ports Is Reservedă Tft35 V3.0.1 Display Reserve The Extension Port Of Filament Break Detection ,Automatic Shutdown After Printing,Also Wifi Function Can Be Realized By External Wifi Module Through Wifi Port..
â€ăTwo Working ModesăTft35 V3.0.1 Touch Screen Support Uart Serial Port Screen Mode(Touch Screen Mode) And 12864 Screen Mode,Serial Screen Mode Supports Both Sd Card And Usb Stick Printing..
Features
- 32 Bit High Performance Microprocessor TFT35 V3.0.1 touch screen uses 32 bit ARM level Cortex-M3 series GD32F205VCT6,120MHz frequency Microprocessor, which makes it an upgraded replacement of LCD12864
- Two Working Modes TFT35 V3.0.1 Touch screen support UART serial port screen mode(touch screen mode) and 12864 screen mode,serial screen mode supports both SD card and USB stick printing.
- 12864LCD Mode The 12864LCD mode includes EXP1, EXP2, EXP3, where EXP1 and EXP2 are general motherboards LCD screen interface, while EXP3 is the LCD screen interface used by E3 series boards (like SKR MINI E3,SKR E3 DIP, etc.)
- More Extension Ports is Reserved TFT35 V3.0.1 display reserve the extension port of filament break detection ,automatic shutdown after printing,also WIFI function can be realized by external WIFI module through WIFI port.
- Firmware Update It is easy and convenient to update firmware by SD card,download from our github, copy and save it to SD card.firmware must bed reserved ,then re-plug the SD card and wait to 10s.The firmware has been successfully updated.
- See more on Amazon...
Brand: BIQU | Manufacturer: BIQU
See On Amazon #19
Woedpez BIGTREETECH BTT EXP-MOT V1.0 Driver Expansion Module for SKR V1.4 Turbo SKR SKR V1.3 Motherboard 3D Printer Parts Bigtreetech Module
Asin: B0CKLNSW4X | Ean: 7551391604986
Number Of For Module Expansion: 3..
Input Power: Dc12v /Dc24v..
Voltage: Dc3.3V /Dc5v..
Driver Mode Optional: Step/Dir,Uart,Spi..
Features
- Product name: EXP-MOT V1.0 module.
- Driver Mode Optional: STEP/DIR,UART,SPI.
- Number of for module expansion: 3.
- voltage: DC3.3V /DC5V.
- Input power: DC12V /DC24V.
- See more on Amazon...
Brand: Woedpez | Manufacturer: Woedpez
See On Amazon ï»ż
Looking For Something Else?
Search